Commission Regulation (EU) No 748/2012Dangos y teitl llawn

SUBPART Q — IDENTIFICATION OF PRODUCTS, PARTS AND APPLIANCES U.K.

21.A.801 Identification of products U.K.

(a) The identification of products shall include the following information: U.K.

1.

manufacturer’s name;

2.

product designation;

3.

manufacturer’s Serial number;

4.

any other information the Agency finds appropriate.

(b) Any natural or legal person that manufactures an aircraft or engine under Subpart G or Subpart F shall identify that aircraft or engine by means of a fireproof plate that has the information specified in point (a) marked on it by etching, stamping, engraving, or other approved method of fireproof marking. The identification plate shall be secured in such a manner that it is accessible and legible, and will not likely be defaced or removed during normal service, or lost or destroyed in an accident. U.K.

(c) Any natural or legal person that manufactures a propeller, propeller blade, or propeller hub under Subpart G or Subpart F shall identify it by means of a plate, stamping, engraving, etching or other approved method of fireproof identification that is placed on it on a non-critical surface, contains the information specified in point (a), and will not likely be defaced or removed during normal service or lost or destroyed in an accident. U.K.

(d) For manned balloons, the identification plate prescribed in point (b) shall be secured to the balloon envelope and shall be located, if practicable, where it is legible to the operator when the balloon is inflated. In addition, the basket, load frame assembly and any heater assembly shall be permanently and legibly marked with the manufacturer’s name, part number, or equivalent, and serial number, or equivalent. U.K.

21.A.803 Handling of identification data U.K.

(a) No person shall remove, change, or place identification information referred to in point 21.A.801(a) on any aircraft, engine, propeller, propeller blade, or propeller hub, or in point 21.A.807(a) on an APU, without the approval of the Agency. U.K.

(b) No person shall remove or install any identification plate referred to in point 21.A.801, or in point 21.A.807 for an APU, without the approval of the Agency. U.K.

(c) By way of derogation from points (a) and (b), any natural or legal person performing maintenance work under the applicable associated implementing rules may, in accordance with methods, techniques and practices established by the Agency: U.K.

1.

remove, change, or place the identification information referred to in point 21.A.801(a) on any aircraft, engine, propeller, propeller blade, or propeller hub, or in point 21.A.807(a) on an APU; or

2.

remove an identification plate referred to in point 21.A.801, or point 21.A.807 for an APU, when necessary during maintenance operations.

(d) No person shall install an identification plate removed in accordance with point (c)(2) on any aircraft, engine, propeller, propeller blade, or propeller hub other than the one from which it was removed. U.K.

21.A.804 Identification of parts and appliances U.K.

(a) Each part or appliance shall be marked permanently and legibly with: U.K.

1.

a name, trademark, or symbol identifying the manufacturer in a manner identified by the applicable design data; and

2.

the part number, as defined in the applicable design data; and

3.

the letters EPA for parts or appliances produced in accordance with approved design data not belonging to the type-certificate holder of the related product, except for ETSO articles.

(b) By way of derogation from point (a), if the Agency agrees that a part or appliance is too small or that it is otherwise impractical to mark a part or appliance with any of the information required by point (a), the authorised release document accompanying the part or appliance or its container shall include the information that could not be marked on the part. U.K.

21.A.805 Identification of critical parts U.K.

In addition to the requirement of point 21.A.804, each manufacturer of a part to be fitted on a type-certificated product which has been identified as a critical part shall permanently and legibly mark that part with a part number and a serial number.

21.A.807 Identification of ETSO articles U.K.

(a) Each holder of an ETSO authorisation under Subpart O shall permanently and legibly mark each article with the following information: U.K.

1.

the name and address of the manufacturer;

2.

the name, type, part number or model designation of the article;

3.

the serial number or the date of manufacture of the article or both; and

4.

the applicable ETSO number.

(b) By way of derogation from point (a), if the Agency agrees that a part is too small or that it is otherwise impractical to mark a part with any of the information required by point (a), the authorised release document accompanying the part or its container shall include the information that could not be marked on the part. U.K.

(c) Each person who manufactures an APU under Subpart G or Subpart F shall identify that APU by means of a fireproof plate that has the information specified in point (a) marked on it by etching, stamping, engraving, or other approved method of fireproof marking. The identification plate shall be secured in such a manner that it is accessible and legible, and will not likely be defaced or removed during normal service, or lost or destroyed in an accident. U.K.