- Y Diweddaraf sydd Ar Gael (Diwygiedig)
- Gwreiddiol (Fel y’i mabwysiadwyd gan yr UE)
Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016 on personal protective equipment and repealing Council Directive 89/686/EEC (Text with EEA relevance)
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Mae unrhyw newidiadau sydd wedi cael eu gwneud yn barod gan y tîm yn ymddangos yn y cynnwys a chyfeirir atynt gydag anodiadau.Ar ôl y diwrnod ymadael bydd tair fersiwn o’r ddeddfwriaeth yma i’w gwirio at ddibenion gwahanol. Y fersiwn legislation.gov.uk yw’r fersiwn sy’n weithredol yn y Deyrnas Unedig. Y Fersiwn UE sydd ar EUR-lex ar hyn o bryd yw’r fersiwn sy’n weithredol yn yr UE h.y. efallai y bydd arnoch angen y fersiwn hon os byddwch yn gweithredu busnes yn yr UE. EUR-Lex Y fersiwn yn yr archif ar y we yw’r fersiwn swyddogol o’r ddeddfwriaeth fel yr oedd ar y diwrnod ymadael cyn cael ei chyhoeddi ar legislation.gov.uk ac unrhyw newidiadau ac effeithiau a weithredwyd yn y Deyrnas Unedig wedyn. Mae’r archif ar y we hefyd yn cynnwys cyfraith achos a ffurfiau mewn ieithoedd eraill o EUR-Lex. The EU Exit Web Archive legislation_originated_from_EU_p3
There are outstanding changes not yet made to Regulation (EU) 2016/425 of the European Parliament and of the Council. Any changes that have already been made to the legislation appear in the content and are referenced with annotations.
Revised legislation carried on this site may not be fully up to date. Changes and effects are recorded by our editorial team in lists which can be found in the ‘Changes to Legislation’ area. Where those effects have yet to be applied to the text of the legislation by the editorial team they are also listed alongside the legislation in the affected provisions. Use the ‘more’ link to open the changes and effects relevant to the provision you are viewing.
This Annex lays down the categories of risk against which PPE is intended to protect users.
Category I includes exclusively the following minimal risks:
superficial mechanical injury;
contact with cleaning materials of weak action or prolonged contact with water;
contact with hot surfaces not exceeding 50 °C;
damage to the eyes due to exposure to sunlight (other than during observation of the sun);
atmospheric conditions that are not of an extreme nature.
Category II includes risks other than those listed in Categories I and III;
Category III includes exclusively the risks that may cause very serious consequences such as death or irreversible damage to health relating to the following:
substances and mixtures which are hazardous to health;
atmospheres with oxygen deficiency;
harmful biological agents;
ionising radiation;
high-temperature environments the effects of which are comparable to those of an air temperature of at least 100 °C;
low-temperature environments the effects of which are comparable to those of an air temperature of – 50 °C or less;
falling from a height;
electric shock and live working;
drowning;
cuts by hand-held chainsaws;
high-pressure jets;
bullet wounds or knife stabs;
harmful noise.
PPE must provide adequate protection against the risks against which it is intended to protect.
PPE must be designed and manufactured so that, in the foreseeable conditions of use for which it is intended, the user can perform the risk-related activity normally whilst enjoying appropriate protection of the highest level possible.
The optimum level of protection to be taken into account in the design is that beyond which the constraints imposed by the wearing of the PPE would prevent its effective use during the period of exposure to the risk or the normal performance of the activity.
Where differing foreseeable conditions of use are such that several levels of the same risk can be distinguished, appropriate classes of protection must be taken into account in the design of the PPE.
PPE must be designed and manufactured so as not to create risks or other nuisance factors under foreseeable conditions of use.
The materials of which the PPE is made, including any of their possible decomposition products, must not adversely affect the health or safety of users.
Any part of the PPE that is in contact or is liable to come into contact with the user when the PPE is worn must be free of rough surfaces, sharp edges, sharp points and the like which could cause excessive irritation or injuries.
Any impediment caused by PPE to the actions to be carried out, the postures to be adopted and sensory perceptions shall be minimised. Furthermore, use of the PPE must not engender actions which might endanger the user.
PPE must be designed and manufactured in such a way as to facilitate its correct positioning on the user and to remain in place for the foreseeable period of use, bearing in mind ambient factors, the actions to be carried out and the postures to be adopted. For this purpose, it must be possible to adapt the PPE to fit the morphology of the user by all appropriate means, such as adequate adjustment and attachment systems or the provision of an adequate range of sizes.
PPE must be as light as possible without prejudicing its strength and effectiveness.
PPE must satisfy the specific additional requirements in order to provide adequate protection against the risks for which it is intended and PPE must be capable of withstanding environmental factors in the foreseeable conditions of use.
If the same manufacturer places on the market several PPE models of different types in order to ensure the simultaneous protection of adjacent parts of the body, they must be compatible.
Protective clothing containing removable protectors constitutes PPE and shall be assessed as a combination during conformity assessment procedures.
In addition to the name and address of the manufacturer, the instructions that must be supplied with the PPE must contain all relevant information on:
instructions for storage, use, cleaning, maintenance, servicing and disinfection. Cleaning, maintenance or disinfectant products recommended by manufacturers must have no adverse effect on the PPE or the user when applied in accordance with the relevant instructions;
performance as recorded during relevant technical tests to check the levels or classes of protection provided by the PPE;
where applicable, accessories that may be used with the PPE and the characteristics of appropriate spare parts;
where applicable, the classes of protection appropriate to different levels of risk and the corresponding limits of use;
where applicable, the month and year or period of obsolescence of the PPE or of certain of its components;
where applicable, the type of packaging suitable for transport;
the significance of any markings (see point 2.12);
the risk against which the PPE is designed to protect;
the reference to this Regulation and, where applicable, the references to other [F1relevant United Kingdom] legislation;
the name, address and identification number of the [F2approved] body or bodies involved in the conformity assessment of the PPE;
references to the relevant [F3designated] standard(s) used, including the date of the standard(s), or references to the other technical specifications used;
the internet address where the F4... declaration of conformity can be accessed.
