ANNEX IU.K.
1.DIMENSIONSU.K.
The dimensions of the space for mounting the rear registration plate of two or three-wheel motor vehicles(1) are as follows:
1.1. Mopeds and light quadricycles without a body U.K.
1.1.1. Width: 100 mm;U.K.
1.1.2. Height: 175 mm;U.K.
or
1.1.3. Width: 145 mm;U.K.
1.1.4. Height: 125 mm.U.K.
1.2. Motorcycles, tricycles up to a maximum power of 15 kW and quadricycles, other than light quadricycles, without a body U.K.
1.2.1. Width: 280 mm;U.K.
1.2.2. Height: 210 mm.U.K.
1.3. Tricycles with a maximum power exceeding 15 kW, light quadricycles fitted with a body and quadricycles, other than light quadricycles, fitted with a body U.K.
1.3.1.The provisions for passenger cars as set out in Council Directive 70/222/EEC(2) shall apply.U.K.
2.GENERAL LOCATIONU.K.
2.1.The mounting for the rear registration plate must be located at the rear of the vehicle in such a manner that:U.K.
2.1.1.the plate can be positioned within the longitudinal planes passing through the outer extremities of the vehicle.U.K.
3.INCLINATIONU.K.
3.1.The rear registration plate:U.K.
must be at right angles to the median longitudinal plane of the vehicle;
may be inclined from the vertical by not more than 30°, with the vehicle unladen, when the backing plate for the registration number faces upwards;
may be inclined by not more than 15° from the vertical, with the vehicle unladen, when the backing plate for the registration number faces downwards.
4.MAXIMUM HEIGHTU.K.
4.1.No point on the space for mounting the registration plate may be more than 1,5 m above the ground when the vehicle is unladen.U.K.
5.MINIMUM HEIGHTU.K.
5.1.No point on the space for mounting the registration plate shall be less than 0,20 m above the ground or less than the radius of the wheel above the ground if that is less than 0,20 m, when the vehicle is unladen.U.K.
6.GEOMETRIC VISIBILITYU.K.
6.1.The space for mounting the plate must be visible within a space bordered by two dihedrals: one with a horizontal edge defined by two planes passing through the upper and lower horizontal edges of the space for mounting the plate, the angles of which in relation to the horizontal are shown in Figure 1; the other with a perceptibly vertical edge defined by two planes passing through each side of the plate, the angles of which in relation to the median longitudinal plane of the vehicle are shown in Figure 2.U.K.
Appendix 1
Information document in respect of the space for mounting the rear registration plate of a type of two or three-wheel motor vehicle (to be attached to the application for EC component type-approval where this is submitted separately from the application for EC vehicle type-approval)U.K.
Order No (assigned by the applicant):
The application for EC component type-approval in respect of the space for mounting the rear registration plate of a type of two or three-wheel motor vehicle must contain the information set out in Annex II to Directive 2002/24/EC, Part 1, section A, points:
0.1
0.2
0.4 to 0.6
2.2
2.2.1
9.6
9.6.1.
Appendix 2
EC component type-approval certificate in respect of the space for mounting the rear registration plate of a type of two or three-wheel motor vehicle MODEL U.K.
Report No … by technical service … date …
EC component type-approval No … Extension No …
1.Trade mark or name of vehicle …U.K.
2.Vehicle type …U.K.
3.Manufacturer’s name and address …U.K.
…
4.Name and address of manufacturer’s representative (if any) …U.K.
…
5.Date vehicle submitted for test …U.K.
6.EC component type-approval has been granted/refused(3).U.K.
7.Place …U.K.
8.Date …U.K.
9.Signature …U.K.
ANNEX IIU.K.
PART AU.K.
Repealed Directive with its amendment
(referred to in Article 5)
| Council Directive 93/94/EEC | (OJ L 311, 14.12.1993, p. 83). |
| Commission Directive 1999/26/EC | (OJ L 118, 6.5.1999, p. 32). |
PART BU.K.
List of time-limits for transposition into national law and application
(referred to in Article 5)
| a In conformity with Article 4 of Directive 93/94/EEC: From [1 May 1995], Member States may not, for reasons connected with the space for mounting the rear registration plate, prohibit the initial entry into service of vehicles which conform to this Directive.” | ||
| b In conformity with Article 2 of Directive 1999/26/EC: 1.With effect from 1 January 2000, Member States shall not, on grounds relating to the space for mounting the rear registration plate:
if the space for mounting the rear registration plate complies with the requirements of Directive 93/94/EEC as amended by this Directive. 2.With effect from 1 July 2000, Member States shall refuse to grant EC type-approval for any type of two or three-wheel motor vehicle on grounds relating to the space for mounting the rear registration plate if the requirements of Directive 93/94/EEC, as amended by this Directive, are not fulfilled.”. | ||
| Directive | Time-limit for transposition | Date of application |
|---|---|---|
| 93/94/EEC | 30 April 1995 | 1 November 1995a |
| 1999/26/EC | 31 December 1999 | 1 January 2000b |
ANNEX IIIU.K.
Correlation Table
| Directive 93/94/EEC | Directive 1999/26/EC | This Directive |
|---|---|---|
| Articles 1, 2 and 3 | Articles 1, 2 and 3 | |
| Article 2(1) | Article 4(1) | |
| Article 2(2) | Article 4(2) | |
| Article 4(1) | — | |
| Article 4(2) | Article 4(3) | |
| — | Article 5 | |
| — | Article 6 | |
| Article 5 | Article 7 | |
| Annex | Annex I | |
| — | Annex II | |
| — | Annex III |
In the case of mopeds, this is any registration and/or identification plate.
Delete as appropriate.