The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022

PART 4 EU Regulations

CHAPTER 1 Regulation (EU) 2018/858

Regulation (EU) 2018/858

22.  Regulation (EU) 2018/858 is amended in accordance with regulations 23 to 48.

Amendments to Chapter I

23.—(1) In Article 2(3) (scope), in the words after sub-paragraph (c), for “Directive 2006/42/EC of the European Parliament and of the Council” substitute “the Supply of Machinery (Safety) Regulations 2008(1)”.

(2) In Article 3 (definitions)—

(a) in point (2), for “this Regulation” substitute “Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market authorisation of motor vehicles and their trailers, and of systems, components and separate technical units, as it has effect in EU law”;

(b) after point (2), insert—

“(2A) “GB type-approval’ means the procedure whereby the approval authority certifies that a type of vehicle, system, component or separate technical unit satisfies the relevant administrative provisions and technical requirements of this Regulation;”;

(c) in point (3)—

(i) after “procedure” insert “in Article 42”;

(ii) for “an approval” substitute “the approval”;

(iii) omit the words from “laid down” to the end;

(d) after point (5), insert—

“(5A) “EU certificate of conformity” means the document issued by the manufacturer which certifies that a produced vehicle conforms to the approved type of vehicle and complies with all regulatory acts that were applicable in the European Union at the time of its production;

(5B) “GB certificate of conformity” means the document issued by the manufacturer which certifies that a produced vehicle conforms to the approved type of vehicle and complies with this Regulation;

(5C) “UK (NI) certificate of conformity” means that document issued by the manufacturer which certifies that a produced vehicle conforms to the approved type of vehicle and complies with all regulatory acts that were applicable in Northern Ireland at the time of its production, but does not include, for the purposes of this Regulation, a certificate of conformity relating to a UK (NI) national small series type-approval issued under regulation 16(7) of the Road Vehicles (Approval) Regulations 2020(2);”;

(e) in point (6), omit “EU individual vehicle approval or national”;

(f) in point (9), for “EU” substitute “GB”;

(g) in point (10), for “an approval” substitute “the approval”;

(h) in point (11), for “EU” substitute “GB”;

(i) in points (12), (13) and (14), for “an approval” substitute “the approval”;

(j) in point (34), for “relevant Union harmonisation” substitute “applicable”;

(k) in point (35)—

(i) omit “national”,

(ii) omit “on the territory of the Member State”;

(l) in point (36)—

(i) omit “of a Member State, notified to the Commission by that Member State,”;

(ii) omit “for acting as the contact point for the approval authorities of the other Member States,”;

(m) omit point (37);

(n) in point (39), for the definition of “national accreditation body”, substitute—

““national accreditation body” means—

(a)

the UK national accreditation body as defined in point (11) of Article 2 of Regulation (EC) No 765/2008(3), or

(b)

in cases where a technical service is located in a member State, the accreditation body as defined in point (11) of Article 2 of Regulation (EC) No 765/2008(4) as it has effect in EU law;”;

(o) in point (41) and (42), for “the Union” substitute “Great Britain”;

(p) in point (50) and (52), for “the Union” substitute “Great Britain”;

(q) after point (58), insert—

“(59) “EU Type Approval Regulation” means Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, as that Regulation has effect in EU law, as amended from time to time, and as it has effect by virtue of the Northern Ireland Protocol;

(60) “qualifying Northern Ireland goods” has the meaning given in section 47 of the United Kingdom Internal Market Act 2020(5);

(61) “retained direct EU legislation” has the meaning given in section 20 of the European Union (Withdrawal) Act 2018(6);

(62) “the Northern Ireland Protocol” means the Protocol on Ireland/Northern Ireland in the EU withdrawal agreement.”.

(3) In Article 4(2), in the second subparagraph, for “The Commission is empowered to adopt delegated acts in accordance with Article 82, amending” substitute “The Secretary of State may by regulations, amend”.

Amendments to Chapter II

24.—(1) In Article 5 (technical requirements)—

(a) in paragraph 1, after “technical units” insert “for which approval is sought under this Regulation”.

(b) in paragraph 2—

(i) in point (a), for “EU” substitute “GB”;

(ii) in point (c), and in the second subparagraph, for “, market surveillance authorities or the Commission”, substitute “or market surveillance authorities”;

(c) in paragraph 3, for “The Commission is empowered to adopt delegated acts in accordance with Article 82, amending”, substitute “The Secretary of State may by regulations amend”.

(2) After Article 5, insert—

“Article 5A Recognition of EU type approvals in Great Britain

1.   Subject to compliance by manufacturers, distributors, importers and other economic operators with their obligations as set out in Articles 13, 14, 16, 17, 18, 19, 20, 38, 48, 50, 51 and 52, nothing in this Regulation, or in the regulatory acts listed in Annex II, prohibits the placing on the market, registration or entry into service in Great Britain of any vehicle, or any system, component or separate technical unit, to which this Article applies.

2.   This Article applies to the following vehicles—

(a) a vehicle which was in the United Kingdom before IP completion day, and a trailer which was in the United Kingdom before 1st January 2023, provided that the manufacturer of the vehicle or trailer holds a relevant EU approval in relation to that vehicle or trailer;

(b) a vehicle in relation to which the manufacturer holds a valid type-approval certificate issued by the Secretary of State under section 55(1A) or (1D) of the Road Traffic Act 1988(7);

(c) a vehicle in relation to which the manufacturer holds a relevant NI approval;

(d) a vehicle—

(i) which is a qualifying Northern Ireland good, and

(ii) in relation to which the manufacturer holds a relevant EU approval;

(e) an incomplete vehicle—

(i) to which Article 22(4A) applies, and

(ii) in respect of which the manufacturer holds a relevant EU approval.

3.   This Article applies to the following systems, components and separate technical units—

(a) a system, component or separate technical unit which was manufactured before 1st January 2023 in relation to which the manufacturer holds a relevant EU approval;

(b) a system, component or separate technical unit in relation to which the manufacturer holds a valid type-approval certificate issued by the Secretary of State under section 55(1A) or (1D) of the Road Traffic Act 1988;

(c) a system, component or separate technical unit in relation to which the manufacturer holds a relevant NI approval;

(d) a system, component or separate technical unit—

(i) which is a qualifying Northern Ireland good, and

(ii) in relation to which the manufacturer holds a relevant EU approval;

(e) any system or component fitted to a complete or an incomplete vehicle—

(i) to which Article 22(4A) applies, and

(ii) in relation to which the manufacturer holds a relevant EU approval.

4.   For the purposes of this Regulation—

(a) “a relevant EU approval” means a valid EU type-approval or EU individual vehicle approval issued—

(i) before IP completion day by a member State other than the United Kingdom in accordance with this Regulation as it has effect in EU law, or

(ii) on or after IP completion day in accordance with the EU Type Approval Regulation by a member State,

and includes any such approval which is revised or extended;

(b) “a relevant NI approval” means a valid EU type-approval, EU individual vehicle approval, national small series type-approval or national individual vehicle approval issued by the Secretary of State on or after IP completion day in accordance with the EU Type Approval Regulation as it has effect by virtue of the Northern Ireland Protocol, and includes any such approval which is revised or extended.

5.   This Article applies without prejudice to Article 50(6).”

(3) In Article 6 (obligations of Member States)—

(a) in the heading, for “Member States” substitute “the authorities”;

(b) omit paragraphs 1 to 3;

(c) for paragraph 4, substitute—

“4.   Vehicles, systems, components and separate technical units may only be placed on the market, registered or entered into service if they comply with this Regulation, or, where Article 5A applies to the vehicle, system or component, with the EU Type Approval Regulation.”;

(d) in paragraph 5—

(i) in the first subparagraph, for “Member States shall” substitute “The Secretary of State must”;

(ii) in the second subparagraph—

(aa) for “Member States” substitute “the Secretary of State”;

(bb) for the words from “harmonised dimensions” to the end, substitute “dimensions laid down in regulations 7 and 8 of the Road Vehicles (Construction and Use) Regulations 1986(8) and weights and axle loads laid down in regulation 4 of the Road Vehicles (Authorised Weight) Regulations 1998(9)”;

(e) in paragraph 6, for “Member States shall” substitute “The market surveillance authority must”;

(f) omit paragraph 7;

(g) in paragraph 8—

(i) in the first and second subparagraphs, for “Member States shall” substitute “The Secretary of State must”;

(ii) in the first subparagraph, omit the words from “, and the results thereof” to the end;

(iii) omit the third subparagraph;

(h) in paragraph 9—

(i) in the first and second subparagraphs, for “Member States shall” substitute “The Secretary of State must”;

(ii) in the first subparagraph, omit the words “and the results thereof” to the end;

(iii) omit the third subparagraph;

(i) omit paragraph 10.

(4) In Article 7 (obligations of approval authorities)—

(a) for “Approval authorities” each time it occurs, substitute “The approval authority”;

(b) in paragraph 1, at the end, insert “or, in the case of a relevant NI approval (within the meaning of Article 5A), the EU Type Approval Regulation”;

(c) in paragraph 2—

(i) in the first subparagraph—

(aa) for “They shall” substitute “It must”;

(bb) omit the words from “the obligation laid down” to “and to other”;

(cc) for “Union law” substitute “the law of the United Kingdom or of any part of the United Kingdom”;

(dd) for “in the Union” substitute “in the United Kingdom”;

(ii) omit the second subparagraph;

(d) in paragraph 3—

(i) for “market surveillance authorities”, both times it occurs, substitute “the market surveillance authority”;

(ii) for “approval authorities” substitute “the approval authority”;

(iii) for “EU type-approval certificate” substitute “GB type-approval certificate”;

(e) in paragraph 4, for “an approval authority” substitute “the approval authority”.

(5) In Article 8 (obligation of market surveillance authorities)—

(a) in paragraphs 1, 3, 8, 10, 12, for “Market surveillance authorities” each time it occurs, substitute “The market surveillance authority”;

(b) in paragraphs 1, 2, 9, 11 and 13, for “market surveillance authorities” substitute “market surveillance authority”;

(c) in paragraph 1, in point (c) of the second subparagraph—

(i) omit “the information exchanged in the Forum and”;

(ii) for “the implementing acts referred to in Article 13(10)” substitute “any retained direct EU legislation made under Article 13(10) as it had effect before IP completion day, or any regulations made under Article 13(10) as it is now in force”;

(d) in paragraph 2—

(i) in the first subparagraph—

(aa) omit “of each Member State”;

(bb) omit “per Member State”;

(cc) for “in that Member State” substitute “in Great Britain”;

(ii) in the second subparagraph, at the end insert “or, where Article 5A applies to the vehicle, the applicable regulatory acts listed in Annex II of the EU Type Approval Regulation.”;

(e) omit paragraphs 4 to 7;

(f) in paragraph 8—

(i) for “to the authorities”, substitute “to the authority”;

(ii) for “authorities consider” substitute “authority considers”;

(g) in paragraph 10—

(i) omit “within the territories of their Member States”;

(ii) omit “or the Commission”;

(h) in paragraph 11—

(i) omit “of one Member State”;

(ii) for “decide” substitute “decides”;

(iii) omit “relevant”;

(i) in paragraph 12—

(i) omit the words from “to the obligation” to “available to the Commission and”;

(ii) for “Union law” substitute “the law of the United Kingdom, or any part of the United Kingdom”;

(iii) for “in the Union” substitute “in the United Kingdom”;

(j) omit paragraphs 13 to 15.

(6) Omit Articles 9 to 11.

(7) In Article 12 (online data exchange)—

(a) omit paragraph 1;

(b) in paragraph 2—

(i) in the first and second subparagraphs—

(aa) for “Member States”, both times it occurs, substitute “the Secretary of State”;

(bb) omit “in the common secure electronic exchange system,” both times it occurs;

(ii) for the third subparagraph, substitute—

“The Secretary of State may by regulations establish the format of, and the criteria for, public access to the information referred to in the first and second subparagraphs of this paragraph.”;

(c) omit paragraph 3;

(d) in paragraph 4—

(i) in the first paragraph—

(aa) for the words from the beginning to “in order to” substitute “The Secretary of State must”;

(bb) for “EU” both times it occurs, substitute “GB”;

(cc) for “1 September 2022” substitute “1 September 2024”;

(ii) for the second paragraph, substitute—

“The Secretary of State may by regulations establish the format of, and the criteria for, public access to the information referred to in the first subparagraph of this paragraph.”;

(e) in paragraph 5—

(i) for “Commission” substitute “Secretary of State”;

(ii) for “implementing acts” substitute “regulations”.

(8) In Article 13 (general obligations of manufacturers)—

(a) in paragraph 1—

(i) after “this Regulation” insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, the EU Type Approval Regulation”;

(ii) at the end, for “those in Article 5” substitute “the requirements of Article 5 of the Regulation in question”;

(b) in paragraph 4—

(i) for “EU type-approval” both times it occurs, substitute “GB type-approval”;

(ii) for “the Union” each time it occurs, substitute “Great Britain”;

(c) in paragraph 5, after “this Regulation”, insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, the EU Type Approval Regulation”;

(d) in paragraph 8, for “the Union” substitute “Great Britain”;

(e) in paragraph 9, at the end insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, in the EU Type Approval Regulation”;

(f) in paragraph 10—

(i) in the first subparagraph—

(aa) omit “without prejudice to Article 9(5) and”;

(bb) for “Union and national law” substitute “the law of the United Kingdom or of any part of the United Kingdom”;

(ii) for the second subparagraph, substitute—

“For the purposes of the first subparagraph of this paragraph, the Secretary of State may by regulations specify—

(a) the data to be made available free of charge, and

(b) the requirements to be met by third parties to demonstrate that they have—

(i) a legitimate interest in public safety or environmental protection, and

(ii) recourse to adequate testing facilities.”.

(9) In Article 14 (obligations of manufacturers concerning their vehicles etc that are not in conformity or that present a serious risk)—

(a) in paragraph 1—

(i) in the first subparagraph, after “Regulation” insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, the EU Type Approval Regulation,”;

(ii) in the second subparagraph, omit “that granted the type-approval”;

(b) in paragraph 2, for “authorities” both times it occurs, substitute “authority”;

(c) in paragraph 3—

(i) in the first subparagraph, for “EU” each time it occurs, substitute “GB”;

(ii) in the second subparagraph—

(aa) for “authorities” substitute “authority”;

(bb) at the end, insert “and, where Article 5A applies to a vehicle, a copy of any EU certificate of conformity or UK (NI) certificate of conformity”;

(d) in paragraph 4—

(i) omit the first subparagraph;

(ii) in the second subparagraph, for “a national authority” substitute “the approval authority or the market surveillance authority”.

(10) In Article 15 (obligations of manufacturer’s representatives)—

(a) in paragraph 1—

(i) for “authorities” each time it occurs, substitute “authority”;

(ii) in point (a)—

(aa) for “EU” each time it occurs, substitute “GB”;

(bb) for “one of the official Union languages” substitute “English”;

(iii) in point (b), for “an approval authority” substitute “the approval authority”;

(b) in paragraph 2, in the first paragraph, for the words from “both” to the end substitute “the approval authority”.

(11) In Article 16 (obligations of importers)—

(a) in paragraph 1, at the end, insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, with the EU Type Approval Regulation”;

(b) in paragraph 2, in the first subparagraph—

(i) for “EU” substitute “GB”;

(ii) after “certificate”, insert “or a type-approval certificate which is valid under the EU Type Approval Regulation, as appropriate,”;

(iii) after “Article 13(8)” insert “of this Regulation or, where applicable, of the EU Type Approval Regulation”;

(c) in paragraph 3, after “Regulation” insert “or of the EU Type Approval Regulation, where applicable”;

(d) in paragraph 4—

(i) for “market surveillance authorities” substitute “market surveillance authority”;

(ii) omit “that granted the type-approval”;

(e) in paragraph 6—

(i) after “Article 59,” insert “of this Regulation or, where applicable, of the EU Type Approval Regulation”;

(ii) for the words from “the official language” to the end, substitute “English”;

(f) in paragraph 9, at the end, insert “or, where applicable, in the EU Type Approval Regulation”.

(12) In Article 17 (obligations of importers concerning their vehicles etc, that are not in conformity or that present a serious risk)—

(a) for “authorities”, each time it occurs, substitute “authority”;

(b) for “EU” each time it occurs, substitute “GB”;

(c) in paragraph 1—

(i) after “this Regulation” insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, the EU Type Approval Regulation”;

(ii) omit “that granted the EU type-approval”;

(d) after paragraph 3, insert—

“3A.   Where Article 5A applies to a vehicle, system, component or separate technical unit, the importer must—

(a) keep a copy of any EU type-approval certificate which applies to the vehicle, system or component in question, including the attachments referred to in Article 28(1) of the EU Type Approval Regulation, for a period of—

(i) ten years after the end of the validity of the EU type-approval of a vehicle, and

(ii) five years after the end of the validity of the EU type-approval of a system, component or separate technical unit, and

(b) ensure that the certificate and attachments referred to in subparagraph (a) can be made available to the approval authority and the market surveillance authority on request.”;

(e) in paragraph 4—

(i) for “a national authority” both times it occurs”, substitute “the approval authority or the market surveillance authority”;

(ii) in the first subparagraph—

(aa) after “unit” insert “with this Regulation or, where applicable, the EU Type Approval Regulation”;

(bb) for the words from “a language” to the end, substitute “English”.

(13) In Article 18 (obligations of distributors)—

(a) in paragraph 1—

(i) after “Article 59” insert “of this Regulation, or, where Article 5A applies to a vehicle, system, component or separate technical unit, of the EU Type Approval Regulation”;

(ii) for “the official language or languages of the relevant member State” substitute “English”;

(iii) at the end insert “of this Regulation or, where Article 5A applies, of the EU Type Approval Regulation”;

(b) in paragraph 3, at the end insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, in the EU Type Approval Regulation”.

(14) In Article 19 (obligations of distributors concerning vehicles etc not in conformity or presenting a serious risk)—

(a) in paragraph 1—

(i) after “this Regulation” insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, the EU Type Approval Regulation”;

(ii) omit “that granted the EU type-approval”;

(b) in paragraph 2—

(i) after “this Regulation”, insert “or, where Article 5A applies to a vehicle, system, component or separate technical unit, the EU Type Approval Regulation”;

(ii) omit “that granted the EU type-approval”;

(c) in paragraph 3—

(i) for “authorities” both times it occurs, substitute “authority”;

(ii) omit the words from “of the Member States” to the end;

(d) in paragraph 4, for “a national authority” substitute “the approval authority or the market surveillance authority”.

(15) In Article 20 (cases in which obligations of manufacturers apply to importers and distributors)—

(a) in point (b)—

(i) for “the Union” both times it occurs, substitute “Great Britain”;

(ii) omit “the territory of the”;

(b) at the end of point (b), insert—

“;

(c) where the importer or distributor makes available on the market or is responsible for the entry into service of a vehicle, system, component or separate technical unit to which Article 5A applies on the basis of a relevant EU approval or a relevant NI approval that was granted to a manufacturer outside Great Britain, and it is not possible to identify a manufacturer’s representative in Great Britain”.

(16) In Article 21 (identification of economic operators), in the opening words—

(a) for “an approval” substitute “the approval”;

(b) for “a market” substitute “the market”.

Amendments to Chapter III

25.—(1) In the heading to Chapter III, for “EU” substitute “GB”.

(2) In Article 22 (procedures for EU type-approval)—

(a) in the heading, and in paragraphs 4 and 5, for “EU” each time it occurs, substitute “GB”;

(b) after paragraph 4, insert—

“4A.   Until 31 July 2026 for M and N category vehicles, and 31 July 2027 for O category vehicles, where the approval authority is considering whether to grant multi-stage type-approval in respect of a completed vehicle, it may, for the purposes of paragraphs 3 and 4 of this Article, paragraphs 2 and 6 of Article 26, and paragraphs 2.1, 3.2 and 4.1 of Annex IX, consider any EU type-approvals which are valid under the EU Type Approval Regulation and have been issued in respect of the incomplete or complete vehicle or its systems and components, as valid GB type-approvals granted under this Regulation pursuant to the technical requirements in the regulatory acts listed in Annex II.

4B.   Paragraph 4A does not apply where the approval authority is considering whether to grant multi-stage type-approval to a single manufacturer, or two or more manufacturers who are part of a group of connected manufacturers, as defined in Article 3(2) of Regulation (EU) 2019/631 of the European Parliament and of the Council of 17 April 2019 setting CO2 emission performance standards for new passenger cars and for new light commercial vehicles(10).”.

(3) In Article 23 (application for EU type-approval)—

(a) in the heading, and in paragraph 1, for “EU”;

(b) substitute “GB”;

(c) in paragraph 2—

(i) in the first subparagraph, omit the second sentence;

(ii) omit the second subparagraph;

(d) omit paragraph 3.

(4) In Article 24 (information folder)—

(a) in paragraph 1—

(i) in point (a), for “implementing acts referred to in paragraph 4” substitute “retained direct EU legislation made under paragraph 4 as it had effect before IP completion day, or regulations made under paragraph 4 as it is now in force, except where paragraph 1A applies”;

(ii) in point (d), for “EU” substitute “GB”;

(b) after paragraph 1, insert—

“1A.   The information document submitted as part of an information folder accompanying an application for GB type-approval in relation to a vehicle, system, component or separate technical unit, which has previously been used to apply for an EU type-approval in accordance with the EU Type Approval Regulation, may be in the same format as the information document used to apply for that EU type-approval, if the application is made—

(a) before 1st August 2026, in the case of a vehicle in category M or N, or

(b) before 1st August 2027, in the case of a vehicle in category O, a component or a separate technical unit.”;

(c) for paragraph 4, substitute—

“4.   The Secretary of State may, by regulations prescribe—

(a) the template for the information document and any other part of the information folder, and

(b) a harmonised electronic format for the purposes of paragraph 3 of this Article.”.

(5) In Article 25 (additional information to be provided with an application for EU type-approval)—

(a) in the heading, for “EU” substitute “GB”;

(b) in paragraphs 1, 2 and 3, for “EU type-approval” each time it occurs, substitute “GB type-approval”;

(c) in paragraph 1, in the second subparagraph, for “EU” substitute “GB”;

(d) in paragraph 3(b), for “EU whole-vehicle” substitute “GB whole-vehicle”.

Amendments to Chapter IV

26.—(1) In the Chapter heading for Chapter IV, for “EU” substitute “GB”.

(2) In Article 26 (General provisions on conduct of procedures for EU type-approval)—

(a) for “EU”, in the heading, and in paragraphs 1, 3 and 4, each time it occurs, substitute “GB”;

(b) in paragraph 2—

(i) in the opening words—

(aa) for “An approval” substitute “The approval”;

(bb) for “an EU” substitute “a GB”;

(ii) omit point (b);

(c) in paragraph 3, for the second subparagraph, substitute—

“The Secretary of State may by regulations amend Annexes III and IX to update the procedures in those Annexes in relation to GB type-approval and multi-stage approval to take into account regulatory and technological developments.”;

(d) in paragraph 5—

(i) for “an EU” substitute “a GB”;

(ii) omit the second sentence;

(e) in paragraph 6—

(i) for “an EU” substitute “a GB”;

(ii) omit the second subparagraph.

(3) Omit Article 27 (notifications of EU type-approval).

(4) In Article 28 (EU type-approval certificate)—

(a) for “EU”, in the heading, and in paragraphs 1, 2, 4 and 7, each time it occurs, substitute “GB”;

(b) in paragraph 2—

(i) omit “harmonised”;

(ii) omit “the identification of the Member State which granted the EU type-approval and for”;

(c) for paragraph 3, substitute—

“3.   The Secretary of State may by regulations lay down templates and provide for electronic formats for—

(a) the GB type-approval certificate;

(b) the numbering system; and

(c) the test result sheet.”;

(d) in paragraph 5—

(i) for “an EU”, substitute “a GB”;

(ii) for “EU” the second time it occurs, substitute “GB”;

(e) in paragraph 7—

(i) after “regulatory acts” insert “or regulations”;

(ii) for “the implementing acts referred to in paragraph 3” substitute “Commission Implementing Regulation (EU) 2020/683(11), or regulations made under paragraph 3 as it is now in force”.

(5) In Article 29 (specific provisions concerning EU type-approvals for systems, components and separate technical units)—

(a) in the heading, and in paragraph 3, for “EU” each time it occurs, substitute “GB”;

(b) in paragraph 1, for “An EU” substitute “A GB”.

(6) In Article 30 (tests required for EU type-approval)—

(a) for “EU” each time it occurs, including in the heading, substitute “GB”;

(b) in paragraph 1, at the end, insert “or, where paragraph 2A applies, by the technical services of an approval authority of a member State (“an EU approval authority”)”;

(c) after paragraph 2, insert—

“2A.   The approval authority may rely on tests performed by the technical services of an EU approval authority where those tests are recorded in test reports and—

(a) the test report was issued—

(i) before 31st December 2026, in the case of vehicles in category M or N, or

(ii) before 31st December 2027, in the case of vehicles in category O, components or separate technical units;

(b) the tests described in the test report were made under any regulatory act set out in the table in Part I of Annex II as those regulatory acts apply in the law of the member State concerned;

(c) the test report shows that the vehicle, component or separate technical unit meets one or more of the requirements of that regulatory act is it has effect in domestic law on the date on which the GB type-approval is issued; and

(d) the EU type-approval to which the test report relates has not been invalidated since IP completion day otherwise than in accordance with Article 35(2)(a) of the EU Type Approval Regulation as that Regulation has effect in the law of the member State concerned.

2B.   Where the EU type-approval referred to in paragraph 2A(d) has been extended or revised, the approval authority may take into account any test report or letter of no concern which accompanied any such extension or revision.”;

(d) for paragraph 3, substitute—

“3.   The Secretary of State may by regulations—

(a) amend Commission Implementing Regulation (EU) 2020/683, or

(b) make further provision on the format of the test reports.”;

(e) in paragraph 4, for “authorities” substitute “authority”;

(f) for paragraph 8, substitute—

“8.   The Secretary of State may by regulations amend Annex VIII to take account of technical and regulatory developments by updating the list of regulatory acts relating to—

(a) which virtual testing methods may be used by a manufacturer or a technical service, and

(b) the specific conditions under which those virtual testing methods are to be used.”.

(7) In Article 31 (conformity of production arrangements)—

(a) in paragraph 1—

(i) for the words from the beginning to “type-approval shall” substitute “Where the approval authority has granted a GB type-approval, it must”;

(ii) omit the words from “, if necessary” to “other Member States”;

(b) in paragraph 2, for the words from the beginning to “type-approval shall” substitute “Where the approval authority has granted a GB whole-vehicle type-approval, it must”;

(c) in paragraph 3—

(i) for the words from the beginning to “type-approval shall” substitute “Where the approval authority has granted a GB type-approval, it must”;

(ii) omit the words from “, if necessary” to “other Member States”;

(d) in paragraph 4—

(i) omit “that granted the EU type-approval”;

(ii) for “EU” substitute “GB”;

(e) in paragraph 6, for the words from the beginning to “type-approval shall” substitute “Where the approval authority has granted a GB type-approval, it must”;

(f) in paragraph 7, for the words from the beginning to “EU type-approval” substitute “Where the approval authority has granted a GB type-approval and”;

(g) for paragraph 8, substitute—

“8.   The Secretary of State may by regulations amend Annex IV to take account of technological and regulatory developments by updating the conformity of production procedures.”.

(8) Omit Article 32 (fees).

Amendments to Chapter V

27.—(1) In the heading to Chapter V, for “EU” substitute “GB”.