Textual Amendments
F1Words in Annex 2 para. 1.4(i) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(45)(a)(i); 2020 c. 1, Sch. 5 para. 1(1)
F2Word in Annex 2 para. 1.4(j) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(45)(a)(ii); 2020 c. 1, Sch. 5 para. 1(1)
F3Word in Annex 2 para. 1.4(k) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(45)(a)(iii); 2020 c. 1, Sch. 5 para. 1(1)
F4Word in Annex 2 para. 1.4(l) omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(45)(a)(iv); 2020 c. 1, Sch. 5 para. 1(1)
The information referred to in points (i), (j), (k) and (l) need not be contained in the instructions supplied by the manufacturer if the F5... declaration of conformity accompanies the PPE.
Textual Amendments
F5Word in Annex 2 para. 1.4 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(45)(a)(v); 2020 c. 1, Sch. 5 para. 1(1)
If PPE incorporates adjustment systems, the latter must be designed and manufactured so that, after adjustment, they do not become undone unintentionally in the foreseeable conditions of use.
PPE must be designed and manufactured in a way that perspiration resulting from use is minimised. Otherwise it must be equipped with means of absorbing perspiration.
Any restriction of the user's face, eyes, field of vision or respiratory system by the PPE shall be minimised.
The screens for those types of PPE must have a degree of optical neutrality that is compatible with the degree of precision and the duration of the activities of the user.
If necessary, such PPE must be treated or provided with means to prevent misting-up.
Models of PPE intended for users requiring sight correction must be compatible with the wearing of spectacles or contact lenses.
If it is known that the design performance of new PPE may be significantly affected by ageing, the month and year of manufacture and/or, if possible, the month and year of obsolescence must be indelibly and unambiguously marked on each item of PPE placed on the market and on its packaging.
If the manufacturer is unable to give an undertaking with regard to the useful life of the PPE, his instructions must provide all the information necessary to enable the purchaser or user to establish a reasonable obsolescence month and year, taking into account the quality level of the model and the effective conditions of storage, use, cleaning, servicing and maintenance.
Where appreciable and rapid deterioration in PPE performance is likely to be caused by ageing resulting from the periodic use of a cleaning process recommended by the manufacturer, the latter must, if possible, affix a marking to each item of PPE placed on the market indicating the maximum number of cleaning operations that may be carried out before the equipment needs to be inspected or discarded. Where such a marking is not affixed, the manufacturer must give that information in his instructions.
Where the foreseeable conditions of use include, in particular, the risk of the PPE being caught up by a moving object thereby creating a danger for the user, the PPE must be designed and manufactured in such a way that a constituent part will break or tear, thereby eliminating the danger.
PPE intended for use in potentially explosive atmospheres must be designed and manufactured in such a way that it cannot be the source of an electric, electrostatic or impact-induced arc or spark likely to cause an explosive mixture to ignite.
Those types of PPE must be designed and manufactured in such a way as to minimise the time required for putting on and removing the equipment.
Where PPE comprises fixing systems enabling the PPE to be maintained in the correct position on the user or removed, it must be possible to operate such systems quickly and easily.
The instructions supplied by the manufacturer with PPE for intervention in very dangerous situations must include, in particular, data intended for competent, trained persons who are qualified to interpret them and ensure their application by the user.
The instructions must also describe the procedure to be adopted in order to verify that PPE is correctly adjusted and functional when worn by the user.
Where PPE incorporates an alarm which is activated in the absence of the level of protection normally provided, the alarm must be designed and placed so that it can be perceived by the user in the foreseeable conditions of use.
Where PPE incorporates components which can be attached, adjusted or removed by the user for replacement purposes, such components must be designed and manufactured so that they can be easily attached, adjusted and removed without tools.
Where PPE incorporates a connexion system permitting its connection to other complementary equipment, the means of attachment must be designed and manufactured in such a way as to enable it to be mounted only on appropriate equipment.
Where PPE incorporates a fluid circulation system, the latter must be chosen or designed and placed in such a way as to permit adequate fluid renewal in the vicinity of the entire part of the body to be protected, irrespective of the actions, postures or movements of the user under the foreseeable conditions of use.
Where PPE bears one or more identification markings or indicators directly or indirectly relating to health and safety, those identification markings or indicators must, if possible, take the form of F6... pictograms or ideograms. They must be perfectly visible and legible and remain so throughout the foreseeable useful life of the PPE. In addition, those markings must be complete, precise and comprehensible so as to prevent any misinterpretation. In particular, where such markings include words or sentences, the latter must be written in [F7English].
Textual Amendments
F6Word in Annex 2 para. 2.12 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(45)(b)(i)(aa); 2020 c. 1, Sch. 5 para. 1(1)
F7Word in Annex 2 para. 2.12 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(45)(b)(i)(bb); 2020 c. 1, Sch. 5 para. 1(1)
Where PPE is too small to allow all or part of the necessary marking to be affixed, the relevant information must be mentioned on the packaging and in the manufacturer's instructions.
PPE intended for foreseeable conditions of use in which the user's presence must be visibly and individually signalled must have one (or more) judiciously positioned means or devices for emitting direct or reflected visible radiation of appropriate luminous intensity and photometric and colorimetric properties.
PPE intended to protect the user against several potentially simultaneous risks must be designed and manufactured in such a way as to satisfy, in particular, the essential health and safety requirements specific to each of those risks.
PPE intended to protect against this type of risk must be sufficiently shock-absorbent to prevent injury resulting, in particular, from the crushing or penetration of the protected part, at least up to an impact-energy level above which the excessive dimensions or mass of the means of shock-absorption would preclude effective use of the PPE for the foreseeable period of wear.
The outsoles of protective footwear intended to prevent slipping must be designed and manufactured or equipped with additional means so as to ensure adequate grip, having regard to the nature or state of the surface.
PPE intended to prevent falls from a height or their effects must incorporate a body harness and a connexion system which can be connected to a reliable external anchorage point. It must be designed and manufactured so that, under the foreseeable conditions of use, the vertical drop of the user is minimised to prevent collision with obstacles while the braking force does not attain the threshold value at which physical injury or the opening or breakage of any PPE component which might cause the user to fall can be expected to occur.
Such PPE must also ensure that, after braking, the user is maintained in a correct position in which he may await help if necessary.
The manufacturer's instructions must specify, in particular, all relevant information relating to:
the characteristics required for the reliable external anchorage point and the necessary minimum clearance below the user;
the proper way of putting on the body harness and of attaching the connexion system to the reliable external anchorage point.
PPE designed to prevent the effects of mechanical vibrations must be capable of ensuring adequate attenuation of harmful vibration components for the part of the body at risk.
