Search Legislation

Directive 2003/25/EC of the European Parliament and of the CouncilShow full title

Directive 2003/25/EC of the European Parliament and of the Council of 14 April 2003 on specific stability requirements for ro-ro passenger ships (Text with EEA relevance)

 Help about what version

What Version

More Resources

 Help about UK-EU Regulation

Legislation originating from the EU

When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.

Close

This item of legislation originated from the EU

Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).

Status:

EU Directives are published on this site to aid cross referencing from UK legislation. Since IP completion day (31 December 2020 11.00 p.m.) no amendments have been applied to this version.

  1. Introductory Text

  2. Article 1.Purpose

  3. Article 2.Definitions

  4. Article 3.Scope

  5. Article 4.Significant wave heights

  6. Article 5.Sea areas

  7. Article 6.Specific stability requirements

  8. Article 7.Introduction of the specific stability requirements

  9. Article 8.Certificates

  10. Article 9.Seasonal and short-time period operations

  11. Article 10. Amendment of Annexes

  12. Article 10a. Exercise of the delegation

  13. Article 11. Committee procedure

  14. Article 12.Penalties

  15. Article 13.Implementation

  16. Article 14.Entry into force

  17. Article 15.Addressees

    1. ANNEX I

      SPECIFIC STABILITY REQUIREMENTS FOR RO-RO PASSENGER SHIPS

      1. 1. In addition to the requirements of Regulation II-1/B/8 of the...

        1. 1.1. The provisions of Regulation II-1/B/8.2.3 shall be complied with when...

        2. 1.2. When a high-efficiency drainage system is installed, the administration of...

        3. 1.3. For ships in geographically defined restricted areas of operation, the...

        4. 1.4. As an alternative to the requirements of paragraph 1.1 or...

        5. 1.5. reference to acceptance of the results of the model test...

        6. 1.6. the information supplied to the master in accordance with Regulations...

      2. 2. For assessing the effect of the volume of the assumed...

        1. 2.1. a transverse or longitudinal bulkhead shall be considered intact if...

        2. 2.2. in cases where the ship's hull is structurally partly widened...

        3. 2.3. the tightness of transverse or longitudinal bulkheads which are taken...

        4. 2.4. for special arrangements such as, e.g., full-width hanging decks and...

        5. 2.5. the effect of the volume of the assumed accumulated sea...

        6. 2.6. When a bulkhead above the ro-ro deck is assumed damaged,...

      3. 3. When determining significant wave height, the wave heights given on...

        1. 3.1. For ships which are to be operated only for a...

      4. 4. Model tests shall be conducted in accordance with the Appendix....

      5. Appendix

        1. Model test method

          1. 1. Objectives

          2. 2. Definitions

          3. 3. Ship model

            1. 3.1. The model should copy the actual ship for both outer...

              1. 3.1.1. ± 35 % L BP from midship;

              2. 3.1.2. an additional test will be required for the worst damage...

            2. 3.2. The model should comply with the following:

              1. 3.2.1. length between perpendiculars (L BP ) is to be at...

              2. 3.2.2. hull thickness of flooded spaces should not exceed 4 mm;

              3. 3.2.3. in both intact and damaged conditions, the model should satisfy...

              4. 3.2.4. all damaged compartments and ro-ro spaces should be modelled with...

              5. 3.2.5. the characteristics of motion of the actual ship should be...

              6. 3.2.6. main design features such as watertight bulkheads, air escapes, etc.,...

              7. 3.2.7. the shape of the damage opening should be as follows:...

            3. 3.3. The model in the flooded equilibrium condition should be heeled...

          4. 4. Procedure for experiments

            1. 4.1. The model should be tested in a long-crested irregular seaway...

              1. 4.1.1. the basin width should be sufficient to avoid contact or...

              2. 4.1.2. the basin depth should be sufficient for proper wave modelling...

              3. 4.1.3. for a representative wave realisation to be used, measurements should...

              4. 4.1.4. the wave probe closer to the wave maker should be...

              5. 4.1.5. variation in H S and T P should be within...

              6. 4.1.6. during the tests, for approval purposes, a tolerance of + 2,5 %...

            2. 4.2. The model should be free to drift and placed in...