(2) In Article 33 (general provisions on amendments of EU type-approvals)—

(a) in the heading, and each time it occurs, for “EU type” substitute “GB type”;

(b) in paragraph 1, in the first sub-paragraph, omit “that granted the EU type-approval”;

(c) omit paragraph 2;

(d) in paragraphs 3 and 4, for “an approval” substitute “the approval”.

(3) In Article 34 (revisions and extensions of EU type-approvals)—

(a) in the heading and in paragraph 2, each time it occurs, for “EU type” substitute “GB type”;

(b) in paragraph 1, for “an approval”, substitute “the approval”.

(4) In Article 35 (termination of validity)—

(a) in paragraph 1, for “an EU” substitute “a GB”;

(b) in paragraph 2—

(i) in the opening words, for “An EU” substitute “A GB”;

(ii) in points (a), (d) and (e), for “EU type” substitute “GB type”;

(c) in paragraph 4—

(i) in the first subparagraph, omit “that granted the EU type-approval”;

(ii) omit the second subparagraph;

(d) in paragraph 5—

(i) for “an EU” substitute “a GB”;

(ii) omit “that granted the EU type-approval”;

(e) omit paragraph 6.

Amendments to Chapter VI

28.—(1) In Article 36 (certificate of conformity in paper format)—

(a) in paragraph 1—

(i) for “The”, the first time it occurs substitute “Except as permitted in paragraph 1A, the”;

(ii) for “implementing acts referred to in paragraph 4” substitute “Commission Implementing Regulation (EU) 2020/683, or regulations made under paragraph 4 as it is now in force”;

(b) after paragraph 1, insert—

“1A.   A manufacturer may use the template provided for in Commission Implementing Regulation (EU) 2020/683 as it has effect in EU law in the case of a vehicle which was manufactured before 6 July 2026 and to which a valid EU type-approval granted in accordance with the EU Type Approval Regulation also applies. A certificate of conformity so issued is to be treated as a GB certificate of conformity issued in accordance with this Article.”;

(c) in paragraph 4—

(i) in the opening words, for “The Commission shall adopt implementing acts concerning” substitute “The Secretary of State may by regulations make provision in relation to”;

(ii) omit the second subparagraph;

(d) in paragraph 5, for “at least one of the official languages of the Union” substitute “English”.

(2) In Article 37 (certificate of conformity in electronic format)—

(a) in paragraph 1—

(i) omit “that has granted the whole-vehicle type-approval”;

(ii) for “the implementing acts referred to in paragraph 8 of this Article” substitute “retained direct EU legislation made under paragraph 8 as it had effect before IP completion day, or regulations made under paragraph 8 as it is now in force”;

(b) omit paragraph 3;

(c) in paragraph 4—

(i) for “Member States” substitute “The approval authority”;

(ii) for “national small series vehicle type-approval” substitute “GB small series type-approval in accordance with Article 42”;

(d) in paragraph 5—

(i) for “The approval authority receiving” substitute “Where the approval authority receives”;

(ii) for “shall” substitute “it must”;

(iii) for “the implementing acts referred to in paragraph 8 of this Article” substitute “retained direct EU legislation made under paragraph 8 as it has effect before IP completion day or regulations made under paragraph 8 as it is now in force”;

(e) in paragraph 7—

(i) for “Member States shall” substitute “The Secretary of State must”;

(ii) for “the implementing acts referred to in paragraph 8” substitute “retained direct EU legislation made under paragraph 8 as it has effect before IP completion day or regulations made under paragraph 8 as it is now in force”;

(f) in paragraph 8—

(i) in the first subparagraph, for “Commission shall adopt implementing acts” substitute “Secretary of State may make regulations”;

(ii) omit the second subparagraph;

(g) omit paragraph 9;

(h) in paragraph 10, for “a national authority” substitute “the Secretary of State”.

(3) In Article 38 (manufacturer’s statutory and additional plates, markings and type-approval mark of components and separate technical units)—

(a) in paragraph 1, at the end, insert “or, where Article 5A applies to the vehicle, the markings required under the EU Type Approval Regulation and the relevant regulatory acts listed in Annex II to that Regulation”;

(b) for paragraph 3, substitute—

“3.   The Secretary of State may by regulations—

(a) amend Commission Implementing Regulation (EU) 2020/683, and

(b) make further provision concerning the model for the GB type-approval mark.”;

(c) in paragraph 4, at the end insert “or, where Article 5A applies to the vehicle, component or separate technical unit, with the EU Type Approval Regulation”.

Amendments to Chapter VII

29.—(1) In Article 39 (exemptions for new technologies or new concepts)—

(a) in paragraph 1, for “an EU” substitute “a GB”;

(b) in paragraph 2, for “EU-type” substitute “GB type” each time it occurs;

(c) omit paragraph 3;

(d) for paragraph 4, substitute—

“4.   If type-approval is granted under this Article, that circumstance must be reflected in the heading of—

(a) the type-approval certificate, and

(b) any certificate of conformity.

4A.   The Secretary of State may by regulations—

(a) amend Commission Implementing Regulation (EU) 2020/683, and

(b) make further provision regarding the template which is to be used for type-approval certificates and certificates of conformity for the purposes of this paragraph.”;

(e) omit paragraph 5;

(f) in paragraph 6—

(i) for “the implementing acts referred to in paragraph 3” substitute “the approval authority”;

(ii) for “authorisations are” substitute “the approval is”;

(iii) for “EU type” substitute “GB type”;

(g) omit paragraph 7.

(2) In Article 40 (subsequent adaptation of regulatory acts)—

(a) in paragraph 1—

(i) for the first subparagraph, substitute—

“1.   Where the approval authority has authorised the granting of a GB type-approval in accordance with Article 39, the Secretary of State must, where necessary, amend the regulatory acts or regulations concerned to make provision in relation to the latest technological developments.”;

(ii) in the second subparagraph, for “Commission shall” substitute “Secretary of State must”;

(b) in paragraph 2, for “in the implementing acts referred to in Article 39(3)” substitute “imposed on the type-approval under Article 39(6)”;

(c) omit paragraph 3.

Amendments to Chapter VIII

30.—(1) In Article 41 (EU type-approval of vehicles produced in small series)—

(a) in the heading—

(i) for “EU” substitute “GB”;

(ii) for “small” substitute “medium”;

(b) in paragraph 1—

(i) for “Member States” substitute “the approval authority”;

(ii) for “an EU” substitute “a GB”;

(iii) for “small” substitute “medium”;

(c) in paragraph 3—

(i) for “EU” the first time it occurs, substitute “GB”;

(ii) for “small” substitute “medium”;

(iii) omit “harmonised”;

(iv) omit the words from “the identification” to “type-approval and for”;

(d) in paragraph 4—

(i) for “Commission shall adopt implementing acts laying” substitute “Secretary of State may by regulations lay”;

(ii) for “EU” substitute “GB”;

(iii) for “small” substitute “medium”;

(iv) omit the second sentence;

(e) for paragraph 5, substitute—

“5.   The Secretary of State may by regulations amend—

(a) Appendix I of Part I to Annex II to set out the technical requirements for vehicle categories M, N and O, and

(b) point 1 of Part A of Annex V accordingly as regards the quantitative annual limits.”.

(2) In Article 42 (national type-approval of vehicles produced in small series)—

(a) in the heading, and each time it occurs, omit “national”;

(b) in paragraph 1, for “in the market of each Member State” substitute “in Great Britain”;

(c) in paragraph 2—

(i) for “Member States” the first time it occurs, substitute “The approval authority”;

(ii) for the words from “those Member States” to the end, substitute “the vehicle type satisfies the relevant alternative requirements specified in Schedule 1 to the Road Vehicles (Approval) Regulations 2020”;

(d) in paragraph 4—

(i) omit “harmonised”;

(ii) omit the words from “the identification of” to “approval and for”;

(e) for paragraph 5, substitute—

“5.   The Secretary of State may by regulations lay down the template and numbering system for the type-approval certificate of vehicles produced in small series which must bear the heading “GB small series vehicle type-approval certificate” and must bear the content and nature of the exemptions granted pursuant to paragraph 2 of this Article.”.

(3) Omit Article 43 (validity of a national type-approval of vehicles produced in small series).

Amendment to Chapter IX

31.—(1) Omit Article 44 (EU individual vehicle approvals).

(2) In Article 45 (national individual vehicle approvals)—

(a) in the heading and each time it occurs, omit “national”;

(b) in paragraph 1—

(i) for “Member States” the first time it occurs, substitute “The approval authority”;

(ii) for “those Member States have imposed relevant alternative requirements” substitute “the vehicle complies with the relevant alternative requirements specified in Schedule 2 to the Road Vehicles (Approval) Regulations 2020”;

(c) in paragraph 3, for “Member States shall” substitute “The approval authority must”;

(d) in paragraph 5, for “A Member State shall” substitute “The approval authority must”;

(e) in paragraph 6, for the words “shall at least” to the end, substitute “must allow for the identification of the requirements with which the vehicle conforms”;

(f) for paragraph 7, substitute—

“7.   The Secretary of State may by regulations lay down the template and the numbering system to be used in the GB individual vehicle approval certificate.”.

(3) Omit Article 46 (validity of national individual vehicle approvals).

(4) In Article 47 (specific provisions), in paragraphs 1 and 2, for “Articles 44 and 45” substitute “Article 45”.

Amendments to Chapter X

32.—(1) In Article 48 (making available on the market, registration or entry into service: vehicles other than end-of-series vehicles)—

(a) in paragraph 1, at the end, insert “or, where Article 5A applies to the vehicle, Articles 36 and 37 of the EU Type Approval Regulation.”;

(b) in paragraph 2, after “produced in” insert “medium and”.

(2) In Article 49 (making available on the market, registration or entry into service: end-of-series vehicles)—

(a) in paragraph 1—

(i) for “Member States” substitute “the Secretary of State”;

(ii) for “EU” each time it occurs, substitute “GB”;

(iii) for “Union” substitute “United Kingdom”;

(b) in paragraph 2, for “EU” substitute “GB”;

(c) in paragraph 3—

(i) in the first subparagraph, for the words from “competent authority” to “in question” substitute “approval authority”;

(ii) in the second subparagraph—

(aa) for “Member States concerned” substitute “approval authority”;

(bb) omit “within their territory”;

(d) in paragraph 4, for “Member States shall” substitute “The Secretary of State must”;

(e) at the end, insert—

“5.   A request may be made under paragraph 3 in relation to—

(a) motor vehicles in relation to which the manufacturer holds a relevant EU approval which is no longer valid under the EU Type Approval Regulation and that—

(i) were in the United Kingdom before IP completion date, or

(ii) are qualifying Northern Ireland goods,

(b) trailers in relation to which the manufacturer holds a relevant EU approval which is no longer valid under the EU Type Approval Regulation and that—

(i) were in the United Kingdom before 1st January 2023, or

(ii) are qualifying Northern Ireland goods, and

(c) motor vehicles or trailers in relation to which the manufacturer holds a relevant NI type-approval which is no longer valid under the EU Type Approval Regulation.

6.   In paragraph 5, “relevant EU approval” and “relevant NI approval” have the meanings given in Article 5A.

7.   Where a request made under paragraph 3 includes any vehicle or trailer referred to in paragraph 5, references in paragraphs 1 and 2 to “GB type-approval” include a reference to “EU type-approval in accordance with the EU Type Approval Regulation”.”.

(3) In Article 50 (making available on the market or entry into service: components and separate technical units)—

(a) in paragraph 1, for “Components” substitute “Subject to paragraph 1A, components”;

(b) after paragraph 1, substitute—

“1A.   Components and separate technical units to which Article 5A applies, including those intended for the aftermarket, may also be made available on the market or entered into service provided that they comply with the requirements of the relevant regulatory acts listed in Annex II of the EU Type Approval Regulation and are properly marked in accordance with Article 38 of that Regulation.”;

(c) in paragraph 3—

(i) for “Member States may permit” substitute “Paragraph 1 does not apply to”;

(ii) omit “44”;

(iii) after “45” insert “or, where Article 5A applies to the vehicle, Articles 41, 42, 44 and 45 of the EU Type Approval Regulation”;

(d) in paragraphs 4 and 5, for “Member States may also permit” substitute “Paragraph 1 does not apply to”;

(e) after paragraph 5, insert—

“6.   Notwithstanding paragraph 1, replacement components and separate technical units that were EU type-approved before 1st January 2023 in accordance with the regulatory acts listed in Annex II of the EU Type Approval Regulation may be made available on the market or entered into service.”.

Amendments to Chapter XI

33.—(1) In Article 51 (national evaluation for serious risk or non-compliance)—

(a) in the heading, omit “national”;

(b) in the first paragraph—

(i) for “an approval” substitute “the approval”;

(ii) for “authorities of one Member State have” substitute “authority has”;

(iii) after “this Regulation”, the second time it occurs, insert “or, where Article 5A applies to the vehicle, system, component or separate technical unit, the EU Type Approval Regulation”;

(iv) after “this Regulation” the third time it occurs, insert “or, where applicable, the EU Type Approval Regulation”;

(v) omit “and the relevant approval authorities”;

(vi) for “surveillance authorities,”, substitute “surveillance authority,”.

(2) In Article 52 (national procedures for serious risk or non-compliance)—

(a) in the heading, omit “national”;

(b) in paragraph 1, omit “of one Member State”;

(c) in paragraph 2—

(i) omit “of one Member State”;

(ii) after “this Regulation” insert “or, where Article 5A applies to the vehicle, system, component or separate technical unit, the EU Type Approval Regulation”;

(iii) omit “in the Union”;

(d) in paragraph 3—

(i) for “national authorities” substitute “market surveillance authority”;

(ii) omit “on their national market”;

(iii) for “that market” substitute “the market”;

(e) omit paragraph 4.

(3) In Article 53 (corrective and restrictive measures at Union level)—

(a) in the heading, omit “at Union level”;

(b) omit paragraphs 1 to 7;

(c) for paragraph 8, substitute—

“8.   Where a corrective measure is imposed in accordance with Article 52, that measure must be available free of charge to holders of registrations for the affected vehicles. Where repairs have been carried out at the registration holder’s expense before the adoption of the corrective measure, the manufacturer must reimburse the cost of such repairs up to the cost of the repairs required by that corrective measure.”.

(4) Omit Article 54 (non-compliant EU type-approval).

(5) In Article 55 (placing on the market and entry into service: parts or equipment that may pose a serious risk to the correct functioning of essential systems)—

(a) in paragraph 1, for “an approval” substitute “the approval”;

(b) in paragraph 3, for the first sub-paragraph, substitute—

“3.   The Secretary of State may by regulations lay down the requirements for the authorisation of the parts and equipment referred to in paragraph 1 of this Article.”;

(c) in paragraph 4, in the opening words, for “The Commission is empowered to adopt delegated acts in accordance with Article 82, amending”, substitute “The Secretary of State may by regulations amend”;

(d) in paragraph 6—

(i) for “the Commission” the first time it occurs, substitute “the approval authority”;

(ii) for the third sentence, substitute “The Secretary of State may by regulations set out when those authorisations may be granted”;

(iii) omit the fourth sentence.

(6) In Article 56 (related requirements for parts or equipment that may pose a serious risk to the correct functioning of essential systems)—

(a) in paragraph 1, in the second sentence, omit “and to one approval authority only”;

(b) in paragraph 2, for the fourth subparagraph, substitute—

“The Secretary of State may by regulations lay down the template and the numbering system for the authorisation certificate referred to in the third subparagraph of this paragraph.”;

(c) in paragraph 3, in the first paragraph—

(i) in the first sentence, omit “that issued the authorisation”;

(ii) in the second sentence, for “That approval” substitute “The approval”;

(d) omit paragraphs 5, 6 and 7.

Amendment to Chapter XII

34.—(1) In Article 57 (UN regulations required for EU type-approval)—

(a) in the heading, for “EU” substitute “GB”;

(b) in paragraph 1—

(i) for “Union” both times it occurs, substitute “United Kingdom”;

(ii) for “EU” substitute “GB”;

(c) in paragraph 2—

(i) in the first subparagraph—

(aa) for “Union” substitute “United Kingdom”;

(bb) for “Commission shall adopt delegated acts in accordance with Article 82, supplementing” substitute “the Secretary of State may by regulations supplement”;

(ii) in the second subparagraph—

(aa) for “Those delegated acts shall” substitute “Regulations made under this paragraph must”;

(bb) for “EU” substitute “GB”.

(2) In Article 58 (equivalent of UN Regulations for the purpose of EU type-approval)—

(a) in the heading, for “EU” substitute “GB”;

(b) in paragraph 2, for “authorities of the Member States” substitute “authority”.

Amendment to Chapter XIII

35.—(1) In Article 59 (information intended for users), in paragraph 3, for the words from “the official language” to “into service” substitute “English”.

(2) In Article 60 (information intended for manufacturers), in paragraph 1, for “EU” substitute “GB”.

Amendments to Chapter XIV

36.—(1) In Article 61 (manufacturers’ obligations to provide vehicle OBD information and vehicle repair and maintenance information)—

(a) in paragraph 2, for the words from the beginning to “standardisation body” substitute “The Secretary of State may by regulations specify a relevant standard for the purposes of this Article, from standards developed by the British Standards Institute, the European Committee for Standardisation or a comparable standardisation body. Until such a standard has been specified”;

(b) in paragraph 3(a), omit “national”;

(c) in paragraph 11—

(i) for the words from the beginning to “amending” substitute “The Secretary of State may by regulations amend”;

(ii) for “Commission shall” substitute “Secretary of State must”.

(2) In Article 63 (fees for access to vehicle repair and maintenance information), in paragraph 1—

(a) for “national authorities” substitute “the approval authority or the market surveillance authority”;

(b) for “the Commission and” substitute “and to”.

(3) In Article 64 (proof of compliance with vehicle OBD information and repair and maintenance information obligations), in paragraph 1, for “EU type-approval or national type-approval” substitute “a GB type-approval, including a GB small series type-approval”.

(4) In Article 65 (compliance with obligations regarding access to vehicle OBD information and vehicle repair and maintenance information)—

(a) in paragraph 1, for “An approval” substitute “The approval”;

(b) in paragraph 2—

(i) for “an approval” substitute “the approval”;

(ii) omit “that granted the relevant type-approval”;

(c) in paragraph 3—

(i) omit “request the approval authority that granted the whole vehicle type-approval to”;

(ii) for “subsequently to” substitute “subsequently”;

(iii) omit “the national approval authority and”;

(iv) omit “of the request”.

(5) Omit Article 66 (forum on access to vehicle information).

Amendments to Chapter XV

37.—(1) In Article 67 (type-approval authority responsible for technical services)—

(a) in paragraph 1—

(i) omit the words from “designated by” to “(‘type-approval authority’)”;

(ii) for “type-approval” the second time it occurs, substitute “approval”;

(b) omit paragraphs 2 and 3;

(c) in paragraph 4, for “type-approval” substitute “approval”;

(d) omit paragraphs 5 to 10.

(2) In Article 68 (designation of technical services)—

(a) in paragraph 1, in the opening words, for “type-approval authorities shall” substitute “approval authority must”;

(b) in paragraph 2, for “Each Member State may designate a type-approval authority” substitute “The approval authority may designate itself”;

(c) in paragraph 3—

(i) after “law of” insert “the United Kingdom or any part of the United Kingdom or of”;

(ii) for “type-approval” substitute “approval”;

(d) in paragraph 4—

(i) for “unless such liability is assumed by its Member State in accordance with national law”, substitute “unless a state has assumed liability for those activities in accordance with its national law”;

(ii) for “Member State” the second time it occurs, substitute “Secretary of State”;

(e) omit paragraph 5.

(3) In Article 69 (independence of technical services)—

(a) in paragraph 2, in the second subparagraph, for “type-approval authority of the relevant Member State”, substitute “approval authority”;

(b) in paragraph 5—

(i) for “type-approval” substitute “approval”;

(ii) omit “Union or national”.

(4) In Article 70 (competence of technical services)—

(a) in paragraph 1, in the opening words, for “type-approval” substitute “approval”;

(b) in paragraph 3, for the words from “The Commission” to “amending”, substitute “The Secretary of State may by regulations amend”.

(5) In Article 71 (subsidiaries of and subcontracting by technical services)—

(a) for “type-approval” each time it occurs, substitute “approval”;

(b) in paragraph 4, omit “designating”.

(6) In Article 72 (in-house technical service of the manufacturer), in paragraph 3, for the words from “The Commission” to “amending”, substitute “The Secretary of State may by regulations amend”.

(7) In Article 73 (assessment and designation of technical services)—

(a) in paragraph 1—

(i) for “type-approval” substitute “approval”;

(ii) omit “of the Member State in which it requests to be designated”;

(b) in paragraph 2—

(i) for “a type-approval” substitute “the approval”;

(ii) for “the type-approval” substitute “the approval”;

(iii) for “Union” substitute “United Kingdom”;

(c) in paragraph 3, for “type-approval” substitute “approval”;

(d) omit paragraphs 4 to 7;

(e) in paragraph 8, for “The joint assessment team shall” substitute “The personnel of the approval authority carrying out an assessment must”;

(f) omit paragraphs 10 to 14;

(g) in paragraph 16—

(i) for “The type-approval authority that”, substitute “Where the approval authority”;

(ii) for “shall” substitute “it must”.

(8) Omit Article 74 (notification to the Commission concerning designation of technical services).

(9) In Article 75 (changes to and renewal of designations of technical services)—

(a) in paragraph 1—

(i) in the first subparagraph, for “type-approval”, both times it occurs, substitute “approval”;

(ii) omit the second and third subparagraphs;

(b) in paragraph 2—

(i) for “type-approval” substitute “approval”;

(ii) omit “approval authorities or for the”;

(iii) for “authorities” the second time it occurs, substitute “authority”;

(c) in paragraph 3—

(i) in the first subparagraph—

(aa) for “type-approval”, the first time it occurs, substitute “approval”;

(bb) for “the notification referred to in the second subparagraph of” substitute “restricting, suspending or withdrawing the designation under”;

(cc) for “EU” substitute “GB”;

(dd) for “the technical service” the second time it occurs, substitute “that technical service”;

(ee) omit the words from “subject of the change” to the end;

(ii) in the second subparagraph—

(aa) for “notified the changes to” substitute “restricted, suspended or withdrawn”;

(bb) for “type-approval”, the first time it occurs, substitute “approval”;

(cc) for “submit” substitute “prepare”;

(dd) omit the words “to the Commission and the other type-approval authorities”;

(ee) omit “designating type-”;

(ff) omit “instruct the type-approval authorities concerned to”;

(gg) for “EU” substitute “GB”;

(d) for paragraph 4, substitute—

“4.   Where the designation of a technical service has been restricted, suspended or withdrawn, but the approval authority has decided not to suspend or withdraw, in accordance with the second subparagraph of paragraph 3, the GB type-approval certificates which were issued on the basis of inspection and test reports issued by that technical service, those certificates remain valid unless the type-approvals have been invalidated in accordance with point (f) of Article 35(2).”;

(e) in paragraph 5, in the second paragraph, omit “, and subject to the notification in Article 74”;

(f) in paragraph 6, for “type-approval” substitute “approval”.

(10) In Article 76 (monitoring technical services)—

(a) in paragraph 1, omit “designating type-” each time it occurs;

(b) in paragraph 2—

(i) for “a type-approval” substitute “the approval”;

(ii) omit “or by the Commission”;

(c) in paragraph 3—

(i) in the first subparagraph, omit “designating type-”;

(ii) omit the second, third and fourth subparagraphs;

(d) in paragraph 4—

(i) in the first paragraph, for “designating type-approval authority” substitute “approval authority”;

(ii) omit the second subparagraph.

(11) Omit Articles 77 (challenge to competence of technical services) and 78 (exchange of information on assessment, designation and monitoring of technical services).

(12) In Article 79 (cooperation with national accreditation bodies)—

(a) in paragraph 1, for “type-approval” substitute “approval”;

(b) in paragraph 2—

(i) for the words from the beginning to “keeps” substitute “The approval authority must keep”;

(ii) for “type-approval” the second time it occurs, substitute “approval”;

(iii) omit the words from “of the Member State” to “established”.

(13) In Article 80 (operational obligations of technical services)—

(a) in paragraph 2, for “designating type-approval”, both times it occurs substitute “approval”;

(b) in paragraph 3, for “type-approval”, each time it occurs, substitute “approval”.

(14) In Article 81 (information obligations of technical services), omit “designating type-” both times it occurs.

Amendment to Chapter XVI

38.—(1) For Article 82 (exercise of the delegation), substitute—

“Article 82 Regulations

1.   Any power to make regulations conferred on the Secretary of State by this Regulation is exercisable by statutory instrument.

2.   Such regulations may—

(a) make incidental, supplemental, consequential or transitional provision, and

(b) make different provision for different cases or descriptions of case, different circumstances, different purposes or different areas.

3.   Before making any regulations to which paragraph 4 applies the Secretary of State must consult with such representative organisations as the Secretary of State thinks fit.

4.   This paragraph applies to regulations made under Articles 4(2), 5(3), 26(3), 30(8), 31(8), 41(5), 55(3) or (4), 61(11), 70(3), 72(3) or Annex X.

5.   A statutory instrument containing regulations made under this Regulation is subject to annulment in pursuance of a resolution of either House of Parliament.”.

(2) Omit Article 83 (committee procedure).

Amendments to Chapter XVII

39.  Omit Articles 84 (penalties), 85 (administrative fines in support of corrective and restrictive measures at Union level) and 90 (reporting).

Amendments to Annex I

40.—(1) Annex I (general definitions, criteria for vehicle categorisation, types of vehicle and types of bodywork) is amended as follows.

(2) In the Introductory Part, in paragraph 2.4.1, for “Council Directive 80/181/EEC” substitute “the Units of Measurement Regulations 1986(12).

(3) In Part A (criteria for vehicle categorisation)—

(a) in paragraph 1, in the first subparagraph, for the words from the beginning to “national individual vehicle approval” substitute “For the purposes of GB type-approval, including GB small series type-approval, and individual vehicle approval”;

(b) in paragraph 6.2, omit “national”.

(4) In Part B (criteria for types of vehicle, variants and versions), in paragraph 6.3.1(b), for “points 3.2 and 3.3 of Annex 1 to Directive 96/53/EC”, substitute “column 4 of table 6 in Schedule 3 to the Road Vehicles (Authorised Weight) Regulations 1998(13)”.

Amendments to Annex II

41.—(1) Annex II (requirements for the purpose of EU type-approval of vehicles, systems, components or separate technical units) is amended as follows.

(2) In the heading to Annex II, and in the heading to Part I (regulatory acts for EU type-approval of vehicles produced in unlimited series) of Annex II, for “EU” substitute “GB”.

(3) In Part I of Annex II, in Appendix 1—

(a) in the heading to Appendix 1—

(i) for “EU” substitute “GB”;

(ii) for “small” substitute “medium”;

(b) in table 1—

(i) in item 20A, in the column headed “applicability and specific requirements”—

(aa) before “Daytime Running Lights (DRL)”, insert “The requirement for”;

(bb) for the words “shall be fitted” to the end, substitute “does not apply to types which had EU whole-vehicle type-approval prior to 1st February 2026, in accordance with this Regulation or the EU Type Approval Regulation.”;

(ii) in item 63, in the column headed “applicability and specific requirements”, for “EU” substitute “GB”;

(c) in table 2—

(i) in footnote (¹), for “EU” substitute “GB”;

(ii) in item 20A, in the column headed “applicability and specific requirements”—

(aa) before “Daytime Running Lights (DRL)”, insert “The requirement for”;

(bb) for the words “shall be fitted” to the end, substitute “does not apply to types which had EU whole-vehicle type-approval prior to 1st February 2026, in accordance with this Regulation or the EU Type Approval Regulation.”;

(iii) in item 63, in the column headed “applicability and specific requirements”, for “EU” substitute “GB”.

