Commission Implementing Regulation (EU) 2017/1Show full title

CHAPTER 1 U.K. GENERAL PROVISIONS

Article 1 U.K. Subject matter

This Regulation lays down rules on watercraft identification, in particular rules on assignment and administration of manufacturer's codes.

Article 2 U.K. Definitions

For the purpose of this Regulation, the following definitions shall apply:

(a)

[F1 ‘UK national body’ means a body appointed by the Secretary of State for assigning the unique code of the manufacturer;]

(b)

‘country where the manufacturer is established’ means the country where the manufacturer has its registered office, in case of a legal person, or a permanent address, in case of a natural person;

(c)

[F2 ‘UK national register’ means the register held by or on behalf of the Secretary of State, where the unique code of manufacturer for manufacturers established in the United Kingdom is recorded;]

(d)

[F3 ‘UK third country register’ means the register held by or on behalf of the Secretary of State, where the unique code of manufacturer for manufacturers established outside of the United Kingdom is recorded;]

(e)

F4 ...

(f)

[F5 ‘approved bodies’ register' means the register held by or on behalf of the Secretary of State where the post-construction assessment identification code is recorded.]

Textual Amendments

F1 Art. 2(a) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 56(a) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F2 Art. 2(c) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 56(b) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F3 Art. 2(d) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 56(c) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F4 Art. 2(e) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 56(d) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F5 Art. 2(f) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 56(e) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

CHAPTER 2 U.K. COMPOSITION OF THE WATERCRAFT IDENTIFICATION NUMBER

Article 3 U.K. Watercraft identification number

1. A watercraft identification number (WIN) shall consist of the following elements in the following order:

(a) the country code of the manufacturer indicating where the manufacturer is established;

(b) the unique code of the manufacturer assigned by [F6 or on behalf of the Secretary of State]; F7 ...

(c) a unique serial number assigned by the manufacturer for identification of the watercraft and used only once by that manufacturer; however the same combination of characters may be used also by another manufacturer with the distinctive element being the combination with the unique code of manufacturer and the country code of the manufacturer;

(d) month and year of production;

(e) model year which corresponds to the year when the specific watercraft is intended to be placed on the [F8 United Kingdom] market.

2. The composition of the WIN shall comply with the second paragraph of [F9 paragraph 2.1 of Schedule 1 to the Recreational Craft Regulations 2017].

Textual Amendments

F6 Words in Art. 3(1)(b) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 57(a)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F7 Words in Art. 3(1)(b) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 57(a)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F8 Words in Art. 3(1)(e) inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 57(b) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F9 Words in Art. 3(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 57(c) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

CHAPTER 3 U.K. ASSIGNMENT AND ADMINISTRATION OF THE UNIQUE CODE OF THE MANUFACTURER

Article 4 U.K. Assignment of the unique code of the manufacturer

1. The unique code of the manufacturer shall be assigned by the [F10 UK national body or, if none is designated, the Secretary of State] following a request by a manufacturer or its authorised representative in accordance with Article 6 or 7.

2. The unique code for a manufacturer shall be generated and assigned only once by the [F11 UK national body or the Secretary of State]. Each manufacturer shall have only one unique code for use over the [F12 United Kingdom] market.

Textual Amendments

F10 Words in Art. 4(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 58(a) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F11 Words in Art. 4(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 58(b)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F12 Words in Art. 4(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 58(b)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

Article 5 U.K. [F13 UK national body] for assigning the unique code of the manufacturer

1. [F14 The Secretary of State may designate the UK] national body responsible for assigning the unique code of the manufacturer.

F15 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

[F16 3. In the absence of a designation under paragraph 1, the Secretary of State is responsible for assigning the unique code of the manufacturer.]

Textual Amendments

F13 Words in Art. 5 heading substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 59(a) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F14 Words in Art. 5(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 59(b) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F15 Art. 5(2) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 59(c) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F16 Art. 5(3) inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 59(d) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

Article 6 U.K. Procedure for assignment of the unique code of the manufacturer to a [F17 manufacturer established in the United Kingdom]

[F18 1. A manufacturer established in the United Kingdom must, before placing a watercraft on the market of Great Britain, submit an application in English for the assignment of the unique code of the manufacturer, to the UK national body or, if none is designated, the Secretary of State.]

2. The application referred to in paragraph 1 shall be accompanied by a copy of a document that proves that the manufacturer is established in [F19 the United Kingdom], in [F20 English].

3. The [F21 UK national body or, if none is designated, the Secretary of State], after having verified the application, shall assign the unique code of the manufacturer in compliance with Article 4.

4. [F22 The Secretary of State] shall ensure that the unique code of the manufacturer is registered in [F23 the UK national register]. F24 ...

