Search Legislation

Advanced Search

Commission Regulation (EU) 2018/1832Show full title

Commission Regulation (EU) 2018/1832 of 5 November 2018 amending Directive 2007/46/EC of the European Parliament and of the Council, Commission Regulation (EC) No 692/2008 and Commission Regulation (EU) 2017/1151 for the purpose of improving the emission type approval tests and procedures for light passenger and commercial vehicles, including those for in-service conformity and real-driving emissions and introducing devices for monitoring the consumption of fuel and electric energy (Text with EEA relevance)

Help about what version

What Version

Help about advanced features

Advanced Features

Help about UK-EU Regulation

Legislation originating from the EU

When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.

Close

This item of legislation originated from the EU

Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).

Changes to legislation:

This version of this Regulation was derived from EUR-Lex on IP completion day (31 December 2020 11:00 p.m.). It has not been amended by the UK since then. Find out more about legislation originating from the EU as published on legislation.gov.uk. Help about Changes to Legislation

Close

Changes to Legislation

Revised legislation carried on this site may not be fully up to date. At the current time any known changes or effects made by subsequent legislation have been applied to the text of the legislation you are viewing by the editorial team. Please see ‘Frequently Asked Questions’ for details regarding the timescales for which new effects are identified and recorded on this site.

ANNEX XIU.K.

Annexes I, III, VIII and IX to Directive 2007/46/EC are amended as follows:

(1)

Annex I is amended as follows:

(a)

the following points 0.2.2.1. to 0.2.3.9. are inserted:

‘0.2.2.1.Allowed Parameter Values for multistage type approval to use the base vehicle emission values (insert range if applicable) (y):

Final Vehicle mass in running order (in kg): …

Frontal area for final vehicle (in cm2): …

Rolling resistance (kg/t): …

Cross-sectional area of air entrance of the front grille (in cm2): …

0.2.3.Identifiers (y):

0.2.3.1.interpolation family's identifier: …

0.2.3.2.ATCT family's identifier: …

0.2.3.3.PEMS family's identifier: …

0.2.3.4.Roadload family's identifier

0.2.3.4.1.Roadload family of VH: …
0.2.3.4.2.Roadload family of VL: …
0.2.3.4.3.Roadload families applicable in the interpolation family: …

0.2.3.5.Roadload Matrix family's identifier: …

0.2.3.6.Periodic regeneration family's identifier: …

0.2.3.7.Evaporative test family's identifier: …

0.2.3.8.OBD family's identifier: …

0.2.3.9.other family's identifier: …’;

(b)

the following point 2.6.3. is inserted:

‘2.6.3.Rotational mass (y): 3 % of the sum of mass in running order and 25 kg or value, per axle (kg): …’;

(c)

point 3.2.2.1. is replaced by the following:

‘3.2.2.1.Diesel/Petrol/LPG/NG or Biomethane/Ethanol (E 85)/Biodiesel/Hydrogen (1) (6)’;

(d)

the following point 3.2.12.0. is inserted:

‘3.2.12.0.Emission character of type approval (y)’;

(e)

point 3.2.12.2.5.5. is replaced by the following:

‘3.2.12.2.5.5.Schematic drawing of the fuel tank (petrol and ethanol engines only): …’;

(f)

after point 3.2.12.2.5.5. the following points are inserted:

‘3.2.12.2.5.5.1.Fuel tank system capacity, material and construction: …

3.2.12.2.5.5.2.Description of vapour hose material, fuel line material and connection technique of the fuel system: …

3.2.12.2.5.5.3.Sealed tank system: yes/no

3.2.12.2.5.5.4.Description of fuel tank relief valve setting (air ingestion and relief): …

3.2.12.2.5.5.5.Description of the purge control system: …’;

(g)

the following point 3.2.12.2.5.7. is inserted:

‘3.2.12.2.5.7.Permeability factor: …’;

(h)

the following point 3.2.12.2.5.12. is inserted:

‘3.2.12.2.12.Water injection: yes/no (1)’;

(i)

point 3.2.19.4.1. is deleted;

(j)

point 3.2.20. is replaced by the following:

‘3.2.20.Heat storage information (y)’;

(k)

point 3.2.20.1. is replaced by the following:

‘3.2.20.1.Active heat storage device: yes/no (1)’;

(l)

point 3.2.20.2. is replaced by the following:

‘3.2.20.2.Insulation materials: yes/no (1)’;

(m)

the following points 3.2.20.2.5. to 3.2.20.2.6. are inserted:

‘3.2.20.2.5.Worst case approach vehicle cool down: yes/no (1)

3.2.20.2.5.1.(not worst case approach) Minimum soaking time, tsoak_ATCT (hours): …

3.2.20.2.5.2.(not worst case approach) Location of the engine temperature measurement: …

3.2.20.2.6.Single interpolation family within the ATCT family approach: yes/no (1)’;

(n)

points 3.5.7.1. and 3.5.7.1.1. are replaced by the following:

‘3.5.7.1.Test vehicle parameters (y)

a

Representative vehicle is tested for the road load matrix family.

VehicleVehicle Low (VL)if existingVehicle High (VH)VMif existingV representative (only for road load matrix family)aDefault values
Vehicle bodywork type (variant/version)—
Road load method used (measurement or calculation by road load family)——
Road load information:
Tyres make and type, if measurement—
Tyre dimensions (front/rear), if measurement—
Tyre rolling resistance (front/rear) (kg/t)
Tyre pressure (front/rear) (kPa), if measurement
Delta CD × A of vehicle L compared to vehicle H (IP_H minus IP_L)———
Delta CD × A compared to road load family vehicle L (IP_H/L minus RL_L), if calculation by road load family——
Vehicle test mass (kg)
Road load coefficients
f0 (N)
f1 (N/(km/h))
f2 (N/(km/h)2)
Frontal area m2 (0,000 m2)———
Cycle Energy Demand (J)

3.5.7.1.1.Fuel used for the Type 1 test and selected for the measurement of the net power in accordance with Annex XX to this Regulation (for LPG or NG vehicles only): …’;

(o)

points 3.5.7.1.1.1. to 3.5.7.1.3.2.3. are deleted;

(p)

point 3.5.7.2.1. to 3.5.7.2.1.2.0. are replaced by the following:

‘3.5.7.2.1.CO2 mass emission for pure ICE vehicles and NOVC-HEVs

3.5.7.2.1.0.Minimum and maximum CO2 values within the interpolation family

3.5.7.2.1.1.Vehicle high: … g/km

3.5.7.2.1.1.0.Vehicle high (NEDC): … g/km

3.5.7.2.1.2.Vehicle low (if applicable): … g/km

3.5.7.2.1.2.0.Vehicle low (if applicable) (NEDC): … g/km

3.5.7.2.1.3.Vehicle M (if applicable): … g/km

3.5.7.2.1.3.0.Vehicle M (if applicable) (NEDC): … g/km’;
(r)

points 3.5.7.2.2. to 3.5.7.2.2.3.0. are replaced by the following:

‘3.5.7.2.2.Charge-Sustaining CO2 mass emission for OVC-HEVs

3.5.7.2.2.1.Charge Sustaining CO2 mass emission vehicle high: g/km

3.5.7.2.2.1.0.Combined CO2 mass emission vehicle high (NEDC Condition B): g/km

3.5.7.2.2.2.Charge Sustaining CO2 mass emission vehicle low (if applicable): g/km

3.5.7.2.2.2.0.Combined CO2 mass emission vehicle low (if applicable) (NEDC Condition B): g/km

3.5.7.2.2.3.Charge Sustaining CO2 mass emission vehicle M (if applicable): g/km

3.5.7.2.2.3.0.Combined CO2 mass emission vehicle M (if applicable) (NEDC Condition B): g/km’;
(s)

points 3.5.7.2.3. to 3.5.7.2.3.3.0. are replaced with the following:

‘3.5.7.2.3.Charge Depleting CO2 mass emission and weighted CO2 mass emission for OVC-HEVs

3.5.7.2.3.1.Charge Depleting CO2 mass emission of Vehicle high: … g/km

3.5.7.2.3.1.0.Charge Depleting CO2 mass emission of Vehicle high (NEDC Condition A): … g/km

3.5.7.2.3.2.Charge Depleting CO2 mass emission of Vehicle low (if applicable): … g/km

3.5.7.2.3.2.0.Charge Depleting CO2 mass emission of Vehicle low (if applicable) (NEDC Condition A): … g/km

3.5.7.2.3.3.Charge Depleting CO2 mass emission of Vehicle M (if applicable): … g/km

3.5.7.2.3.3.0.Charge Depleting CO2 mass emission of Vehicle M (if applicable) (NEDC Condition A): … g/km’;
(s)

the following point 3.5.7.2.3.4. is added:

‘3.5.7.2.3.4.Minimum and maximum weighted CO2 values within the OVC interpolation family’;

(t)

point 3.5.7.4.3. is deleted;

(u)

Point 3.5.8.3. and table are replaced by the following:

‘3.5.8.3.Emissions data related to the use of eco-innovations (repeat the table for each reference fuel tested) (w1)

Total NEDC CO2 emissions saving (g/km) (w5)

Total WLTP CO2 emissions saving (g/km) (w5)’

Decision approving the eco-innovation (w2)Code of the eco-innovation (w3)1. CO2 emissions of the baseline vehicle (g/km)2. CO2 emissions of the eco-innovation vehicle (g/km)3. CO2 emissions of the baseline vehicle under type 1 test-cycle (w4)4. CO2 emissions of the eco-innovation vehicle under type 1 test-cycle5. Usage factor (UF), i.e. temporal share of technology usage in normal operation conditionsCO2 emissions savings ((1 – 2) – (3 – 4)) * 5
xxxx/201x
(v)

the following point 3.8.5. is inserted:

‘3.8.5.Lubricant specification: … W …’;

(w)

points 4.5.1.1. to 4.5.1.3. are deleted;

(x)

in point 4.6., at the bottom of the first column of the table, the word ‘Reverse’ is deleted;

(y)

the following points 4.6.1. to 4.6.1.7.1. are inserted:

‘4.6.1.Gearshift (y)

4.6.1.1.Gear 1 excluded: yes/no (1)

4.6.1.2.n_95_high for each gear: … min– 1

4.6.1.3.nmin_drive

4.6.1.3.1.1st gear: … min– 1
4.6.1.3.2.1st gear to 2nd:… min– 1
4.6.1.3.3.2nd gear to standstill: … min– 1
4.6.1.3.4.2nd gear: … min– 1
4.6.1.3.5.3rd gear and beyond: … min– 1

4.6.1.4.n_min_drive_set for acceleration/constant speed phases (n_min_drive_up): … min– 1

4.6.1.5.n_min_drive_set for deceleration phases (nmin_drive_down):

4.6.1.6.initial period of time

4.6.1.6.1.t_start_phase: … s
4.6.1.6.2.n_min_drive_start: … min– 1
4.6.1.6.3.n_min_drive_up_start: … min– 1

4.6.1.7.use of ASM: yes/no (1)

4.6.1.7.1.ASM values: …’;
(z)

the following point 4.12. is added:

‘4.12.Gearbox lubricant: … W …’;

(aa)

the following points 12.8. to 12.8.3.2. are inserted:

‘12.8.Devices or systems with driver selectable modes which influence CO2 emissions and/or criteria emissions and do not have a predominant mode: yes/no (1)

12.8.1.Charge sustaining test (if applicable) (state for each device or system)