(4) Omit Appendix 2 to Part I.

(5) In Part II (list of UN regulations recognised as an alternative to the Directives or Regulations referred to in Part I) to Annex II—

(a) in the opening paragraph—

(i) for “Union” substitute “United Kingdom”;

(ii) omit “by virtue of Decision 97/836/EC, or subsequent Council decisions as referred to in Article 3(3) of that Decision,”;

(iii) for “an EU” substitute “a GB”;

(b) in the second paragraph—

(i) for “an EU” substitute “a GB”;

(ii) omit “, subject to the Community Decision as referred to in Article 4(2) of Decision 97/836/EC”.

(6) In Part III (list of regulatory acts setting out the requirements for the purpose of EU type-approval of special purpose vehicles) to Annex II—

(a) in the heading, for “EU” substitute “GB”;

(b) in the explanatory notes following the table in Appendix 6—

(i) in note X, for “Member States” substitute “The approval authority”;

(ii) in note Q, for “An EU” substitute “A GB”;

(iii) in note R, for the existing text, substitute “Space must be provided for a registration plate meeting the requirements of the Road Vehicles (Display of Registration Marks) Regulations 2001(14)”;

(iv) in note T, for “The vehicle can be tested in accordance with Directive 70/157/EEC” substitute “The vehicle may be subjected to the test procedures described in Directive 70/157/EEC, as it had effect immediately before IP completion day”;

(v) in notes V and V1, for “Directive 97/68/EC” substitute “Regulation (EU) 2016/1628(15)”;

(vi) in note W1, in the second subparagraph, for “An EU” substitute “A GB”;

(vii) in note W6, for the third sentence of the second subparagraph, substitute “An extension to the UNECE type-approval (or GB type-approval, if applicable) is not required.”;

(viii) in note W8, in the second subparagraph, for “EU” substitute “GB”.

Amendments to Annex III

42.—(1) Annex III (procedures to be followed with respect to EU type-approval) is amended as follows.

(2) In the heading to Annex III, for “EU” substitute “GB”.

(3) In paragraph 2, in points (a), (b) and (d), for “EU” substitute “GB”.

Amendments to Annex IV

43.—(1) Annex IV (conformity of production procedures) is amended as follows.

(2) In point 2.3.1.1(c), omit “in one of the Member States”.

(3) Omit point 2.3.2.

(4) In point 4.1.1.2, omit the last sentence.

Amendments to Annex V

44.—(1) Annex V (small series and end-of-series limits) is amended as follows.

(2) For the heading, substitute “GB medium series, GB small series and end-of-series limits”.

(3) In section A (small series quantitative annual limits)—

(a) in the heading, after “small” insert “and medium”;

(b) in paragraph 1, for “in the Union” substitute “in Great Britain”;

(c) in the table following paragraph 1, in the entry for “N2, N3”, for “delegated acts” substitute “regulations”;

(d) in paragraph 2, for “in a Member State, shall be determined by that Member State but”, substitute “in Great Britain”.

(4) In section B (end-of-series limits)—

(a) in the opening words—

(i) for “in each Member State”, substitute “in Great Britain”;

(ii) for “the Member State” substitute “the Secretary of State”;

(b) in paragraph 1—

(i) for “in that Member State”, substitute “in Great Britain”;

(ii) for “the Member State” substitute “the Secretary of State”.

Amendments to Annex VII

45.—(1) Annex VII (regulatory acts for which a manufacturer may be designated as a technical service) is amended as follows.

(2) In point 1.3—

(a) for “EU” substitute “GB”;

(b) for “small” substitute “medium”.

(3) In paragraph 3 of the Appendix to Annex VII, for “implementing acts referred to in Article 30(3)” substitute “retained direct EU legislation made under Article 30(3) as it had effect before IP completion day, or regulations made under Article 30(3) as it is now in force”.

Amendments to Annex VIII

46.  In Appendix 3 to Annex VIII (conditions for the use of virtual testing methods by a manufacturer or a technical service), for the flow chart, substitute—

   

“

”

Amendments to Annex IX

47.—(1) Annex IX (procedures to be followed during multi-stage type-approval) is amended as follows.

(2) In point 1.1, in the second sentence, for “approval authorities” substitute “the approval authority”.

(3) In the heading at point 2, for “approval authorities” substitute “the approval authority”.

(4) In point 2.1, in subparagraphs (a) and (c), for “EU” substitute “GB”.

(5) In point 2.2, for “EU” substitute “GB”.

(6) In point 3.2.4, for “EU” substitute “GB”.

(7) In point 4.2, in the second indent, for “EU” substitute “GB”.

(8) In the Appendix, for “e2*201X/XX*2609” substitute “g11*201X/XX*2609”.

Amendments to Annex X

48.—(1) Annex X (access to vehicle OBD information and vehicle repair and maintenance information) is amended as follows.

(2) In point 2.2, for “An approval authority” substitute “The approval authority”.

(3) Omit point 5.3.

(4) In point 6.3, for the words from “Forum” to “Article 66 shall” substitute “Secretary of State must by regulations”.

(5) In point 6.6, for “Regulation (EC) No 692/2008” substitute “Commission Regulation (EU) 2017/1151(16)”.

CHAPTER 2 Other EU Regulations

Regulation (EC) No 715/2007

49.—(1) Regulation (EC) No 715/2007 is amended as follows.

(2) In Article 2 (scope), for “Annex II to Directive 70/156/EEC” both times it occurs, substitute “Article 4 of Regulation (EU) 2018/858(17)”.

(3) In Article 3 (definitions), in paragraphs 2 and 13, for “Directive 70/156/EEC” each time it occurs, substitute “Regulation (EU) 2018/858”.

(4) In Article 4 (manufacturer’s obligations)—

(a) in paragraph 1, for “the Community” both times it occurs, substitute “Great Britain”;

(b) in paragraph 2, in the third sub-paragraph, omit the final sentence;

(c) for paragraph 4, substitute—

“4.   The Secretary of State may by regulations establish procedures and requirements for the implementation of paragraphs 2 and 3.”.

(5) In Article 5(3) (requirements and tests), for the opening words, substitute “The Secretary of State may by regulations impose requirements for the implementation of paragraph 2, which must include establishing the requirements relating to”.

(6) In the heading to Chapter IV (obligations of member States), for “Member States” substitute “the Secretary of State”.

(7) In Article 10 (type approval)—

(a) for “EC type approval or national type approval”, each time it occurs, substitute “GB type-approval”;

(b) in paragraph 1, for “national authorities” substitute “Secretary of State”;

(c) in paragraphs 2 and 4, for “national authorities”, substitute “approval authority”;

(d) in paragraphs 3 and 5—

(i) for “Article 7(1) of Directive 70/156/EEC” substitute “Article 48 of Regulation (EU) 2018/858”;

(ii) for “national authorities” substitute “the Secretary of State”;

(e) in paragraph 6, for “the Community” substitute “Great Britain”.

(8) In Article 11 (type approval of replacement parts)—

(a) for “national authorities” each time it occurs, substitute “the approval authority”;

(b) in paragraph 2, for “EC” substitute “GB”.

(9) Omit Articles 12 (financial incentives) and 13 (penalties).

(10) In Article 14 (redefinition of specifications)—

(a) in paragraph 1—

(i) in the first sentence, for “Commission” substitute “Secretary of State”;

(ii) for the second sentence, substitute “The Secretary of State may make regulations to account for, or limit, methane emissions.”;

(b) omit paragraphs 2 and 3;

(c) in paragraph 4—

(i) in the first sentence, for “Commission” substitute “Secretary of State”;

(ii) for the second sentence, substitute “If the Secretary of State considers that it is necessary to regulate the emissions of additional pollutants, the Secretary of State may make regulations amending these Regulations accordingly.”;

(d) in paragraph 5—

(i) for “Commission” substitute “Secretary of State”;

(ii) for the words from “shall present” to the end, substitute “may make regulations if the Secretary of State considers that it is appropriate to do so to tighten the emission limits”.

(11) For Article 15 (committee procedure), substitute—

“Article 15 Regulations

1.   Any power to make regulations conferred on the Secretary of State by this Regulation is exercisable by statutory instrument.

2.   Such regulations may—

(a) make incidental, supplemental, consequential or transitional provision, and

(b) make different provision for different cases or descriptions of case, different circumstances, different purposes or different areas.

3.   Regulations to which paragraph 4 applies may not be made unless the Secretary of State has consulted with such representative organisations as they think fit.

4.   This paragraph applies to regulations made under Article 4(4), 5(3) or 14.

5.   A statutory instrument containing regulations under Article 14 may not be made unless a draft of the instrument containing them has been laid before Parliament and approved by a resolution of each House.

6.   A statutory instrument containing regulations made under any other provision of this Regulation is subject to annulment in pursuance of a resolution of either House of Parliament.”.

(12) Omit Article 16 (amendments to Directives 70/156/EC and 2005/55/EC) and Annex II.

(13) In Article 18, omit paragraph 3.

(14) After Article 18 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”

Regulation (EC) No 78/2009: Amendments to Articles

50.—(1) Regulation (EC) No 78/2009 is amended as follows.

(2) In Article 2(1) (scope), for “Article 3(11) of Directive 2007/46/EC and in point 1 of Section A of Annex II thereto”, both times it occurs, substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 3(5) (definitions) for “Directive 2007/46/EC” substitute “Commission Implementing Regulation (EU) 2020/683(18)”.

(4) In Article 4 (technical requirements)—

(a) in paragraphs 3 and 4, for “approval authorities” substitute “approval authority”;

(b) for paragraph 6, substitute—

“6.   The Secretary of State may by regulations lay down technical provisions for the application of the requirements set out in Annex I.”.

(5) In Article 5 (application for EC type-approval), in the heading and each other time it occurs, for “EC”, substitute “GB”.

(6) In the heading of Chapter III (obligations of the authorities of member States), for “the authorities of member States” substitute “the Secretary of State and the approval authority”.

(7) In Article 6 (granting of EC type-approval)—

(a) in the heading and each time it occurs, for “EC” substitute “GB”;

(b) in paragraph 1, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(c) in paragraph 3, for “An approval” substitute “The approval”.

(8) In Article 7 (EC type-approval mark)—

(a) in the heading, for “EC” substitute “GB”;

(b) in the Article, for “an EC” substitute “a GB”.

(9) In Article 8 (modification of the type and amendments to approvals), for “Article 13 of Directive 2007/46/EC” substitute “Article 33 of Regulation (EU) 2018/858”.

(10) In Article 9 (timetable for application to vehicles)—

(a) for “EC type-approval” each time it appears, substitute “GB type-approval”;

(b) in paragraph 1—

(i) for “national authorities” substitute “the approval authority”;

(ii) omit “or national type-approval”;

(c) in paragraph 2—

(i) for “national authorities” substitute “the Secretary of State”;

(ii) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(d) in paragraph 3—

(i) for “national authorities” substitute “the approval authority”;

(ii) omit “or national type-approval”;

(e) omit paragraph 4;

(f) in paragraph 5—

(i) for “national authorities” substitute “the approval authority”;

(ii) omit “or national type-approval”;

(g) in paragraphs 6, 7 and 8—

(i) for “national authorities” substitute “the Secretary of State”;

(ii) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(h) in paragraph 9—

(i) for “national authorities” substitute “the approval authority”;

(ii) omit “or national type-approval”.

(11) In Article 10 (application to frontal protection systems)—

(a) in paragraph 1—

(i) for “National authorities” substitute “The approval authority”;

(ii) for “EC” both times it occurs, substitute “GB”;

(iii) omit “or national type-approval”;

(b) in paragraph 2—

(i) for “National authorities” substitute “The Secretary of State”;

(ii) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(c) in paragraph 3, for “Article 28 of Directive 2007/46/EC” substitute “Article 50 of Regulation (EU) 2018/858”.

(12) Omit Articles 11 (collision avoidance systems) to 14 (amendments to Directive 2007/46/EC).

(13) After Article 16 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States”.

Regulation (EC) No 78/2009: Annexes

51.—(1) The Annexes to Regulation (EC) No 78/2009 are amended as follows.

(2) In the list of Annexes, for “EC” each time it occurs, substitute “GB”.

(3) In Annex I (technical provisions for the testing of vehicles and frontal protection systems), in paragraph 1.8, for the definition of “windscreen” substitute “‘windscreen’ means the frontal glazing of the vehicle situated between the A-pillars;”.

(4) In Annex II (model information documents to be supplied by the manufacturer)—

(a) in the list of Parts after the heading to Annex II, for “EC” each time it occurs, substitute “GB”;

(b) in Part 1, in the heading, for “EC” substitute “GB”;

(c) in Parts 2 and 3, for “EC type-approval” each time it occurs, substitute “GB type-approval”.

(5) In the notes following Part 3 of Annex II, in note (c), for the words “Section A of Annex II” to the end, substitute “Article 4 of Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles(19).”.

(6) In Annex III (EC type-approval model certificates)—

(a) for “EC type-approval” each time it occurs, including in the heading, in the Appendix and the Addenda to Parts 1, 2 and 3, substitute “GB type-approval”;

(b) in Parts 1, 2 and 3, in each case in the words before section 1, for “as implemented by …” substitute “as it has effect in domestic law, as last amended by S.I. …./….”;

(c) in Parts 1 and 2, in note 4 to point 0.4, in each case for the words “Section A of Annex II” to the end, substitute “Article 4 of Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.”;

(d) in Part 3—

(i) at the end of the heading, insert “(SEPARATE TECHNICAL UNIT)”;

(ii) in paragraph 0.7 of Section 1, for “EC” substitute “GB”;

(iii) in paragraph 1.5.1 of Section II, in note (c) after the table, for “[implementing legislation]” substitute “Regulation (EU) 631/2020(20)”;

(e) in the notes to the Addendum to Part 1, in note 3, for “Commission [implementing legislation]” substitute “Commission Regulation (EU) 631/2010”.

(7) In Annex IV (EC type-approval mark)—

(a) in the heading, and each other time it occurs, including in the Appendix, for “EC type-approval” substitute “GB type-approval”;

(b) in point 1.1, for the words “‘e’” to the end of the point, substitute “‘g’ followed by the number 11.”;

(c) in point 1.2, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Regulation (EU) 2020/683”;

(d) in the Appendix—

(i) for the image, substitute—

“

”

(ii) in the note after the image, omit “in Germany (e1)”.

Regulation (EC) No 79/2009

52.—(1) Regulation (EC) No 79/2009 is amended as follows.

(2) In Article 2(1) (scope), for “Section A of Annex II to Directive 2007/46/EC”, substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 4 (obligations of manufacturers)—

(a) in paragraph (1)—

(i) for “within the Community”, both times it occurs, substitute “with Great Britain”;

(ii) for “and its implementing measures” substitute “and Commission Regulation (EU) No 406/2010(21)”;

(b) in paragraphs (2) and (3), for “and its implementing measures” substitute “and Commission Regulation (EU) 406/2010”;

(c) in paragraph (4), for “authorities” substitute “authority”.

(4) In Article 11 (timetable for application)—

(a) in paragraph 1—

(i) for “national authorities” substitute “the approval authority”;

(ii) for “EC type-approval”, both times it occurs, substitute “GB type-approval”;

(iii) for “its implementing measures”, both times it occurs, substitute “Commission Regulation (EU) No 406/2010”;

(iv) in subparagraph (a), omit “or national type-approval”;

(b) in paragraph 2—

(i) for “national authorities”, substitute “the Secretary of State”;

(ii) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(iii) for “its implementing measures”, both times it occurs, substitute “Commission Regulation (EU) No 406/2010”;

(c) in paragraph 3—

(i) for “national authorities” substitute “the Secretary of State”;

(ii) for “EC type-approval” both times it occurs, substitute “GB type-approval”;

(iii) for “its implementing measures”, both times it occurs, substitute “Commission Regulation (EU) No 406/2010”;

(iv) in subparagraph (a), omit “or national type-approval”.

(5) In Article 12 (delegated powers)—

(a) in the opening words, for “The Commission is empowered to adopt delegated acts in accordance with Article 12a in order to” substitute “The Secretary of State may by regulations”;

(b) in point (e), omit “EC”.

(6) For Article 12a (exercise of the delegation), substitute—

“Article 12a Regulations

1.   Any power to make regulations conferred on the Secretary of State by this Regulation is exercisable by statutory instrument.

2.   Such regulations may—

(a) make incidental, supplemental, consequential or transitional provision, and

(b) make different provision for different cases or descriptions of case, different circumstances, different purposes or different areas.

3.   Regulations to which paragraph 4 applies may not be made unless the Secretary of State has consulted with such representative organisations as the Secretary of State thinks fit.

4.   This paragraph applies to regulations made under Article 12, except those made under paragraphs (a), (b) and (f) of that Article.

5.   A statutory instrument containing regulations made under this Article is subject to annulment in pursuance of a resolution of either House of Parliament.”.

(7) Omit Article 15 (penalties for non-compliance).

(8) After Article 16 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.

Regulation (EC) No 595/2009

53.—(1) Regulation (EC) No 595/2009 is amended as follows.

(2) In Article 2 (scope), in the first subparagraph, for “Annex II of Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 3 (definitions)—

(a) in the first subparagraph, in points 1 and 10, for “point 25 of Article 3 of Directive 2007/46/EC”, substitute “point 20 of Article 3 of Regulation (EU) 2018/858”;

(b) in the second subparagraph—

(i) for “The Commission may” substitute “the Secretary of State may by regulations”;

(ii) omit the second sentence.

(4) In Article 4 (obligations of the manufacturers)—

(a) in paragraph 1, for “the Community” each time it occurs, substitute “Great Britain”;

(b) in paragraph 3—

(i) for “The Commission shall” substitute “The Secretary of State must, by regulations,”;

(ii) omit the second sentence.

(5) In Article 5(4) (requirements and tests)—

(a) for the opening words, substitute “The Secretary of State may make regulations to implement this Article, including regulations in relation to the following”;

(b) omit the second subparagraph.

(6) In Article 5b (specific requirements for Member States re the environmental performance of certain categories of vehicles)—

(a) in the heading, omit “for Member States”;

(b) in paragraph 1—

(i) for “National authorities shall” substitute “The approval authority must”;

(ii) for “EC” substitute “GB”;

(iii) omit “or national type-approval”;

(c) in paragraph 2, for “National authorities shall” substitute “The Secretary of State must”.

(7) In Article 5c (measures for determining certain aspects of environmental performance of some categories of vehicles)—

(a) in the first subparagraph, in the opening words, for the words from “2021, the Commission” to the end, substitute “2024, the Secretary of State must by regulations specify the following”;

(b) omit the second subparagraph.

(8) In Article 8 (timetable for application of type-approval of vehicles and engines)—

(a) in paragraph 1—

(i) in the first subparagraph—

(aa) for “national authorities shall” substitute “the approval authority must”;

(bb) for “EC type-approval or national type approval” substitute “GB type-approval”;

(ii) in the second subparagraph, for “on the Community market” substitute “on the market in Great Britain”;

(b) in paragraph 2—

(i) in the first subparagraph—

(aa) for “national authorities shall”, both times it occurs, substitute “the Secretary of State must”;

(bb) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(ii) in the second subparagraph, for the words from “national authorities” to the end, substitute “the sale or use of new engines which do not comply with this Regulation and its implementing measures is prohibited”;

(c) in paragraph 3—

(i) for “national authorities” substitute “the Secretary of State”;

(ii) for “EC type-approval or national type approval” substitute “GB type-approval”.

(9) In Article 9 (obligations of member States concerning type-approval of replacement parts)—

(a) in the heading, omit “of Member States”;

(b) for “shall be prohibited” substitute “is prohibited”.

(10) Omit Articles 10 (financial incentives) and 11 (penalties).

(11) In Article 12 (redefinition of specifications)—

(a) in paragraph 1—

(i) for “Commission shall” both times it occurs, substitute “Secretary of State must, by regulations”;

(ii) for “the Community” both times it occurs, substitute “Great Britain”;

(iii) omit the third subparagraph;

(b) omit paragraph 2;

(c) in paragraph 3—

(i) in the first subparagraph, for “The Commission shall” substitute “The Secretary of State must”;

(ii) in the second subparagraph—

(aa) in the first sentence, for “they shall be adapted so as to adequately reflect”, substitute “the Secretary of State must by regulations adapt them so that they adequately reflect”;

(bb) omit the second sentence;

(d) omit paragraph 4.

(12) For Article 13 (committee procedure) substitute—

“Article 13 Regulations

1.   Any power to make regulations conferred on the Secretary of State by this Regulation is exercisable by statutory instrument.

2.   Such regulations may—

(a) make incidental, supplemental, consequential or transitional provision, and

(b) make different provision for different cases or descriptions of case, different circumstances, different purposes or different areas.

3.   Before making any Regulations under this Regulation the Secretary of State must consult with such representative organisations as the Secretary of State thinks fit.

4.   A statutory instrument containing regulations made under this Regulation is subject to annulment in pursuance of a resolution of either House of Parliament.”.

(13) Omit Articles 13a (committee procedure) and 14 (implementation).

(14) After Article 18 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”

Commission Regulation (EC) No 631/2009

54.  In Commission Regulation (EC) No 631/2009, after Article 4, omit “This Regulation shall be binding in its entirety and directly applicable in all Member States”.

Regulation (EC) No 661/2009

55.—(1) Regulation (EC) No 661/2009 is amended as follows.

(2) In Article 2 (scope), for “Section A of Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 3 (definitions), for “Directive 2007/46/EC”, substitute “Regulation (EU) 2018/858”.

(4) In Article 4 (general obligations)—

(a) in paragraph 1, for “the Community” substitute “Great Britain”;

(b) in paragraph 2, for “EC” substitute “GB”;

(c) in paragraph 3, for “the Community” substitute “Great Britain”.

(5) In Article 12(2) (electronic stability control systems), in the opening words and in point (b), for “Section A of Annex II to Directive 2007/46/EC” substitute “Part A of Annex I of Regulation (EU) 2018/858”.

(6) In the heading to Chapter III, for “Member States” substitute “approval authority”.

(7) In Article 13 (type-approval of vehicles, components and separate technical units)—

(a) in paragraph 1—

(i) for “national authorities” both times it occurs, substitute “the approval authority”;

(ii) for “EC type-approval or national type-approval”, both times it occurs, substitute “GB type-approval”;

(b) in paragraph 2—

(i) in the opening words, for “national authorities” substitute “the approval authority”;

(ii) in point (a), for “EC type-approval or national type-approval” substitute “GB type-approval”;

(iii) in point (b), for “EC” substitute “GB”;

(c) in paragraph 3—

(i) for “national authorities” both times it occurs, substitute “the approval authority”;

(ii) in the first sub-paragraph, for “EC” substitute “GB”;

(iii) in the second sub-paragraph, for “EC type-approval or national type-approval” substitute “GB type-approval”;

(d) in paragraphs 4, 5, 6, 8, 9, 10, 13, and 15, for “national authorities”, substitute “the Secretary of State”;

(e) in paragraphs 4, 5(a), 6(a), 9(a), 10(a) and 13, for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(f) in paragraph 7—

(i) for “national authorities” substitute “the approval authority”;

(ii) for “EC” substitute “GB”;

(g) in paragraph 8, for “EC-type-approval or national type-approval” substitute “GB type-approval”;

(h) in paragraph 12, for “EC-type-approval or national type-approval” substitute “GB type-approval”;

(i) in paragraph 14—

(i) in the first subparagraph—

(aa) for “National authorities shall” substitute “The Secretary of State must”;

(bb) after “3 and” insert “the approval authority must”;

(ii) in the second sub-paragraph—

(aa) for “National authorities shall” substitute “The Secretary of State must”;

(bb) after “service of, and” insert “the approval authority must”;

(cc) for “EC type-approval” substitute “GB type-approval”;

(j) in paragraph 15(a)—

(i) for “EC-type-approval or national type-approval” substitute “GB type-approval”;

(ii) for “EC component” substitute “GB component”.

(8) In Article 14 (implementing measures)—

(a) in paragraph 1, in the opening words, for “Commission shall” substitute “Secretary of State may by regulations”;

(b) in point (b), omit “within or between Member States”;

(c) in point (f), for “that are mandatory under Article 4(4) of Decision 97/836/EC” substitute “which the United Kingdom has voted in favour of”;

(d) omit paragraph 2;

(e) in paragraph 3—

(i) in the opening words, for “Commission may” substitute “Secretary of State may by regulations”;

(ii) omit point (b);

(f) omit paragraph 4.

(9) For Article 15 (committee procedure), substitute—

“Article 15 Regulations

1.   Any power to make regulations conferred on the Secretary of State by this Regulation is exercisable by statutory instrument.

2.   Such regulations may—

(a) make incidental, supplemental, consequential or transitional provision, and

(b) make different provision for different cases or descriptions of case, different circumstances, different purposes or different areas.

3.   Before making any regulations in accordance with this Article, the Secretary of State must consult with such representative organisations as the Secretary of State thinks fit.

3.   A statutory instrument containing regulations made under this Regulation is subject to annulment in pursuance of a resolution of either House of Parliament.”.

(10) Omit Articles 16 and 17.

(11) After Article 20, omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.

(12) In Annex IV, in the notes to the table—

(a) in the second paragraph, for “Articles 26 and 28 of Directive 2007/46” substitute “Articles 48 and 50 of Regulation (EU) 2018/858”;

(b) in the final sentence of the third paragraph—

(i) for “national authorities” substitute “the Secretary of State”;

(ii) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(c) in note (a), for “EC” substitute “GB”;

(d) in note (f), in the opening words, for “point 2.11.5 of Annex I to Directive 2007/46/EC” substitute “point 1.9 of Annex I to Commission Implementing Regulation (EU) 2020/683”;

(e) in note (h), for “an EC” substitute “a GB”.

Commission Regulation (EU) No 406/2010

56.—(1) Commission Regulation (EU) No 406/2010 is amended as follows.

(2) In Article 2 (administrative provisions for EC type-approval of a vehicle with regard to hydrogen propulsion)—

(a) in the heading and paragraph 1, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraphs 2 and 4, for “an EC type-approval” substitute “a GB type-approval”;

(c) in paragraph 3—

(i) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) for “A Member State” substitute “The approval authority”.

(3) In Article 3 (administrative provisions for EC component type-approval of hydrogen components)—

(a) in the heading and paragraph 1, for “EC component type-approval” substitute “GB component type-approval”;

(b) in paragraph 2—

(i) for “an EC component type-approval” substitute “a GB component type-approval”;

(ii) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(iii) for “A Member State” substitute “The approval authority”;

(iv) in paragraph 3, for “an EC type-approval” substitute “a GB type-approval”.

