8. In Schedule 2—
(a)omit paragraph 5 (amendment of Commission Regulation (EC) No 278/2009);
(b)in paragraph 19 (amendment of Commission Regulation (EU) No 813/2013, in sub-paragraph (4)(b)—
(i)omit the inserted paragraph 4(b)(i);
(ii)after the inserted paragraph 4(b) insert—
“(ba)for “the Community”, in the first four places it occurs, there were substituted “Great Britain”;”;
(iii)after paragraph 4(e) insert—
“(f)in paragraph 9, for “the Community market” there were substituted “the market of Great Britain”;”;
(iv)omit the inserted paragraph 5(b)(i);
(v)after the inserted paragraph (5)(b) insert—
“(ba)in the description of Module C: Conformity to type, in paragraph 3—
(i)for “the Community”, in the first place it occurs, there were substituted “Great Britain”;
(ii)for “the Community market” there were substituted “the market of Great Britain”;
(bb)for “the Community”, in each other place it occurs, there were substituted “Great Britain”;”;
(c)in paragraph 22 (amendment of Commission Regulation (EU) No 548/2014)—
(i)after sub-paragraph (1) insert—
“(1A) In Article 1 (subject matter and scope)—
(a)in paragraph 2(l), for “Directive 94/9/EC of the European Parliament and of the Council” substitute “the Equipment and Protective Systems Intended for Use in Potentially Explosive Atmospheres Regulations 2016”(1);
(b)in paragraph 2(o), for “Article 3 of Council Directive 2009/71/Euratom” substitute “section 26 of the Nuclear Installations Act 1965”(2);
(c)in paragraph 3, omit “This is without prejudice to the legal obligations under other Union’s harmonisation legislation that these products could be subject to”.”;
(ii)in sub-paragraph (2)—
(aa)for “In Article 2 (definitions),” substitute—
“In Article 2 (definitions)—
(a)”;
(bb)after sub-paragraph (2)(a) insert—
“(b)In point (17), for “point 2 of Annex IV to Directive 2009/125/EC” substitute “paragraph 1(2)(b) of Schedule 1A to the Ecodesign for Energy-Related Products Regulations 2010”(3).”;
(iii)after sub-paragraph (2) insert—
“(2A) In Article 3 (eco-design requirements), omit the second paragraph.”.”;
(iv)in sub-paragraph (3)—
(aa)for “For Article 4 (conformity assessment) substitute—” substitute—
“In Article 4 (conformity assessment)—
(a)for paragraph 1, substitute—”;
(bb)after sub-paragraph (3)(a), insert—
“(b)in paragraph 2, for “Article 8 of Directive 2009/125/EC” substitute “regulation 4(2)(a) of the Ecodesign for Energy-Related Products Regulations 2010.”(4).”;
(v)in sub-paragraph (4), for “the United Kingdom” substitute “Great Britain”;
(vi)in sub-paragraph (6), for “Article 8” substitute “Article 9”;
(vii)for sub-paragraph (7) substitute—
“(7) In Annex 2 (measurement and calculation methods)—
(a)in the first paragraph, omit the words from “including” to “Union”;
(b)the second paragraph, for “relevant harmonised standards” substitute “designated standards”.(5)”;
(viii)in sub-paragraph (8)—
(aa)in paragraph (a), for “United Kingdom” substitute “Great Britain”;
(bb)in paragraph (b), for “the second paragraph” substitute “the third paragraph”, and for “the United Kingdom” substitute “Great Britain”;
(cc)after paragraph (b) insert—
“(ba)in the final paragraph of point (1), omit the words from “The Member State authorities” to “non-compliance of the model”.”.
(dd)in paragraph (e), for “the fourth paragraph” substitute “the fifth paragraph”.
S.I. 2010/2617; Schedule 1A was inserted by S.I. 2019/539.
Regulation 4(2) was amended by S.I. 2019/539.
See regulations 2 and 2A of S.I. 2010/2617 (as amended by S.I. 2019/539) for the meaning of “designated standard”; that definition applies to Commission Regulation (EU) No 548/2014 by virtue of paragraph 22(2) of Schedule 2 to S.I. 2019/539.