The Weighing Equipment (Automatic Catchweighing Instruments) Regulations 2003

PART II U.K. GENERAL REQUIREMENTS FOR USE FOR TRADE

General duties for use for trade U.K.

5.  No person shall use for trade an automatic catchweighing instrument unless—

(a) it has been erected and installed in accordance with the requirements of Schedule 2; and

(b) the requirements of Schedule 3 in respect of its use and manner of use are complied with.

Requirements to be satisfied for passing as fit for use for trade U.K.

6.  Every automatic catchweighing instrument shall, before it is passed as fit for use for trade,—

(a) comply with a pattern in respect of which a certificate of approval remains in force at the time when such instrument is so passed;

(b) have affixed to it the applicable descriptive markings relating to that automatic catchweighing instrument and have provision for a place for the application of the specified verification marks, in accordance with the requirements of Schedule 4; and

(c) subject to regulation 9, have successfully undergone initial verification testing and, as part of that testing, an accuracy class has been confirmed in respect of it; for the purposes of these Regulations, initial verification testing means testing of an automatic catchweighing instrument in accordance with the procedure specified in clause 5.3 (initial verification) of Part 1 of OIML R51 or on an equivalent basis.

Supplementary indications U.K.

7.  Where the indication of the exact quantity of material an automatic catchweighing instrument purports to weigh is given in metric units of measurement that indication may also be given by means of a supplementary indicationF1 ....

Textual Amendments

F1 Words in reg. 7 omitted (1.1.2010) by virtue of The Weights and Measures (Metrication Amendments) Regulations 2009 (S.I. 2009/3045), regs. 1, 3(2)(k)

Supplementary requirements U.K.

8.—(1) Every automatic catchweighing instrument submitted for testing shall be completely assembled and in a clean condition.

(2) For the purposes of the performance by an inspector of his functions under the Act or these Regulations relating to inspection, testing, passing as fit for use for trade and stamping of any automatic catchweighing instrument, a person submitting such an instrument to an inspector or who an inspector has reasonable cause to believe has control of such an instrument for use for trade shall, if requested, provide for the inspector’s use such material as the inspector may reasonably require, and a control instrument: any material or control instrument so provided shall be returned to the person in question.

(3) An automatic catchweighing instrument which has been dismantled and transported before use shall not be tested, passed as fit for use for trade and stamped unless it has been completely erected ready for use and, subject to paragraph (4), installed in the position in which it is to be used.

(4) An automatic catchweighing instrument that has not been dismantled, or one where an inspector is satisfied that any dismantling and re-assembly or transportation to its intended place of use could not, in his opinion, affect the accuracy or functioning of the automatic catchweighing instrument, may be tested, with a view to passing that instrument as fit for use for trade, at a place other than the intended place of use, for the purposes of initial verification testing.

Automatic catchweighing instruments imported from [F2 an EEA State] U.K.

9.—(1) In relation to an automatic catchweighing instrument imported into Great Britain from [F3 an EEA State], subject to paragraph (3), an inspector shall not carry out any test relating to initial verification testing if, together with the automatic catchweighing instrument being imported, he is presented with the requisite documentation.

(2) In this regulation and regulation 10(2)—

(a) “requisite documentation” means—

(i) the test report of an approved body that the automatic catchweighing instrument which is the subject of that report has been tested on the same basis as the procedure specified in clause 5.3 (initial verification) of Part 1 of OIML R51 or on an equivalent basis, and stating which tests have been applied to it; and

(ii) the test results relating to those tests;

(b) “EEA State” means a State which is a Contracting Party to the EEA Agreement F4 ...; and in this paragraph “the EEA Agreement” means the Agreement on the European Economic Area signed at Oporto on 2nd May 1992 as adjusted by the Protocol signed at Brussels on 17th March 1993; and

(c) a body is an “approved body” for the purposes of this regulation if it is a body in a member State or in an EEA State which has responsibility in that State for metrological control of automatic catchweighing instruments or is a laboratory which has been accredited for the purposes of testing automatic catchweighing instruments in a member State or in an EEA State as being a body which conforms with the criteria set out in BS EN ISO/IEC 17025:2000 M1 .

(3) Nothing in these Regulations shall prevent an inspector carrying out initial verification testing where he is not satisfied—

(a) as to the authenticity of the test report or the results presented to him; or

(b) that the test results presented to him are results which in fact relate to the automatic catchweighing instrument being imported; or

(c) subject to regulation 8(4), that the automatic catchweighing instrument has not been dismantled after the tests to which the test report relates were carried out.

Textual Amendments

F2 Words in reg. 9 heading substituted (31.12.2020) by The Weighing and Measuring Equipment and Meters (Amendment of Secondary Legislation) (EU Exit) Regulations 2018 (S.I. 2018/1387), reg. 1(2), Sch. para. 14(2)(a); 2020 c. 1, Sch. 5 para. 1(1)

F3 Words in reg. 9(1) substituted (31.12.2020) by The Weighing and Measuring Equipment and Meters (Amendment of Secondary Legislation) (EU Exit) Regulations 2018 (S.I. 2018/1387), reg. 1(2), Sch. para. 14(2)(b); 2020 c. 1, Sch. 5 para. 1(1)

F4 Words in reg. 9(2)(b) omitted (31.12.2020) by virtue of The Weighing and Measuring Equipment and Meters (Amendment of Secondary Legislation) (EU Exit) Regulations 2018 (S.I. 2018/1387), reg. 1(2), Sch. para. 14(2)(c); 2020 c. 1, Sch. 5 para. 1(1)

Marginal Citations

M1 BS EN ISO/1EC 17025:2000 is the international standard “General requirements for the competence of testing and calibration laboratories” (ISBN 0 580 34929 2).