(4) In Article 4 (regulatory provisions which do not apply)—

(a) in the opening words—

(i) for “EC” substitute “GB”;

(ii) for “Articles 6 and 9 of Directive 2007/46/EC” substitute “Article 22(1) of Regulation (EU) 2018/858”;

(b) in point (1), for “Council Directive 80/1268/EEC” substitute “Regulation (EC) 715/2007 in respect of the determination of fuel consumption and CO₂ emissions”;

(c) in point (2), for “Council Directive 80/1269/EEC” substitute “Regulation (EC) 715/2007 or Regulation (EC) No 595/2009, both in respect of the determination of engine power”;

(d) in point (3), for “Annex I to Council Directive 70/2221/EEC” substitute “UN Regulation 34, as amended by the 03 series of amendments(22)”;

(e) in point (4), for “Section 3.3.5 of Annex II and Section 4.3.2 of Appendix 1 to Annex II to Directive 96/27/EC of the European Parliament and of the Council” substitute “paragraph 5.3.6 of, and paragraph 4.3.2 of Annex 4 to, UN Regulation 95, as amended by the 03 series of amendments(23)”;

(f) in point (5) for “Section 3.2.6 of Annex II and Section 1.4.2.2 of Appendix 1 to Annex II to Directive 96/79/EC of the European Parliament and of the Council” substitute “paragraphs 5.2.6 of, and paragraph 1.4.2.2 of Annex 3 to, UN Regulation 94, as amended by the 03 series of amendments(24)”.

(5) In Article 5 (EC component type-approval mark)—

(a) for “EC” in the heading and the first time it occurs, substitute “GB”;

(b) for “an EC” substitute “a GB”.

(6) After Article 6 (entry into force), omit “This Regulation shall be binding in its entirely and directly applicable in all Member States.”

(7) In the list of Annexes, for “EC” each time it occurs, substitute “GB”.

(8) In Annex I (administrative documents for EC type-approval of vehicles re hydrogen propulsion)—

(a) in the title of the Annex and in the heading of the information document in Part 1, for “EC” substitute “GB”;

(b) in Part 1 (model information document)—

(i) in the explanatory notes following paragraph 3.9.2.6, in note (c), for “Part A of Annex II to Directive 2007/46/EC” substitute “Article 4 to Regulation (EU) 2018/858”;

(ii) in the Appendix to the information document, in the entry for “Container statement of service”, after “406/2010” insert “as it has effect in domestic law”;

(c) in Part 2 (model EC type-approval certificate)—

(i) for “EC type-approval” each time it occurs, substitute “GB type-approval”;

(ii) in the words before Section I, after “406/2010” insert “as it has effect in domestic law, as last amended by S.I. …./….”;

(iii) in Section I, for paragraphs 0.1 to 0.9 substitute—

“(to be completed in accordance with Section 1 of the template of Model B in Annex III to Commission Implementing Regulation (EU) 2020/683)”;

(iv) in Section II, for paragraphs 1 to 8, and the list of attachments, substitute—

“(to be completed in accordance with Section II of the template of Model B in Annex III to Commission Implementing Regulation (EU) 2020/683)”;

(v) in the Addendum, for “EC” in the heading both times it occurs, substitute “GB”;

(d) in Part 3 (information to be provided for inspection)—

(i) in paragraph 1(b), for “Council Directive 76/114/EEC” substitute “Commission Regulation (EU) No 19/2011(25)”;

(ii) in paragraph 2—

(aa) for “approval authorities” substitute “the approval authority”;

(bb) omit “in the Member States”.

(9) In Annex II (administrative documents for EC component type-approval of hydrogen components and systems)—

(a) in the title, and each other time it occurs (except in references to “Regulation (EC) No 79/2009”), including in the Addendum to Part 2, for “EC” substitute “GB”;

(b) in Part 2 (model EC type-approval certificate)—

(i) in the words before Section 1, after “406/2010” insert “, as last amended by S.I. …./….”;

(ii) in Section 1, for paragraphs 0.1 to 0.9 substitute—

“(to be completed in accordance with Section I of the template of Model C in Annex III to Commission Implementing Regulation (EU) 2020/683)”;

(iii) in Section II, for paragraphs 1 to 8 and the following list of attachments, substitute—

“(to be completed in accordance with Section II of the template of Model C in Annex III to Commission Implementing Regulation (EU) 2020/683)”;

(c) in Part 3 (EC component type-approval mark)—

(i) for paragraph 1.1, substitute—

“1.1.   A rectangle surrounding the lower-case letter ‘g’ followed by the number 11.”;

(ii) in the Addendum to Appendix 1—

(aa) for the image, substitute—

“

”

(bb) in the legend, for “by Belgium” substitute “by the United Kingdom”.

(10) In Annex III (requirements for hydrogen components and systems designed to use liquid hydrogen)—

(a) in Part 1, in point 2.4, for “Directives 96/27/EC and 96/79/EC of the European Parliament and of the Council” substitute “UN Regulation 94 and UN Regulation 95”;

(b) in Part 2, in point 5.5.1, for “EC” substitute “GB”.

(11) In Annex IV (requirements for hydrogen components and systems designed to use compressed hydrogen)—

(a) for “EC”, each time it occurs (except in references to “Regulation (EC) No 79/2009”), substitute “GB”;

(b) in Part 1, in point 2.3, for “Directives 96/27/EC and 97/79/EC” substitute “UN Regulation 94 and UN Regulation 95”.

Commission Regulation (EU) No 672/2010

57.—(1) Commission Regulation (EU) No 672/2010 is amended as follows.

(2) In Article 1 (scope), for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 3 (provisions for EC type-approval of a vehicle re windscreen defrosting and demisting systems)—

(a) in paragraph 1, and in the heading to the Article, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraphs 3 and 4, for “an EC type-approval” substitute “a GB type-approval”;

(c) in paragraph 3—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC”, substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”.

(4) In Article 4—

(a) omit “National authorities shall permit”;

(b) for “661/2009 and” substitute “661/2009 is permitted, and the approval authority must”.

(5) Omit “This Regulation shall be binding in its entirety and directly applicable in all Member States” following Article 5.

(6) In Annex I (administrative documents for EC type-approval of motor vehicles re windscreen defrosting and demisting systems)—

(a) for “EC type-approval” in the title and each other time it occurs, including in the heading to Annex I, substitute “GB type-approval”;

(b) in point 9.1, for “Annex II of Directive 2007/46/EC” substitute “Annex I of Regulation (EU) 2018/858”;

(c) in the notes following Part 1—

(i) in note (^c), for “Directive 2007/46/EC Part A of Annex II” substitute “Article 4 of Regulation (EU) 2018/858”;

(ii) in note (ⁿ), for “Council Directive 80/1269/EEC (OJ L 375, 31.12.1980, p. 46)” substitute “Regulation (EC) 715/2007 (EUR 2007/715)”;

(d) in Part 2—

(i) in the words before Section I, for “as last amended by Regulation (EU) No … / …” substitute “as it has effect in domestic law, as last amended by S.I. …. /……”;

(ii) in the notes following Section II of Part 2, in note (³), for “Directive 2007/46/EC, Annex II, Section A” substitute “Article 4 of Regulation (EU) 2018/858”.

Commission Regulation (EU) No 1003/2010

58.—(1) Commission Regulation (EU) No 1003/2010 is amended as follows.

(2) In Article 2 (provisions for EC type-approval of a motor vehicle or a trailer re the space for rear registration plates)—

(a) in the heading, and in paragraph 1, for “EC type-approval”, substitute “GB type-approval”;

(b) in paragraph 3—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”;

(c) in paragraphs 3 and 4, for “an EC type-approval” substitute “a GB type-approval”.

(3) In Article 3 (validity and extension of approvals granted under Directive 70/222/EEC)—

(a) omit “National authorities shall permit”;

(b) for “661/2009 and” substitute “661/2009 is permitted, and the approval authority must”.

(4) Omit “This Regulation shall be binding in its entirety and directly applicable in all Member States” following Article 4.

(5) In Annex I (administrative documents for EC type-approval of motor vehicles and their trailers re the space for rear registration plates)—

(a) for “EC type-approval”, each time it occurs including in the heading, substitute “GB type-approval”;

(b) in the explanatory notes at the end of Part 1, in note (^c), for “Directive 2007/46/EC Part A of Annex II” substitute “Article 4 of Regulation (EU) 2018/858”;

(c) in Part 2—

(i) in the words before section 1, for “as last amended by Regulation (EU) No … / …” substitute “as it has effect in domestic law, as last amended by S.I. …. /……,”;

(ii) in note (3) to point 0.4 of Section I, for “Directive 2007/46/EC, Annex II, Section A” substitute “Article 4 of Regulation (EU) 2018/858”.

(6) In Annex II (requirements for the space for mounting and fixing rear registration plates), in point 1.2.3—

(a) for “point 2.11.5 of Annex I to Directive 2007/46/EC” substitute “point 1.9 of Annex I to Commission Implementing Regulation (EU) 2020/683”;

(b) for “EC type-approval” substitute “GB type-approval”.

Commission Regulation (EU) No 1005/2010

59.—(1) Commission Regulation (EU) No 1005/2010 is amended as follows.

(2) For “EC type-approval”, each time it occurs, except in Article 3, paragraphs 3 and 4, substitute “GB type-approval”.

(3) In Article 1 (scope), for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(4) In Article 3 (provisions for EC type-approval of a vehicle re towing devices)—

(a) in paragraph 3—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”.

(b) in paragraphs 3 and 4, for “an EC type-approval” substitute “a GB type-approval”.

(5) In Article 4 (validity and extension of approvals granted under Directive 77/389/EEC)—

(a) omit “National authorities shall permit”;

(b) for “661/2009, and” substitute “661/2009 is permitted, and the approval authority must”.

(6) Omit “This Regulation shall be binding in its entirety and directly applicable in all Member States” following Article 5.

(7) In Annex I (administrative documents for EC type-approval of vehicles re towing devices)—

(a) after paragraph 1.1, insert—

“1.9.   Specify if the towing vehicle is intended to tow semi-trailers or other trailers and if the trailer is—

(a) a semi-trailer,

(b) a drawbar-trailer,

(c) a centre-axle-trailer, or

(d) a rigid-drawbar trailer.”;

(b) omit paragraph 2.11.5;

(c) in the explanatory notes at the end of Part 1, in note (c), for “Directive 2007/46/EC Part A of Annex II” substitute “Article 4 of Regulation (EU) 2018/858”;

(d) in Part 2—

(i) in the words before section 1, for “as last amended by Regulation (EU) No … / …” substitute “as it has effect in domestic law, as last amended by S.I. …. /……,”;

(ii) in note (3) to point 0.4 of Section I, for “Directive 2007/46/EC, Annex II, Section A” substitute “Article 4 of Regulation (EU) 2018/858”.

(8) In Annex II (requirements for towing devices), in point 1.1.2, for “Directive 2007/46/EC Part A of Annex II” substitute “Article 4 of Regulation (EU) 2018/858”.

Commission Regulation (EU) No 1008/2010

60.—(1) Commission Regulation (EU) No 1008/2010 is amended as follows.

(2) For—

(a) “an EC type-approval”, in Article 3(3) and 3(4), and in Article 4(3), substitute “a GB type-approval”;

(b) in all other cases, for “EC type-approval”, each time it occurs, substitute “GB type-approval”.

(3) In Article 1 (scope), for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(4) In Article 3(3) (EC type-approval of a vehicle re windscreen wiper and washer systems)—

(a) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(b) in the second subparagraph, for “A Member State” substitute “The approval authority”.

(5) In Article 4 (EC separate technical unit type-approval of windscreen washer systems)—

(a) in the heading, and both other times it appears, for “EC separate” substitute “GB separate”;

(b) in paragraph 2—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”.

(6) In Article 5 (EC separate technical unit type-approval mark)—

(a) in the heading and both other times it appears, for “EC” substitute “GB”;

(b) at the end insert as a new subparagraph—

“This Article does not apply to a separate technical unit which was manufactured before 1 February 2026 and is of a type which has been approved by an approval authority of a member State in accordance with Commission Regulation (EU) 1008/2010(26) or Annex IV to Commission Implementing Regulation (EU) 2021/535(27), in each case as they have effect in EU law.”.

(7) In Article 6—

(a) omit “National authorities shall permit”;

(b) for “661/2009, and” substitute “661/2009 is permitted, and the approval authority must”.

(8) Omit “This Regulation shall be binding in its entirety and directly applicable in all ms” following Article 7.

(9) In Annex I (administrative documents for vehicles re their windscreen wiper and washer systems)—

(a) in the explanatory notes at the end of Part 1—

(i) in note (c), for “Directive 2007/46/EC Part A of Annex II” substitute “Article 4 of Regulation (EU) 2018/858”;

(ii) in note (n), for “Directive 80/1269/EEC (OJ L 375, 31.12.1980, p. 46)” substitute “Regulation (EU) No 715/2007 (EUR 2007/715)”;

(b) in Part 2—

(i) in the words before section 1, for “as last amended by Regulation (EU) No … / …” substitute “as it has effect in domestic law, as last amended by S.I. …. /……,”;

(ii) in note (3) to point 0.4 of Section I, for “Directive 2007/46/EC, Annex II, Section A” substitute “Article 4 of Regulation (EU) 2018/858”.

(10) In Annex II (Administrative documents for EC type-approval of windscreen washer systems as separate technical units)—

(a) in Part 1, in point 0.7, for “EC” substitute “GB”;

(b) in Part 2—

(i) in the words before section 1, for “as last amended by Regulation (EU) No … / …” substitute “as it has effect in domestic law, as last amended by S.I. …. /……,”;

(ii) in Section I, in point 0.7, for “EC” substitute “GB”;

(c) in Part 3—

(i) in the heading and in point 1, for “EC” substitute “GB”;

(ii) for point 1.1, substitute—

“1.1.   A rectangle surrounding the lower-case letter “g”, followed by the number “11”.”

(iii) in point 2, for “EC” substitute “GB”;

(iv) in point 3—

(aa) for “EC”, both times it occurs, substitute “GB”;

(bb) for figure 1, substitute the following image—

“

”

(v) in the explanatory note following point 3—

(aa) for “EC” substitute “GB”;

(bb) omit “by The Netherlands”.

Commission Regulation (EU) No 1009/2010

61.—(1) Commission Regulation (EU) No 1009/2010 is amended as follows.

(2) In Article 1 (scope), for “Annex II to Directive 2007/46/EC” substitute “Article 4 to Regulation (EU) 2018/858.”

(3) In Article 3 (provisions for EC type-approval of a vehicle re wheel guards)—

(a) in the heading and in paragraph 1, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraph 3—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State”, substitute “The approval authority”.

(c) in paragraphs 3 and 4, for “an EC” substitute “a GB”.

(4) In Article 4 (validity and extension of approvals granted under Directive 78/549/EEC)—

(a) omit “National authorities shall permit”;

(b) for “661/2009 and” substitute “661/2009 is permitted, and the approval authority must”.

(5) Omit “This Regulation shall be binding in its entirety and directly applicable in all Member States” following Article 5.

(6) In Annex I (administrative documents for vehicles for EC type-approval of wheel guards)—

(a) in the heading, for “EC type-approval” substitute “GB type-approval”;

(b) in Part 1—

(i) in the first point, for “EC type-approval” substitute “GB type-approval”;

(ii) in the notes to Part 1, in the note (^c) to point 0.4, for “Directive 2007/46/EC, Part A of Annex II” substitute “Article 4 of Regulation (EU) 2018/858”;

(c) in Part 2—

(i) in the heading and each time it occurs, for “EC type-approval” substitute “GB type-approval”;

(ii) in the opening section, for “as last amended by Regulation (EU) No …/” substitute “as it forms part of domestic law, and as last amended by S.I. …./….”;

(iii) in the notes to Part 2, in note (³) to point 0.4, for “Directive 2007/46/EC, Annex II, Section A” substitute “Article 4 of Regulation (EU) 2018/858”;

(d) in the Addendum to Part 2, in the heading “for “EC type-approval” substitute “GB type-approval”.

Commission Regulation (EU) No 19/2011

62.—(1) Commission Regulation (EU) No 19/2011 is amended as follows.

(2) In Article 2(3) (definitions), for “Annex II, Part B to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 3 (provisions for EC type-approval of a type of vehicle re the manufacturer’s statutory plate and vehicle identification number)—

(a) in the heading and in paragraph 1, for “EC” substitute “GB”;

(b) in paragraph 4—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”;

(c) in paragraph 5, for “an EC” substitute “a GB”.

(4) In Article 4 (validity and extension of EC type-approvals granted under Directive 76/114/EEC)—

(a) omit “National authorities shall permit”;

(b) for “661/2009 and” substitute “661/2009 is permitted, and the approval authority must”.

(5) After Article 5 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States”.

(6) In Annex I (technical requirements), after point 2.3, insert—

“2.4.   By way of derogation from point 2.1(b)—

(a) for vehicles manufactured on or before 31st January 2024 which are of a type approved by an approval authority of a member State under Regulation (EU) 2018/858(28) as it applies in EU law, the manufacturer may instead print the whole vehicle type approval number according to Annex IV of Commission Implementing Regulation (EU) 2020/683 as it applies in EU law;

(b) a vehicle which is of a type which has been approved by an approval authority of a member State in accordance with Regulation (EU) 2018/858 as it applies in EU law may be fitted with a statutory plate which is printed with the whole vehicle type approval number in accordance with Annex IV of Commission Implementing Regulation (EU) 2020/683(29) as it applies in EU law, instead of the GB whole vehicle type approval number. In this case, the GB whole vehicle type approval number (in accordance with Annex IV of Commission Implementing Regulation (EU) 2020/683) must be printed on the statutory plate below or to the side of the “clearly marked rectangle” referred to in point 4.1.

2.5.   By way of derogation from point 2.1, a vehicle which is of a type which has been approved by an approval authority of a member State in accordance with Regulation (EU) 2018/858 as it applies in EU law, may be fitted with a statutory plate that does not contain the information required in sub-paragraph 2.1(d) to (f) if it is also fitted with a statutory plate complying with Commission Regulation (EU) 19/2011(30) or with Annex II to Regulation (EU) 2021/535(31), in each case as they apply in the EU.”.

(7) In the Appendix to Annex I—

(a) in paragraph 1—

(i) for “e3*2007/46*0004” substitute “g11*2007/46*0004”;

(ii) for “Italy” substitute “Great Britain”;

(b) in paragraph 2—

(i) for “e1*2007/46*0345” substitute “g11*2007/46*0345”;

(ii) for “Germany” substitute “Great Britain”;

(c) in paragraph 3—

(i) for “e11*2007/46*0085” substitute “g11*2007/46*0085”;

(ii) for “the United Kingdom” substitute “Great Britain”;

(d) in paragraph 4—

(i) for “e6*2007/46*0098” substitute “g11*2007/46*0098”;

(ii) for “Belgium” substitute “Great Britain”.

(8) In Annex II, in paragraph 1.1, for “national authority” substitute “approval authority”.

(9) In Annex III—

(a) in Part A (information document)—

(i) in the first paragraph, for “EC” substitute “GB”;

(ii) in point 0.6, for “manufacturer’s statutory plate” substitute “statutory plates and location of vehicle identification number”;

(iii) omit points 0.7, 0.7.1 and 0.7.2;

(b) in the explanatory notes following Part A of Annex III, in note (^b), for “Directive 2007/46/EC Part A of Annex II”, substitute “Article 4 of Regulation (EU) 2018/858”;

(c) in Part B (EC type-approval certificate)—

(i) in the heading, and each time it appears, for “EC” substitute “GB”;

(ii) for “Regulation (EU) No …/…, as last amended by Regulation (EU) No …/….” substitute “Regulation (EU) No 19/2011 as it forms part of domestic law, as last amended by S.I. …./…..”;

(d) in the explanatory notes following Part B of Annex III, in note (³), for “Annex II Section A” substitute “Article 4 of Regulation (EU) 2018/858”;

(e) in the Addendum to Part B, for “EC” substitute “GB”.

Commission Regulation (EU) No 109/2011

63.—(1) Commission Regulation (EU) No 109/2011 is amended as follows.

(2) In Article 1 (scope), for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 2 (definitions)—

(a) in point (11), for the words from “point 2.15” to the end, substitute “point 35 of Article 2 of Commission Regulation (EU) No. 1230/2012(32)”;

(b) in point (12), for the words from “point 2.6” to the end, substitute “point 4 of Article 2 of Commission Regulation (EU) No. 1230/2012”;

(c) in point (13), for the words from “as defined” to the end, substitute “which comes into contact with the ground”;

(d) in point (15), for “as defined in point 2.1.1.2.2 of Annex I to Directive 97/27/EC” substitute “which is designed and constructed exclusively or principally to tow semi-trailers”;

(e) in point (16), for “point 2.8 of Annex I to Directive 2007/46/EC”, substitute “point 7 of Article 2 of Commission Regulation (EU) No. 1230/2012”.

(4) In Article 3 (EC type-approval of a vehicle re spray suppression systems)—

(a) in the heading, and in paragraph 1, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraphs 3 and 4, for “an EC type-approval” substitute “a GB type-approval”;

(c) in paragraph 3—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “An approval” substitute “The approval”.

(5) In Article 4 (EC separate technical unit type-approval of spray suppression systems)—

(a) in the heading, and in paragraph 1 for “EC separate” substitute “GB separate”;

(b) in paragraph 2—

(i) in the first subparagraph—

(aa) for “an EC” substitute “a GB”;

(bb) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “An approval” substitute “The approval”;

(c) in paragraph 3, for “EC type-approval” substitute “GB type-approval”.

(6) In Article 5 (EC separate technical unit type-approval mark)—

(a) for “EC separate”, in the heading and the first other time it occurs, substitute “GB separate”;

(b) for “an EC” substitute “a GB”;

(c) at the end, insert as a new subparagraph—

“This Article does not apply to a separate technical unit which was manufactured before 1 February 2026 and is of a type which has been approved by an approval authority of a member State in accordance with Commission Regulation (EU) 109/2011(33) or Annex VIII of Commission Implementing Regulation (EU) 2021/535(34), in each case as they have effect in EU law.”.

(7) In Article 6—

(a) omit “National authorities shall permit”;

(b) for “2012 and” substitute “2012 is permitted, and the approval authority must”.

(8) After Article 7 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”

(9) In Annex I (administrative documents for EC type approval of vehicles re their spray suppression systems)—

(a) in the heading and in the first paragraph of Part 1, for “EC type-approval” substitute “GB type-approval”;

(b) in Part 2—

(i) in the certificate heading, and each time it occurs, for “EC type-approval” substitute “GB type-approval”;

(ii) in the opening section, for “Regulation (EU) … / …, as last amended by Regulation (EU) No …/…” substitute “Regulation (EU) No 109/2011, as it has effect in domestic law, and as last amended by S.I. …../……”;

(c) in note (3) after Part 2, for “Directive 2007/46/EC, Annex II, Section A” substitute “Article 4 of Regulation (EU) 2018/858”;

(d) in the heading to the Addendum to Part 2, for “EC type-approval” substitute “GB type-approval”.

(10) In Annex II (administrative documents for EC type-approval of spray suppression systems as separate technical units)—

(a) in the heading and each time it occurs, for “EC type-approval” substitute “GB type-approval”;

(b) in Part 1—

(i) in point 0.7, for “EC approval” substitute “GB approval”;

(ii) in point 1.3, for “EC component” substitute “GB component”;

(c) in Part 2—

(i) in the opening section, for “Regulation (EU) No … / …, as last amended by Regulation (EU) No …/…” substitute “Regulation (EU) No 109/2011, as it has effect in domestic law, and as last amended by S.I. …../……”;

(ii) in point 0.7 of section I, for “EC approval” substitute “GB approval”;

(d) in Part 3—

(i) for point 1.1, substitute—

“1.1.   A rectangle surrounding the lower-case letter “g” followed by the number “11”.”

(ii) in point 3, for the example of a separate technical unit type-approval mark, substitute—

“

”.

(iii) in the legend following the example, omit “by The Netherlands”.

(11) In Annex III (requirements and tests for spray suppression devices)—

(a) in the heading to point 2, for “EC component” substitute “GB component”;

(b) in point 2.1—

(i) for “EC component” substitute “GB component”;

(ii) for “Article 7 of Directive 2007/46/EC” substitute “Article 23 of Regulation (EU) 2018/858”;

(c) in point 2.4.1, for “EC component” substitute “GB component”;

(d) in point 2.4.2, for “the Appendix of Annex VII to Directive 2007/46/EC” substitute “Annex V to Commission Implementing Regulation (EU) 2020/683”.

(12) In Annex IV (requirements for type-approval of vehicles re their spray suppression systems), in point 0.1, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”.

(13) In Annex V (conformity of production and cessation of production)—

(a) in point 1.1, 1.2 and 2, for “EC component” each time it occurs, substitute “GB component”;

(b) in point 1.1 for “EC type-approval” substitute “GB type-approval”.

Commission Regulation (EU) No 458/2011

64.—(1) Commission Regulation (EU) No 458/2011 is amended as follows.

(2) In Article 1 (scope), for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 3 (EC type-approval of a vehicle re the installation of its tyres)—

(a) in the heading, and in paragraph 1, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraph 3—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”;

(c) in paragraphs 3 and 4, for “an EC type-approval” substitute “a GB type-approval”.

(4) After Article 4 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.

(5) In Annex I (administrative provisions for the type-approval of vehicles re the installation of their tyres)—

(a) in Part 1—

(i) in the first paragraph, for “EC type-approval” substitute “GB type-approval”;

(ii) in the explanatory notes following Part 1, in note (^c) to point 0.4, for “Directive 2007/46/EC Part A of Annex II” substitute “Article 4 of Regulation (EU) 2018/858”;

(b) in Part 2—

(i) in the heading and each time it occurs, for “EC type-approval” substitute “GB type-approval”;

(ii) in the opening section, for “Regulation (EU) No …/2011” substitute “Commission Regulation (EU) No 458/2011 as it has effect in domestic law, and as last amended by S.I. …./…”;

(iii) in the explanatory notes following Part 2, in note (³) to point 0.4, for “Directive 2007/46/EC, Annex II, Section A”, substitute “Article 4 of Regulation (EU) 2018/858”;

(c) in the Addendum to Part 2—

(i) in the heading, for “EC type-approval” substitute “GB type-approval”;

(ii) in point 4, after “Regulation No 64” insert “or UNECE Regulation No 141(35)”.

Commission Regulation (EU) No 582/2011: Articles

65.—(1) Commission Regulation (EU) No 582/2011 is amended as follows.

(2) In Article 2 (definitions), omit point (44).

(3) Omit Articles 2a (access to vehicle OBD and vehicle repair and maintenance information) to 2h (forum on access to vehicle information).

(4) In Article 3 (requirements for type-approval)—

(a) in paragraph 1—

(i) for “EC type-approval”, the second time it occurs, substitute “GB type-approval”;

(ii) omit “and vehicle repair and maintenance information” each time it occurs;

(iii) in the second subparagraph, for “in the Union” substitute “in Great Britain”;

(b) in paragraphs 1, 2, 4, 6, 7 and 8, for “an EC type-approval” each time it occurs, substitute “a GB type-approval”;

(c) omit paragraphs 1a to 1c;

(d) in paragraphs 2 and 3, omit “and vehicle repair and maintenance information” each time it occurs;

(e) in paragraph 3, for “the EC type-approval” substitute “the GB type-approval”;

(f) in paragraph 6, omit “and vehicle repair and maintenance information”;

(g) in paragraph 14, after “the Union” insert “or the United Kingdom”.

(5) In Article 4 (on-board diagnostics)—

(a) in paragraph 3, after “the Union” insert “or the United Kingdom”;

(b) omit paragraph 8.

(6) In Article 5 (application for EC type-approval of an engine system or family as a separate technical unit re emissions etc)—

(a) in the heading—

(i) for “EC” substitute “GB”;

(ii) omit “and access to repair and maintenance information”;

(b) in paragraph 1, for “EC” substitute “GB”;

(c) in paragraph 4, omit points (d) and (g).

