1.Without prejudice to Articles 24a.03 and 24a.04, craft which do not fully comply with the provisions of this Directive must be adapted to comply with provisions which enter into force after the first issue of their Community certificate or other traffic licence in accordance with the transitional provisions listed in the table below.
2.The following definitions apply in the table below:
‘NRC’: The provision does not apply to craft which are already operating, unless the parts concerned are replaced or converted, i.e. the provision applies only to Newly-built craft and to the Replacement or Conversion of the parts or areas concerned. If existing parts are replaced by replacement parts using the same technology and of the same type, this does not constitute replacement (‘R’) within the meaning of the transitional provisions.
‘Issue or renewal of the Community certificate’: The provision must be complied with by the time of the issue or next renewal of the Community certificate after 30 December 2008. If the certificate expires between 30 December 2008 and the day before 30 December 2009, that requirement is, however, only mandatory from 30 December 2009.
| a The provision applies to vessels laid down 2 years after the date of entry into force of this Directive and to vessels in service with the following proviso: The requirements of Article 11.04 must be complied with where the entire hold area is renewed. Where a conversion modifying the clear width of the side deck covers the entire length of the side decks, (a) Article 11.04 must be complied with if the clear width of the side deck before the conversion to a height of 0,90 m, or the clear width above that height is to be reduced, (b) the clear width of the side deck before the conversion, to a height of 0,90 m, or the clear width above that height must not be lower than the measurements indicated in Article 11.04. | ||
| Article and paragraph | Content | Deadline and comments |
|---|---|---|
| CHAPTER 3 | ||
| 3.03(1)(a) | Location of collision bulkhead | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 3.03(2) | Accommodations | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 3.03(2) | Safety equipment | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 3.03(4) | Gastight separation | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 3.03(5), second paragraph | Monitoring of doors in the aft-peak bulkhead | |
| 3.03(7) | Anchors not protruding in foresections of vessels | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 3.04(3), second sentence | Insulation in engine rooms | NRC, at the latest on issue or renewal of the Community certificate |
| 3.04(3), third and fourth sentences | Openings and locking devices | NRC, at the latest on issue or renewal of the Community certificate |
| 3.04(6) | Exits from spaces classified as engine rooms as a result of this Directive | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| CHAPTER 4 | ||
| 4.04 | Draught marks | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| CHAPTER 5 | ||
| 5.06(1), first sentence | Minimum speed | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| CHAPTER 6 | ||
| 6.01(1) | Manoeuvrability required by Chapter 5 | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 3 | Permanent lists and ambient temperatures | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 6.01(7) | Design of rudder stocks | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 6.02(2) | Placing in service of second drive unit by means of a single operation | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 3 | Manoeuvrability required by Chapter 5 ensured by second drive unit/manual service | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 6.03(1) | Connection of other power consumers to the hydraulic steering apparatus drive unit | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 2 | Separate hydraulic reservoirs | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 6.05(1) | Wheel of manual drive not driven by powered drive unit | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 6.06(1) | Two independent actuation systems | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 6.07(2)(a) | Monitoring devices for level of hydraulic reservoir and service pressure | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| (e) | Monitoring of buffer devices | NRC, at the latest on issue or renewal of the Community certificate |
| 6.08(1) | Requirements for electronic equipment according to Article 9.20 | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| CHAPTER 7 | ||
| 7.02(2) to (7) | Unobstructed view from the wheelhouse,except the following sections: | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 7.02(3), second paragraph | Unobstructed view in the sightline of the helmsman | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| paragraph 5 | Minimal light transmission of glazing | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 7.03(7) | Shutdown of alarms | NRC, at the latest on issue or renewal of the Community certificate |
| paragraph 8 | Automatic switch to alternative power supply | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 7.04(1) | Control of main engines and steering devices | NRC, at the latest on issue or renewal of the Community certificate |
| 7.04(2) | Control of main engines | If wheelhouses have not been designed for radar navigation by one person: NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 if the direction of motion can be achieved directly; at the latest on issue or renewal of the Community certificate after 30 December 2024 for other engines |
| 7.09 | Alarm system | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 7.12 first paragraph | Retractable wheelhouses | NRC, at the latest on issue or renewal of the Community certificate. Without automatic retraction: NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| second and third paragraphs | NRC, at the latest on issue or renewal of the Community certificate | |
| CHAPTER 8 | ||
| 8.01(3) | Only internal-combustion engines burning fuels having a flashpoint of more than 55 °C | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 8.02(1) | Securing of engines against unintentional starting | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 4 | Protection of machinery parts | NRC, at the latest on issue or renewal of the Community certificate |
| 8.03(2) | Monitoring devices | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 3 | Automatic protection against overspeed | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 5 | Design of shaft bushings | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 8.05(1) | Steel tanks for liquid fuels | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 8.05(2) | Automatic closing of tank valves | NRC, at the latest on issue or renewal of the Community certificate |
| paragraph 3 | No fuel tanks forward of the collision bulkhead | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 4 | No fuel tanks and their fittings above engines or exhaust pipes | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024. Until then, appropriate devices must ensure the safe evacuation of fuels |
| paragraph 6 third to fifth sentences | Installation and measurements of breather pipes and connection pipes | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 7 | Shutoff device to be operated from the deck | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| paragraph 9, first sentence | Capacity-gauging devices to be legible up to maximum filling level | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 13 | Filling level control not only for main engines but also other engines needed for safe operation of the vessel | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 8.06 | Storage of lubricating oil, pipes and accessories | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 8.07 | Storage of oils used in power transmission systems, control and activating systems and heating systems, pipes and accessories | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 8.08( 8) | Simple closing device not sufficient for connection of ballast spaces to drainage pipes for holds capable of carrying ballast | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 8.08( 9) | Gauging devices in hold bilges | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 8.09(2) | Installations for the collection of oily water and used oil stores | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 8.10(3) | Emission limit of 65 dB(A) for stationary craft | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| CHAPTER 9 | ||