PPE designed to protect a part of the body against static compressive stress must be sufficiently capable of attenuating its effects so as to prevent serious injury or chronic complaints.
PPE constituent materials and other components designed to protect all or a part of the body against superficial injuries, such as abrasion, perforation, cuts or bites, must be chosen or designed and incorporated so as to ensure that those types of PPE provide sufficient resistance to abrasion, perforation and gashing (see also point 3.1) under the foreseeable conditions of use.
PPE designed to prevent drowning must be capable of returning to the surface as quickly as possible, without danger to health, a user who may be exhausted or unconscious after falling into a liquid medium, and of keeping the user afloat in a position which permits breathing while awaiting help.
PPE may be wholly or partially inherently buoyant or may be inflated by gas which can be manually or automatically released, or inflated orally.
Under the foreseeable conditions of use:
PPE must, without prejudice to its satisfactory operation, be capable of withstanding the effects of impact with the liquid medium and the environmental factors inherent in that medium;
inflatable PPE must be capable of inflating rapidly and fully.
Where particular foreseeable conditions of use so require, certain types of PPE must also satisfy one or more of the following additional requirements:
they must have all the inflation devices referred to in the second subparagraph, and/or a light or sound-signalling device;
they must have a device for hitching and attaching the body so that the user may be lifted out of the liquid medium;
they must be suitable for prolonged use throughout the period of activity exposing the user, possibly dressed, to the risk of falling into the liquid medium or requiring the user's immersion in it.
Clothing intended to ensure an effective degree of buoyancy, depending on its foreseeable use, shall be safe when worn and afford positive support in the liquid medium. In foreseeable conditions of use, this PPE must not restrict the user's freedom of movement but must enable the user, in particular, to swim or take action to escape from danger or to rescue other persons.
PPE intended to prevent the harmful effects of noise must be capable of attenuating the latter so that the exposure of the user does not exceed the limit values laid down [F8in the Control of Noise at Work Regulations 2005 (S.I. 2005/1643) and the Control of Noise at Work Regulations (Northern Ireland) 2006 (S.R. 2006 No.1)].
Textual Amendments
F8Words in Annex 2 para. 3.5 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(45)(c); 2020 c. 1, Sch. 5 para. 1(1)
Each item of PPE must bear labelling indicating the noise attenuation level provided by the PPE. Should that not be possible, the labelling must be fixed to the packaging.
PPE designed to protect all or a part of the body against the effects of heat and/or fire must possess thermal insulation capacity and mechanical strength appropriate to the foreseeable conditions of use.
Constituent materials and other components intended for protection against radiant and convective heat must possess an appropriate coefficient of transmission of incident heat flux and be sufficiently incombustible to preclude any risk of spontaneous ignition under the foreseeable conditions of use.
Where the external surface of those materials and components must be reflective, the reflective power must be appropriate to the intensity of the heat flux due to radiation in the infrared range.
Materials and other components of equipment intended for brief use in high-temperature environments and of PPE which may be splashed by hot products such as molten material must also possess sufficient thermal capacity to retain most of the stored heat until after the user has left the danger area and removed the PPE.
PPE materials and other components which may be splashed by hot products must also possess sufficient mechanical-impact absorbency (see point 3.1).
PPE materials and other components which may accidentally come into contact with flame and those used in the manufacture of industrial or fire-fighting equipment must also possess a degree of non-flammability and thermal or arc heat protection corresponding to the risk class associated with the foreseeable conditions of use. They must not melt when exposed to flames nor contribute to flame propagation.
Under the foreseeable conditions of use:
the quantity of heat transmitted by PPE to the user must be sufficiently low to prevent the heat accumulated during wear in the part of the body at risk from attaining, under any circumstances, the pain or health impairment threshold;
PPE must, if necessary, prevent liquid or steam penetration and must not cause burns resulting from contact between its protective integument and the user.
If PPE incorporates refrigeration devices for the absorption of incident heat by means of liquid evaporation or solid sublimation, the design of such devices must be such that any volatile substances released are discharged beyond the outer protective integument and not towards the user.
If PPE incorporates a breathing device, that device must adequately fulfil the protective function assigned to it under the foreseeable conditions of use.
The manufacturer's instructions accompanying PPE intended for brief use in high-temperature environments must, in particular, provide all relevant data for the determination of the maximum permissible user exposure to the heat transmitted by the equipment when used in accordance with its intended purpose.
PPE designed to protect all or a part of the body against the effects of cold must possess thermal insulating capacity and mechanical strength appropriate to the foreseeable conditions of use for which it is intended.
Constituent materials and other components suitable for protection against cold must possess a coefficient of transmission of incident thermal flux as low as required under the foreseeable conditions of use. Flexible materials and other components of PPE intended for use in a low-temperature environment must retain the degree of flexibility required for the necessary gestures and postures.
PPE materials and other components which may be splashed by cold products must also possess sufficient mechanical-impact absorbency (see point 3.1).
Under the foreseeable conditions of use, the following requirements apply:
the flux transmitted by PPE to the user must be sufficiently low to prevent the cold accumulated during wear at any point on the part of the body being protected, including the tips of fingers and toes in the case of hands or feet, from attaining, under any circumstances, the pain or health impairment threshold;
PPE must as far as possible prevent the penetration of such liquids as rain water and must not cause injuries resulting from contact between its cold protective integument and the user.
If PPE incorporates a breathing device, that device must adequately fulfil the protective function assigned to it under the foreseeable conditions of use.
The manufacturer's instructions accompanying PPE intended for brief use in low-temperature environments must provide all relevant data concerning the maximum permissible user exposure to the cold transmitted by the equipment.
PPE designed to protect all or part of the body against the effects of electric current must be sufficiently insulated against the voltages to which the user is likely to be exposed under the most unfavourable foreseeable conditions.
To this end, the constituent materials and other components of those types of PPE must be chosen or designed and incorporated so as to ensure that the leakage current measured through the protective integument under test conditions at voltages correlated with those likely to be encountered in situ is minimised and, in any event, below a maximum conventional permissible value which correlates with the tolerance threshold.
Together with their packaging, PPE types intended exclusively for use during work or activities in electrical installations which are or may be under tension must bear markings indicating, in particular, their protection class or corresponding operating voltage, their serial number and their date of manufacture. A space must also be provided outside the protective integument of such PPE for the subsequent inscription of the date of entry into service and those of the periodic tests or inspections to be conducted.