(7) In Article 6 (administrative provisions for EC type-approval of an engine system or family as a separate technical unit re emissions etc)—

(a) in the heading—

(i) for “EC type-approval” substitute “GB type-approval”;

(ii) omit “and access to repair and maintenance information”;

(b) in paragraph 1—

(i) in the first sub-paragraph, for “an EC type-approval” substitute “a GB type-approval”;

(ii) for “Annex VII to Directive 2007/46/EC”, both times it occurs, substitute “Annex IV to Commission Implementing Regulation 2020/683”;

(c) in paragraph 1a—

(i) in the opening words, for “an EC type-approval” substitute “a GB type-approval”;

(ii) in point (a), for “EC type-approval” substitute “GB type-approval”;

(iii) omit point (b);

(d) in paragraph 2, for “an EC type-approval” substitute “a GB type-approval”.

(8) In Article 7 (application for EC type-approval of a vehicle with an approved engine system re emissions etc)—

(a) in the heading, and in paragraphs 1 and 2, for “EC type-approval” substitute “GB type-approval”;

(b) in the heading, omit “and access to vehicle repair and maintenance information”;

(c) in paragraph 4, omit points (c) and (d).

(9) In Article 8 (administrative provisions for EC type-approval of a vehicle with an approved engine system re emissions etc)—

(a) in the heading—

(i) for “EC type-approval” substitute “GB type-approval”;

(ii) omit “and access to vehicle repair and maintenance information”;

(b) in paragraphs 1, 1a and 2, for “an EC type-approval”, each time it occurs, substitute “a GB type-approval”;

(c) in paragraph 1, in the opening words—

(i) omit “and access to vehicle repair and maintenance information”;

(ii) for “Annex VII to Directive 2007/46/EC”, both times it occurs, substitute “Annex IV to Commission Implementing Regulation 2020/683”;

(d) in paragraph 1a—

(i) in point (a), for “EC” substitute “GB”;

(ii) omit point (b);

(iii) in point (e), for “the Union” substitute “Great Britain”.

(10) In Article 9 (application for EC type-approval of a vehicle re emissions etc), in the heading and in paragraph 1—

(a) for “EC” substitute “GB”;

(b) omit “and access to vehicle repair and maintenance information”.

(11) In Article 10 (administrative provisions for EC type-approval of a vehicle re emissions)—

(a) in the heading, and in paragraph 1a(a), for “EC” substitute “GB”;

(b) in the heading, in the first sub-paragraph of paragraph 1, and in the opening words of paragraph 1a, omit “and access to vehicle repair and maintenance information”;

(c) in paragraph 1—

(i) for “an EU type-approval” substitute “a GB type-approval”;

(ii) for “Annex VII to Directive 2007/46/EC”, both times it occurs, substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(d) in paragraph 1a—

(i) in the opening words, for “an EU type-approval” substitute “a GB type-approval”;

(ii) omit point (b);

(iii) in point (e), for “the Union” substitute “Great Britain”;

(e) in paragraph 2, for “an EU type-approval”, both times it occurs, substitute “a GB type-approval”.

(12) In Article 11 (conformity of production), in paragraph 1, for “Article 12 of Directive 2007/46/EC” substitute “Article 31 of Regulation (EU) 2018/858”.

(13) In Article 12 (in-service conformity)—

(a) in paragraph 1, for “Article 12 of Directive 2007/46/EC” substitute “Article 31 of Regulation (EU) 2018/858”;

(b) in paragraph 5, omit “or based on in-service testing conducted by a Member State,”;

(c) in paragraph 6—

(i) for “Any Member State” substitute “The Secretary of State”;

(ii) for “its own” substitute “their own”;

(iii) omit the last sentence;

(d) omit paragraphs 7 to 10.

(14) In Article 13 (remedial measures)—

(a) in paragraph 3, for “Article 30(1) and 30(5) of Directive 2007/46/EC” substitute “Article 52 of Regulation (EU) 2018/858”;

(b) in paragraph 4, omit “and all Member States”.

(15) In Article 15 (pollution control devices), in paragraph 1, for “EC type-approved”, both times it occurs, substitute “GB type-approved”.

(16) In Article 16 (application for EC type-approval of replacement pollution control devices as separate technical units)—

(a) in the heading, and in paragraph 1, for “EC” substitute “GB”;

(b) omit paragraph 3.

(17) In Article 17 (administrative provisions for EC type-approval of replacement pollution control devices as separate technical units)—

(a) in the heading, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraphs 1 and 2, for “an EC type-approval” substitute “a GB type-approval”;

(c) in paragraph 1, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”.

(18) In Article 17a (transitional provisions)—

(a) in paragraph 1—

(i) for “national authorities” substitute “the approval authority”;

(ii) for “EC” substitute “GB”;

(iii) omit “or national type-approval”;

(b) in paragraph 2—

(i) for “national authorities” both times it occurs, substitute “the Secretary of State”;

(ii) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”.

(19) After Article 20 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.

(20) In the list of Annexes, for “EC type-approval”, each time it occurs, substitute “GB type-approval”.

Commission Regulation (EU) No 582/2011: Annexes

66.—(1) The Annexes to Commission Regulation (EU) No 582/2011 are amended as follows.

(2) In Annex I (administrative provisions for EC type-approval)—

(a) in the heading and each other time it occurs, except in points 3.2 and 3.4, for “EC type-approval” substitute “GB type-approval”;

(b) in point 1.1.2—

(i) in the opening words, for “Directive 98/70/EC of the European Parliament and of the Council” substitute “the Motor Fuel (Composition and Content) Regulations 1999(36)”;

(ii) in point (c), for “Directive 98/70/EC” substitute “the Motor Fuel (Composition and Content) Regulations 1999”;

(c) in point 3.1, omit “and access to vehicle repair and maintenance information”;

(d) in point 3.2, for “an EC type-approval” substitute “a GB type-approval”;

(e) for point 3.2.1 substitute—

“3.2.1.   A rectangle surrounding the lower-case letter ‘g’ followed by the number 11.”;

(f) in point 3.2.2, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(g) in point 3.2.3 and 3.2.4, for “EC approval mark”, each time it occurs, substitute “GB approval mark”;

(h) in point 3.4—

(i) for “EC type-approval” the first time it occurs, substitute “GB type-approval”;

(ii) for “an EC type-approval” substitute “a GB type-approval”;

(iii) omit “and access to vehicle repair and maintenance information”;

(i) in point 7.1—

(i) for “Article 12 of Directive 2007/46/EC” substitute “Article 31 of Regulation (EU) 2018/858”;

(ii) for “Annex X to Directive 2007/46/EC” substitute “Annex IV to Regulation (EU) 2018/858”;

(j) in point 7.2.2.2, for “Annex X to Directive 2007/46/EC” both times it occurs, substitute “Annex IV to Regulation (EU) 2018/858”;

(3) In Appendix 4 to Annex I—

(a) for “EC type-approval”, each time it occurs, substitute “GB type-approval”;

(b) in the first paragraph, in the second and third subparagraphs, omit “and access to vehicle repair and maintenance information”;

(c) in the explanatory notes (regarding filling in the table)—

(i) in the fourth paragraph, for “Parts 1 and 3” substitute “Part 1”;

(ii) in the fifth paragraph—

(aa) for “of vehicle” substitute “of a vehicle”;

(bb) omit “and access to vehicle repair and maintenance information”;

(iii) in the sixth paragraph—

(aa) omit “and access to vehicle repair and maintenance information”;

(bb) for “1, 2 and 3” substitute “1 and 2”;

(d) in the table in following the explanatory notes—

(i) in entry 0.2.0.3, omit “and access to vehicle repair and maintenance information” both times it occurs;

(ii) in entry 0.7, for “EC approval” substitute “GB approval”;

(iii) in the words following the table, omit “Part 3: access to vehicle repair and maintenance information”;

(e) in the table in Part 1, in entry 3.2.12.2.8.2.1—

(i) after “vehicles specified in” insert “point (d) of Article 2(2) or”;

(ii) for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(f) in the table in Part 2, in entry 3.2.12.2.8.2.1—

(i) after “vehicles specified in” insert “point (d) of Article 2(2) or”;

(ii) for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(g) omit Part 3 (access to vehicle repair and maintenance information).

(4) In Appendix 5 to Annex I—

(a) in the heading and each other time it occurs, for “EC type-approval” substitute “GB type-approval”;

(b) in Section I, in point 0.5, for “EC approval” substitute “GB approval”.

(5) In Appendix 6 to Annex I—

(a) in the heading, for “ECT type-approval” substitute “GB type-approval”;

(b) for “EC type-approval”, each time it occurs, substitute “GB type-approval”;

(c) in Section I, in point 0.5, for “EC approval” substitute “GB approval”.

(6) In Appendix 7 to Annex I, in the heading and each other time it appears, including in the Addendum following Appendix 7, for “EC type-approval” substitute “GB type-approval”.

(7) In Appendix 8 to Annex I—

(a) in the heading, for “EC type-approval” substitute “GB type-approval”;

(b) for the image, substitute—

“

”

(c) in the text below the image, omit “in Belgium (e6)”.

(8) In Appendix 9 to Annex I, in the heading and each other time it appears, for “EC type-approval” substitute “GB type-approval”.

(9) In Appendix 10 to Annex I, in note (b), for “Section A of Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(10) In Annex II (conformity of in-service engines or vehicles)—

(a) in point 3.2, at the end of the first sentence, insert “or the United Kingdom”;

(b) in point 4.1, in the second subparagraph, for “Annex I to Directive 2007/46/EC”, substitute “Annex I to Commission Implementing Regulation (EU) 2020/683”;

(c) in point 4.4.2, for “Directive 98/70/EC” substitute “The Motor Fuel (Composition and Content) Regulations 1999”;

(d) in point 9.1, omit “of the Member State where the engines or vehicles subject to remedial action are registered or used”;

(e) in Appendix 1, in point 2.2, omit “and the Commission”.

(11) In Annex VIII (CO₂ emissions and fuel consumption)—

(a) in points 5, and 5.1.1, for “an EC type-approval” substitute “a GB type-approval”;

(b) in point 5.1.2—

(i) for “an EU type-approval” substitute “a GB type-approval”;

(ii) for “existing EU type-approvals” substitute “existing GB type-approvals”.

(12) In Annex X (on-board diagnostics)—

(a) omit point 2.2;

(b) in point 2.4.1, for “Annex I to Directive 2001/85/EC” substitute “Section 2 (Definitions) of UN Regulation 107, as amended by the 07 series of amendments(37)”;

(c) in point 2.4.2, for “EC type-approval”, both times it occurs, substitute “GB type-approval”;

(d) omit point 2.4.4;

(e) in point 2.5, in the first subparagraph, for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(f) in Appendix 5—

(i) in point 2.4.1, in the opening words, omit “and the Commission”;

(ii) in point 5.2.4, for “in the Union” substitute “in Great Britain”;

(iii) in point 6, and in the heading before that point, omit “and the Commission”.

(13) In Annex XI (EC type-approval of replacement pollution control devices as separate technical units)—

(a) in the heading, for “EC” substitute “GB”;

(b) each time it occurs (including in the Appendices)—

(i) for “an EC type-approval” substitute “a GB type-approval”;

(ii) for “the EC type-approval” substitute “the GB type-approval”;

(c) in point 3, for “date EC” substitute “date GB”;

(d) for point 3.2—

(i) for the first subparagraph, substitute—

“3.2.   A rectangle surrounding the lower-case letter ‘g’ followed by the number 11.”;

(ii) in the second subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(e) in point 4.1.4, omit “that granted the original type-approval of the engine system”;

(f) in point 4.5.4—

(i) omit “which granted original type-approval of an engine of a vehicle”;

(ii) omit “Appendix on test conditions to Appendix 4 to Annex I, which contains”;

(g) in point 4.6.4, omit “which granted original type-approval of an engine of a vehicle”;

(h) in point 5.1, for “Article 12 of Directive 2007/46/EC” substitute “Article 31 of Regulation (EU) 2018/858”;

(i) in point 5.2.1, for “Section 2.2 of Annex X to Directive 2007/46/EC” substitute “Section 3.2 of Annex IV to Regulation (EU) 2018/858”;

(j) in point 5.2.2, for “Article 12(2) of Directive 2007/46/EC” substitute “Article 31(3) of Regulation (EU) 2018/858”;

(k) in Appendix 1—

(i) in point 0.7, for “EC approval” substitute “GB approval”;

(ii) omit points 2 to 2.3;

(l) in Appendix 2—

(i) for “EC type-approval” each time it occurs, substitute “GB type-approval”;

(ii) in the opening Section, after “last amended by” insert “S.I. …./….”;

(iii) in Section I, in point 0.7, for “EC approval” substitute “GB approval”;

(m) in Appendix 3—

(i) in point 2.4.2.11, for “Article 3(25) of Directive 2007/46/EC” substitute “Article 2(20) of Regulation (EU) 2018/858”;

(ii) in point 2.4.6.5, for “Directive 98/70/EC” substitute “the Motor Fuel (Composition and Content) Regulations 1999”.

(14) In Annex XIII (requirements to ensure the correct operation of NO_x control measures)—

(a) in point 2.1.1, for “Annex I to Directive 2001/85/EC” substitute “Section 2 (Definitions) in UN Regulation 107, as amended by the 07 series of amendments(38)”;

(b) in point 2.1.2.2.5—

(i) after “specified in” insert “Article 2(2)(d) or”;

(ii) for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(c) in point 2.1.5, in the modified text, after “the Union” insert “or the United Kingdom”;

(d) in point 4.1.1 and 5.1.1, in the modified text, for “point (b) of Article 2(3) of Directive 2007/46/EC” substitute “Article 2(2)(d) or 2(3)(b) of Regulation (EU) 2018/858”;

(e) in point 12, in the second subparagraph—

(i) for “EC type-approval” substitute “GB type-approval”;

(ii) omit “and access to vehicle repair and maintenance information”.

(15) Omit Annex XVII (access to vehicle OBD and vehicle repair and maintenance information).

(16) In Annex XVIII (specific technical requirements for dual-fuel engines and vehicles), in point 7.2, for “an EC” substitute “a GB”.

Commission Regulation (EU) No 65/2012

67.—(1) Commission Regulation (EU) No 65/2012 is amended as follows.

(2) In Article 4 (EC type-approval)—

(a) in the heading, for “EC type-approval” substitute “GB type-approval”;

(b) in the opening words of paragraph 2 and in the second sub-paragraph of paragraph 3, for “an EC type-approval” substitute “a GB type-approval”.

(3) Omit Article 5 (monitoring the effects of legislation).

(4) After Article 7 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”

(5) In Annex II—

(a) in Part 1 (information document)—

(i) in the first paragraph, for “EC type-approval” substitute “GB type-approval”;

(ii) in the fourth paragraph, for “Regulation (EC) No 692/2008:” substitute “Regulation (EU) No 2017/1151;”;

(b) in Part 3 (EC type-approval certificate)—

(i) in the heading and each time it occurs, for “EC type-approval” substitute “GB type-approval”;

(ii) for “Regulation (EU) No 65/2012 as last amended by Regulation (EU) No …/…” substitute “Regulation (EU) No 65/2012, as it has effect in domestic law, and as last amended by S.I. …../……”.

Commission Regulation (EU) No 130/2012

68.—(1) Commission Regulation (EU) No 130/2012 is amended as follows.

(2) In Article 1 (scope), for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(3) In Article 2(2) (definitions), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”.

(4) In Article 3 (EC type-approval of vehicles re vehicle access and manoeuvrability)—

(a) in the heading, and in paragraph 1, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraph 3—

(i) for “an EC type-approval” substitute “a GB type-approval”;

(ii) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(iii) for “A Member State” substitute “The approval authority”;

(c) in paragraph 4, for “an EC type-approval” substitute “a GB type-approval”.

(5) In Article 4 (validity and extension of approvals granted under Directive 70/387/EEC and Directive 75/443/EEC)—

(a) omit “National authorities shall permit”;

(b) for “661/2009 and” substitute “661/2009 is permitted, and the approval authority must”;

(6) After Article 5 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”

(7) In Annex I (administrative provisions for type-approval of vehicles re vehicle access and manoeuvrability)—

(a) in Part 1 (information document)—

(i) in the first paragraph, for “EC type-approval” substitute “GB type-approval”;

(ii) in the explanatory notes following Part 1, in note (^c) to point 0.4, for “for “Part A of Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(b) in Part 2 (EC type-approval certificate)—

(i) in the heading and each time it occurs, for “EC type-approval” substitute “GB type-approval”;

(ii) in the opening section, for “as last amended by Regulation (EU) No …/…” substitute “as it has effect in domestic law, and as last amended by S.I. …./…”;

(iii) in the explanatory notes following Part 2, in note (³) to point 0.4, for “Directive 2007/46/EC, Annex II, Section A”, substitute “Article 4 of Regulation (EU) 2018/858”;

(c) in the heading to the addendum to Part 2, for “EC” substitute “GB”.

Commission Regulation (EU) No 347/2012

69.—(1) Commission Regulation (EU) No 347/2012 is amended as follows.

(2) In Article 1 (scope)—

(a) in the opening words, for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(b) in points (4) and (5), for “Part A of Annex II to Directive 2007/46/EC” substitute “Part A of Annex I to Regulation (EU) 2018/858”.

(3) In Article 2 (definitions)—

(a) in the first paragraph, for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(b) in the second paragraph, in point (3), for “point 1 of Section C of Annex II to Directive 2007/46/EC” substitute “point 2.1 of Part C of Annex I to Regulation (EU) 2018/858”.

(4) In Article 3 (obligations of member States)—

(a) in the heading, for “Member States” substitute “Secretary of State”;

(b) omit paragraphs 1 and 2;

(c) in paragraph 3—

(i) for “national authorities” substitute “the approval authority”;

(ii) for “EC” substitute “GB”;

(iii) omit “or national type approval”;

(d) in paragraph 4—

(i) for “national authorities” substitute “the Secretary of State”;

(ii) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(e) in paragraph 5—

(i) in the opening words, for “national authorities” substitute “the Secretary of State”;

(ii) in points (a) and (c)—

(aa) for “EC type-approval” substitute “GB type-approval”;

(bb) omit “or national type approval”.

(5) In Article 4 (EC type-approval of a vehicle re AEBS)—

(a) in the heading, and in paragraph 1, for “EC” substitute “GB”;

(b) in paragraph 3—

(i) for “an EC” substitute “a GB”;

(ii) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Regulation (EU) 2020/683”;

(iii) for “An approval authority” substitute “The approval authority”.

(c) in paragraph 4, for “an EC” substitute “a GB”.

(6) Omit Article 5 (amendment to Appendix 2 of Annex II).

(7) After Article 6 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States”.

(8) In Annex I (standard information document and EC type-approval certificate re AEBS)—

(a) in the heading, for “EC” substitute “GB”;

(b) in Part 1 (information document)—

(i) in the first paragraph, for “EC” substitute “GB”;

(ii) in point 8.1, for “point 1.6 of Annex I to the Council Directive 71/320/EEC” substitute “point 2.6 of UNECE Regulation No 13(39)”;

(iii) in point 8.2, for “point “1.2 of Annex I to Directive 71/320/EEC” substitute “point 2.3 of UNECE Regulation No 13”;

(iv) in point 8.6, for “the Appendix to point 1.1.4.2 of the Appendix to Annex II to Directive 71/320/EEC or to the Appendix to Annex XI thereto” substitute “Annex 10 to UNECE Regulation No 13 or to Annex 14 to that Regulation”;

(c) in the explanatory notes following Part 1—

(i) in note (^c), for “Part A of Annex II to Directive 2007/46/EC of the European Parliament and of the Council (OJ L 263, 9.10.2007, p.1)” substitute “Article 4 of Regulation (EU) 2018/858”;

(ii) in footnote (^g5), for “point 2.4.1 of Annex I to Directive 97/27/EC of the European Parliament and of the Council (OJ L 233, 25.8.1997, p.1)” substitute “point 22 of Article 2 of Commission Regulation (EU) 1230/2012, taking into account Appendix 1 to Annex I thereto”;

(iii) in footnote (^g7), for “point 2.4.2 of Annex I to Directive 97/27/EC” substitute “point 23 of Article 2 of Commission Regulation 1230/2012, taking into account Appendix 1 to Annex I thereto”;

(d) in Part 2 (model EC type-approval certificate)—

(i) in the certificate heading, for “EC type-approval” substitute “GB type-approval”;

(ii) in words preceding Section I—

(aa) for “EC type-approval” each time it occurs, substitute “GB type-approval”;

(bb) for “as amended and complying with approval level 1 / approval level 2” substitute “as it forms part of domestic law and as lasted amended by S.I. …../… with approval level 2”;

(e) in the explanatory notes following Part 2, in note (³), for “Section A of Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(f) in the Addendum to Part 2, in the heading, for “EC” substitute “GB”.

(9) In Annex II (requirements and tests for the type-approval of vehicles re AEBS)—

(a) in point 2.4.2.1, omit subparagraph (a);

(b) in point 2.4.2.2, omit the words “for approval level 1” to “Appendix 1”;

(c) in point 2.4.5, omit “For approval level 1: Column D of the table in Appendix 1”;

(d) in point 2.5.1, omit “For approval level 1: Column H of the table in Appendix 1”;

(e) in point 2.5.2.1, omit “For approval level 1: Column E of the table in Appendix 1”;

(f) in point 2.5.2.2, omit “For approval level 1: Column F of the table in Appendix 1”;

(g) omit Appendix 1 to Annex II;

(h) in the footnotes to Appendix 2, omit footnote (⁵).

Commission Regulation (EU) No 351/2012

70.—(1) Commission Regulation (EU) No 351/2012 is amended as follows—

(2) In Article 1 (scope)—

(a) in the opening words, for “Annex II to Directive 2007/46/EC of the European Parliament and of the Council” substitute “Article 4 of Regulation (EU) 2018/858”;

(b) in point 4, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(c) in point 5, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”.

(3) In Article 3 (EC type-approval of a type of vehicle re LDWS)—

(a) in the heading, and in paragraph 1, for “EC” substitute “GB”;

(b) in paragraph 3—

(i) in the first subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”;

(c) in paragraphs 3 and 4, for “an EC” substitute “a GB”;

(d) after paragraph 4, insert—

“5.   Where an application for approval is made before 31st December 2026 under paragraph 1 in respect of a vehicle type which has been approved by the approval authority of a member State under Commission Regulation (EU) 351/2012, as that Regulation has effect in EU law, by way of derogation to point 2.2.3.1 of Annex II to this Regulation, the visible lane markings used in the lane departure tests of point 2.6 may be any one of those identified in the Appendix to Annex II, provided that the approval authority has been presented with documentary evidence in accordance with point 2.2.3.2 of Annex II demonstrating compliance with the UK lane markings specified in table 1 in the Appendix to Annex II.”.

(4) After Article 4 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States”.

(5) In Annex I (standard models for the information document and EC type-approval certificate)—

(a) in the heading and each time it appears, for “EC” substitute “GB”;

(b) in the explanatory notes following Part 1—

(i) in note (^c), for “Part A of Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(ii) in note (^g5), for “point 2.4.1 of Annex I to Directive 97/27/EC of the European Parliament and of the Council” substitute “point 22 of Article 2 of Commission Regulation (EU) 1230/2012, taking into account Appendix 1 to Annex I”;

(iii) in note (^g7), for “point 2.4.2 of Annex I to Directive 97/27/EC” substitute “point 23 of Article 2 of Commission Regulation (EU) 1230/2012, taking into account Appendix 1 to Annex I”;

(c) in Part 2, for “as amended” substitute “as it forms part of domestic law, and as last amended by S.I. …./….”;

(d) in the explanatory notes following Part 2, in note (³), for “Section A of Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(e) in the heading to the Addendum to Annex I, for “EC” substitute “GB”.

(6) In Annex II (requirements and tests for the type-approval of motor vehicles re lane departure warnings systems)—

(a) in point 2.2.3.1—

(i) after “to this Annex” insert “as being used in the United Kingdom”;

(ii) for “Member State concerned” substitute “United Kingdom”;

(b) in point 2.2.3.2, after “to this Annex” insert “as being used in the United Kingdom”.

Commission Regulation (EU) No 1230/2012: Articles

71.—(1) Commission Regulation (EU) No 1230/2012 is amended as follows.

(2) In Article 1 (subject matter and scope), in paragraph 1, for “EC type-approval” substitute “GB type-approval”.

(3) In Article 2 (definitions)—

(a) in the opening words, for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(b) in point (1), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(c) in point (2) for “Annex IV and Annex XI to Directive 2007/46/EC” substitute “Annex II to Regulation (EU) 2018/858”;

(d) in point (11), for the words “a number of axles” to the end, substitute “a tandem axle, or a triaxle, as defined in each case in regulation 2 of the Road Vehicles (Authorised Weight) Regulations 1998(40)”;

(e) in point (40), for “applicable in a Member State” substitute “set out in regulation 4 of the Road Vehicles (Authorised Weight) Regulations 1998 and regulations 7 and 8 of the Road Vehicles (Construction and Use) Regulations 1986(41), read for these purposes as if they did not include regulation 7(3A)(a)”.

(4) In Article 4 (EC type-approval of a type of vehicle re masses and dimensions)—

(a) in the heading, and in paragraphs 1 and 8 for “EC type-approval” substitute “GB type-approval”;

(b) in paragraph 9—

(i) in the first subparagraph—

(aa) after “grant a” insert “GB”;

(bb) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”;

(c) in paragraph 10, for “an EC type-approval” substitute “a GB type-approval”;

(d) in paragraph 11, for “Article 12(2) of Directive 2007/46/EC” substitute “Article 31(3) and (4) of Regulation (EU) 2018/858”.

(5) In Article 4a (EC separate technical unit type-approval of aerodynamic devices and equipment)—

(a) in the heading, for “EC” substitute “GB”;

(b) in paragraph 1, for “EC type-approval” substitute “GB type-approval”;

(c) in paragraph 2—

(i) for “an EC” substitute “a GB”;

(ii) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(iii) for “A Member State” substitute “The approval authority”;

(d) in paragraph 3, for “an EC” substitute “a GB”.

(6) In Article 4b (EC separate technical unit type-approval mark)—

(a) in the heading, and the first time it occurs, for “EC” substitute “GB”;

(b) for “an EC” substitute “a GB”.

(7) Omit Article 5 (registration/in-service maximum permissible masses).

(8) In Article 6 (derogations)—

(a) for paragraph 1, substitute—

“1.   Without prejudice to Article 9 of the Road Vehicles (Authorisation of Special Types) (General) Order 2003(42), a GB type-approval may be granted for—

(a) motor vehicles, the width of which exceeds the requirements of this Regulation, or

(b) trailers, the length or width of which exceeds the requirements of this Regulation,

where the vehicle or trailer is intended for the transport of indivisible loads.

1a.   Where paragraph 1 applies, the type approval certificate and the certificate of conformity must indicate clearly that the vehicle, or trailer, as appropriate, is intended only for the transport of indivisible loads.”;

(b) in paragraph 2—

(i) for “Member States” substitute “The approval authority”;

(ii) for “Articles 23 and 24 of Directive 2007/46/EC” substitute “Articles 42 and 45 of Regulation (EU) 2018/858”;

(iii) omit the second subparagraph.

(9) In Article 7 (transitional provisions), omit paragraph 2, and the second subparagraph of paragraph 3.

(10) After Article 9 (entry into force), omit the words “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.

Commission Regulation (EU) No 1230/2012: Annexes

72.—(1) The Annexes to Commission Regulation (EU) No 1230/2012 are amended as follows.