| 9.01(1), second sentence | Relevant documents to be submitted to the inspection body | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 9.01(2), second indent | Switching diagrams for main, emergency and distribution switchboard to be kept on board | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 3 | Ambient inside and deck temperatures | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 9.02(1) to (3) | Electricity supply systems | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 9.03 | Protection against physical contact, intrusion of solid objects and the ingress of water | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 9.05(4) | Cross-section of the earthing conductors | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 9.11(4) | Effective ventilation when accumulators are installed in a closed compartment, cabinet or chest | NRC, at the latest on issue or renewal of the Community certificate |
| 9.12 | Switch-gear installations | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 9.12 (3)(b) | Earth detection device capable of giving both visual and audible alarm | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 9.13 | Emergency circuit breakers | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 9.14 | Installation fittings | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 9.14(3), second sentence | Prohibition of single-pole switches in laundries, bathrooms, washrooms and other rooms with wet facilities | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 9.15(2) | Minimum cross-section of 1,5 mm2 per cable | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| paragraph 10 | Cables connected to retractable wheelhouses | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 9.16(3), second sentence | Second circuit | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 9.19 | Alarm and safety systems for mechanical equipment | NRC, at the latest on issue or renewal of the Community certificate 30 December 2029 |
| 9.20 | Electronic equipment | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 9.21 | Electromagnetic compatibility | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| CHAPTER 10 | ||
| 10.01 | Anchor equipment | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 10.02 (2)(a) | Certificate for mooring and other cables | First cable to be replaced on the vessel: NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 Second and third cables: 30 December 2029 |
| 10.03(1) | European standard | At replacement, at the latest 30 December 2024 |
| paragraph 2 | Suitability for Class A, B and C fires | At replacement, at the latest 30 December 2024 |
| paragraph 4 | Relation of CO2 content and size of room | At replacement, at the latest 30 December 2024 |
| 10.03a | Permanently installed fire-fighting systems in accommodation spaces, wheelhouses and passenger spaces | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 10.03b | Permanently installed fire-fighting systems in engine rooms, boiler rooms and pump rooms | CO2 fire-fighting systems permanently installed before 1 October 1985 may remain in use until the issue or renewal of the Community certificate after 30 December 2049 if they comply with the requirements of Article 13.03 of Annex II of Directive 82/714/EEC |
| 10.04 | Application of the European standard to dinghies | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 10.05(2) | Inflatable life jackets | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 Life jackets which are on board on the day before 30 December 2008 can be used until renewal of the Community certificate after 30 December 2024 |
| CHAPTER 11 | ||
| 11.02(4) | Equipment of outer edges of decks, side decks and work stations | NRC, [at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 11.04 | Side decks | First issue or renewal of the Community certificatea after 30 December 2049 where width exceeds 7,30 m |
| 11.05(1) | Access to workplaces | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraphs 2 and 3 | Doors and accesses, exits and passageways where there is more than a 0,50 m difference in floor level | NRC, at the latest on issue or renewal of the Community certificate |
| paragraph 4 | Stairs in working spaces which are manned continuously | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 11.06(2) | Exits and emergency exits | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 11.07(1), second sentence | Ladders, steps and similar devices | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraphs 2 and 3 | NRC, at the latest on issue or renewal of the Community certificate | |
| 11.10 | Hatch covers | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 11.11 | Winches | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2024 |
| 11.12(2) to (6) and (8) to (10) | Cranes: manufacturer's plate, maximum permissible loadings, protection devices, calculation test, inspection by experts, certificates on board | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| 11.13 | Storing of flammable liquids | NRC, at the latest on issue or renewal of the Community certificate |
| CHAPTER 12 | ||
| 12.01(1) | Accommodation for the persons lodging habitually on board | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 12.02(3) | Situation of floors | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 4 | Living and sleeping quarters | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 12.02(5) | Noise and vibration in accommodations | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |
| paragraph 6 | Headroom in accommodations | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 8 | Free floor area of communal living quarters | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 9 | Cubic capacity of rooms | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 10 | Volume of airspace per person | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 11 | Size of doors | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 12(a) and (b) | Situation of stairs | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 13 | Pipes carrying dangerous gases or liquids | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 12.03 | Sanitary installations | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 12.04 | Galleys | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 12.05 | Potable water | NRC, at the latest on issue or renewal of the Community certificate |
| 12.06 | Heating and ventilation | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| 12.07 section 1, second sentence | Other accommodation installations | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| CHAPTER 15 | ||
| Passenger vessels | see Article 8 of this Directive | |
| CHAPTER 15a | ||
| Passenger sailing vessels | see Article 8 of this Directive | |
| CHAPTER 16 | ||
| 16.01(2) | Special winches or equivalent coupling devices | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| paragraph 3, last sentence | Requirements for drive units | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2049 |
| CHAPTER 17 | ||
| Floating equipment | see Article 8 of this Directive | |
| CHAPTER 21 | ||
| Recreational craft | see Article 8 of this Directive | |
| CHAPTER 22b | ||
| 22b.03 | Second independent steering apparatus drive unit | NRC, at the latest on issue or renewal of the Community certificate after 30 December 2029 |