Textual Amendments

F17 Words in Art. 6 heading substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 60(a) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F18 Art. 6(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 60(b) (as amended by S.I. 2020/676, regs. 1(1), 2, 4(16)(d)); 2020 c. 1, Sch. 5 para. 1(1)

F19 Words in Art. 6(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 60(c)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F20 Word in Art. 6(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 60(c)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F21 Words in Art. 6(3) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 60(d) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F22 Words in Art. 6(4) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 60(e)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F23 Words in Art. 6(4) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 60(e)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F24 Words in Art. 6(4) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 60(e)(iii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

Article 7 U.K. Procedure for assignment of the unique code of the manufacturer to a manufacturer established [F25 outside of the United Kingdom]

1. A manufacturer established [F26 outside of the United Kingdom] or its authorised representative shall, before placing a watercraft on the [F27 United Kingdom] market, submit an application, in [F28 English], for the assignment of the unique code of the manufacturer to the [F29 UK national body or, if none is designated, the Secretary of State].

2. The application referred to in paragraph 1 shall be accompanied by a copy of a document [F30 in English] that proves [F31 in which country the manufacturer is established].

3. Upon receipt of an application from a manufacturer, the [F32 UK national body or, if none is designated, the Secretary of State] shall verify in the [F33 UK third country register] the availability of the codes combination in order to ensure that it is the first time the manufacturer has submitted an application F34 ....

F35 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5. The [F36 UK national body or, if none is designated, the Secretary of State] having verified the application shall assign the unique code of the manufacturer to the manufacturer in compliance with Article 4. F37 ...

[F38 6. When assigning the unique code of the manufacturer to a manufacturer established outside of the United Kingdom, the UK national body or, if none is designated, the Secretary of State shall register that code and the name and address of the manufacturer in the UK third country register.]

Textual Amendments

F25 Words in Art. 7 heading substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(a) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F26 Words in Art. 7(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(a) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F27 Words in Art. 7(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(b)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F28 Word in Art. 7(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(b)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F29 Words in Art. 7(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(b)(iii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F30 Words in Art. 7(2) inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(c)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F31 Words in Art. 7(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(c)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F32 Words in Art. 7(3) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(d)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F33 Words in Art. 7(3) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(d)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F34 Words in Art. 7(3) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(d)(iii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F35 Art. 7(4) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(e) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F36 Words in Art. 7(5) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(f)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F37 Words in Art. 7(5) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(f)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F38 Art. 7(6) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 61(g) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

Article 8 U.K. Procedure in case of post-construction assessment

1. In case of post-construction assessment, referred to in [F39 regulations 42, 43 and 48 of the Recreational Craft Regulations 2017], where the [F40 approved] body has to affix under [F41 its] responsibility the watercraft identification number, the unique code of manufacturer is indicated by the post-construction assessment identification code and shall be assigned by the [F42 Secretary of State].

2. When assigning the post-construction assessment identification code the [F43 approved] bodies shall have it registered in the [F43 approved] bodies' register.

Textual Amendments

F39 Words in Art. 8(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 62(a)(i) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F40 Word in Art. 8(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 62(a)(ii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F41 Word in Art. 8(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 62(a)(iii) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F42 Words in Art. 8(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 62(a)(iv) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F43 Word in Art. 8(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 62(b) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F44 Article 9 U.K. Fees

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Textual Amendments

F44 Art. 9 omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 63 (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

[F45 Article 9A U.K. Transitional provision in relation to EU exit

1. In this Article, “pre-exit period” means the period beginning with 24 January 2017 and ending immediately before exit day.

2. Where during the pre-exit period—

(a) a manufacturer has submitted an application to the national body of the United Kingdom for the assignment of the unique code of the manufacturer, in accordance with Article 6 as it had effect immediately before exit day; but

(b) the unique code of the manufacturer has not been assigned,

3. Where during the pre-exit period the national body of the United Kingdom has assigned the unique code for a manufacturer, in accordance with Article 4 as it had effect immediately before IP completion day, that unique code is to be treated as if it were issued by the UK national body (or, if none is designated, the Secretary of State) in accordance with Article 4 as it has effect on and after IP completion day.]

Textual Amendments

F45 Art. 9A inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 64 (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2019/1246, regs. 1(3), 16(b) (as amended by S.I. 2020/852, regs. 2(1), 5, Sch. 2 para. 1(b))); 2020 c. 1, Sch. 5 para. 1(1)

F46 CHAPTER 4 U.K. FINAL PROVISIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Textual Amendments

F46 Ch. 4 omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 65 (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F47 ...

F48 ...

F49 ...

Textual Amendments

F47 Words in Signature omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 66(a) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F48 Words in Signature omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 66(b) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F49 Words in Signature omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 66(c) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)