Directive 2005/55/EC of the European Parliament and of the Council (repealed)Dangos y teitl llawn

ANNEX II U.K.

Appendix 1

Appendix 2 ESSENTIAL CHARACTERISTICS OF THE ENGINE FAMILY

Appendix 3

Appendix 4 CHARACTERISTICS OF THE ENGINE-RELATED VEHICLE PARTS

[F1 Appendix 5 OBD-RELATED INFORMATION

Textual Amendments

F1 Inserted by Commission Directive 2005/78/EC of 14 November 2005 implementing Directive 2005/55/EC of the European Parliament and of the Council on the approximation of the laws of the Member States relating to the measures to be taken against the emission of gaseous and particulate pollutants from compression-ignition engines for use in vehicles, and the emission of gaseous pollutants from positive ignition engines fuelled with natural gas or liquefied petroleum gas for use in vehicles and amending Annexes I, II, III, IV and VI thereto (Text with EEA relevance).

1. In accordance with the provisions of section 5 of Annex IV to Directive 2005/78/EC, the following additional information must be provided by the vehicle manufacturer for the purposes of enabling the manufacture of OBD-compatible replacement or service parts and diagnostic tools and test equipment, unless such information is covered by intellectual property rights or constitutes specific know-how of the manufacturer or the OEM supplier(s). U.K.

Where appropriate, the information given in this section shall be repeated in Appendix 2 to the EC type-approval certificate (Annex VI to this Directive):

1.1. A description of the type and number of the pre-conditioning cycles used for the original type approval of the vehicle. U.K.

1.2. A description of the type of the OBD demonstration cycle used for the original type-approval of the vehicle for the component monitored by the OBD system. U.K.

1.3. A comprehensive document describing all sensed components with the strategy for fault detection and MI activation (fixed number of driving cycles or statistical method), including a list of relevant secondary sensed parameters for each component monitored by the OBD system. A list of all OBD output codes and format used (with an explanation of each) associated with individual emission related powertrain components and individual non-emission related components, where monitoring of the component is used to determine MI activation. U.K.

1.3.1. The information required by this section may, for example, be defined by completing a table as follows, which shall be attached to this Annex: U.K.

Component	Fault code	Monitoring strategy	Fault detection criteria	MI activation criteria	Secondary parameters	Preconditioning	Demonstration test
SCR catalyst	Pxxxx	NO x sensor 1 and 2 signals	Difference between sensor 1 and sensor 2 signals	3 rd cycle	Engine speed, engine load, catalyst temperature, reagent activity	Three OBD test cycles (3 short ESC cycles)	OBD test cycle (short ESC cycle)

1.3.2. The information required by this Appendix may be limited to the complete list of the fault codes recorded by the OBD system where section 5.1.2.1 of Annex IV to Directive 2005/78/EC is not applicable as in the case of replacement or service components. This information may, for example, be defined by completing the two first columns of the table of section 1.3.1 above. U.K.

The complete information package should be made available to the type-approval authority as part of the additional material requested in section 6.1.7.1 of Annex I to this Directive, ‘ documentation requirements ’ .

1.3.3. The information required by this section shall be repeated in Appendix 2 to the EC type-approval certificate (Annex VI to this Directive). U.K.

Where section 5.1.2.1 of Annex IV to Directive 2005/78/EC is not applicable in the case of replacement or service components, the information provided in Appendix 2 to the EC type-approval certificate (Annex VI to this Directive) can be limited to the one mentioned in section 1.3.2.]

[F2 Appendix 6

Textual Amendments

F2 Inserted by Commission Directive 2008/74/EC of 18 July 2008 amending, as regards the type approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and access to vehicle repair and maintenance information, Directive 2005/55/EC of the European Parliament and of the Council and Directive 2005/78/EC (Text with EEA relevance).

Information required for roadworthiness testing U.K.

A. Measurement of carbon monoxide emissions (1) U.K.

3.2.1.6. Normal engine idling speed (including tolerance) … min ^-1 U.K.

3.2.1.6.1. High engine idling speed (including tolerance) … min ^-1 U.K.

3.2.1.7. Carbon monoxide content by volume in the exhaust gas with the engine idling (2) … % as stated by the manufacturer (positive ignition engines only) U.K.

B. Measurement of smoke opacity U.K.

3.2.13. Location of the absorption coefficient symbol (compression ignition engines only): … U.K.

4. TRANSMISSION (v) U.K.

4.3. Moment of inertia of engine flywheel: … U.K.

4.3.1. Additional moment of inertia with no gear engaged: …] U.K.

(1)

[F2 Numbering of the information document is consistent with the numbering used in the Type Approval Framework Directive (2008/74/EC).

(2)

Specify the tolerance.]

Textual Amendments

F2 Inserted by Commission Directive 2008/74/EC of 18 July 2008 amending, as regards the type approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and access to vehicle repair and maintenance information, Directive 2005/55/EC of the European Parliament and of the Council and Directive 2005/78/EC (Text with EEA relevance).