12.8.1.1.Best case mode: …
12.8.1.2.Worst case mode: …

12.8.2.Charge depleting test (if applicable) (state for each device or system)

12.8.2.1.Best case mode: …
12.8.2.2.Worst case mode: …

12.8.3.Type 1 test (if applicable) (state for each device or system)

12.8.3.1.Best case mode: …
12.8.3.2.Worst case mode: …’;
(ab)

in the Explanatory notes, the following footnote (y) is added:

‘(y)Only for the approval under Regulation (EC) No 715/2007 and its amendments.’;

(2)

Annex III is amended as follows:

(a)

the following point 0.2.2.1. is inserted:

‘0.2.2.1.Allowed Parameter Values for multistage type approval to use the base vehicle emission values (insert range if applicable) (y):

Final Vehicle mass (in kg): …

Frontal area for final vehicle (in cm2): …

Rolling resistance (kg/t): …

Cross-sectional area of air entrance of the front grille (in cm2): …’;

(b)

point 3.2.2.1. is replaced by the following:

‘3.2.2.1.Diesel/Petrol/LPG/NG or Biomethane/Ethanol (E 85)/Biodiesel/Hydrogen (1) (6)’;

(c)

the following point 3.2.12.2.8.2.2. is inserted:

‘3.2.12.2.8.2.2.Activation of the creep mode ‘disable after restart’/‘disable after fuelling‘/‘disable after parking’ (7)’;

(d)

point 3.2.12.8.8.1. is replaced by the following:

‘3.2.12.2.8.8.1.List of components on-board the vehicle of the systems ensuring the correct operation of NOx control measures’;

(3)

Annex VIII is amended as follows:

(a)

in point 2.1.1. the line:

‘Number of particles (PN) (#/km) (1)’

is replaced by the following:

‘Number of particles (PN) (#/km) (if applicable)’

(b)

in point 2.1.5. the line:

‘Number of particles (PN) (1)’

is replaced by the following:

‘Number of particles (PN) (if applicable)’

(c)

in point 3.1., in the third table, the last seven rows are replaced by the following:

‘f0 (N)………
f1 (N/(km/h))………
f2 (N/(km/h)2)………
RR (kg/t)………
Delta Cd * A (for VL if applicable compared to VH) (m2)………
Test Mass (kg)………
Frontal area (m2) (for road load matrix family vehicles only)’
(d)

in point 3.2., in the third table, the last seven rows are replaced by the following:

‘f0 (N)……
f1 (N/(km/h))……
f2 (N/(km/h)2)……
RR (kg/t)……
Delta CD × A (for VL or VM compared to VH) (m2)……
Test Mass (kg)……
Frontal area (m2) (for road load matrix family vehicles only)’
(e)

in point 3.3., in the third table, the last seven rows are replaced by the following:

‘f0 (N)……
f1 (N/(km/h))……
f2 (N/(km/h)2)……
RR (kg/t)……
Delta CD × A (for VL compared to VH) (m2)……
Test Mass (kg)……
Frontal area (m2) (for road load matrix family vehicles only)’
(f)

in point 3.4. the second table is replaced by the following:

‘Variant/Version:Variant/Version:
Fuel Consumption (Combined) (kg/100 km)……
f0 (N)……
f1 (N/(km/h))……
f2 (N/(km/h)2)……
RR (kg/t)……
Test Mass (kg)…’
(g)

the title of point 3.5. is replaced by the following:

‘Output report(s) from the correlation tool in accordance with Regulation (EU) 2017/1152 and/or 2017/1153 and final NEDC values’

(h)

the following points 3.5.3. and 3.5.4. are inserted:

‘3.5.3.Internal combustion engines, including not externally chargeable hybrid electric vehicles (NOVC) (1) (2)