The manufacturer's instructions must indicate, in particular, the exclusive use for which those PPE types are intended and the nature and frequency of the dielectric tests to which they are to be subjected during their useful life.
Conductive PPE intended for live working at high voltages shall be designed and manufactured in such a way as to ensure that there is no difference of potential between the user and the installations on which he is intervening.
PPE designed to prevent acute or chronic eye damage from sources of non-ionising radiation must be capable of absorbing or reflecting the majority of the energy radiated in the harmful wavelengths without unduly affecting the transmission of the innocuous part of the visible spectrum, the perception of contrasts and the ability to distinguish colours where required by the foreseeable conditions of use.
To that end, eye protective equipment must be designed and manufactured so as to possess, for each harmful wavelength, a spectral transmission factor such that the radiant-energy illumination density capable of reaching the user's eye through the filter is minimised and under no circumstances exceeds the maximum permissible exposure value. PPE designed to protect the skin against non-ionising radiation must be capable of absorbing or reflecting the majority of the energy radiated in the harmful wavelengths.
Furthermore, the glasses must not deteriorate or lose their properties as a result of the effects of radiation emitted under the foreseeable conditions of use and all marketed specimens must bear the protection-factor number corresponding to the spectral distribution curve of their transmission factor.
Glasses suitable for radiation sources of the same type must be classified in the ascending order of their protection factors and the manufacturer's instructions must indicate, in particular, how to select the appropriate PPE taking into account the relevant conditions of use such as the distance from the source and the spectral distribution of the energy radiated at that distance.
The relevant protection factor number must be marked on all specimens of filtering eye protective equipment by the manufacturer.
PPE constituent materials and other components designed to protect all or a part of the body against radioactive dust, gases, liquids or mixtures thereof must be chosen or designed and incorporated so as to ensure that this equipment effectively prevents the penetration of the contaminants under the foreseeable conditions of use.
Depending on the nature or condition of these contaminants, the necessary leak-tightness can be provided by the impermeability of the protective integument and/or by any other appropriate means, such as ventilation and pressurisation systems designed to prevent the back-scattering of these contaminants.
Any decontamination measures to which PPE is subject must not prejudice its possible reuse during the foreseeable useful life of those types of equipment.
PPE intended to provide complete user protection against external irradiation or, failing this, adequate attenuation thereof, must be designed to counter only weak electron (e.g. beta) or weak photon (e.g. X, gamma) radiation.
The constituent materials and other components of these types of PPE must be chosen or designed and incorporated so as to provide the degree of user protection required by the foreseeable conditions of use without leading to an increase in exposure time as a result of the impedance of user gestures, posture or movement (see point 1.3.2).
PPE must bear a mark indicating the type and equivalent thickness of the constituent material(s) suitable for the foreseeable conditions of use.
PPE intended for the protection of the respiratory system must make it possible to supply the user with breathable air when exposed to a polluted atmosphere and/or an atmosphere having an inadequate oxygen concentration.
The breathable air supplied to the user by PPE must be obtained by appropriate means, for example after filtration of the polluted air through PPE or by supply from an external unpolluted source.
The constituent materials and other components of those types of PPE must be chosen or designed and incorporated so as to ensure appropriate user respiration and respiratory hygiene for the period of wear concerned under the foreseeable conditions of use.
The leak-tightness of the facepiece and the pressure drop on inspiration and, in the case of the filtering devices, purification capacity must keep contaminant penetration from a polluted atmosphere low enough not to be prejudicial to the health or hygiene of the user.
The PPE must bear details of the specific characteristics of the equipment which, in conjunction with the instructions, enable a trained and qualified user to employ the PPE correctly.
In the case of filtering equipment, the manufacturer's instructions must also indicate the time limit for the storage of new filters kept in their original packaging.
PPE intended to prevent the surface contact of all or part of the body with substances and mixtures which are hazardous to health or with harmful biological agents must be capable of preventing the penetration or permeation of such substances and mixtures and agents through the protective integument under the foreseeable conditions of use for which the PPE is intended.
To this end, the constituent materials and other components of those types of PPE must be chosen or designed and incorporated so as to ensure, as far as possible, complete leak-tightness, which will allow where necessary prolonged daily use or, failing this, limited leak-tightness necessitating a restriction of the period of wear.
Where, by virtue of their nature and the foreseeable conditions of their use, certain substances and mixtures which are hazardous to health or harmful biological agents possess high penetrative power which limits the duration of the protection provided by the PPE in question, the latter must be subjected to standard tests with a view to their classification on the basis of their performance. PPE which is considered to be in conformity with the test specifications must bear a marking indicating, in particular, the names or, in the absence of the names, the codes of the substances used in the tests and the corresponding standard period of protection. The manufacturer's instructions must also contain, in particular, an explanation of the codes (if necessary), a detailed description of the standard tests and all appropriate information for the determination of the maximum permissible period of wear under the different foreseeable conditions of use.
The breathing equipment must make it possible to supply the user with a breathable gaseous mixture, under foreseeable conditions of use and taking account in particular of the maximum depth of immersion.
Where the foreseeable conditions of use so require, the diving equipment must comprise the following:
a suit which protects the user against cold (see point 3.7) and/or pressure resulting from the depth of immersion (see point 3.2);
an alarm designed to give the user prompt warning of an approaching failure in the supply of breathable gaseous mixture (see point 2.8);
a lifesaving device enabling the user to return to the surface (see point 3.4.1).
The technical documentation shall specify the means used by the manufacturer to ensure the conformity of the PPE with the applicable essential health and safety requirements referred to in Article 5 and set out in Annex II.
