Commission Regulation (EU) No 1009/2010Show full title

Commission Regulation (EU) No 1009/2010 of 9 November 2010 concerning type-approval requirements for wheel guards of certain motor vehicles and implementing Regulation (EC) No 661/2009 of the European Parliament and of the Council concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor (Text with EEA relevance)

ANNEX IU.K.Administrative documents for [F1GB type-approval] of motor vehicles with regard to wheel guards

Textual Amendments

PART 1U.K.Information document

MODELU.K.

Information document No … relating to the [F2GB type-approval] of a motor vehicle with regard to wheel guards.

Textual Amendments

The following information shall be supplied in triplicate and include a list of contents. Any drawings shall be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, shall show sufficient detail.

If the systems, components or separate technical units referred to in this information document have electronic controls, information concerning their performance shall be supplied.

0.GENERALU.K.

0.1.Make (trade name of manufacturer): …U.K.
0.2.Type: …U.K.
0.2.1.Commercial name(s) (if available): …U.K.
0.3.Means of identification of type, if marked on the vehicle(1): …U.K.
0.3.1.Location of that marking: …U.K.
0.4.Category of vehicleM1: …U.K.

Marginal Citations

M1Classified according to the definitions set out in [Article 4 of Regulation (EU) 2018/858] [Editorial note: words in Annex 1 Pt. 1 footnote substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 61(6)(b)(ii)]

0.5.Name and address of manufacturer: …U.K.
0.8.Name(s) and address(es) of assembly plant(s): …U.K.
0.9.Name and address of the manufacturer's representative (if any): …U.K.

1.GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLEU.K.

1.1.Photographs and/or drawings of a representative vehicle: …U.K.
1.3.Number of axles and wheels: …U.K.
1.3.1.Number and position of axles with twin wheels: …U.K.
1.3.2.Number and position of steered axles: …U.K.
1.3.3.Powered axles (number, position, interconnection): …U.K.

2.MASSES AND DIMENSIONS(2) (3) U.K.

2.3.Axle track(s) and width(s):U.K.
2.3.1.Track of each steered axle:(4) …U.K.
2.3.2.Track of all other axles:(4) …U.K.
2.3.3.Width of the widest rear axle: …U.K.
2.3.4.Width of the foremost axle (measured at the outermost part of the tyres excluding the bulging of the tyres close to the ground): …U.K.
2.4.Range of vehicle dimensions (overall)U.K.
2.4.1.For chassis without bodyworkU.K.
2.4.1.2.Width(5): …U.K.
2.4.1.3.Height (in running order)(6) (for suspensions adjustable for height, indicate normal running position): …U.K.
2.4.2.For chassis with bodyworkU.K.
2.4.2.2.Width(5): …U.K.
2.4.2.3.Height (in running order)(6) (for suspensions adjustable for height, indicate normal running position): …U.K.
2.6.Mass in running orderU.K.

Mass of the vehicle with bodywork and, in the case of a towing vehicle of category other than M1, with coupling device, if fitted by the manufacturer, in running order, or mass of the chassis or chassis with cab, without bodywork and/or coupling device if the manufacturer does not fit the bodywork and/or coupling device (including liquids, tools, spare wheel, if fitted, and driver and, for buses and coaches, a crew member if there is a crew seat in the vehicle)(7) (maximum and minimum for each variant): …

6.SUSPENSIONU.K.

6.2.1.Level adjustment: yes/no/optional(8)U.K.
6.6.Tyres and wheelsU.K.
6.6.1.Tyre/wheel combination(s)U.K.
(a)

for tyres indicate size designation;

(b)

for wheels indicate rim size(s) and off-set(s)

6.6.1.1.AxlesU.K.
6.6.1.1.1.Axle 1: …U.K.
6.6.1.1.2.Axle 2: …U.K.

etc.