Final correlated NEDC valuesInterpolation family identifier
VHVL (if applicable)
CO2 mass emission (urban conditions) (g/km)
CO2 mass emission (extra-urban conditions) (g/km)
CO2 mass emission (combined) (g/km)
Fuel consumption (urban conditions) (l/100 km) (1)
Fuel consumption (extra-urban conditions) (l/100 km) (1)
Fuel consumption (combined) (l/100 km) (1)

3.5.4. Externally chargeable hybrid electric vehicles (OVC) (1)

Final correlated NEDC valuesInterpolation family identifier
VHVL (if applicable)
CO2 mass emission (weighted, combined) (g/km)……
Fuel consumption (weighted, combined) (l/100 km) (g)……’
(4)

Annex IX is amended as follows:

(a)

Part I is amended as follows:

(i)

in model A1 – side 1 of the certificate of conformity for complete vehicles, the following new points are inserted:

‘0.2.3.Identifiers (if applicable) (r):

0.2.3.1.interpolation family's identifier: …

0.2.3.2.ATCT family's identifier: …

0.2.3.3.PEMS family's identifier: …

0.2.3.4.Roadload family's identifier: …

0.2.3.5.Roadload Matrix family's identifier (if applicable): …

0.2.3.6.Periodic regeneration family's identifier: …

0.2.3.7.Evaporative test family's identifier: …’;

(ii)

in model A2 – side 1 of the certificate of conformity for complete vehicles type-approved in small series, the following points are inserted:

‘0.2.3.Identifiers (if applicable) (r):

0.2.3.1.interpolation family's identifier: …

0.2.3.2.ATCT family's identifier: …

0.2.3.3.PEMS family's identifier: …

0.2.3.4.Roadload family's identifier: …

0.2.3.5.Roadload Matrix family's identifier (if applicable): …

0.2.3.6.Periodic regeneration family's identifier: …

0.2.3.7.Evaporative test family's identifier: …’;

(iii)

in model B – side 1 of the certificate of conformity for completed vehicles, the following new points are inserted:

‘0.2.3.Identifiers (if applicable) (r):

0.2.3.1.interpolation family's identifier: …

0.2.3.2.ATCT family's identifier: …

0.2.3.3.PEMS family's identifier: …

0.2.3.4.Roadload family's identifier: …

0.2.3.5.Roadload Matrix family's identifier (if applicable): …

0.2.3.6.Periodic regeneration family's identifier: …

0.2.3.7.Evaporative test family's identifier: …’;

(iv)

Side 2 of the certificate of conformity for category M1 vehicles (complete and completed vehicles) is amended as follows:

  • the following points 28 to 28.1.2. are inserted:

    ‘28.Gearbox (type): …

    28.1.Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…
    28.1.1.Final drive ratio (if applicable): …
    28.1.2.Final drive ratios (to complete if and where applicable)
    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…’

  • point 35. is replaced by the following:

    ‘35.Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;

  • point 47.1. is replaced by the following:

    ‘47.1.Parameters for emission testing of Vind (r)’;

  • point 47.1.2. is replaced by the following:

    ‘47.1.2.Frontal area, m2 (t): …’;

  • the following new point 47.1.2.1 is inserted:

    ‘47.1.2.1.Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;

  • the following points 47.2. to 47.2.3. are inserted:

    ‘47.2.Driving cycle (r)

    47.2.1.Driving Cycle class: 1/2/3a/3b

    47.2.2.Downscaling factor (fdsc): …

    47.2.3.Capped speed: yes/no’;

  • in point 49. in sub-point 1., the legend of the table is replaced by the following:

    ‘NEDC valuesCO2 emissionsFuel consumption’
(v)

Side 2 of the certificate of conformity for category M2 vehicles (complete and completed vehicles) is amended as follows:

  • the following points 28.1, 28.1.1. and 28.1.2. are inserted:

    ‘28.1.Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…

    28.1.1.Final drive ratio (if applicable): …

    28.1.2.Final drive ratios (to complete if and where applicable)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…’

  • point 35. is replaced by the following:

    ‘35.Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;