The technical documentation shall include at least the following elements:
a complete description of the PPE and of its intended use;
an assessment of the risks against which the PPE is intended to protect;
a list of the essential health and safety requirements that are applicable to the PPE;
design and manufacturing drawings and schemes of the PPE and of its components, sub-assemblies and circuits;
the descriptions and explanations necessary for the understanding of the drawings and schemes referred to in point (d) and of the operation of the PPE;
the references of the [F9designated] standards referred to in Article 14 that have been applied for the design and manufacture of the PPE. In the event of partial application of [F9designated] standards, the documentation shall specify the parts which have been applied;
where [F10designated] standards have not been applied or have been only partially applied, descriptions of the other technical specifications that have been applied in order to satisfy the applicable essential health and safety requirements;
the results of the design calculations, inspections and examinations carried out to verify the conformity of the PPE with the applicable essential health and safety requirements;
reports on the tests carried out to verify the conformity of the PPE with the applicable essential health and safety requirements and, where appropriate, to establish the relevant protection class;
a description of the means used by the manufacturer during the production of the PPE to ensure the conformity of the PPE produced with the design specifications;
a copy of the manufacturer's instructions and information set out in point 1.4 of Annex II;
for PPE produced as a single unit to fit an individual user, all the necessary instructions for manufacturing such PPE on the basis of the approved basic model;
for PPE produced in series where each item is adapted to fit an individual user, a description of the measures to be taken by the manufacturer during the fitting and production process to ensure that each item of PPE complies with the approved type and with the applicable essential health and safety requirements.
Textual Amendments
F9Word in Annex 3 point (f) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(46)(a); 2020 c. 1, Sch. 5 para. 1(1)
F10Word in Annex 3 point (g) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(46)(b); 2020 c. 1, Sch. 5 para. 1(1)
The manufacturer shall establish the technical documentation described in Annex III.
The manufacturer shall take all measures necessary so that the manufacturing process and its monitoring ensure compliance of the manufactured PPE with the technical documentation referred to in point 2 and with the applicable requirements of this Regulation.
Textual Amendments
F13Word in Annex 4 para. 4.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(47)(b); 2020 c. 1, Sch. 5 para. 1(1)
A copy of the F14... declaration of conformity shall be made available to the relevant authorities upon request.
Textual Amendments
F14Word in Annex 4 para. 4.2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(47)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F11Word in Annex 4 para. 4 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(47)(a)(i); 2020 c. 1, Sch. 5 para. 1(1)
F12Word in Annex 4 para. 4 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(47)(a)(ii); 2020 c. 1, Sch. 5 para. 1(1)
The manufacturer's obligations set out in point 4 may be fulfilled by his authorised representative, on his behalf and under his responsibility, provided that they are specified in the mandate.
Textual Amendments
F16Word in Annex 5 para. 1 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(c); 2020 c. 1, Sch. 5 para. 1(1)
F17Words in Annex 5 para. 1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(b); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F18Word in Annex 5 para. 2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(c); 2020 c. 1, Sch. 5 para. 1(1)
The manufacturer shall lodge an application for F20... type-examination with a single [F21approved] body of his choice.
Textual Amendments
F20Word in Annex 5 para. 3 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(c); 2020 c. 1, Sch. 5 para. 1(1)
F21Word in Annex 5 para. 3 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(f); 2020 c. 1, Sch. 5 para. 1(1)
The application shall include:
the name and address of the manufacturer and, if the application is lodged by the authorised representative, his name and address as well;
a written declaration that the same application has not been lodged with any other [F21approved] body;
the technical documentation described in Annex III;
the specimen(s) of the PPE representative of the production envisaged. The [F21approved] body may request further specimens if needed for carrying out the test programme. For PPE produced in series where each item is adapted to fit an individual user, specimens shall be provided that are representative of the range of different users, and for PPE produced as a single unit to accommodate the special needs of an individual user, a basic model shall be provided.
Textual Amendments
F19Word in Annex 5 para. 3 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(a); 2020 c. 1, Sch. 5 para. 1(1)
The [F23approved] body shall:
Textual Amendments
F23Word in Annex 5 para. 4 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(e); 2020 c. 1, Sch. 5 para. 1(1)
examine the technical documentation to assess the adequacy of the technical design of the PPE. In conducting such an examination, point (j) of Annex III need not be taken into account;
for PPE produced in series where each item is adapted to fit an individual user, examine the description of the measures to assess their adequacy;
for PPE produced as a single unit to fit an individual user, examine the instructions for manufacturing such PPE on the basis of the approved basic model to assess their adequacy;
verify that the specimen(s) have been manufactured in conformity with the technical documentation, and identify the elements which have been designed in accordance with the applicable provisions of the relevant [F24designated] standards as well as the elements which have been designed in accordance with other technical specifications;
carry out appropriate examinations and tests, or have them carried out, to check whether, where the manufacturer has chosen to apply the solutions in the relevant [F24designated] standards, these have been applied correctly;
carry out appropriate examinations and tests, or have them carried out, to check whether, where the solutions in the relevant [F24designated] standards have not been applied, the solutions adopted by the manufacturer, including those in other technical specifications applied, meet the corresponding essential health and safety requirements and have been applied correctly.
Textual Amendments
F24Word in Annex 5 para. 4 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(g); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F22Word in Annex 5 para. 4 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(a) (with Sch. 35 para. 3(42)); 2020 c. 1, Sch. 5 para. 1(1)
The [F25approved] body shall draw up an evaluation report that records the activities undertaken in accordance with point 4 and their outcomes. Without prejudice to its obligations vis-à-vis the [F26Secretary of State], the [F25approved] body shall release the content of that report, in full or in part, only with the agreement of the manufacturer.
Textual Amendments
F25Word in Annex 5 para. 5 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(f); 2020 c. 1, Sch. 5 para. 1(1)
F26Words in Annex 5 para. 5 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(h); 2020 c. 1, Sch. 5 para. 1(1)
The period of validity of a newly issued certificate and, where appropriate, of a renewed certificate shall not exceed five years.
Textual Amendments
F28Word in Annex 5 para. 6.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(e); 2020 c. 1, Sch. 5 para. 1(1)
F29Word in Annex 5 para. 6.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(i); 2020 c. 1, Sch. 5 para. 1(1)
the name and identification number of the [F31approved] body;
the name and address of the manufacturer and, if the application is lodged by the authorised representative, the latter's name and address;
identification of the PPE covered by the certificate (type number);
a statement that the PPE type complies with the applicable essential health and safety requirements;
where [F32designated] standards have been fully or partially applied, the references of those standards or parts thereof;
where other technical specifications have been applied, their references;
where applicable, the performance level(s) or protection class of the PPE;
for PPE produced as a single unit to fit an individual user, the range of permissible variations of relevant parameters based on the approved basic model;
the date of issue, the date of expiry and, where appropriate, the date(s) of renewal;
any conditions attached to the issue of the certificate;
for category III PPE, a statement that the certificate shall only be used in conjunction with one of the conformity assessment procedures referred to in point (c) of Article 19.