(2) In Annex I (technical requirements)—

(a) in Part A (vehicles of category M₁ and N₁)—

(i) in point 1.1.2(c), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(ii) omit point 1.1.3;

(iii) in points 1.2 and 1.3, for “length, width and height”, each time these words occur, substitute “length and width”;

(iv) omit point 2.7.2.2;

(v) in point 3.1.1.1(c), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(b) in Part B—

(i) in point 1.1.3, for “4,00 m” substitute “4.57 m”;

(ii) in point 2.1.3.1, for “The additional weight required for alternative fuel or zero-emission technology in accordance with points 2.3. and 2.4. of Annex I to Directive 96/53/EC shall be defined” substitute “Any increase in the maximum authorised weight of a vehicle that is permitted for alternative fuel or zero-emission technology in accordance with regulation 4 of the Road Vehicles (Authorised Weight) Regulations 1998(43) must be determined”;

(iii) in point 2.1.3.2—

(aa) for “the following additional symbol” substitute “one or both of the following additional symbols”;

(bb) for “additional weight” both times it occurs, substitute “increase in weight”;

(cc) at the end of the second subparagraph, insert “, or”;

(dd) after the second subparagraph, insert—

“‘AWR REGULATION 4 COMPLIANT – XXXX KG’”;

(iv) in point 7.4, for “Annex XVI to Directive 2007/46/EC” substitute “Annex VIII to Regulation (EU) 2018/858”;

(v) in point 8.3, for “Annex XVI to Directive 2007/46/EC” substitute “Annex VIII to Regulation (EU) 2018/858”;

(c) in Part C—

(i) in point 1.1.2(b), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(ii) omit point 1.1.3;

(iii) in points 1.2 and 1.3. for “length, width and height” each time those words occur, substitute “length and width”;

(iv) in point 1.4.2—

(aa) for “the following additional symbol” substitute “one or both of the following additional symbols”;

(bb) at the end of the second subparagraph, insert “, or”;

(cc) after the second subparagraph, insert—

“‘C&U REGULATION 7(3D) COMPLIANT’”;

(dd) for “text ‘96/53/EC ARTICLE 9A COMPLIANT’” substitute “symbols above”;

(v) in point 2.1.4.1, for “The additional weight required for alternative fuel or zero-emission technology in accordance with point 2.3. of Annex I to Directive 96/53/EC shall be defined” substitute “Any increase in the maximum authorised weight of a vehicle that is permitted for alternative fuel or zero-emission technology in accordance with regulation 4 of the Road Vehicles (Authorised Weight) Regulations 1998 must be determined”;

(vi) in point 2.1.4.2—

(aa) for “the following additional symbol” substitute “one or both of the following additional symbols”;

(bb) for “additional weight”, both times it occurs, substitute “increase in weight”;

(cc) after “XXXX KG”, on a new line insert—

“or

• ‘AWR REGULATION 4 COMPLIANT – XXXX KG’”;

(vii) in point 4.2.1, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(viii) in point 6.4, for “Annex XVI to Directive 2007/46/EC” substitute “Annex VIII to Regulation (EU) 2018/858”;

(ix) in point 7.3, for “Annex XVI to Directive 2007/46/EC” substitute “Annex VIII to Regulation (EU) 2018/858”;

(d) in Part D—

(i) in point 1.1.2, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(ii) omit point 1.1.3;

(iii) in points 1.2 and 1.4, for “length, width and height”, in each place those words occur, substitute “length and width”;

(iv) in point 1.3, omit “, height”;

(e) in Appendix 2 to Annex I—

(i) in point 2.1, for “Directive 2009/23/EC of the European Parliament and of the Council” substitute “the Non-automatic Weighing Instruments Regulations 2016(44)”;

(ii) in point 2.2—

(aa) in the opening words, for “Annex III to Directive 2007/46/EC” substitute “Annex II to Commission Implementing Regulation (EU) 2020/683”;

(bb) in subparagraph (c), for “Article 12(2) of Directive 2007/46/EC” substitute “Article 31(3) and (4) of Regulation (EU) 2018/858”;

(f) in Appendix 4 to Annex I, in point 1.3, for “Annex XVI to Directive 2007/46/EC” substitute “Annex VIII to Regulation (EU) 2018/858”.

(3) In Annex II (gradeability of off-road vehicles)—

(a) in point 1.1, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(b) in point 1.2, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(c) in point 2.1.1, for “Annex I to Directive 2007/46/EC” substitute “Annex I to Commission Implementing Regulation (EU) 2020/683”;

(d) in point 3.3, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”.

(4) In Annex V—

(a) in the heading to Part A, for “EC” substitute “GB”;

(b) in Part A (information document: vehicles and their trailers: masses and dimensions)—

(i) in the opening paragraph, for “EC type-approval” substitute “GB type-approval”;

(ii) in point 2.4.2.1.3, for “Article 9a of Directive 96/53/EC” substitute “point 1.4 of Part C of Annex I to Commission Regulation (EU) No 2012/1230”;

(iii) in point 2.4.2.6, for “points 3.1.1 and 3.2.1 of Appendix 1 to Annex II to Directive 2007/46/EC” substitute “points 4.1 and 4.2 of Part A of Annex I to Regulation (EU) 2018/858”;

(iv) in point 2.6.4, for “Additional weight” substitute “Increase in mass”;

(v) renumber point 2.11.4.1 as point 2.11.3.1, and move that point to follow point 2.11.3;

(vi) renumber point 2.11.4.2 as point 2.11.3.2, and move that point to follow point 2.11.3.1;

(vii) in point 9.1, for “Annex II” substitute “Annex I to Regulation (EU) 2018/858”;

(viii) in point 9.25, for “Article 9a of Directive 96/53/EC” substitute “point 1.4 of Part C of Annex I to Commission Regulation 2012/1230”;

(ix) in the Explanatory notes to the information document—

(aa) in note (^c), for “Part A of Annex II” substitute “Article 4 of Regulation (EU) 2018/858”;

(bb) for note (^e) substitute—

“(e) ‘Forward control’ means a configuration in which more than half of the engine length is rearward of the foremost point of the windshield base and the steering wheel hub in the forward quarter of the vehicle length as defined in the explanatory note (z) of Appendix 1 of Part 1 of Annex 1 to UN Regulation No 107, as amended by the 07 series of amendments(45).”;

(cc) in note (ⁿ), for “Council Directive 80/1269/EEC” substitute “Regulation (EC) No 715/2007 or Regulation (EC) No 595/2009 as applicable”;

(dd) in note (^o), for “Council Directive 80/1268/EEC” substitute “Regulation (EC) No 715/2007”;

(ee) in note (^t), for “Annex III to Directive 77/649/EEC” substitute “Annex III to UN Regulation No 17, as amended by the 08 series of amendments(46)”;

(c) in Part B (EC type-approval certificates: vehicles and their trailers, masses and dimensions)—

(i) in the heading, and each time it appears, for “EC type-approval” substitute “GB type-approval”;

(ii) for the words from “Communication concerning” to “reason for extension” substitute—

“Communication concerning granting / extension / refusal / withdrawal (⁷) of type-approval of a type of vehicle with regard to its masses and dimensions in accordance with the requirements laid down in Commission Regulation (EU) 2012/1230 as it has effect in domestic law, as last amended by SI_____/_____.

Number of the GB type-approval certificate:

Reason for extension / refusal / withdrawal (¹):”;

(iii) in Section I, for points 0.1 to 0.9, substitute—

“(to be completed in accordance with Section I of the template of Model B in Annex III to Commission Implementing Regulation (EU) 2020/683)”;

(iv) in Section II, for points 1 to 8 and the following list of attachments, substitute—

“(to be completed in accordance with Section II of the template of Model B in Annex III to Commission Implementing Regulation (EU) 2020/683)”;

(v) in the Addendum—

(aa) in the heading, for “EC type-approval” substitute “GB type-approval”;

(bb) in point 1, for “Derogations” substitute “Additional information”;

(cc) in point 1.1, after “6(1)” insert “or 6(2)”;

(dd) after point 1.1, insert—

“1.1.1.   Vehicle intended for transport of indivisible loads only: yes / no”;

(ee) for points 1.2 and 1.3, substitute—

“1.2.   The vehicle has been type-approved in accordance with paragraphs 1.3.1.1 or 1.3.1.2 of Part C of Annex I to Commission Regulation (EU) 2012/1230 (i.e. aerodynamic devices or equipment at the rear of the vehicle): yes / no:

1.3.   The vehicle has been type-approved in accordance with paragraphs 1.3.1.3 or 1.4 of Part C of Annex I to Commission Regulation (EU) 2012/1230 (i.e. a cab fitted with aerodynamic devices or equipment or an elongated cab): yes / no:”;

(ff) in point 1.4, for “for the purposes of Article 10b of Directive 96/53/EC” substitute “in accordance with Regulation 4 of the Road Vehicles (Authorised Weight) Regulations 1998”;

(gg) in points 1.4.1 and 1.4.2, for “Additional weight” substitute “increase in weight”;

(d) in Part C (information document: aerodynamic device or equipment as separate technical unit), in the heading, and each time it occurs, for “EC type-approval” substitute “GB type-approval”;

(e) in Part D (EC type-approval certificate: aerodynamic device or equipment as separate technical unit)—

(i) for “EC type-approval certificate”, in the heading and each other time it occurs (including in the Addendum), substitute “GB type-approval certificate”;

(ii) for the words from “Communication concerning” to “reason for extension” substitute—

“Communication concerning granting / extension / refusal / withdrawal of type-approval of a type of an aerodynamic device or equipment as a separate technical unit in accordance with the requirements laid down in Commission Regulation (EU) 2012/1230 as it has effect in domestic law, as last amended by SI…./…….

Number of the GB type-approval certificate:

Reason for extension / refusal / withdrawal (¹):”

(iii) in Section I, for points 0.1 to 0.9 substitute—

“(to be completed in accordance with Section I of the template of Model C in Annex III to Commission Implementing Regulation (EU) 2020/683)”;

(iv) in Section II, for points 1 to 8 and the following list of attachments substitute—

“(to be completed in accordance with Section II of the template of Model C in Annex III to Commission Implementing Regulation (EU) 2020/683)”;

(f) in Part E (EC separate technical unit type-approval mark)—

(i) in the heading, and each other time it occurs, for “EC separate” substitute “GB separate”;

(ii) in the heading, at the end, insert “for an aerodynamic device or equipment”;

(iii) for point 1.1, substitute—

“1.1.   A rectangle surrounding the lower-case letter ‘g’ followed by the distinguishing number 11.”;

(iv) in point 1.3, after “‘96/53/EC ARTICLE 9A COMPLIANT’”, insert “or the symbol REG 1230/2012, PARA 1.3.1.3 of PART C of ANNEX I COMPLIANT”;

(v) in point 1.4, after “‘96/53/EC ARTICLE 8B COMPLIANT’”, insert “or either of the symbols “REG 1230/2012, PARA 1.3.1.1 of PART C of ANNEX I COMPLIANT” or “REG 1230/2012, PARA 1.3.1.2 of PART C of ANNEX I COMPLIANT” as appropriate”;

(vi) in point 3, for “an EC” substitute “a GB”;

(vii) for figure 1, substitute—

“

”;

(viii) in the explanatory note—

(aa) omit the words “(for the purpose of compliance with Article 8b of Directive 96/53/EC)”;

(bb) omit “by Romania”.

Regulation (EU) No 167/2013

73.—(1) Regulation (EU) No 167/2013 is amended as follows.

(2) In Article 40 (making available on the market or entry into service: components and separate technical units)—

(a) in paragraph 1, for the words after “service” to the end, substitute “if paragraph 1A applies to the components or separate technical units”;

(b) after paragraph 1, insert—

“1A.   This paragraph applies to components or separate technical units if they—

(a) comply with the requirements of the relevant regulatory acts listed in Annex I and are properly marked in accordance with Article 34;

(b) comply with the requirements of the relevant regulatory acts listed in Annex I to Regulation (EU) No 167/2013(47) as it has effect in EU law, provided that the component or separate technical unit—

(i) has approval under section 55(1A) or (1D) of the Road Traffic Act 1988(48),

(ii) was in the United Kingdom before 1st January 2023, or

(iii) is a qualifying Northern Ireland good; or

(c) comply with the requirements of the relevant regulatory acts listed in Annex I to Regulation (EU) No 167/2013 as it has effect by virtue of the Protocol on Ireland/Northern Ireland in the EU Withdrawal Agreement, provided that—

(i) they are properly marked in accordance with Article 34 of that Regulation, and

(ii) they have approval under that Regulation from the Secretary of State.”;

(c) after paragraph 4, insert—

“5.   By way of derogation from paragraph 1, replacement components and separate technical units that were EU type-approved before 1st January 2023 in accordance with the requirements listed in Annex I to Regulation (EU) No 167/2013 as it has effect in EU law may be made available on the market or entered into service.”.

Regulation (EU) No 168/2013

74.—(1) Regulation (EU) No 168/2013 is amended as follows.

(2) In Article 45 (making available on the market or entry into service: components and separate technical units)—

(a) in paragraph 1, for the words after “service” to the end, substitute “if paragraph 1A applies to the components or separate technical units”;

(b) after paragraph 1, insert—

“1A.   This paragraph applies to components or separate technical units if they—

(a) comply with the requirements of the relevant regulatory acts listed in Annex II and are properly marked in accordance with Article 39;

(b) comply with the requirements of the relevant regulatory acts listed in Annex II to Regulation (EU) No 168/2013(49) as it has effect in EU law, provided that the component or separate technical unit—

(i) has approval under section 55(1A) or (1D) of the Road Traffic Act 1988(50),

(ii) was in the United Kingdom before 1st January 2023, or

(iii) is a qualifying Northern Ireland good; or

(c) comply with the requirements of the relevant regulatory acts listed in Annex II to Regulation (EU) No 168/2013 as it has effect by virtue of the Protocol on Ireland/Northern Ireland in the EU Withdrawal Agreement, provided that—

(i) they are properly marked in accordance with Article 39 of that Regulation, and

(ii) have approval under that Regulation from the Secretary of State.”;

(c) after paragraph 4, insert—

“5.   By way of derogation from paragraph 1, replacement components and separate technical units that were EU type-approved before 1st January 2023 in accordance with the requirements listed in Annex I to Regulation (EU) No 168/2013 as it has effect in EU law may be made available on the market or entered into service.”.

Regulation (EU) No 540/2014: Articles

75.—(1) Regulation (EU) No 540/2014 is amended as follows.

(2) In Article 1 (subject matter)—

(a) for “EU” substitute “GB”;

(b) for “the Union” substitute “Great Britain”.

(3) In Article 2 (scope), for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”.

(4) In Article 3 (definitions)—

(a) in the opening words, for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(b) in point (1), for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(c) in point (5), for “Annex IV or Annex XI to Directive 2007/46/EC” substitute “Annex II to Regulation (EU) 2018/858”;

(d) in point (21), for “EU” substitute “GB”.

(5) In Article 4 (general obligations of member States)—

(a) in the heading, for “Member States” substitute “the Secretary of State”;

(b) for “EU type-approval” each time it appears, substitute “GB type-approval”;

(c) in paragraph 1—

(i) for “Article 23 of Directive 2007/46/EC” substitute “Article 42 of Regulation (EU) 2018/858”;

(ii) for “Member States” substitute “the approval authority”;

(d) in paragraph 2—

(i) in the first sub-paragraph, for “Member States” substitute “the approval authority”;

(ii) for the second sub-paragraph, substitute—

“The approval authority may grant GB type-approval, under the terms and test procedures of Annex II of Directive 70/157/EEC(51) as it had effect in EU law on IP completion date, to a replacement silencing system, or components thereof, as a separate technical unit intended for vehicles type-approved before the dates of phases of application set out in Annex III to this Regulation.”;

(e) in paragraph 3—

(i) for “Member States” substitute “the Secretary of State”;

(ii) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(f) in paragraph 4—

(i) for “Member States” both times it occurs, substitute “the Secretary of State”;

(ii) in the second sub-paragraph, for the words from “holding” to the end, substitute—

“holding an EU type-approval as a separate technical unit under the terms of Annex II to Directive 70/157/EEC issued by—

(a) the Secretary of State before IP completion day, or

(b) an approval authority of a member State before 1st January 2023.”.

(6) In Article 7 (consumer information and labelling), omit the second subparagraph.

(7) In Article 8 (acoustic vehicle alerting system), for the second subparagraph substitute—

“The Secretary of State may by regulations amend Annex VIII to include more detailed requirements on the performance of AVAS or of active safety systems, taking into account the UNECE work on that issue.”.

(8) For Articles 9 (amendment of the annexes) and 10 (exercise of the delegation), substitute—

“Article 9 Amendment of the annexes

The Secretary of State may by regulations amend Annexes I, IV, VIII and X to take account of technical developments.

Article 10 Regulations

1.   Any power to make regulations conferred on the Secretary of State by this Regulation is exercisable by statutory instrument.

2.   Such regulations may—

(a) make incidental, supplemental, consequential or transitional provision, and

(b) make different provision for different cases or descriptions of case, different circumstances, different purposes or different areas.

3.   Before making any regulations under this Regulation the Secretary of State must consult with such representative organisations as the Secretary of State thinks fit.

4.   A statutory instrument containing regulations made under this Regulation is subject to annulment in pursuance of a resolution of either House of Parliament.”.

(9) Omit Article 11 (revision clause).

(10) After Article 15 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.

Regulation (EU) No 540/2014: Annexes

76.—(1) The Annexes to Regulation (EU) No 540/2014 are amended as follows.

(2) In Annex I (EU type-approval: sound level of a vehicle type)—

(a) in the heading, and each other time it occurs, including in the Appendices to the Annex I, for “EU type-approval” substitute “GB type-approval”;

(b) in point 1.1, for “Article 7(1) and (2) of Directive 2007/46/EC” substitute “Article 23 of Regulation (EU) 2018/858”;

(c) in point 3.1, for “Article 9(3) and, if applicable, Article 10(4) of Directive 2007/46/EC” substitute “Article 28(4) and, if applicable, Article 29(3) of Regulation (EU) 2018/858”;

(d) in point 3.3—

(i) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) for “The same Member State” substitute “The approval authority”;

(e) in point 4, for “Articles 13, 14, 15, 16 and Article 17(4) of Directive 2007/46/EC” substitute “Articles 33, 34 and 35 of Regulation (EU) 2018/858”;

(f) in point 5.1, for “Article 12 of Directive 2007/46/EC” substitute “Article 31 of Regulation (EU) 2018/858”;

(g) in point 5.2.1, for “point 2.3.5 of Annex X to Directive 2007/46/EC” substitute “point 3.3.5 of Annex IV of Regulation (EU) 2018/858”;

(h) in point 5.2.2, for “point 3 of Annex X to Directive 2007/46/EC” substitute “point 4 of Annex IV to Regulation (EU) 2018/858”;

(i) in Appendix 1—

(i) in the heading, for “Annex I of Directive 2007/46/EC” substitute “Annex I to Commission Implementing Regulation (EU) 2020/683”;

(ii) in point 9(1), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(j) in Appendix 2—

(i) in the heading for “EU” substitute “GB”;

(ii) in the words before Section 1, after “540/2014” insert “as it has effect in domestic law”;

(k) in the notes following Appendix 2—

(i) in note 1, for “point 4 of Part A of Annex II to Directive 2007/46/EC” substitute “point 2.1 of Part A of Annex I to Regulation (EU) 2018/858”;

(ii) in note 3, for “Annex IIA to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(l) in the Addendum following Appendix 2, in the heading, for “EU” substitute “GB”.

(3) In Annex II (methods and instruments for measuring noise made by motor vehicles), for “EU type-approval” both times it occurs, substitute “GB type-approval”.

(4) In Annex III (limit values)—

(a) in the first note after the table, for “point 4 of Part A of Annex II to Directive 2007/46/EC” substitute “point 2.1 of Part A of Annex I to Regulation (EU) 2018/858”;

(b) in the final note after the table, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”.

(5) In Annex IV (silencing systems containing acoustically absorbing fibrous materials), in section 1, in point (b) of the first paragraph, for “EU type-approval” substitute “a GB type approval”.

(6) In Annex VI (checks on conformity of production for vehicles), in section 3, for “Annex X to Directive 2007/46/EC” each time it occurs, substitute “Annex IV to Regulation (EU) 2018/858”.

(7) In Annex VII (measuring method to evaluate compliance with additional sound emission provisions), in the second paragraph of section 1, for “EU type-approval” substitute “GB type-approval”.

(8) In Annex VIII (measures concerning the acoustic vehicle alerting system), in section III.5, for “EU type-approval” substitute “GB type-approval”.

(9) In Annex IX (EU type-approval: sound level of silencing systems as separate technical units)—

(a) in the heading and each other time it occurs, including in the Appendices to Annex IX, for “EU type-approval” substitute “GB type-approval”;

(b) in point 1.1 for “Article 7(1) and (2) of Directive 2007/46/EC” substitute “Article 23 of Regulation (EU) 2018/858”;

(c) in point 3.1, for “Article 9(3) and, if applicable, Article 10(4) of Directive 2007/46/EC” substitute “Article 28(4) and, if applicable, Article 29(3) of Regulation (EU) 2018/858”;

(d) in point 3.3—

(i) in the first sentence, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the last sentence, for “same Member State” substitute “approval authority”;

(e) in point 4.2—

(i) for the first subparagraph, substitute—

“4.2.   The GB type-approval mark consists of a rectangle surrounding the lower-case letter “g” followed by number “11”.”;

(ii) in the second subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV of Commission Implementing Regulation (EU) 2020/683”;

(f) in point 6, in the second subparagraph, omit the second sentence;

(g) in point 7, for “Articles 13 to 16 and Article 17(4) of Directive 2007/46/EC” substitute “Articles 33, 34 and 35(5) of Regulation (EU) 2018/858”;

(h) in point 8.1, for “Article 12 of Directive 2007/46/EC” substitute “Article 31 of Regulation (EU) 2018/858”;

(i) in point 8.2.1, for “point 2.3.5 of Annex X to Directive 2007/46/EC” substitute “point 3.3.5 of Annex IV of Regulation (EU) 2018/858”;

(j) in point 8.2.2, for “point 3 of Annex X to Directive 2007/46/EC” substitute “point 4 of Annex IV to Regulation (EU) 2018/858”;

(k) in Appendix 1, in point 1.5, for “EU” substitute “GB”;

(l) in the Addendum following Appendix 2 to Annex IX, in point 1.1.5 for “EU” substitute “GB”;

(m) in the notes following Appendix 2, in note (3) for “Annex IIA to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(n) in Appendix 3—

(i) for the image, substitute—

“

”

(ii) in the text following the image, omit “in Spain (e 9)”.

Regulation (EU) 2015/758

77.—(1) Regulation (EU) 2015/758 is amended as follows.

(2) In Article 1 (subject matter), for “EC” substitute “GB”.

(3) In Article 2 (scope)—

(a) in paragraph 1—

(i) in the opening words, for “points 1.1.1 and 1.2.1 of Part A of Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(ii) in the second subparagraph, in point (a)—

(aa) after “produced in” insert “medium and”;

(bb) for “Article 22 and 23 of Directive 2007/46/EC” substitute “Article 41 and 42 of Regulation (EU) 2018/858”;

(iii) in the second subparagraph, in point (b), for “Article 24 of Directive 2007/46/EC” substitute “Article 45 of Regulation (EU) 2018/858”;

(b) in paragraph 2—

(i) for “The Commission shall be empowered to adopt delegated acts in accordance with Article 8” substitute “The Secretary of State may make regulations”;

(ii) omit “which is carried out or mandated by the Commission”;

(iii) omit the second subparagraph;

(c) after paragraph 2, insert—

“3.   A type of vehicle which was subject to an approval under section 55(1A) or (1D) of the Road Traffic Act 1988(52) is not required to be approved in accordance with this Regulation.”.

(4) In Article 3 (definitions)—

(a) in the opening words, for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(b) in point (3), for “Member State” substitute “Secretary of State”;

(c) in point (9), for the words “Directives” to the end, substitute “the Communications Act 2003(53)”.

(5) In Article 5 (specific obligations of manufacturers)—

(a) in paragraph 2—

(i) in the first subparagraph, for “Union” substitute “the United Kingdom”;

(ii) omit “single European” both times it occurs;

(b) in paragraph 5, for “EC” substitute “GB”;

(c) in paragraph 7, for “Regulation (EC) No 715/2007” substitute “Chapter XIV of Regulation (EU) 2018/858”;

(d) in paragraph 8—

(i) in the first subparagraph—

(aa) for the words from the beginning to “Article 8” substitute “The Secretary of State may make regulations”;

(bb) for “EC type-approval” both times it occurs, substitute “GB type-approval”;

(ii) in point (f)—

(aa) omit “European” the first time it occurs;

(bb) for “adopted in conformity with the procedures laid down in Regulation (EU) No 1025/2012 of the European Parliament and of the Council(¹)” substitute “specified in regulations made by the Secretary of State”;

(cc) for “Union” substitute “United Kingdom”;

(iii) omit the final sentence;

(e) in paragraph 9, for “The Commission shall be empowered to adopt delegated acts in accordance with Article 8” substitute “The Secretary of State may make regulations”.

(6) In Article 6 (rules on privacy and data protection)—

(a) in paragraph 1—

(i) for “Directives 95/46/EC and 2002/58/EC” substitute “the Data Protection Act 2018(54), Regulation (EU) 2016/679(55) and the Privacy and Electronic Communications (EC Directive) Regulations 2003(56);

(ii) for “those Directives” substitute “those enactments”;

(b) in paragraph 9(i), for “Directive 95/46/EC” substitute “Regulation (EU) 2016/679 and the Data Protection Act 2018”;

(c) in paragraph 12—

(i) in the first subparagraph, for “The Commission shall be empowered to adopt delegated acts in accordance with Article 8” substitute “The Secretary of State may make regulations”;

(ii) omit the second subparagraph;

(d) in paragraph 13—

(i) in the first subparagraph, for “The Commission shall, by means of implementing acts”, substitute “The Secretary of State must, by regulations”;

(ii) omit the second and third subparagraphs.

(7) In Article 7 (obligations of the Member States)—

(a) in the heading, for “Member States” substitute “approval authority”;

(b) for “With effect from 31 March 2018, national authorities shall” substitute “The approval authority may”;

(c) for “EC” substitute “GB”.

(8) For Article 8 (exercise of the delegation), substitute—

“Article 8 Regulations

1.   Any power to make regulations conferred on the Secretary of State by this Regulation is exercisable by statutory instrument.

2.   Such regulations may—

(a) make incidental, supplemental, consequential or transitional provision, and

(b) make different provision for different cases or descriptions of case, different circumstances, different purposes or different areas.

3.   Before making any regulations to which paragraph 4 applies the Secretary of State must consult with such representative organisations as the Secretary of State thinks fit.

4.   This paragraph applies to regulations made under Articles 2(2), 5(8), and (9), and 6(12).

5.   A statutory instrument containing regulations made under this Regulation is subject to annulment in pursuance of a resolution of either House of Parliament.”.

(9) In Article 9 (implementing acts)—

(a) in the opening paragraph—

(i) for “The Commission shall adopt implementing acts” substitute “The Secretary of State may make regulations”;

(ii) for “EC”, each time it occurs, substitute “GB”;

(b) omit the second and third subparagraphs.

(10) Omit Articles 10 (committee procedure), 11 (penalties) and 12 (reporting and review).