  • point 47.1. is replaced by the following:

    ‘47.1.Parameters for emission testing of Vind (r)’;

  • point 47.1.2. is replaced by the following:

    ‘47.1.2.Frontal area, m2 (t): …’;

  • the following point 47.1.2.1 is inserted:

    ‘47.1.2.1.Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;

  • (vi) the following points 47.2. to 47.2.3. are inserted:

    ‘47.2.Driving cycle (r)

    47.2.1.Driving Cycle class: 1/2/3a/3b

    47.2.2.Downscaling factor (fdsc): …

    47.2.3.Capped speed: yes/no’;

  • in point 49., in sub-point 1, the legend of the table is replaced by the following:

    ‘NEDC valuesCO2 emissionsFuel consumption’
(vi)

Side 2 of the certificate of conformity for category N1 vehicles (complete and completed vehicles) is amended as follows:

  • the following points 28.1., 28.1.1. and 28.1.2. are inserted:

    ‘28.1.Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…

    28.1.1.Final drive ratio (if applicable): …

    28.1.2.Final drive ratios (to complete if and where applicable)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…’

  • point 35 is replaced by the following:

    ‘35.Fitted tyre/wheel combination/ energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;

  • point 47.1. is replaced by the following:

    ‘47.1.Parameters for emission testing of Vind (r)’;

  • point 47.1.2. is replaced by the following:

    ‘47.1.2.Frontal area, m2 (t): …’;

  • the following point 47.1.2.1 is inserted:

    ‘47.1.2.1.Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;

  • the following points 47.2. to 47.2.3. are inserted:

    ‘47.2.Driving cycle (r)

    47.2.1.Driving Cycle class: 1/2/3a/3b

    47.2.2.Downscaling factor (fdsc): …

    47.2.3.Capped speed: yes/no’;

  • in point 49, in sub-point 1, the legend of the table is replaced by the following:

    ‘NEDC valuesCO2 emissionsFuel consumption’

  • in point 49, in sub-point 1, in the table, the following row is added:

    ‘Verification factor (if applicable)‘1’ or ‘0’’
(vii)

Side 2 of the certificate of conformity for category N2 vehicles (complete and completed vehicles) is amended as follows:

  • point 7. is replaced by the following:

    ‘7.Height (r): … mm’

  • the following points 28.1, 28.1.1. and 28.1.2. are inserted:

    ‘28.1.Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…

    28.1.1.Final drive ratio (if applicable): …

    28.1.2.Final drive ratios (to complete if and where applicable)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…’

  • point 35. is replaced by the following:

    ‘35.Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;

  • point 47.1. is replaced by the following:

    ‘47.1.Parameters for emission testing of Vind (r)’;

  • point 47.1.2. is replaced by the following:

    ‘47.1.2.Frontal area, m2 (t): …’;

  • the following point 47.1.2.1 is inserted:

    ‘47.1.2.1.Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;

  • the following points 47.2. to 47.2.3. are inserted:

    ‘47.2.Driving cycle (r)

    47.2.1.Driving Cycle class: 1/2/3a/3b

    47.2.2.Downscaling factor (fdsc): …

    47.2.3.Capped speed: yes/no’;

  • in point 49, in sub-point 1, the legend of the table is replaced by the following:

    ‘NEDC valuesCO2 emissionsFuel consumption’

  • in point 49, in sub-point 1, in the table, the following row is added:

    ‘Verification factor (if applicable)‘1’ or ‘0’’
(viii)

Side 2 of the certificate of conformity for category N3 vehicles (complete and completed vehicles) is amended as follows:

  • point 7. is deleted.