Textual Amendments
F31Word in Annex 5 para. 6.2 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(e); 2020 c. 1, Sch. 5 para. 1(1)
F32Words in Annex 5 para. 6.2(e) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(j); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F30Word in Annex 5 para. 6.2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F33Word in Annex 5 para. 6.3 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F34Word in Annex 5 para. 6.4 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(e); 2020 c. 1, Sch. 5 para. 1(1)
F35Word in Annex 5 para. 6.4 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(i); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F27Word in Annex 5 para. 6 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F37Word in Annex 5 para. 7.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(f); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F38Word in Annex 5 para. 7.2 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(e); 2020 c. 1, Sch. 5 para. 1(1)
F39Word in Annex 5 para. 7.2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(d); 2020 c. 1, Sch. 5 para. 1(1)
in the case of a modification to the approved type referred to in point 7.2;
in the case of a change in the state of the art referred to in point 7.3;
at the latest, before the date of expiry of the certificate.
In order to allow the [F40approved] body to fulfil its tasks, the manufacturer shall submit his application at the earliest 12 months and at the latest 6 months prior to the expiry date of the F41... type-examination certificate.
Textual Amendments
F40Word in Annex 5 para. 7.4 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(f); 2020 c. 1, Sch. 5 para. 1(1)
F41Word in Annex 5 para. 7.4 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(d); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F42Word in Annex 5 para. 7.5 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(f); 2020 c. 1, Sch. 5 para. 1(1)
F43Word in Annex 5 para. 7.5 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(d); 2020 c. 1, Sch. 5 para. 1(1)
his name and address and data identifying the F45... type-examination certificate concerned;
confirmation that there has been no modification to the approved type as referred to in point 7.2, including materials, sub-components or sub-assemblies, nor to the relevant [F46designated] standards or other technical specifications applied;
confirmation that there has been no change in the state of the art as referred to in point 7.3;
where not already supplied, copies of current product drawings and photographs, product marking and information supplied by the manufacturer; and
for category III products, where not already available to the [F44approved] body, information on the results of the supervised product checks at random intervals carried out in accordance with Annex VII, or on the results of audits of his quality system carried out in accordance with Annex VIII.
Textual Amendments
F45Word in Annex 5 para. 7.6 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(d); 2020 c. 1, Sch. 5 para. 1(1)
F46Words in Annex 5 para. 7.6(b) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(j); 2020 c. 1, Sch. 5 para. 1(1)
Where the [F44approved] body has confirmed that no modification to the approved type referred to in point 7.2 and no change in the state of the art referred to in point 7.3 has occurred, the simplified review procedure shall be applied and the examinations and tests referred to in point 7.5 shall not be carried out. In such cases, the [F44approved] body shall renew the F45... type-examination certificate.
The costs associated with that renewal shall be proportionate to the administrative burden of the simplified procedure.
If the [F44approved] body finds that a change in the state of the art referred to in point 7.3 has occurred, the procedure set out in point 7.5 shall apply.
Textual Amendments
F44Word in Annex 5 para. 7.6 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(f); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F47Word in Annex 5 para. 7.7 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(e); 2020 c. 1, Sch. 5 para. 1(1)
F48Word in Annex 5 para. 7.7 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F36Word in Annex 5 para. 7 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F49Word in Annex 5 para. 8 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(f); 2020 c. 1, Sch. 5 para. 1(1)
F50Words in Annex 5 para. 8 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(k)(i); 2020 c. 1, Sch. 5 para. 1(1)
F51Word in Annex 5 para. 8 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(d) ; 2020 c. 1, Sch. 5 para. 1(1)
Each [F49approved] body shall inform the other [F49approved] bodies concerning the F51... type-examination certificates and/or any additions thereto which it has refused, withdrawn, suspended or otherwise restricted, and, upon request, concerning such certificates and/or additions thereto which it has issued.
[F52The Secretary of State] and the other [F49approved] bodies may, on request, obtain a copy of the F51... type-examination certificates and/or additions thereto. [F53The Secretary of State may on request] obtain a copy of the technical documentation and the results of the examinations carried out by the [F49approved] body.
Textual Amendments
F52Words in Annex 5 para. 8 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(k)(ii)(aa); 2020 c. 1, Sch. 5 para. 1(1)
F53Words in Annex 5 para. 8 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(k)(ii)(bb); 2020 c. 1, Sch. 5 para. 1(1)
The [F49approved] body shall keep a copy of the F51... type-examination certificate, its annexes and additions, as well as the technical file including the documentation submitted by the manufacturer, for a period of five years after the expiry of the validity of that certificate.
Textual Amendments
F54Word in Annex 5 para. 9 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F15Word in Annex 5 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(48)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F55Word in Annex 6 para. 1 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(49)(a); 2020 c. 1, Sch. 5 para. 1(1)
The manufacturer shall take all measures necessary so that the manufacturing process and its monitoring ensure conformity of the manufactured PPE with the type described in the F56... type-examination certificate and with the applicable requirements of this Regulation.
Textual Amendments
F56Word in Annex 6 para. 2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(49)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F59Word in Annex 6 para. 3.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(49)(c); 2020 c. 1, Sch. 5 para. 1(1)
F60Word in Annex 6 para. 3 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(49)(b); 2020 c. 1, Sch. 5 para. 1(1)
A copy of the F60... declaration of conformity shall be made available to the relevant authorities upon request.
Textual Amendments
F57Word in Annex 6 para. 3 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(49)(c); 2020 c. 1, Sch. 5 para. 1(1)
F58Word in Annex 6 para. 3 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(49)(a); 2020 c. 1, Sch. 5 para. 1(1)
The manufacturer's obligations set out in point 3 may be fulfilled by his authorised representative, on his behalf and under his responsibility, provided that they are specified in the mandate.
Textual Amendments
F61Word in Annex 7 para. 1 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
The manufacturer shall take all measures necessary so that the manufacturing process and its monitoring ensure the homogeneity of production and conformity of the manufactured PPE with the type described in the F62... type-examination certificate and with the applicable requirements of this Regulation.
Textual Amendments
F62Word in Annex 7 para. 2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
Before placing PPE on the market, the manufacturer shall lodge an application for supervised product checks at random intervals with a single [F63approved] body of his choice.
Textual Amendments
F63Word in Annex 7 para. 3 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(b)(i); 2020 c. 1, Sch. 5 para. 1(1)
The application shall include the following:
the name and address of the manufacturer and, if the application is lodged by the authorised representative, his name and address;
a written declaration that the same application has not been lodged with any other [F63approved] body;
the identification of the PPE concerned.
