Additional driveline components (ADC) information document U.K.
Information document no.: | Issue: Date of issue: Date of Amendment: |
pursuant to …
[F1ADC type/family (if applicable):]
Textual Amendments
F1 Substituted by Commission Regulation (EU) 2019/318 of 19 February 2019 amending Regulation (EU) 2017/2400 and Directive 2007/46/EC of the European Parliament and of the Council as regards the determination of the CO2 emissions and fuel consumption of heavy-duty vehicles (Text with EEA relevance).
…
0.GENERALU.K.
0.1Name and address of manufacturerU.K.
0.2Make (trade name of manufacturer):U.K.
0.3ADC type:U.K.
0.4ADC family:U.K.
0.5ADC type as separate technical unit/ADC family as separate technical unitU.K.
0.6Commercial name(s) (if available):U.K.
0.7Means of identification of model, if marked on the ADC:U.K.
0.8In the case of components and separate technical units, location and method of affixing of the EC approval mark:U.K.
0.9Name(s) and address(es) of assembly plant(s):U.K.
0.10Name and address of the manufacturer's representative:U.K.
PART 1U.K. ESSENTIAL CHARACTERISTICS OF THE (PARENT) ADC AND THE ADC TYPES WITHIN AN ADC FAMILY
Parent-ADC | Family member | ||||
#1 | #2 | #3 | |||
F20.0GENERALU.K.
F20.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
F20.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
F20.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
F20.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
F20.5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
F20.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
F20.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
F20.8.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
F20.9.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .U.K.
Textual Amendments
1.0SPECIFIC ADC/ANGLE DRIVE INFORMATIONU.K.
1.1Gear ratio and gearschemeU.K.
1.2Angle between input/output shaftU.K.
1.3Type of bearings at corresponding positionsU.K.
1.4Number of teeth per gearwheelU.K.
1.5Single gear widthU.K.
1.6Number of dynamic shaft sealsU.K.
1.7Oil viscosity (± 10 %)U.K.
1.8Surface roughness of the teethU.K.
1.9Specified oil level in reference to central axis and in accordance with the drawing specification (based on average value between lower and upper tolerance) in static or running condition. The oil level is considered as equal if all rotating transmission parts (except for the oil pump and the drive thereof) are located above the specified oil levelU.K.
1.10Oil level within (± 1mm).U.K.
LIST OF ATTACHMENTSU.K.
No.: | Description: | Date of issue: |
---|---|---|
1 | Information on ADC test conditions | … |
2 | … |