(b)

Part II is amended as follows:

(i)

in model C1 – side 1 of the certificate of conformity for incomplete vehicles, the following points 0.2.3. to 0.2.3.7. are inserted:

‘0.2.3.Identifiers (if applicable) (r):

0.2.3.1.interpolation family's identifier: …

0.2.3.2.ATCT family's identifier: …

0.2.3.3.PEMS family's identifier: …

0.2.3.4.Roadload family's identifier: …

0.2.3.5.Roadload Matrix family's identifier (if applicable): …

0.2.3.6.Periodic regeneration family's identifier: …

0.2.3.7.Evaporative test family's identifier: …’;

(ii)

in model C2 – side 1 of the certificate of conformity for incomplete vehicles type-approved in small series the following points 0.2.3. to 0.2.3.7. are inserted:

‘0.2.3.Identifiers (if applicable) (r):

0.2.3.1.interpolation family's identifier: …

0.2.3.2.ATCT family's identifier: …

0.2.3.3.PEMS family's identifier: …

0.2.3.4.Roadload family's identifier:…

0.2.3.5.Roadload Matrix family's identifier (if applicable): …

0.2.3.6.Periodic regeneration family's identifier: …

0.2.3.7.Evaporative test family's identifier: …’;

(iii)

Side 2 of the certificate of conformity for category M1 vehicles (incomplete vehicles) is amended as follows:

  • the following points 28 to 28.1.2. are inserted:

    ‘28.Gearbox (type): …

    28.1.Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…
    28.1.1.Final drive ratio (if applicable): …
    28.1.2.Final drive ratios (to complete if and where applicable)
    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…’

  • point 35. is replaced by the following:

    ‘35.Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;

  • point 47.1. is replaced by the following:

    ‘47.1.Parameters for emission testing of Vind (r)’;

  • point 47.1.2. is replaced by the following:

    ‘47.1.2.Frontal area, m2 (t): …’;

  • the following new point 47.1.2.1 is inserted:

    ‘47.1.2.1.Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;

  • (vi) the following points 47.2. to 47.2.3. are inserted:

    ‘47.2.Driving cycle (r)

    47.2.1.Driving Cycle class: 1/2/3a/3b

    47.2.2.Downscaling factor (fdsc): …

    47.2.3.Capped speed: yes/no’;

(iv)

Side 2 of the certificate of conformity for category M2 vehicles (incomplete vehicles) is amended as follows:

  • the following points 28.1 to 28.1.2. are inserted:

    ‘28.1.Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…

    28.1.1.Final drive ratio (if applicable): …

    28.1.2.Final drive ratios (to complete if and where applicable)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…’

  • point 35. is replaced by the following:

    ‘35.Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;

  • point 47.1. is replaced by the following:

    ‘47.1.Parameters for emission testing of Vind (r)’;

  • point 47.1.2. is replaced by the following:

    ‘47.1.2.Frontal area, m2 (t): …’;

  • the following point 47.1.2.1 is inserted:

    ‘47.1.2.1.Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;

  • the following points 47.2. to 47.2.3. are inserted:

    ‘47.2.Driving cycle (r)

    47.2.1.Driving Cycle class: 1/2/3a/3b

    47.2.2.Downscaling factor (fdsc): …

    47.2.3.Capped speed: yes/no’;

(v)

Side 2 of the certificate of conformity for N1 category vehicles (incomplete vehicles) is amended as follows:

  • the following points 28.1, 28.1.1. and 28.1.2. are inserted:

    ‘28.1.Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…

    28.1.1.Final drive ratio (if applicable): …

    28.1.2.Final drive ratios (to complete if and where applicable)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…’

  • point 35. is replaced by the following:

    ‘35.Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;

  • point 47.1. is replaced by the following:

    ‘47.1.Parameters for emission testing of Vind (r)’;

  • point 47.1.2. is replaced by the following:

    ‘47.1.2.Frontal area, m2 (t): …’;

  • the following point 47.1.2.1 is inserted:

    ‘47.1.2.1.Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;

  • the following points 47.2. to 47.2.3. are inserted:

    ‘47.2.Driving cycle (r)

    47.2.1.Driving Cycle class: 1/2/3a/3b

    47.2.2.Downscaling factor (fdsc): …

    47.2.3.Capped speed: yes/no’;