Where the chosen body is not the body that has carried out the F64... type-examination, the application shall also include the following:
Textual Amendments
F64Word in Annex 7 para. 3 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(b)(ii); 2020 c. 1, Sch. 5 para. 1(1)
the technical documentation described in Annex III;
a copy of the F64... type-examination certificate.
Textual Amendments
F65Word in Annex 7 para. 4.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(c); 2020 c. 1, Sch. 5 para. 1(1)
F66Word in Annex 7 para. 4.1 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F67Word in Annex 7 para. 4.2 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(c); 2020 c. 1, Sch. 5 para. 1(1)
F68Word in Annex 7 para. 4.2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F69Word in Annex 7 para. 4.3 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(c); 2020 c. 1, Sch. 5 para. 1(1)
F70Word in Annex 7 para. 4.3 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(d); 2020 c. 1, Sch. 5 para. 1(1)
F71Word in Annex 7 para. 4.3 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F72Word in Annex 7 para. 4.4 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(c); 2020 c. 1, Sch. 5 para. 1(1)
F73Word in Annex 7 para. 4.4 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F74Word in Annex 7 para. 4.6 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
F75Word in Annex 7 para. 4.6 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(c); 2020 c. 1, Sch. 5 para. 1(1)
F76Words in Annex 7 para. 4.6 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(e); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F77Word in Annex 7 para. 5.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F78Word in Annex 7 para. 5.3 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(f); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F81Word in Annex 7 para. 6.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(g); 2020 c. 1, Sch. 5 para. 1(1)
F82Word in Annex 7 para. 6.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(c); 2020 c. 1, Sch. 5 para. 1(1)
F83Word in Annex 7 para. 6.1 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
A copy of the F84... declaration of conformity shall be made available to the relevant authorities upon request.
Textual Amendments
F84Word in Annex 7 para. 6.2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(h); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F79Word in Annex 7 para. 6 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(g); 2020 c. 1, Sch. 5 para. 1(1)
F80Word in Annex 7 para. 6 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(50)(a); 2020 c. 1, Sch. 5 para. 1(1)
The manufacturer's obligations may be fulfilled by his authorised representative, on his behalf and under his responsibility, provided that they are specified in the mandate. An authorised representative may not fulfil the manufacturer's obligations set out in point 2.
Textual Amendments
F85Word in Annex 8 para. 1 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(a); 2020 c. 1, Sch. 5 para. 1(1)
The manufacturer shall operate an approved quality system for production, final product inspection and testing of the PPE concerned as specified in point 3, and shall be subject to surveillance as specified in point 4.
Textual Amendments
F86Word in Annex 8 para. 3.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(d); 2020 c. 1, Sch. 5 para. 1(1)
The application shall include:
the name and address of the manufacturer and, if the application is lodged by the authorised representative, his name and address as well;
the address of the manufacturer's premises where the audits can be carried out;
a written declaration that the same application has not been lodged with any other [F86approved] body;
the identification of the PPE concerned;
the documentation concerning the quality system.
Where the chosen body is not the body that has carried out the F87... type-examination, the application shall also include the following:
Textual Amendments
F87Word in Annex 8 para. 3.1 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(b); 2020 c. 1, Sch. 5 para. 1(1)
the technical documentation of the PPE described in Annex III;
a copy of the F87... type-examination certificate.
Textual Amendments
F88Word in Annex 8 para. 3.2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(a); 2020 c. 1, Sch. 5 para. 1(1)
All the elements, requirements and provisions adopted by the manufacturer shall be documented in a systematic and orderly manner in the form of written policies, procedures and instructions. The quality system documentation shall permit a consistent interpretation of the quality programmes, plans, manuals and records.
The quality system documentation shall, in particular, contain an adequate description of:
the quality objectives and the organisational structure, responsibilities and powers of the management with regard to product quality;
the corresponding manufacturing, quality control and quality assurance techniques, processes and systematic actions that will be used;
the examinations and tests that will be carried out before, during and after manufacture, and the frequency with which they will be carried out;
the quality records, such as inspection reports and test data, calibration data and qualification reports on the personnel concerned; and
the means of monitoring the achievement of the required product quality and the effective operation of the quality system.
Textual Amendments
F89Word in Annex 8 para. 3.3 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(c); 2020 c. 1, Sch. 5 para. 1(1)
It shall presume conformity with those requirements in respect of the elements of the quality system that comply with the corresponding specifications of the relevant [F90designated] standard.
Textual Amendments
F90Word in Annex 8 para. 3.3 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(e); 2020 c. 1, Sch. 5 para. 1(1)
In addition to experience in quality management systems, the auditing team shall have at least one member with experience of evaluation in the field of PPE and technology concerned, and knowledge of the applicable essential health and safety requirements. The audit shall include an assessment visit to the manufacturer's premises. The auditing team shall review the technical documentation of the PPE referred to in point 3.1 to verify the manufacturer's ability to identify the applicable essential health and safety requirements and to carry out the necessary examinations with a view to ensuring conformity of the PPE with those requirements.
The result of that assessment shall be notified to the manufacturer. The notification shall contain the conclusions of the audit and the reasoned assessment decision.
Textual Amendments
F91Word in Annex 8 para. 3.5 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(d); 2020 c. 1, Sch. 5 para. 1(1)
The [F91approved] body shall evaluate any proposed changes and decide whether the modified quality system will continue to satisfy the requirements referred to in point 3.2 or whether a reassessment is necessary.
It shall notify the manufacturer of its decision. The notification shall contain the conclusions of the examination and the reasoned assessment decision.
Textual Amendments
F92Word in Annex 8 para. 3.6 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(d); 2020 c. 1, Sch. 5 para. 1(1)
F93Word in Annex 8 para. 3.6 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F95Word in Annex 8 para. 4.2 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(c); 2020 c. 1, Sch. 5 para. 1(1)
the quality system documentation;
the quality records, such as inspection reports and test data, calibration data and qualification reports on the personnel concerned.
Textual Amendments
F96Word in Annex 8 para. 4.3 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F97Word in Annex 8 para. 4.4 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(d); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F94Word in Annex 8 para. 4 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F100Word in Annex 8 para. 5.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(f); 2020 c. 1, Sch. 5 para. 1(1)
F101Word in Annex 8 para. 5.1 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(c); 2020 c. 1, Sch. 5 para. 1(1)
F102Word in Annex 8 para. 5.1 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F103Word in Annex 8 para. 5.2 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(b); 2020 c. 1, Sch. 5 para. 1(1)
F104Words in Annex 8 para. 5.2 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(g)(i); 2020 c. 1, Sch. 5 para. 1(1)
A copy of the F103... declaration of conformity shall be made available to the [F105enforcement authority] upon request.
Textual Amendments
F105Words in Annex 8 para. 5.2 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(g)(ii); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F98Word in Annex 8 para. 5 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(f); 2020 c. 1, Sch. 5 para. 1(1)
F99Word in Annex 8 para. 5 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F106Words in Annex 8 para. 6 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(h); 2020 c. 1, Sch. 5 para. 1(1)
the documentation referred to in point 3.1;
the information related to the change referred to in point 3.5, as approved;
the decisions and reports of the [F107approved] body referred to in points 3.5, 4.3 and 4.4.
Textual Amendments
F107Word in Annex 8 para. 6 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F108Word in Annex 8 para. 7 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(d); 2020 c. 1, Sch. 5 para. 1(1)
F109Words in Annex 8 para. 7 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(51)(i); 2020 c. 1, Sch. 5 para. 1(1)
The [F108approved] body shall inform the other [F108approved] bodies of quality system approvals which it has refused, suspended, withdrawn or otherwise restricted, and, upon request, of such quality system approvals which it has issued.
The manufacturer's obligations set out in points 3.1, 3.5, 5 and 6 may be fulfilled by his authorised representative, on his behalf and under his responsibility, provided that they are specified in the mandate.
Textual Amendments
F110Word in Annex 9 heading omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(52)(a); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F111Words in Annex 9 para. 5 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(52)(b); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F112Word in Annex 9 para. 6 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(52)(c); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F113Word in Annex 9 para. 7 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(52)(d); 2020 c. 1, Sch. 5 para. 1(1)
F114Word in Annex 9 para. 7 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(52)(e); 2020 c. 1, Sch. 5 para. 1(1)
Textual Amendments
F115Word in Annex 9 para. 8 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(52)(d); 2020 c. 1, Sch. 5 para. 1(1)
Signed for and on behalf of: …
(place and date of issue):
(name, function) (signature):
Directive 89/686/EEC | This Regulation |
---|---|
Article 1(1) | Articles 1 and 2(1) |
Article 1(2) and (3) | Article 3 point (1) |
Article 1(4) | Article 2(2) |
Article 2(1) | Article 4 |
Article 2(2) | Article 6 |
Article 2(3) | Article 7(2) |
Article 3 | Article 5 |
Article 4(1) | Article 7(1) |
Article 4(2) | — |
Article 5(1), (4), (5) | — |
Article 5(2) | Article 14 |
Article 6 | Article 44 |
Article 7 | Articles 37-41 |
Article 8(1) | Article 8(2) first subparagraph |
Article 8(2)-(4) | Articles 18 and 19 and Annex I |
Article 9 | Articles 20, 24(1), 25, and 30(1) |
Article 10 | Annex V |
Article 11(A) | Annex VII |
Article 11(B) | Annex VIII |
Article 12(1) | Article 15 |
Articles 12(2) and 13 | Articles 16 and 17 |
Article 14 | — |
Article 15 | — |
Article 16(1) first subparagraph and (2) | — |
Article 16(1) second subparagraph | Article 48(2) |
Annex I | Article 2(2) |
Annex II | Annex II |
Annex III | Annex III |
Annex IV | Article 16 |
Annex V | Article 24(2)-(11) |
Annex VI | Annex IX |
It is optional for the manufacturer to assign a number to the declaration of conformity.
The Whole Regulation you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.
Would you like to continue?
Y Rhestrau you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.
Would you like to continue?
Y Diweddaraf sydd Ar Gael (diwygiedig):Y fersiwn ddiweddaraf sydd ar gael o’r ddeddfwriaeth yn cynnwys newidiadau a wnaed gan ddeddfwriaeth ddilynol ac wedi eu gweithredu gan ein tîm golygyddol. Gellir gweld y newidiadau nad ydym wedi eu gweithredu i’r testun eto yn yr ardal ‘Newidiadau i Ddeddfwriaeth’.
Gwreiddiol (Fel y’i mabwysiadwyd gan yr UE): Mae'r wreiddiol version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Rhychwant ddaearyddol: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Dangos Llinell Amser Newidiadau: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Gallwch wneud defnydd o ddogfennau atodol hanfodol a gwybodaeth ar gyfer yr eitem ddeddfwriaeth o’r tab hwn. Yn ddibynnol ar yr eitem ddeddfwriaeth sydd i’w gweld, gallai hyn gynnwys:
Mae’r llinell amser yma yn dangos y fersiynau gwahanol a gymerwyd o EUR-Lex yn ogystal ag unrhyw fersiynau dilynol a grëwyd ar ôl y diwrnod ymadael o ganlyniad i newidiadau a wnaed gan ddeddfwriaeth y Deyrnas Unedig.
Cymerir dyddiadau fersiynau’r UE o ddyddiadau’r dogfennau ar EUR-Lex ac efallai na fyddant yn cyfateb â’r adeg pan ddaeth y newidiadau i rym ar gyfer y ddogfen.
Ar gyfer unrhyw fersiynau a grëwyd ar ôl y diwrnod ymadael o ganlyniad i newidiadau a wnaed gan ddeddfwriaeth y Deyrnas Unedig, bydd y dyddiad yn cyd-fynd â’r dyddiad cynharaf y daeth y newid (e.e. ychwanegiad, diddymiad neu gyfnewidiad) a weithredwyd i rym. Am ragor o wybodaeth gweler ein canllaw i ddeddfwriaeth ddiwygiedig ar Ddeall Deddfwriaeth.
Defnyddiwch y ddewislen hon i agor dogfennau hanfodol sy’n cyd-fynd â’r ddeddfwriaeth a gwybodaeth am yr eitem hon o ddeddfwriaeth. Gan ddibynnu ar yr eitem o ddeddfwriaeth sy’n cael ei gweld gall hyn gynnwys:
liciwch ‘Gweld Mwy’ neu ddewis ‘Rhagor o Adnoddau’ am wybodaeth ychwanegol gan gynnwys