(11) After Article 14 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States”.

Commission Implementing Regulation (EU) 2017/78

78.—(1) Commission Implementing Regulation (EU) 2017/78 is amended as follows.

(2) In Article 2 (EC type-approval: 112-based eCall in-vehicle systems)—

(a) in the heading, and each other time it occurs, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraph 1, for “Article 3(29) of Directive 2007/46/EC” substitute “Article 3(36) of Regulation (EU) 2018/858”;

(c) in paragraph 3—

(i) in the first subparagraph—

(aa) for “grant an” substitute “grant a”;

(bb) for “issue an” substitute “issue a”;

(cc) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the second subparagraph, for “A Member State” substitute “The approval authority”.

(3) In Article 3 (EC type-approval: 112-based eCall in-vehicle STUs etc)—

(a) in the heading, and each other time it occurs, for “EC type-approval” substitute “GB type-approval”;

(b) in paragraph 1, for “Article 3(29) of Directive 2007/46/EC” substitute “Article 3(36) of Regulation (EU) 2018/858”;

(c) in paragraph 3—

(i) for “grant an” substitute “grant a”;

(ii) after “issue” insert “a”;

(iii) for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”.

(iv) for “A Member State” substitute “The approval authority”.

(4) In Article 4 (EC type-approval mark)—

(a) in the heading, for “EC” substitute “GB”;

(b) for “an EC” both times it occurs, substitute “a GB”.

(5) After Article 6 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States”.

(6) In Annex I (Administrative documents for EC type-approval: installation of 112-based eCall in-vehicle systems)—

(a) in the heading, and each time it occurs, for “EC type-approval” substitute “GB type-approval”;

(b) in the explanatory notes to Part 1—

(i) in note (2), for “Part A of Annex II to Directive 2007/46/EC”, substitute “Article 4 of Regulation (EU) 2018/858”;

(ii) in note (4), for “Annex II of Directive 2007/46/EC” substitute “Annex I of Regulation (EU) 2018/858”;

(c) in Part 2—

(i) after “2015/758” insert “as it has effect in domestic law”;

(ii) for “by Regulation …/…” substitute “by S.I. …./….”;

(iii) in the explanatory notes to Part 2, in note (3), for “Part A of Annex II to Directive 2007/46/EC”, substitute “Article 4 of Regulation (EU) 2018/858”;

(iv) in the heading to the Addendum to Part 2, for “EC” substitute “GB”.

(d) in Part 3—

(i) in point 2.1—

(aa) for “Directives 95/46/EC and 2002/58/EC of the European Parliament and of the Council”, substitute “Regulation (EU) 2016/679, the Data Protection Act 2018(57) and the Privacy and Electronic Communications (EC Directive) Regulations 2003(58)”;

(bb) for “Article 7(d) of Directive 95/46/EC” substitute “Article 6(1)(d) of Regulation (EU) 2016/679(59)”;

(ii) in point 2.3.2—

(aa) for “respective public authorities of the country on which territory they are located” substitute “Secretary of State”;

(bb) omit “single European”;

(iii) in point 2.5.1—

(aa) for “Directive 95/46/EC” substitute “Regulation (EU) 2016/679 and the Data Protection Act 2018”;

(bb) for “this Directive” substitute “that Regulation and that Act”;

(iv) in point 3.2, for “Directives 95/46/EC and 2002/58/EC” substitute “Regulation (EU) 2016/679, the Data Protection Act 2018 and the Privacy and Electronic Communications (EC Directive) Regulations 2003”.

(7) In Annex II (administrative documents for EC type-approval: 112 based eCall in-vehicle STU etc)—

(a) in the heading, and each other time it occurs, for “EC type-approval” substitute “GB type-approval”;

(b) in Part 1, in point 0.7, for “EC” substitute “GB”;

(c) in the explanatory notes to Part 1, in note (2), for “Section A of Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(d) in Part 2—

(i) after “2015/758” insert “as it has effect in domestic law”;

(ii) in Section 1, in point 0.7, for “EC” substitute “GB”;

(e) in Part 3—

(i) in point 1, for “EC” substitute “GB”;

(ii) for point 1.1, substitute—

“1.1.   A rectangle surrounding the lower-case letter “g” followed by the number 11.”

(iii) in point 3—

(aa) in figure 1, for the image, substitute—

“

”

(bb) in the explanatory note following “figure 1”, for “EC” substitute “GB”, omit “by Bulgaria”, and for “0046” substitute “00026”;

(cc) in figure 2, for the image, substitute—

“

”

(dd) in the explanatory note following figure 2, for “EC” substitute “GB”, and omit “by Germany”.

Commission Delegated Regulation (EU) 2017/79

79.—(1) Commission Delegated Regulation (EU) 2017/79 is amended as follows.

(2) In the title of the Regulation, in Articles 1 and 8, and in Articles 5, 6 and 7 and their headings, for “EC type-approval”, substitute “GB type-approval”.

(3) In Article 3 (multi-stage approval of special purpose vehicles), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”.

(4) In Article 8—

(a) in the heading, for “Member States” substitute “approval authority”;

(b) in the Article, for “Member States” substitute “The approval authority”.

(5) After Article 10 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”

(6) In Annex I (technical requirements and procedures for testing the resistance of eCall in-vehicle systems to severe crashes), in point 2.2.4, for “Article 3(31) of Directive 2007/46/EC” substitute “Article 3(38) of Regulation (EU) 2018/858”.

(7) In Annex IX (classes of vehicles referred to in Article 2), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”.

Commission Regulation (EU) No 2017/1151: Articles

80.—(1) Commission Regulation (EU) No 2017/1151 is amended as follows.

(2) In Article 2 (definitions)—

(a) in point (2)—

(i) for “EC type-approval”, the first time it occurs, substitute “GB type-approval”;

(ii) for “an EC type-approval” substitute “a GB type-approval”;

(b) in point (32c), for “the Community”, substitute “Great Britain”.

(3) In Article 3 (requirements for type-approval)—

(a) in paragraph 1, for “an EC type-approval” substitute “a GB type-approval”;

(b) in paragraph 3—

(i) for “EC type-approval”, both times it occurs, substitute “GB type-approval”;

(ii) for “a third country” substitute “a country other than the United Kingdom”;

(iii) omit the third subparagraph;

(c) in paragraph 10, omit the final subparagraph.

(4) In Article 4 (requirements for type-approval re the OBD system), in paragraph 6, for “national authorities” substitute “the approval authority”.

(5) In Article 5 (application for EC type-approval: emissions and access to vehicle repair and maintenance information)—

(a) in the heading and in paragraph 1, for “EC type-approval” substitute “GB type-approval”;

(b) omit paragraph 5;

(c) in paragraph 6—

(i) in the first subparagraph, for “approval authorities” substitute “the approval authority”;

(ii) in the third subparagraph, for “authorities” substitute “authority”;

(d) in paragraph 11—

(i) in the first subparagraph, for “authorities” substitute “authority”;

(ii) for the sixth subparagraph, substitute—

“Each year, the approval authority must make available to the public a list of the AES which it has decided are not acceptable for the purposes of this paragraph.”;

(e) in paragraph 12, omit “which granted the emission type-approval under this Regulation (‘granting approval authority’)”.

(6) In Article 6 (administrative provisions for EC type-approval: emissions and access to vehicle repair and maintenance information)—

(a) in the heading, for “EC type-approval”, substitute “GB type-approval”;

(b) in paragraphs 1 and 3, for “an EC type-approval” substitute “a GB type-approval”;

(c) in paragraph 1—

(i) for “Annex VII to Directive 2007/46/EC”, both times it occurs, substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(ii) in the third subparagraph, for “An approval” substitute “The approval”;

(d) in paragraph 2, omit the second subparagraph;

(e) in paragraph 3, for “an EC type approval” substitute “a GB type-approval”.

(7) In Article 7 (amendments to type-approvals), for “Articles 13, 14 and 16 of Directive 2007/46/EC” substitute “Articles 33 and 34 of Regulation (EU) 2018/858”.

(8) In Article 8 (conformity of production), in paragraph 1, for “Article 12 of Directive 2007/46/EC”, substitute “Article 31 of Regulation (EU) 2018/858”.

(9) In Article 9 (in service conformity)—

(a) in paragraph 1, for “Annex X to Directive 2007/46/EC” substitute “Annex IV to Regulation (EU) 2018/858”;

(b) in paragraph 4, for “the Union” substitute “Great Britain”;

(c) in paragraph 5, omit “granting type”;

(d) in paragraph 6, omit “granting”;

(e) in paragraph 7—

(i) for the first and second subparagraphs, substitute—

“7.   If the approval authority has established that an in-service conformity family fails the in-service conformity check, it must inform the manufacturer that an in-service conformity family fails the in-service conformity checks and that the procedures described in points 6 and 7 of Annex II must be followed.”;

(ii) omit the third subparagraph;

(f) in paragraph 8—

(i) in point (a), for “Article 3(7) of Directive 2007/46/EC” substitute “Article 3(8) of Regulation (EU) 2018/858”;

(ii) in point (b)—

(aa) for “points 5.2 and 5.5 of Part A of Annex II to Directive 2007/46/EC”, substitute “points 5.2, 5.4 and 5.5 of Part A of Annex I to Regulation (EU) 2018/858”;

(bb) for “Annex II to Directive 2007/46/EC”, the second time it occurs, substitute “Annex I to Regulation (EU) 2018/858”.

(10) In Article 10 (pollution control devices), in paragraph 1—

(a) for “EC type-approved”, both times it occurs, substitute “GB type-approved”;

(b) for “Article 10(2) of Directive 2007/46/EC” substitute “Article 29(1) of Regulation (EU) 2018/858”.

(11) In Article 11 (application for EC type-approval: replacement pollution device as a separate technical unit), in the heading and in paragraph 1, for “EC type-approval” substitute “GB type-approval”.

(12) In Article 12 (administrative provisions for EC type-approval: replacement pollution device as a separate technical unit)—

(a) in the heading for “EC type-approval” substitute “GB type-approval”;

(b) in paragraphs 1 and 2, for “an EC type-approval” substitute “a GB type-approval”;

(c) in paragraph 1, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”.

(13) In Article 13 (access to vehicle OBD etc), omit paragraph 9.

(14) In Article 14 (compliance with obligations re access to vehicle OBD and vehicle repair and maintenance information), in paragraph 1, for “An approval” substitute “The approval”.

(15) In Article 15 (transitional provisions)—

(a) omit paragraph 1;

(b) in paragraph 2—

(i) for “national authorities”, both times it occurs, substitute “the approval authority”;

(ii) for “EC type approval or national type approval”, both times it occurs, substitute “GB type-approval”;

(c) in paragraph 3—

(i) in the first subparagraph—

(aa) for “national authorities” substitute “the Secretary of State”;

(bb) for “Article 26 of Directive 2007/46/EC” substitute “Article 48 of Regulation (EU) 2018/858”;

(ii) in the third subparagraph, for the words “national authorities” to the end, substitute “the registration, sale or entry into service of new vehicles that do not comply with Annex VI to this Regulation is prohibited.”;

(d) in paragraph 4, in the second subparagraph, for “EC type-approval” substitute “GB type-approval”;

(e) in paragraph 5, in point (c) for “authorities” substitute “authority”;

(f) omit paragraph 6;

(g) in paragraph 9—

(i) in the first subparagraph—

(aa) for “national authorities” substitute “the approval authority”;

(bb) for “EC type approval or national type approval” substitute “GB type-approval”;

(ii) in the second subparagraph, for the words “national authorities” to the end, substitute “the registration, sale or entry into service of new vehicles that do not comply with that Article is prohibited.”;

(h) in paragraph 10, in the first subparagraph, for the words from “national authorities” to the end, substitute “the registration, sale or entry into service of new vehicles that do not comply with the requirements set out in Annex VIII of Commission Implementing Regulation (EU) 2020/683 is prohibited.”.

(16) After Article 20 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.

Commission Regulation (EU) 2017/1151: Annexes

81.—(1) The Annexes to Commission Regulation (EU) 2017/1151 are amended as follows.

(2) In Annex I (administrative provisions for EC type-approval)—

(a) in the heading, and each other time it occurs, for “EC type-approval” substitute “GB type-approval”;

(b) in point 4.1.1, for “Annex X of Directive 2007/46/EC”, substitute “Annex IV of Regulation (EU) 2018/858”;

(c) in the second subparagraph of point 4.1.2, omit the words “and shall make it” to the end;

(d) in point 4.1.7, omit the second sentence;

(e) in point 4.1.8, for “Article 30 of Directive 2007/46/EC” substitute “Article 54 of Regulation (EU) 2018/858”;

(f) in point 4.2.6.1, for “Article 12 of Regulation (EC) No 443/2009 for M1 vehicles or Article 12 of Regulation (EU) No 510/2011 for N1 vehicles” substitute “Article 11 of Regulation (EU) No 2019/631(60)”;

(g) in Appendix 3—

(i) in the heading and in point 3.2.18.1, for “EC type-approval” substitute “GB type-approval”;

(ii) in point 3.5.8, for “Article 12 of Regulation (EC) No 443/2009 for M1 vehicles or Article 12 of Regulation (EU) No 510/2011 for N1 vehicles” substitute “Article 11 of Regulation (EU) 2018/858”;

(iii) in point 9.1, for “Annex II of Directive 2007/46” substitute “Annex I of Regulation (EU) 2018/858”;

(h) in the explanatory notes following point 16.3 of Appendix 3—

(i) in note (o), for “Council Directive 80/1268/EC (OJ L 375, 31.12.1980, p. 36)” substitute “Regulation (EC) 715/2007(61)”;

(ii) in note (w2) and (w3), omit “the Commission Decision approving”;

(i) in Appendix 4—

(i) in the heading, and each other time it occurs, for “EC type-approval” substitute “GB type-approval”;

(ii) in the opening section, after “2017/1151” insert “as they have effect in domestic law”;

(iii) in the note of attachments after point 8 in Section II, after “information package” omit the reference to note (⁶);

(j) in the Addendum to EC type-approval certificate after Appendix 4, in the heading, for “EC” substitute “GB”;

(k) in the explanatory notes following the Addendum—

(i) in note (^5a), for “point 18 of Directive 2007/46/EC” substitute “point 24 of Regulation (EU) 2018/858”;

(ii) omit note (⁶);

(iii) for the words in note (²⁶) substitute “The general code of the eco-innovation(s) is to consist of the two-digit codes for each individual eco-innovation, separated by spaces (e.g. 10 15 16)”;

(l) in Appendix 6—

(i) in the heading and in point 1, each time it occurs, for “EC” substitute “GB”;

(ii) in point 2.1—

(aa) omit “issued by Luxembourg, identified by the code e3”;

(bb) in the formula following the point, for “e13” substitute “g11”;

(iii) in point 2.2—

(aa) omit “issued by Romania, identified by the code e19”;

(bb) in the formula following the point, for “e19” substitute “g11”;

(m) in Appendix 7, in the certificate of compliance, after “2017/1151” insert “as it applies in domestic law”.

(3) In Annex II—

(a) in Part A (in-service conformity)--

(i) in point 2.1, for “Article 12(1) and (2) of Directive 2007/46/EC and in points 1 and 2 of Annex X to that Directive” substitute “Article 31(1), (3) and (4) of Regulation (EU) 2018/858 and in points 2 and 3 of Annex IV to that Regulation”;

(ii) in point 2.3, for “‘Member States’”, substitute “‘the United Kingdom’”;

(iii) in point 2.4—

(aa) after “Directive 2007/46/EC” insert “or with Regulation (EU) 2018/858”;

(bb) for “Union” substitute “United Kingdom”;

(iv) in point 2.5, for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(v) in point 2.6, for “Directive 2009/30/EC of the European Parliament and of the Council(1)” substitute “the Motor Fuel (Composition and Content) Regulations 1999(62)”;

(b) in Part B (new in-service conformity methodology)—

(i) in point 5—

(aa) in the first subparagraph, omit the words from “using the Electronic” to the end;

(bb) in the second subparagraph, omit the second sentence;

(cc) in the third subparagraph, omit the words from “using the Electronic” to the end;

(ii) in point 5.1, in the first subparagraph, for “Article 41 of Directive 2007/46/EC” substitute “Article 68 of Regulation (EU) 2018/858”;

(iii) in point 5.7.1—

(aa) in the first subparagraph, after “Union” both times it occurs, insert “or the United Kingdom”;

(bb) in the sixth subparagraph, for “Directive 98/70/EC of the European Parliament and of the Council” substitute “the Motor Fuel (Composition and Content) Regulations 1999”;

(iv) in point 5.8—

(aa) in the first subparagraph, for “the Union” substitute “Great Britain”;

(bb) in Table B.1, in the heading to the first column, for “EU” substitute “GB”;

(v) in point 5.9—

(aa) in the heading, omit “Use of the Electronic Platform for in-service conformity and”;

(bb) omit the first and third subparagraphs;

(vi) in point 5.10.1, in the fourth subparagraph, for “Annex IX of Directive 2007/46/EC” substitute “Annex VIII to Commission Implementing Regulation (EU) 2020/683”;

(vii) in point 7.6, for “Article 30 of Directive 2007/46/EC” substitute “Article 54 of Regulation (EU) 2018/858”;

(viii) omit point 7.7;

(ix) in point 7.9, omit “in all Member States”;

(x) in point 7.10—

(aa) for “per Member State”, both times it occurs, substitute “in Great Britain”;

(bb) for the words from “the granting type approval” to “the Commission”, substitute “the approval authority”;

(xi) in point 7.11—

(aa) for “Member States” substitute “The Secretary of State”;

(bb) for “in their territory” substitute “in Great Britain”;

(c) in Appendix 1, in the table—

(i) in the fourth row (country of registration), omit “(in EU only)”;

(ii) in the eleventh row (country of registration), for “in the EU” substitute “in the UK or the EU”;

(iii) in the thirty-ninth row (has the car been used with wrong fuel type), for “non-commercially available EU quality fuel” substitute “fuel that is neither commercially available nor UK quality fuel”;

(iv) in the forty-eighth row (driving in non-EU Member States), for “in a non EU Member State” substitute “outside the United Kingdom in a country which is not an EU Member State”;

(v) in the forty-ninth row (country in which vehicle refuelled) for “outside a country applying the EU Fuel Standards” substitute “in a country outside the UK which does not apply the EU Fuel Standards”.

(4) In Annex IIIA (verifying real driving emissions)—

(a) omit point 2.3;

(b) in point 2.4, for “Article 7(1) of Regulation (EC) No 715/2007” substitute “Article 63 of Regulation (EU) 2018/858”;

(c) in point 3.1.3.2, for “the Commission and the Type Approval Authorities” substitute “the approval authority”;

(d) in point 3.1.3.2.1, for “Annex IX to Directive 2007/46/EC”, in both places it occurs, substitute “Annex VIII to Commission Implementing Regulation (EU) 2020/683”;

(e) in point 6.4, for “Directive 92/6/EEC” substitute “Regulation 36B of the Road Vehicles (Construction and Use) Regulations 1986(63)”;

(f) in point 6.5, for “Directive 92/6/EEC” substitute “Regulation 36B of the Road Vehicles (Construction and Use) Regulations 1986”;

(g) in point 6.9—

(i) in the second subparagraph, for “Directive 92/6/EEC” substitute “Regulation 36A of the Road Vehicles (Construction and Use) Regulations 1986”;

(ii) in the third subparagraph, for “Directive 92/6/EEC” substitute “Regulation 36B of the Road Vehicles (Construction and Use) Regulations 1986”;

(h) in point 7.4, omit “for the Union”;

(i) in Appendix 5 to Annex IIIA—

(i) in point 4.4.2 and 4.4.3, in the second subparagraph in each case, for “Directive 92/6/EEC” substitute “Regulation 36B of the Road Vehicles (Construction and Use) Regulations 1986”;

(ii) after point 4.4.3, in the titles to Figure 5 and Figure 6, for “Directive 92/6/EEC” substitute “Regulation 36B of the Road Vehicles (Construction and Use) Regulations 1986”;

(j) in Appendix 6 to Annex IIIA—

(i) in point 2.1 in the final subparagraph—

(aa) for “Commission” substitute “Secretary of State”;

(bb) for “mathetical” substitute “mathematical”;

(ii) in point 2.3, in the first subparagraph, in the final sentence, for “Commission” substitute “Secretary of State”;

(k) in Appendix 7—

(i) in point 1, for “Annex IX to Directive 2007/46/EC” substitute “Annex VIII to Commission Implementing Regulation (EU) 2020/683”;

(ii) in point 5.2—

(aa) for “MS-OEM-X-Y” substitute “GB-OEM-X-Y”;

(bb) omit the words from “MS is the distinguishing” to “type-approval(¹)”;

(iii) in point 5.3, for “EC” substitute “GB”.

(5) In Annex XI (on-board diagnostics for motor vehicles)—

(a) for point 4.4, substitute—

“4.4.   Paragraph 5.2.1(c) of Annex 11 to UNECE Regulation 83(64) shall be read as if “The Type Approval Authority shall transmit this information to the Type Approval Authorities of the Contracting Parties and” were omitted.”;

(b) in point 4.6, for “EC” substitute “GB”;

(c) in Appendix 1, in point 3.1.2—

(i) in the second subparagraph—

(aa) omit “and, upon request, to the Commission”;

(bb) for “in the Union” substitute “in Great Britain”;

(ii) in the third subparagraph—

(aa) in the penultimate sentence, omit “by Member States”;

(bb) omit the final sentence.

(6) In Annex XII (type-approval of vehicles fitted with eco-innovations etc)—

(a) in point 1.1, for “an EC type-approval” substitute “a GB type-approval”;

(b) in point 1.2, after “Commission Decision” inset “or the decision of the Secretary of State”;

(c) in point 1.3, for “Directive 2007/46/EC” substitute “Regulation (EU) 2018/858”;

(d) in point 2.1, for “Article 3(7) of Directive 2007/46/EC”, substitute “Article 3(8) of Regulation (EU) 2018/858”;

(e) in point 2.6, for “Annex IX to Directive 2007/46/EC” substitute “Annex VIII to Commission Implementing Regulation (EU) 2020/683”.

(7) In Annex XIII (EC type-approval of replacement pollution control devices as separate technical units)—

(a) in the heading, and the heading at point 3, for “EC” substitute “GB”;

(b) in point 3.1, for “an EC” substitute “a GB”;

(c) in point 3.2—

(i) for “EC type-approval”, each time it occurs, substitute “GB type-approval”;

(ii) in the first subparagraph, for the words from “letter” to the end, substitute “letter ‘g’ followed by the number 11”;

(iii) in the second subparagraph, for “Annex VII to Directive 2007/46/EC” substitute “Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(d) in points 3.3 and 3.4, for “EC” substitute “GB”;

(e) in point 4.1.5, for “EC type-approval” substitute “GB type-approval”;

(f) in point 6.1, for “Article 12 of Directive 2007/46/EC”, substitute “Article 31 of Regulation (EU) 2018/858”;

(g) in point 6.2.1, for “point 2.2 of Annex X to Directive 2007/46/EC”, substitute “point 2.1 of Annex IV to Regulation (EU) 2018/858”;

(h) in point 6.2.2, for “Article 12(2) of Directive 2007/46/EC” substitute “Article 31(3) of Regulation (EU) 2018/858”;

(i) in Appendix 1, in the heading, and in point 0.7, for “EC” substitute “GB”;

(j) in Appendix 2—

(i) for “EC type-approval”, in the headings and each other time it occurs, substitute “GB type-approval”;

(ii) in point 0.7, for “EC” substitute “GB”;

(k) in Appendix 3—

(i) in the heading, for “EC” substitute “GB”;

(ii) for the image, substitute—

“

”

(iii) in the text following the image, omit “in France (e 2),”.

(8) In Annex XIV (Access to vehicle OBD and vehicle repair and maintenance information)—

(a) in point 2.2—

(i) in the second subparagraph, for the words from the beginning to “Article 13 will” substitute “The Secretary of State may by regulations”;

(ii) after the second subparagraph, insert—

“Article 15 of Regulation (EC) No 715/2007 applies to regulations made by the Secretary of State under this paragraph as it applies to regulations made under Regulation (EC) No 715/2007.”;

(b) in Appendix 1, after “the provisions of” insert “the following Regulations, as they apply in domestic law”.

(9) In Annex XXI (Type 1 emissions test procedures), in point 3.2.18, for “Annex IV and Annex XI of Directive 2007/46/EC”, substitute “Annex II of Regulation (EU) 2018/858”.

Commission Regulation (EU) 2017/2400: Articles

82.—(1) Commission Regulation (EU) 2017/2400 is amended as follows.

(2) In Article 1 (subject matter), for “in the Union” substitute “in Great Britain”.

(3) In Article 2 (scope)—

(a) in paragraph 1, for “Annex II to Directive 2007/46/EC” substitute “Article 4 of Regulation (EU) 2018/858”;

(b) in paragraph 3, for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(4) In Article 3 (definitions)—

(a) omit point (5);

(b) in point (16), for “Annex II to Directive 2007/46/EC” substitute “Annex I to Regulation (EU) 2018/858”;

(c) in point (20), for “as defined in Article 3(15) of Directive 2007/46/EC” substitute—

“a hybrid vehicle that, for the purpose of mechanical propulsion, draws energy from both of the following on-vehicle sources of stored energy or power—

(a) a consumable fuel;

(b) an electrical energy or power storage device, such as, for example, a battery, capacitator, flywheel or generator;”.

(5) In Article 5 (electronic tools)—

(a) in paragraph 1—

(i) in the opening words, for “The Commission shall provide free of charge the following tools in the form of downloadable and executable software”, substitute “The approval authority must use the following electronic tools, as provided by the Commission under Article 5 of this Regulation as it has effect in EU law”;

(ii) in the closing words, omit the words from “The Commission” to the end;

(b) omit paragraph 2.

(6) In Article 6(4) (application for a licence to operate the simulation tool etc)—

(a) for “an EC type-approval”, both times it occurs, substitute “a GB type-approval”;

(b) omit “and access to vehicle repair and maintenance information” both times it occurs;

(c) in the final sentence, for “EC type-approval” substitute “GB type-approval”.

(7) In Article 9 (obligation to determine and declare CO₂ emissions and fuel consumption)—

(a) in paragraph 1, for “in the Union” both times it occurs, substitute “in Great Britain”;

(b) in paragraph 5, for “Article 24 of Directive 2007/46/EC” substitute “Article 45 of Regulation (EU) 2018/858”.

(8) In Article 10 (modifications, updates and malfunctions of electronic tools)—

(a) in paragraph 1, after “made available” insert “by the Commission in accordance with paragraph 1 of Article 5 of this Regulation as it applies in EU law”;

(b) after paragraph 1, insert—

“1a.   The approval authority must notify approval holders as soon as practicable on each occasion that the simulation tool is updated by the Commission.”;

(c) in paragraph 2, for the words from “the Commission” to the end” substitute “the approval authority without delay”.

(9) In Article 11 (accessibility of the simulation tool inputs and output information)—

(a) in paragraph 1, omit “and the Commission”;

(b) omit paragraphs 2 and 3.

(10) In Article 12 (components, separate technical units and systems relevant to determine CO₂ emissions and fuel consumption), after paragraph 7, insert—

“8.   A manufacturer may choose to comply with paragraphs 2, 3 and 4 by submitting values determined in accordance with Articles 13 and 14, and certified in accordance with Article 17, of Regulation (EU) 2017/2400 as it applies in EU law, provided that the components, separate technical units or systems concerned were certified before 31st December 2026.”.