(vi)

Side 2 of the certificate of conformity for N2 category vehicles (incomplete vehicles) is amended as follows:

  • the following new points 28.1, 28.1.1. and 28.1.2. are inserted:

    ‘28.1.Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…

    28.1.1.Final drive ratio (if applicable): …

    28.1.2.Final drive ratios (to complete if and where applicable)

    1st gear2nd gear3rd gear4th gear5th gear6th gear7th gear8th gear…’

  • point 35. is replaced by the following:

    ‘35.Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;

  • point 47.1. is replaced by the following:

    ‘47.1.Parameters for emission testing of Vind (r)’;

  • point 47.1.2. is replaced by the following:

    ‘47.1.2.Frontal area, m2 (t): …’;

  • the following point 47.1.2.1 is inserted:

    ‘47.1.2.1.Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;

  • the following points 47.2. to 47.2.3. are inserted:

    ‘47.2.Driving cycle (r)

    47.2.1.Driving Cycle class: 1/2/3a/3b

    47.2.2.Downscaling factor (fdsc): …

    47.2.3.Capped speed: yes/no’;

(c)

The Explanatory notes relating to Annex IX are amended as follows:

(i)

the explanatory note (h) is replaced by the following:

‘(h)Optional equipment and additional tyre/wheel combinations under this letter can be added under entry ‘Remarks’. If a vehicle is supplied with a complete set of standard wheels and tyres and a complete set of snow tyres (marked with a 3 peaked mountain and snowflake symbol – 3PMS) with or without wheels, the snow tyres and their wheels where applicable shall be considered as additional tyre/wheel combinations irrespective of the wheels/tyres actually fitted to the vehicle.’;

(ii)

the following explanatory note is added:

‘(t)only applicable to individual vehicles from roadload matrix family (RLMF)’;

(5)

Annex XI is amended as follows:

In the Meaning of notes, note (1) is replaced by the following:

‘(1)For vehicles with a reference mass not exceeding 2 610 kg. At the manufacturer's request, may apply to vehicles with a reference mass not exceeding 2 840 kg or if the vehicles is a special purpose vehicle with the code SB relating to armoured vehicles also with a reference mass exceeding 2 840 kg. With regard to Access to information, for other parts (e.g. living compartment) than the base vehicle, it is sufficient that the manufacturer provides access to repair and maintenance information in a readily accessible and prompt manner.’.

Back to top

Options/Help

Print Options

You have chosen to open the Whole Regulation

The Whole Regulation you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.

Would you like to continue?

You have chosen to open Schedules only

The Schedules you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.

Would you like to continue?

Close

Legislation is available in different versions:

Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.

Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.

Close

See additional information alongside the content

Geographical Extent: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.

Show Timeline of Changes: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.

Close

Opening Options

Different options to open legislation in order to view more content on screen at once

Close

More Resources

Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:

  • the original print PDF of the as adopted version that was used for the EU Official Journal
  • lists of changes made by and/or affecting this legislation item
  • all formats of all associated documents
  • correction slips
  • links to related legislation and further information resources
Close

Timeline of Changes

This timeline shows the different versions taken from EUR-Lex before exit day and during the implementation period as well as any subsequent versions created after the implementation period as a result of changes made by UK legislation.

The dates for the EU versions are taken from the document dates on EUR-Lex and may not always coincide with when the changes came into force for the document.

For any versions created after the implementation period as a result of changes made by UK legislation the date will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. For further information see our guide to revised legislation on Understanding Legislation.

Close

More Resources

Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:

  • the original print PDF of the as adopted version that was used for the print copy
  • correction slips

Click 'View More' or select 'More Resources' tab for additional information including:

  • lists of changes made by and/or affecting this legislation item
  • confers power and blanket amendment details
  • all formats of all associated documents
  • links to related legislation and further information resources

The data on this page is available in the alternative data formats listed: