ANNEX IAdministrative documents for EC type-approval of motor vehicles with regard to windscreen defrosting and demisting systems
PART 1Information document
MODEL
Information document No … relating to the EC type-approval of a motor vehicle with regard to windscreen defrosting and demisting systems.
The following information shall be supplied in triplicate and include a list of contents. Any drawings shall be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, shall show sufficient detail.
If the systems, components or separate technical units referred to in this annex have electronic controls, information concerning their performance shall be supplied.
0.GENERAL
0.1.
Make (trade name of manufacturer): …
0.2.
Type: …
0.2.1.
Commercial name(s) (if available): …
0.3.
Means of identification of type, if marked on the vehicle5: …
0.3.1.
Location of that marking: …
0.4.
Category of vehicle6: …
0.5.
Name and address of manufacturer: …
0.8.
Name(s) and address(es) of assembly plant(s): …
0.9.
Name and address of the manufacturer’s representative (if any): …
1.GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE
1.1.
Photographs and/or drawings of a representative vehicle: …
1.6.
Position and arrangement of the engine: …
1.8.
Hand of drive: left/right7.
3.POWER PLANT8
3.1.
Manufacturer of the engine: …
3.1.1.
Manufacturer’s engine code (as marked on the engine or other means of identification): …
3.2.Internal combustion engine
3.2.1.Specific engine information
3.2.1.1.
3.2.1.2.
Number and arrangement of cylinders: …
3.2.1.3.
Engine capacity9: …cm3
3.2.1.6.
Normal engine idling speed10: … min–1
3.2.1.8.
Maximum net power11: …kW at … min–1 (manufacturer’s declared value)
3.2.2.Fuel
3.2.2.1.
3.2.5.Electrical system
3.2.5.1.
Rated voltage: … V, positive/negative ground7
3.2.5.2.Generator
3.2.5.2.1.
Type: …
3.2.5.2.2.
Nominal output: …VA
3.2.7.
Cooling system: liquid/air7
3.2.7.1.
Nominal setting of the engine temperature control mechanism: …
3.2.7.2.
Liquid
3.2.7.2.1.
Nature of liquid: …
3.2.7.2.2.
Circulating pump(s): yes/no7
3.2.7.2.3.
Characteristics: … or
3.2.7.2.3.1.
Make(s): …
3.2.7.2.3.2.
Type(s): …
3.2.7.2.4.
Drive ratio(s): …
3.2.7.2.5.
Description of the fan and its drive mechanism: …
3.2.7.3.Air
3.2.7.3.1.
Fan: yes/no7
3.2.7.3.2.
Characteristics: … or
3.2.7.3.2.1.
Make(s): …
3.2.7.3.2.2.
Type(s): …
3.3.Electric motor
3.3.1.
Type (winding, excitation) …
3.3.1.1.
Maximum hourly output: … kW
3.3.1.2.
Operating voltage: … V
3.3.2.Battery
3.3.2.1.
Number of cells: …
3.3.2.2.
Mass: … kg
3.3.2.3.
Capacity: … Ah (Amp-hours)
3.3.2.4.
Position: …
3.4.Engine or motor combination
3.4.1.
Hybrid electric vehicle: yes/no7
3.4.2.
Category of hybrid electric vehicle: off-vehicle charging/not off-vehicle charging:7
3.4.3.
Operating mode switch: with/without7
3.4.3.1.Selectable modes
3.4.3.1.1.
Pure electric: yes/no7
3.4.3.1.2.
Pure fuel consuming: yes/no7
3.4.3.1.3.
Hybrid modes: yes/no7 (if yes, short description): …
3.4.4.
Description of the energy storage device: (battery, capacitor, flywheel/generator)
3.4.4.1.
Make(s): …
3.4.4.2.
Type(s): …
3.4.4.3.
Identification number: …
3.4.4.4.
Kind of electrochemical couple: …
3.4.4.5.
Energy: … (for battery: voltage and capacity Ah in 2 h, for capacitor: J, …)
3.4.4.6.
Charger: on board/external/without7
3.6.Temperatures permitted by the manufacturer
3.6.1.Cooling system
3.6.1.1.
Liquid cooling, maximum temperature at outlet: … K
3.6.1.2.
Aircooling
3.6.1.2.1.
Reference point: …
3.6.1.2.2.
Maximum temperature at reference point: … K
3.6.2.
Maximum outlet temperature of the inlet intercooler: … K
3.6.3.
Maximum exhaust temperature at the point in the exhaust pipe(s) adjacent to the outer flange(s) of the exhaust manifold or turbocharger: … K
9.BODYWORK
9.1.
Type of bodywork using the codes defined in Part C of Annex II of Directive 2007/46/EC: …
9.2.
Materials used and methods of construction: …
9.3.Occupant doors, latches and hinges
9.3.1.
Door configuration and number of doors: …
9.4.Field of vision
9.4.1.
Particulars of the primary reference marks in sufficient detail to enable them to be readily identified and the position of each in relation to the others and to the R-point to be verified: …
9.4.2.
Drawing(s) or photograph(s) showing the location of component parts within the 180° forward field of vision: …
9.5.Windscreen and other windows
9.5.1.Windscreen
9.5.1.1.
Materials used: …
9.5.1.2.
Method of mounting: …
9.5.1.3.
Angle of inclination: …
9.5.1.4.
Type-approval number(s): …
9.5.1.5.
Windscreen accessories and the position in which they are fitted together with a brief description of any electrical/electronic components involved: …
9.6.Windscreen wiper(s)
9.6.1.
Detailed technical description (including photographs or drawings): …
9.7.Windscreen washer
9.7.1.
Detailed technical description (including photographs or drawings) or, if approved as separate technical unit, type-approval number: …
9.8.Defrosting and demisting
9.8.1.
Detailed technical description (including photographs or drawings): …
9.8.2.
Maximum electrical consumption: …kW
9.10.Interior arrangement
9.10.1.Interior protection for occupants
9.10.1.1.
Layout drawing or photographs showing the position of the attached sections or views: …
9.10.1.3.
Photographs, drawings and/or an exploded view of the interior fittings, showing the parts in the passenger compartment and the materials used (with the exception of interior rear view mirrors), arrangement of controls, roof and opening roof, backrest, seats and the rear part of seats: …
9.10.3.Seats
9.10.3.1.
Number of seating positions13: …
9.10.3.1.1.
Location and arrangement: …
9.10.3.5.
Coordinates or drawing of the R-point
9.10.3.5.1.
Driver’s seat: …
9.10.3.6.
Design torso angle
9.10.3.6.1.
Driver’s seat: …
Explanatory notes