              1. 4.2.1. heading control lines, intended for minor adjustment, should be located...

              2. 4.2.2. the carriage speed should be equal to the actual drift...

            3. 4.3. At least 10 experiments should be carried out. The test...

          5. 5. Survival criteria

          6. 6. Test documentation

            1. 6.1. The model test programme should be approved by the Administration...

            2. 6.2. Tests should be documented by means of a report and...

    2. ANNEX II

      INDICATIVE GUIDELINES TO NATIONAL ADMINISTRATIONS

      1. PART I APPLICATION

        1. Paragraph 1

        2. Paragraph 1.1

          1. 1. This paragraph addresses the application of a hypothetical amount of...

          2. 2. The accumulated water is added as a liquid load with...

          3. 3. If fr is 2,0 m or more, no water is assumed...

        3. Paragraph 1.2

        4. Paragraph 1.3

          1. 1. The amount of assumed accumulated water on deck may, in...

          2. 2. If the significant wave height (hs), in the area concerned,...

          3. 3. The height hw is kept constant, therefore the amount of...

          4. 4. If the calculations to demonstrate compliance with this Directive relate...

        5. Paragraphs 1.4 and 1.5

        6. Paragraph 1.6

        7. Paragraph 2.1

        8. Paragraph 2.2

        9. Paragraph 2.3

          1. 1. Transverse or longitudinal bulkheads/barriers which are fitted and taken into...

          2. 2. The height (Bh) of transverse and longitudinal bulkheads/barriers shall be...

        10. Paragraph 2.5.1

        11. Paragraph 2.5.2

        12. Paragraph 2.5.3

        13. Paragraph 2.6

          1. 1. The statutory extent of damage is to be applied along...

          2. 2. All transverse and longitudinal bulkheads/barriers which constrain the assumed accumulated...

          3. 3. In those cases where the transverse bulkhead/barrier is damaged the...

      2. PART II MODEL TESTING

        1. Paragraph 3 — Ship model

          1. 3.1. The material of which the model is made is not...

          2. 3.2. Model particulars

            1. 3.2.1. In recognising that scale effects play an important role in...

            2. 3.2.2. The model in way of the assumed damages must be...

            3. 3.2.3. It is important that not only the draughts in the...

            4. 3.2.4. After measuring the damaged draughts it may be found necessary...

            5. 3.2.5. In order to ensure that the model motion characteristics represent...

            6. 3.2.6. It is assumed that the ventilators of the damage compartment...

            7. 3.2.7. It is deemed appropriate to consider a damage shape representative...

          3. 3.3. In the original model test method of resolution 14 of...

          4. 3.4. In cases where there is a margin in GM in...

        2. Paragraph 4 — Procedure for experiments

          1. 4.1. Wave spectra

          2. 4.2. To avoid interference of the mooring system with the ship...

          3. 4.3. A sufficient number of tests in different wave trains is...

        3. Paragraph 5 — Survival criteria

        4. Paragraph 6 — Test approval

        5. Note:

Back to top

Options/Help

Print Options

Close

Legislation is available in different versions:

Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.

Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.

Close

Opening Options

Different options to open legislation in order to view more content on screen at once

Close

More Resources

Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:

  • the original print PDF of the as adopted version that was used for the EU Official Journal
  • lists of changes made by and/or affecting this legislation item
  • all formats of all associated documents
  • correction slips
  • links to related legislation and further information resources
Close

Timeline of Changes

This timeline shows the different versions taken from EUR-Lex before exit day and during the implementation period as well as any subsequent versions created after the implementation period as a result of changes made by UK legislation.

The dates for the EU versions are taken from the document dates on EUR-Lex and may not always coincide with when the changes came into force for the document.

For any versions created after the implementation period as a result of changes made by UK legislation the date will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. For further information see our guide to revised legislation on Understanding Legislation.

Close

More Resources

Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:

  • the original print PDF of the as adopted version that was used for the print copy
  • correction slips

Click 'View More' or select 'More Resources' tab for additional information including:

  • lists of changes made by and/or affecting this legislation item
  • confers power and blanket amendment details
  • all formats of all associated documents
  • links to related legislation and further information resources