(11) In Article 16(3) (application for certification of CO₂ emissions and fuel consumption related properties), in the second subparagraph—

(a) for “an approval” substitute “the approval”;

(b) for “point 1 of Annex X of Directive 2007/46/EC” substitute “point 2 of Annex IV of Regulation (EU) 2018/858”.

(12) In Article 19(1) (subsequent changes relevant to the certification of CO₂ emissions etc), after “pursuant to” insert “Article 12(8) or”.

(13) In Article 20 (responsibilities re conformity of simulation tool operation)—

(a) in paragraph 1, in the second subparagraph, omit the words from “and shall make them available” to the end;

(b) in paragraph 2—

(i) in the second subparagraph, omit the second sentence;

(ii) omit the fourth subparagraph.

(14) In Article 21 (remedial measures for the conformity of simulation tool operation), in paragraph 3, omit “and all the other Member States”.

(15) In Article 22 (responsibilities re conformity of CO₂ emissions etc)—

(a) in paragraph 1—

(i) for “Annex X to Directive 2007/46/EC” substitute “Annex IV to Regulation (EU) 2018/858”;

(ii) after “Article 17”, insert “or with Article 12(8), where such components, separate technical units and systems are fitted to the vehicle,”;

(b) in paragraph 2, for the second sentence, substitute “In the case of components, separate technical units or systems approved under Article 12(8), the manufacturer must provide the approval authority with the test reports that were sent to the certifying approval authority in the relevant member State.”;

(c) omit paragraph 3;

(d) in paragraph 4, for “Any approval authority” substitute “The approval authority”.

(16) In Article 23 (remedial measures for the conformity of CO₂ emissions etc)—

(a) in paragraph 1, after “Article 17” insert “or Article 12(8)”;

(b) in paragraph 3, in the first sub-paragraph, omit “and all the other Member States”.

(17) In Article 24(1) (transitional provisions), in the opening words, for “Member States shall prohibit the registration, sale or entry into service of” substitute “the registration, sale or entry into service of the following vehicles is prohibited”.

(18) After Article 27 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States”.

Commission Regulation (EU) 2017/2400: Annexes

83.—(1) The Annexes to Commission Regulation (EU) 2017/2400 are amended as follows.

(2) In Annex II (requirements and procedures: operation of simulation tool)—

(a) in point 1.1.3, omit the words from “consulting” to “as well as”;

(b) in Appendix 2—

(i) after “Regulation (EU) 2017/2400” insert “both as they have effect in domestic law”;

(ii) in Section II, omit point 2.

(3) In Annex III (input information: characteristics of the vehicle), in the second subparagraph of point 4.1, for “Annex IV and Annex XI to Directive 2007/46/EC” substitute “Annex II to Regulation (EU) 2018/858”.

(4) In Annex V (verifying engine data)—

(a) in appendix 4, in point 7.4, for “EC” substitute “GB”;

(b) in appendix 6—

(i) for point 1.3, substitute—

“1.3.   The certification mark as a rectangle surrounding the lower-case letter ‘g’ followed by the number 11.”;

(ii) in point 1.4, for “Annex VII to Directive 2007/46/EC” substitute “point 2.4 of Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(iii) in point 1.4.1—

(aa) for the image, substitute—

“

”

(bb) in the words following the image, omit “in Poland (e20),”;

(iv) in point 1.5.1—

(aa) for the image, substitute—

“

”

(bb) in the words following the image, omit “in Poland (e20),”;

(v) in point 2.1, in the example certification number, at the beginning, for “eX” substitute “g11”;

(vi) in the table following point 2.1, in the column headed “Section 3” for “Latest amending Regulation (ZZZZ/ZZZZ)” substitute “Latest amending Statutory Instrument (S.I. ZZZZ/ZZZZ)”.

(5) In Annex VI (verifying transmission, torque convertor and other data)—

(a) in point 3.4.7, for “an approval” substitute “the approval”;

(b) in point 8, for “an approval” substitute “the approval”;

(c) in Appendix 1, in the second paragraph, omit “Regulation (EC) No XXXXX and”;

(d) in Appendices 2, 3, 4 and 5, in point 0.8 in each case, for “EC approval” substitute “GB approval”;

(e) in Appendix 7—

(i) for point 1.3, substitute—

“1.3.   The certification mark as a rectangle surrounding the lower-case letter ‘g’ followed by the number 11.”;

(ii) in point 1.4, for “Annex VII to Directive 2007/46/EC” substitute “point 2.4 of Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(iii) in point 1.5—

(aa) for the image, substitute—

“

”

(bb) in the words following the image, omit “in Poland (e20),”;

(iv) in point 2.1, in the example certification number, at the beginning, for “eX” substitute “g11”;

(v) in the table following point 2.1, in the column headed “Section 3”, for “Latest amending Regulation (ZZZZ/ZZZZ)” substitute “Latest amending Statutory Instrument (S.I. ZZZZ/ZZZZ)”.

(6) In Annex VII (verifying axle data)—

(i) in point 5.1, for “Article 12 of Directive 2007/46/EC” substitute “Article 31 of Regulation (EU) 2018/858”;

(b) in Appendix 1—

(i) in the opening section—

(aa) after “2017/2400” the first time it appears, insert “as it has effect in domestic law, as last amended by S.I. …./….”;

(bb) omit the following words “Commission Regulation (EU) 2017/2400 as last amended by …”;

(ii) in Section I, in point 0.5, for “EC” substitute “GB”;

(c) in Appendix 5—

(i) for point 1.3, substitute—

“1.3.   The certification mark as a rectangle surrounding the lower-case letter ‘g’ followed by the number 11.”;

(ii) in point 1.4, for “Annex VII to Directive 2007/46/EC” substitute “point 2.4 of Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(iii) in point 1.4.1—

(aa) for the image, substitute—

“

”

(bb) in the words following the image, omit “in Poland (e20),”;

(iv) in point 2.1, in the example certification number, at the beginning, for “eX” substitute “g11”;

(v) in the table following point 2.1, in the column headed “Section 3”, for “Latest amending Regulation (ZZZZ/ZZZZ)” substitute “Latest amending Statutory Instrument (S.I. ZZZZ/ZZZZ)”.

(7) In Annex VIII (verifying air drag data)—

(a) in point 2(12), for the definition ‘EMS’ substitute “‘EMS’ means the European Modular System, denoting a vehicle combination consisting of a vehicle of category N, towing both a semi-trailer and either a trailer or a dolly, whether or not coupled together in that order”;

(b) in Appendix 1—

(i) in the opening section—

(aa) after “2017/2400” the first time it appears, insert “as last amended by S.I. …./….”;

(bb) omit the following words “Commission Regulation (EU) 2017/2400 as last amended by …”;

(ii) in Section I, in point 0.6, for “EC” substitute “GB”;

(c) in Appendix 4—

(i) in tables 11 and 13, in the second row (width), omit “(96/53/EC)”;

(ii) in table 15—

(aa) omit “(96/53/EC)” each time it occurs;

(bb) in the eighth row (front overhang), and the tenth row (corner front/side panel), omit “, 96/53/EC”;

(d) in Appendix 8—

(i) for point 1.3, substitute—

“1.3.   The certification mark as a rectangle surrounding the lower-case letter ‘g’ followed by the number 11.”;

(ii) in point 1.4, for “Annex VII to Directive 2007/46/EC” substitute “point 2.4 of Annex IV to Commission Implementing Regulation (EU) 2020/683”;

(iii) in point 1.4.1—

(aa) for the image, substitute—

“

”

(bb) in the words following the image, omit “in Poland (e20),”;

(iv) in point 2.1, in the example certification number, at the beginning, for “eX” substitute “g11”;

(v) in the table following point 2.1, in the column headed “Section 3”, for “Latest amending Regulation (ZZZZ/ZZZZ)” substitute “Latest amending Statutory Instrument (S.I. ZZZZ/ZZZZ)”.

(8) In Annex X (certification procedure for pneumatic tyres)—

(a) in point 3.3—

(i) in the opening words, for “Article 41 of Directive 2007/46/EC” substitute “Article 68 of Regulation (EU) 2018/858”;

(ii) in point (i), for “an approval” substitute “the approval”;

(iii) in point (ii), for “Directive 2007/46/EC, Article 41” substitute “Article 68(1)(a) of Regulation (EU) 2018/858,”;

(b) in point 3.4.4, for “Article 19(2) of Directive 2007/46/EC” substitute “Article 38 of Regulation (EU) 2018/858”;

(c) in Appendix 1, in the opening words, for “as amended by Commission Regulation (EU) 2019/318” substitute “as last amended by S.I. …. / ….”;

(d) in Appendix 4—

(i) in point 1.1, in the example certification number, at the beginning, for “eX” substitute “g11”;

(ii) in the table following point 1.1, in the column headed “Section 3”, for “Latest amending Regulation (ZZZZ/ZZZZ)” substitute “Latest amending Statutory Instrument (S.I. ZZZZ/ZZZZ)”.

(9) In Annex Xa (conformity of simulation tool operation and of CO₂ emissions and fuel consumption related properties etc)—

(a) in paragraph 3(f), after “manufacturer” insert “in Great Britain”;

(b) in the table following paragraph 3(f), for the heading to the second column, substitute

(c) “Verification testing procedure relevant vehicles sold in GB/year”.

Regulation (EU) 2019/2144

84.  Regulation (EU) 2019/2144 of the European Parliament and of the Council of 27 November 2019 on type-approval requirements for motor vehicles and their trailers, and systems, components and separate technical units intended for such vehicles, as regards their general safety and the protection of vehicle occupants and vulnerable road users, is revoked.

Commission Implementing Regulation (EU) 2020/683: Articles

85.—(1) Commission Implementing Regulation (EU) 2020/683 is amended as follows.

(2) In Article 1 (templates for the information document)—

(a) in paragraph 1, in the opening words, for “EU type-approval” substitute “GB type-approval”;

(b) in paragraph 2, for “EU whole-vehicle” substitute “GB whole-vehicle”.

(3) In Article 2 (templates for EU type-approval certificates)—

(a) in the heading—

(i) for “EU” the first two times it occurs, substitute “GB”;

(ii) for “small” substitute “medium”;

(iii) omit “, and EU individual vehicle approval certificates”;

(b) for “an EU” each time it occurs, substitute “a GB”;

(c) omit paragraph 4.

(4) In Article 3—

(a) in the heading, omit “national” both times it occurs;

(b) for “small” substitute “medium”.

(5) In Article 4, omit “, 44(4)”.

(6) In Article 5 (model for the EU type-approval mark for components and separate technical units), including in the heading, for “EU type-approval” both times it appears, substitute “GB type-approval”.

Commission Implementing Regulation (EU) 2020/683: Annexes

86.—(1) The Annexes to Commission Implementing Regulation (EU) 2020/683 are amended as follows.

(2) In Annex I—

(a) in the explanatory notes—

(i) for the words in note (⁸), substitute “According to section 1 of the Automated and Electric Vehicles Act 2018 (c.18).”;

(ii) for the words in note (²⁹), substitute “Commission Regulation (EU) No 1230/2012 of 12 December 2012 implementing Regulation (EC) No 661/2009 of the European Parliament and of the Council with regard to type-approval requirements for masses and dimensions of motor vehicles and their trailers and amending Directive 2007/46/EC of the European Parliament and of the Council (EUR 2012/1230).”;

(iii) in note (⁵⁶), for the words “Regulation No 101” to the end, substitute “Regulation (EC) 715/2007 of the European Parliament and of the Council of 20 June 2007 on type approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and on access to vehicle repair and maintenance information (EUR 2007/715)”;

(iv) for the words in note (⁶⁰), substitute “Regulation (EU) 2019/631 of the European Parliament and of the Council of 17 April 2019 setting CO₂ emission performance standards for new passenger cars and for new light commercial vehicles, and repealing Regulations (EC) No 443/2009 and (EU) No 510/2011 (EUR 2019/631).”;

(v) omit note (⁶¹);

(vi) in notes (⁶⁵) and (⁶⁶), for “Commission Decision” substitute “document”;

(vii) in note (¹⁰⁶), for “EU” substitute “GB”;

(viii) in notes (¹⁴⁴)—

(aa) for “Commission Decision” substitute “Document”;

(bb) in the second sentence, for “Regulation (EC) No 443/2009 of the European Parliament and of the Council (OJ L 140. 5.6.2009, p. 1)” substitute “Regulation (EU) 2019/631 (EUR 2019/631)”;

(ix) in note (¹⁴⁵), for “Commission Decision” substitute “document”;

(x) in note (¹⁴⁷), for “Commission Implementing Regulation XX/XXX of …. on” substitute “this Regulation,”;

(xi) in note (¹⁵¹), for the words after “consist of” to the end, substitute “the two-digit codes for each individual eco-innovation, each separated by a blank space”;

(xii) in note (¹⁵⁵), for the existing text substitute “The speedometer must be capable of showing both imperial and metric measures, at the choice of the driver, if they are not displayed simultaneously.”;

(xiii) in note (¹⁵⁶)—

(aa) for “Member States” substitute “Secretary of State”;

(bb) for the words from “in a Member State” to the end, substitute “intended for use in right hand traffic”;

(b) in the Template for an information document for the EU type-approval of vehicle, systems, components or separate technical units—

(i) in the heading, for “EU” substitute “GB”;

(ii) in the opening paragraph, and on each other time it occurs, for “EU type-approval” substitute “GB type-approval”;

(iii) for point 1.11, substitute—

“1.11.   Vehicle is designed to be capable, in at least some circumstances or situations, of safely driving itself: yes/no (⁴) (⁸).”;

(iv) in point 2.4.2.1.3, for “Article 9a of Council Directive 96/53/EC (²⁹)” substitute “Appendix 5 of Annex I to Commission Regulation (EU) 1230/2012 (²⁹)”;

(v) in point 2.6.4, for “Additional mass” substitute “Increase in mass”;

(vi) in point 3.5.6, for the words from “Article 12” to “N₁ vehicles”, substitute “Article 11 of Regulation (EU) No 2019/631 of the European Parliament and of the Council (⁶⁰)”;

(vii) in the table at point 3.5.6.3, in the heading of the first column, for “Decision” substitute “Document”;

(viii) in point 3.5.8, for the words from “Article 12” to “N1 vehicles”, substitute “Article 11 of Regulation (EU) No 2019/631 of the European Parliament and of the Council (⁶⁰)”.

(3) In Annex II (template for an information document for whole vehicle step-by-step approval)—

(a) in the heading, for “EU” substitute “GB”;

(b) in the opening paragraph, for “EU type-approval” substitute “GB type-approval”;

(c) in Part III, in the fourth column of the table, omit “Member State or”.

(4) In Annex III (templates for approval certificates)—

(a) in point 1.2, omit the words from “(for approval” to “Greek characters)”;

(b) in point 1.3, in the second subparagraph—

(i) omit “national”, the first time it occurs;

(ii) for “National” substitute “GB” ;

(c) in points 1.4 and 1.5, for “EU” substitute “GB”;

(d) omit point 1.6;

(e) in point 1.7, omit “national”;

(f) in the template for Model A—

(i) in the heading and in the opening section—

(aa) for “EU vehicle” substitute “GB vehicle”;

(bb) for “EU whole” each time it occurs, substitute “GB whole”;

(cc) for “EU type-approval” each time it occurs, substitute “GB type-approval”;

(ii) after “Communication concerning granting/extension/refusal/withdrawal”—

(aa) in the second indent, for “Commission” substitute “approval authority”, and omit “in accordance with Article 39(3) thereof”;

(bb) omit the third indent;

(cc) in the fourth indent, for “small” substitute “medium”;

(dd) in the fifth indent, for “national” substitute “GB”;

(iii) in Section II—

(aa) for “EU type-approval” substitute “GB type-approval”;

(bb) in the heading before Part 2, for “EU VEHICLE” substitute “GB VEHICLE”;

(iv) in Part 2, for “EU type-approval”, each time it occurs, substitute “GB type-approval”;

(g) in the template for Model B—

(i) in the heading, and in the opening section, for “EU type-approval” substitute “GB type-approval”;

(ii) in the opening section, for “EU system”, each time it occurs, substitute “GB system”;

(iii) after “Communication concerning granting/extension/refusal/withdrawal”—

(aa) in the second indent, for “Commission” substitute “approval authority”, and omit “in accordance with Article 39(3) thereof”;

(bb) omit the third indent;

(iv) in the Addendum following Section II, for “EU type-approval” in the heading and in point 2, substitute “GB type-approval”;

(h) in the template for Model C—

(i) in the heading, for “EU” substitute “GB”;

(ii) in the opening section, for “EU component” each time it occurs, substitute “GB component”;

(iii) after “Communication concerning granting/extension/refusal/withdrawal”—

(aa) in the second indent, for “Commission” substitute “approval authority” and omit “in accordance with Article 39(3) thereof”;

(bb) omit the third indent;

(iv) in the following subparagraph, for “EU” substitute “GB”;

(v) in Section I, in point 0.7, for “EU” substitute “GB”;

(vi) in the Addendum following Section II, in the heading, for “EU” substitute “GB”;

(i) omit the template for Model D;

(j) in the template for Model E—

(i) in the heading, omit “national” both times it occurs;

(ii) in the row following the heading, for “e(4)” substitute “g11”;

(iii) in the text before Section I, omit “national” both times it occurs;

(iv) in Section I, in the text after point 0.10—

(aa) in the second paragraph, for “issuing Member State” substitute “approval authority”;

(bb) in the third paragraph, for “(name of the Member State)” substitute “Great Britain”;

(k) in Appendix 1—

(i) in the heading, omit “EU individual vehicle approval certificate and of the national”;

(ii) in the section relating to Category N2, in point 5.2, for “Article 9a of Directive 96/53/EC” substitute “Appendix 5 of Annex I to Commission Regulation (EU) 1230/2012”;

(iii) in the section relating to Category N3, in point 5.2, for “Article 9a of Directive 96/53/EC” substitute “Appendix 5 of Annex I to Commission Regulation (EU) 1230/2012”.

(5) In Annex IV (approval certificate numbering system)—

(a) for point 2.1, substitute—

“The lower-case letter ‘g’ is followed by the number 11.”;

(b) in point 2.2—

(i) for “an EU type-approval” both times it occurs, substitute “a GB type-approval”;

(ii) for “or Commission Implementing Regulation” substitute “, Commission Implementing Regulation or Statutory Instrument”;

(iii) after point (c), insert—

“(d) the number of the Statutory Instrument laying down the applicable requirements.”;

(c) in point 2.3—

(i) in the opening words—

(aa) for “or Commission Implementing Regulation” substitute “, Commission Implementing Regulation or Statutory Instrument”;

(bb) after “Regulation/Directive” both times it occurs, insert “/Statutory Instrument”;

(ii) in the second paragraph—

(aa) in the opening words and in point (a), for “an EU type-approval”, substitute “a GB type-approval”;

(bb) in point (a), for “small” substitute “medium”;

(cc) in point (b), omit “national”;

(dd) omit point (c);

(ee) in point (d), for “a national” substitute “an”;

(iii) in the third paragraph, for “Directive or Regulation” both times it occurs, substitute “Directive, Regulation or Statutory Instrument”;

(d) in point 2.4—

(i) for “an EU” both times it occurs, substitute “a GB”;

(ii) for “EU type-approval” substitute “GB type-approval”;

(iii) for “small series”, the first time it occurs, substitute “medium series”;

(iv) for “national” substitute “GB”;

(v) omit “EU individual vehicle approval or a national”;

(vi) for “Member States” substitute “Secretary of State”;

(e) in point 2.5, omit “EU individual vehicle approval and national”;

(f) in point 3.1—

(i) in the opening words, omit “granted by France”;

(ii) in points (a) to (d), at the beginning of the example approval certificate numbers, for “e2” substitute “g11”;

(g) in point 3.2—

(i) for “EU whole” substitute “GB whole”;

(ii) omit “by Ireland”;

(iii) at the beginning of the example number, for “e24” substitute “g11”;

(h) in point 3.3—

(i) for “an EU type-approval” substitute “a GB type-approval”;

(ii) for “small” substitute “medium”;

(iii) omit “by Luxembourg”;

(iv) at the beginning of the example number, for “e13” substitute “g11”;

(i) in point 3.4—

(i) omit “national”;

(ii) omit “by the Netherlands”;

(iii) at the beginning of the example number, for “e4” substitute “g11”;

(j) omit point 3.5;

(k) in point 3.6—

(i) “a national” substitute “an”;

(ii) omit “by Austria”;

(iii) at the beginning of the example number, for “e12” substitute “g11”;

(l) in point 4, in the second subparagraph, for “EU type-approval” substitute “GB type-approval”;

(m) in point 4.6.1—

(i) omit “by Germany”;

(ii) at the beginning of the example number, for “e1” substitute “g11”;

(n) in point 4.6.2—

(i) omit “by Croatia”;

(ii) at the beginning of the example number, for “e25” substitute “g11”.

(6) In Annex V (EU type-approval mark of components and separate technical units)—

(a) in the heading, and in point 1, for “EU type-approval” substitute “GB type-approval”;

(b) for point 1.1, substitute—

“1.1.   A rectangle surrounding the lower-case letter ‘g’, followed by the number 11.”;

(c) in point 3—

(i) omit “by Belgium”;

(ii) for the image, substitute—

“

”

(d) in point 4—

(i) in the second subparagraph—

(aa) in the opening words, for “EU type-approvals” substitute “GB type-approvals”;

(bb) in the final sentence in point (b), for the words after “lower-case letter ‘e’” to the end, substitute “the lower-case letter ‘g’ shall be used, followed by the number 11”,

(ii) in the third subparagraph, omit “by Germany”;

(iii) for the image following the third subparagraph, substitute—

“

”

(7) In Annex VI (template for the test result sheet)—

(a) in the opening sentence, for “EU type-approval” substitute “GB type-approval”;

(b) in each table in point 4, in the heading of the first column, for “Decision” substitute “Document”.

(8) In Annex VII (format of test reports for type-approval), in paragraph 2, for the words from “one of the official languages” to the end, substitute “English”.

(9) In Annex VIII (certificate of conformity in paper format)—

(a) in point 1.4, omit the words in brackets;

(b) in Part 1 of the Appendix—

(i) in the Section relating to Model A1, in the text below point 0.11, for “can be permanently registered in Member States having” substitute “is suitable for”;

(ii) in the Section relating to Model A2, in the text below point 0.11, for “can be permanently registered in Member States having” substitute “is suitable for”;

(iii) in the Section relating to Model B, Part 1, in point 0.11(c), for “can be permanently registered in Member States having” substitute “is suitable for”;

(c) in Part 2 of the Appendix—

(i) in Vehicle Categories M2, M3, N2, and N3, in each case in point 5.2, for “complying with Article 9a of Directive 96/53/EC” substitute “complying with Appendix 5 of Annex I to Commission Regulation (EU) 1230/2012”;

(ii) in Vehicle Category O3 and O4, in point 17—

(aa) for the second sentence, substitute—

“Only for national traffic, the lower-case letter ‘g’ followed by the number 11”.

(bb) omit the third sentence.

Commission Implementing Regulation (EU) 2020/1812

87.—(1) Commission Implementing Regulation (EU) 2020/1812 is amended as follows.

(2) Omit Articles 1 (common secure electronic exchange system), 2 (security measures) and 3 (procedure for the exchange of type-approval information).

(3) In Article 4 (list of EU type-approvals)—

(a) In the heading, for “EU” substitute “GB”;

(b) in paragraph 1—

(i) for “Member States make” substitute “the Secretary of State makes”;

(ii) for “lists of EU type-approvals” substitute “list of GB type-approvals”;

(iii) omit “using ETAES”;

(iv) for “they shall” substitute “the Secretary of State must”;

(v) for “Member States shall” substitute “The Secretary of State must”;

(c) in paragraph 2—

(i) omit point (a);

(ii) for “EU type-approval”, each time it occurs, substitute “GB type-approval”;

(d) omit paragraph 3.

(4) After Article 5, omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”

(1)

S.I. 2008/1597.

(2)

S.I. 2020/818, amended by S.I. 2020/1393.

(3)

EUR 765/2008.

(4)

OJ L 151, 14.6.2018, p. 1.

(5)

2020 c. 27.

(6)

2018 c. 16.

(7)

1988 c. 52. Subsection (1A) was inserted by S.I. 2019/648.

(8)

S.I. 1986/1078.

(9)

S.I. 1998/3111.

(10)

EUR 2019/631.

(11)

EUR 2020/683.

(12)

S.I. 1986/1082, amended by S.I. 1994/2867, 2001/55 and 2009/3046.

(13)

S.I. 1998/3111.

(14)

S.I. 2001/561, amended by S.I. 2001/1079 and 2002/2687.

(15)

EUR 2016/1628.

(16)

EUR 2017/1151.

(17)

EUR 2018/858.

(18)

EUR 2020/683.

(19)

EUR 2018/858, as amended by S.I. 2019/648, 2020/818 and 2020/1393.

(20)

EUR 2020/631.

(21)

EUR 2010/406.

(22)

OJ L 231, 26.8.2016, p. 41.

(23)

OJ L 183, 10.7.2015, p. 91.

(24)

OJ L 35, 8.2.2018, p. 1.

(25)

EUR 2011/19.

(26)

OJ L 292, 10.11.2010, p. 2.

(27)

OJ L 117, 6.4.2021, p. 1.

(28)

OJ L 151, 14.6.2018, p. 1.

(29)

OJ L 163, 26.5.2020, p. 1.

(30)

OJ L 8, 12.1.2011, p. 1.

(31)

OJ L 117, 6.4.2021, p. 1.

(32)

EUR 2012/1230.

(33)

OJ L 34, 9.2.2011, p. 2.

(34)

OJ L 117, 6.4.2021, p. 1.

(35)

OJ L 269, 26.10.2018, p. 36.

(36)

S.I. 1999/3107.

(37)

OJ L 52, 23.2.2018, p. 1.

(38)

OJ L 52, 23.2.2018, p. 1.

(39)

OJ L 42, 18.2.2016, p. 1.

(40)

S.I. 1998/3111.

(41)

S.I. 1986/1078.

(42)

S.I. 2003/1998.

(43)

S.I. 1998/3111.

(44)

S.I. 2016/1152.

(45)

OJ L 52, 23.2.2018, p. 1.

(46)

OJ L 230, 31.8.2010, p. 81.

(47)

OJ L 60, 2.3.2013, p. 1.

(48)

1988 (c. 52). Subsection (1A) (S.I. 2020/1393) was inserted, with (1B) and (1C), into section 55 by S.I. 2019/648, as amended by S.I. 2020/818 and 1393. Subsection (1D) is inserted by these Regulations.

(49)

OJ L 60, 2.3.2013, p. 52.

(50)

1988 (c. 52). Subsection (1A) was inserted, with (1B) and (1C), into section 55 by S.I. 2019/648, as amended by S.I 2020/818 and 1393.

(51)

OJ L 42, 23.2.1970, p. 16.

(52)

1988 c. 52. Subsection (1A) was inserted by S.I. 2019/648.

(53)

2003 c. 21.

(54)

2018 c. 12.

(55)

EUR 2016/679.

(56)

S.I. 2003/2426.

(57)

2018 c. 12.

(58)

S.I. 2013/2426.

(59)

EUR 2016/679.

(60)

EUR 2019/631.

(61)

EUR 2007/715.

(62)

S.I. 1999/1307.

(63)

S.I. 1986/1078. Paragraphs 36A and 36B were inserted by S.I. 1988/271 and 1991/1527 respectively.

(64)

OJ L 172, 3.7.2015, p. 1.