ANNEX IStandard models for the information document and the EC type-approval certificate
PART 1Information document
MODEL
Information document No … relating to the EC type-approval of a vehicle with regard to lane departure warning systems.
The following information shall be supplied in triplicate and include a list of contents. Any drawings shall be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, shall show sufficient detail.
If the systems, components or separate technical units referred to in this Annex have electronic controls, information concerning their performance shall be supplied.
0.GENERAL
0.1.
Make (trade name of manufacturer): …
0.2.
Type: …
0.2.0.1.
Chassis: …
0.2.0.2.
Bodywork/complete vehicle: …
0.2.1.
Commercial name(s) (if available): …
0.3.
Means of identification of type, if marked on the vehicle3: …
0.3.0.1.
Chassis: …
0.3.0.2.
Bodywork/complete vehicle: …
0.3.1.
Location of that marking: …
0.3.1.1.
Chassis: …
0.3.1.2.
Bodywork/complete vehicle: …
0.4.
Category of vehicle4: …
0.5.
Name and address of manufacturer: …
0.6.
Location and method of attachment of statutory plates and location of vehicle identification number: …
0.6.1.
On the chassis: …
0.6.2.
On the bodywork: …
0.9.
Name and address of the manufacturer’s representative (if any): …
1.GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE
1.1.
Photographs and/or drawings of a representative vehicle: …
1.2.
Dimensional drawing of the whole vehicle: …
1.3.
Number of axles and wheels: …
1.3.1.
Number and position of axles with twin wheels: …
1.3.2.
Number and position of steered axles: …
1.3.3.
Powered axles (number, position, interconnection): …
1.8.
Hand of drive: left/right5.
2.MASSES AND DIMENSIONS67(in kg and mm) (Refer to drawing where applicable)
2.1.Wheelbase(s) (fully loaded)8
2.1.1.
Two axle vehicles: …
2.1.1.1.Vehicles with three or more axles
2.3.Axle track(s) and width(s)
2.3.1.
Track of each steered axle10: …
2.3.2.
Track of all other axles10: …
2.3.3.
Width of the widest rear axle: …
2.3.4.
Width of the foremost axle (measured at the outermost part of the tyres excluding the bulging of the tyres close to the ground): …
2.4.Range of vehicle dimensions (overall)
2.4.1.For chassis without bodywork
2.4.1.1.
Length11: …
2.4.1.1.1.
Maximum permissible length: …
2.4.1.1.2.
Minimum permissible length: …
2.4.1.2.
Width13: …
2.4.1.2.1.
Maximum permissible width: …
2.4.1.2.2.
Minimum permissible width: …
2.4.2.For chassis with bodywork
2.4.2.1.
Length11: …
2.4.2.1.1.
Length of the loading area: …
2.4.2.2.
Width13: …
2.4.3.For bodywork approved without chassis (vehicles M2 and M3)
2.4.3.1.
Length11: …
2.4.3.2.
Width13: …
2.6.Mass in running order
Mass of the vehicle with bodywork and, in the case of a towing vehicle of category other than M1, with coupling device, if fitted by the manufacturer, in running order, or mass of the chassis or chassis with cab, without bodywork and/or coupling device if the manufacturer does not fit the bodywork and/or coupling device (including liquids, tools, spare wheel, if fitted, and driver and, for buses and coaches, a crew member if there is a crew seat in the vehicle)14 (maximum and minimum for each variant): …
4.7.
Maximum vehicle design speed (in km/h)15: …