ANNEX IAdministrative documents for EC type-approval of motor vehicles with regard to wheel guards
PART 1Information document
MODEL
Information document No … relating to the EC type-approval of a motor vehicle with regard to wheel guards.
The following information shall be supplied in triplicate and include a list of contents. Any drawings shall be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, shall show sufficient detail.
If the systems, components or separate technical units referred to in this information document have electronic controls, information concerning their performance shall be supplied.
0.GENERAL
0.1.
Make (trade name of manufacturer): …
0.2.
Type: …
0.2.1.
Commercial name(s) (if available): …
0.3.
Means of identification of type, if marked on the vehicle4: …
0.3.1.
Location of that marking: …
0.4.
Category of vehicle5: …
0.5.
Name and address of manufacturer: …
0.8.
Name(s) and address(es) of assembly plant(s): …
0.9.
Name and address of the manufacturer's representative (if any): …
1.GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE
1.1.
Photographs and/or drawings of a representative vehicle: …
1.3.
Number of axles and wheels: …
1.3.1.
Number and position of axles with twin wheels: …
1.3.2.
Number and position of steered axles: …
1.3.3.
Powered axles (number, position, interconnection): …
2.MASSES AND DIMENSIONS67
2.3.Axle track(s) and width(s):
2.3.1.
Track of each steered axle:8 …
2.3.2.
Track of all other axles:8 …
2.3.3.
Width of the widest rear axle: …
2.3.4.
Width of the foremost axle (measured at the outermost part of the tyres excluding the bulging of the tyres close to the ground): …
2.4.Range of vehicle dimensions (overall)
2.4.1.For chassis without bodywork
2.4.1.2.
Width9: …
2.4.1.3.
Height (in running order)10 (for suspensions adjustable for height, indicate normal running position): …
2.4.2.For chassis with bodywork
2.4.2.2.
Width9: …
2.4.2.3.
Height (in running order)10 (for suspensions adjustable for height, indicate normal running position): …
2.6.
Mass in running order
Mass of the vehicle with bodywork and, in the case of a towing vehicle of category other than M1, with coupling device, if fitted by the manufacturer, in running order, or mass of the chassis or chassis with cab, without bodywork and/or coupling device if the manufacturer does not fit the bodywork and/or coupling device (including liquids, tools, spare wheel, if fitted, and driver and, for buses and coaches, a crew member if there is a crew seat in the vehicle)11 (maximum and minimum for each variant): …
6.SUSPENSION
6.2.1.
Level adjustment: yes/no/optional12
6.6.Tyres and wheels
6.6.1.Tyre/wheel combination(s)
- (a)
for tyres indicate size designation;
- (b)
for wheels indicate rim size(s) and off-set(s)
6.6.1.1.Axles
6.6.1.1.1.
Axle 1: …
6.6.1.1.2.
Axle 2: …
etc.
6.6.4.
Description of the snow traction device(s) and the tyre/wheel combination(s) on the front and/or rear axle(s) suitable for the type of vehicle, as recommended by the manufacturer: …
9.16.Wheel guards
9.16.1.
Brief description of the vehicle with regard to its wheel guards: …
9.16.2.
Detailed drawings of the wheel guards and their position on the vehicle showing the dimensions specified in Figure 1 of Annex II of this Regulation and taking account of the extremes of tyre/wheel combinations: …
Explanatory notes
PART 2EC type-approval certificate
MODEL
Format: A4 (210 × 297 mm)
EC TYPE-APPROVAL CERTIFICATE
Stamp of type-approval authority
Communication concerning:
of a type of vehicle with regard to wheel guards | |
with regard to Regulation (EU) No 1009/2010 as last amended by Regulation (EU) No …/…13 | |
EC type-approval number: … | |
Reason for extension: … | |
Delete where not applicable. | |
SECTION I
0.1.
Make (trade name of manufacturer): …
0.2.
Type: …
0.2.1.
Commercial name(s) (if available): …
0.3.
Means of identification of type, if marked on the vehicle14: …
0.3.1.
Location of that marking: …
0.4.
Category of vehicle15: …
0.5.
Name and address of manufacturer: …
0.8.
Name(s) and address(es) of assembly plant(s): …
0.9.
Name and address of the manufacturer's representative (if any): …
SECTION II
1.
Additional information: see Addendum.
2.
Technical service responsible for carrying out the tests: …
3.
Date of test report: …
4.
Number of test report: …
5.
Remarks (if any): see Addendum.
6.
Place: …
7.
Date: …
8.
Signature: …
- Attachments
Information package
Test report
1.Additional information:
- 1.1.
Brief description of the vehicle type as regards its structure, dimensions, lines and constituent materials: …
- 1.2.
Description of the wheel guards: …
- 1.3.
Tyre/wheel combination(s) (including tyre size, rim size and wheel off-set): …
- 1.4.
Description of the type of snow traction device(s) which may be used: …
- 1.5.
Tyre/wheel combination(s) (including tyre size, rim size and wheel off-set) to be used with the snow traction device(s): …
2.
Permanently driven axle(s): axle 1/axle 2/…16
3.
Suspension height adjustable: yes/no16
4.
5.
Remarks: …