6.6.4.Description of the snow traction device(s) and the tyre/wheel combination(s) on the front and/or rear axle(s) suitable for the type of vehicle, as recommended by the manufacturer: …U.K.
9.16.Wheel guardsU.K.
9.16.1.Brief description of the vehicle with regard to its wheel guards: …U.K.
9.16.2.Detailed drawings of the wheel guards and their position on the vehicle showing the dimensions specified in Figure 1 of Annex II of this Regulation and taking account of the extremes of tyre/wheel combinations: …U.K.

Explanatory notesU.K.

PART 2U.K. [F3GB type-approval] certificate

MODELU.K.Format: A4 (210 × 297 mm)U.K. [F4GB TYPE-APPROVAL] CERTIFICATEU.K.

Stamp of type-approval authority

Communication concerning:

a

Delete where not applicable.

  • [F4GB type-approval]a

  • extension of [F4GB type-approval]a

  • refusal of [F4GB type-approval]a

  • withdrawal of [F4GB type-approval]a

of a type of vehicle with regard to wheel guards
with regard to Regulation (EU) No 1009/2010 [F5as it forms part of domestic law, and as last amended by S.I. …./….] a
[F4GB type-approval] number: …
Reason for extension: …

Textual Amendments

SECTION IU.K.

0.1.Make (trade name of manufacturer): …U.K.
0.2.Type: …U.K.
0.2.1.Commercial name(s) (if available): …U.K.
0.3.Means of identification of type, if marked on the vehicle(9): …U.K.
0.3.1.Location of that marking: …U.K.
0.4.Category of vehicle(10)M2: …U.K.

Marginal Citations

M2As defined in [Article 4 of Regulation (EU) 2018/858] [Editorial note: words in Annex 1 Pt. 2 footnote substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 61(6)(c)(iii)]

0.5.Name and address of manufacturer: …U.K.
0.8.Name(s) and address(es) of assembly plant(s): …U.K.
0.9.Name and address of the manufacturer's representative (if any): …U.K.

SECTION IIU.K.

1.Additional information: see Addendum.U.K.
2.Technical service responsible for carrying out the tests: …U.K.
3.Date of test report: …U.K.
4.Number of test report: …U.K.
5.Remarks (if any): see Addendum.U.K.
6.Place: …U.K.
7.Date: …U.K.
8.Signature: …U.K.
Attachments

:

Information package

Test report

Textual Amendments

Textual Amendments

Addendumto [F6GB type-approval] certificate No …

Textual Amendments

1.Additional information:U.K.

1.1.

Brief description of the vehicle type as regards its structure, dimensions, lines and constituent materials: …

1.2.

Description of the wheel guards: …

1.3.

Tyre/wheel combination(s) (including tyre size, rim size and wheel off-set): …

1.4.

Description of the type of snow traction device(s) which may be used: …

1.5.

Tyre/wheel combination(s) (including tyre size, rim size and wheel off-set) to be used with the snow traction device(s): …

2.Permanently driven axle(s): axle 1/axle 2/…(11)U.K.

3.Suspension height adjustable: yes/no(11)U.K.

4.Wheel guards detachable/not detachable(11) as a unit/in parts(11)U.K.

5.Remarks: …U.K.

(1)

If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information document, such characters shall be represented in the documentation by the symbol ‘?’ (e.g. ABC??123??).

(2)

Where there is one version with a normal cab and another with a sleeper cab, both sets of masses and dimensions are to be stated.

(3)

Standard ISO 612: 1978 - Road vehicles - Dimensions of motor vehicles and towed vehicles - terms and definitions.

(4)

(g4)Term No 6.5.U.K.

(5)

(g7)Term No 6.2.U.K.

(6)

(g8)Term No 6.3.U.K.

(7)

The mass of the driver and, if applicable, of the crew member is assessed at 75 kg (subdivided into 68 kg occupant mass and 7 kg luggage mass according to ISO Standard 2416 - 1992), the fuel tank is filled to 90 % and the other liquid containing systems (except those for used water) to 100 % of the capacity specified by the manufacturer.

(8)

Delete where not applicable.

(9)

If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information document, such characters shall be represented in the documentation by the symbol ‘?’ (e.g. ABC??123??).

(10)

As defined in Directive 2007/46/EC, Annex II, Section A.

(11)

Delete as appropriate.