- Latest available (Revised)
- Original (As adopted by EU)
Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, amending Regulations (EC) No 715/2007 and (EC) No 595/2009 and repealing Directive 2007/46/EC (Text with EEA relevance)
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).
Regulation (EU) 2018/858 of the European Parliament and of the Council, PART A is up to date with all changes known to be in force on or before 26 August 2024. There are changes that may be brought into force at a future date. Changes that have been made appear in the content and are referenced with annotations.
Revised legislation carried on this site may not be fully up to date. Changes and effects are recorded by our editorial team in lists which can be found in the ‘Changes to Legislation’ area. Where those effects have yet to be applied to the text of the legislation by the editorial team they are also listed alongside the legislation in the affected provisions. Use the ‘more’ link to open the changes and effects relevant to the provision you are viewing.
[F1For the purposes of GB type-approval, including GB small series type-approval, and individual vehicle approval], vehicles shall be categorised in accordance with the classification referred to in Article 4.
Textual Amendments
F1Words in Annex 1 Pt. A point 1 substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 40(3)(a)
Approval can only be granted for the categories referred to in Article 4(1).
‘Off-road vehicle (ORV)’ means a vehicle that belongs to category M or N, having specific technical features which permit its use off the normal roads.
For those categories of vehicles, the letter ‘G’ shall be added as suffix to the letter and numeral identifying the vehicle category.
The criteria for the subcategorisation of vehicles as ORV are specified in point 4 of this Part.
The various types of special purpose vehicles are defined and listed in point 5.
For those categories of vehicles, the letter ‘G’ shall be added as suffix to the letter and numeral identifying the vehicle category.
Moreover, for incomplete vehicles that are intended to fall into the SPV subcategory, the letter ‘S’ shall be added as second suffix.
6 in the case of N1 vehicles;
8 in the case of N2 or N3 vehicles.
when N = 0:
P – M ≥ 100 kg
when 0 < N ≤ 2:
P – (M + N × 68) ≥ 150 kg;
when N > 2:
P – (M + N × 68) ≥ N × 68;
where the letters have the following meaning:
‘P’ is the technically permissible maximum laden mass;
‘M’ is the mass in running order;
‘N’ is the number of seating positions excluding the driver's seating position.
When one or more of the criteria are not met, the vehicle shall be categorised as M1.
the loading of the goods shall be possible by a rear door, a tailgate or a side-door designed and constructed for that purposes;
in the case of a rear door or a tailgate, the loading aperture shall meet the following requirements:
in the case the vehicle is fitted with only one row of seats or with only the driver seat, the minimum height of the loading aperture shall be at least 600 mm;
in the case the vehicle is fitted with two or more rows of seats, the minimum height of the loading aperture shall be at least 800 mm and the aperture shall show a surface of at least 12 800 cm2;
The cargo area shall meet the following requirements:
‘cargo area’ means the part of the vehicle located behind the row(s) of seats or behind the driver seat when the vehicle is fitted with only one driver seat;
the loading surface of the cargo area shall be generally flat;
where the vehicle is fitted with only one row of seats or with one seat, the minimum length of the cargo area shall be at least 40 % of the wheelbase;
where the vehicle is fitted with two or more rows of seats, the minimum length of the cargo area shall be at least 30 % of the wheelbase.
Where the seats of the last row of seats can be easily removed from the vehicle without the use of special tools, the requirements regarding the length of the cargo area shall be met with all the seats installed in the vehicle;
the requirements regarding the length of the cargo area shall be met when the seats of the first row or of the last row, as the case may be, are upright in their normal position for use by the vehicle occupants.
‘Height of the loading aperture’, means the vertical distance between two horizontal planes tangent respectively to the highest point of the lower part of the doorway and the lowest point of the upper part of the doorway;
‘Surface of the loading aperture’ means the greatest surface of the orthogonal projection on a vertical plane, perpendicular to the centreline of the vehicle, of the maximum aperture permitted when the rear door(s) or tailgate is (are) wide open;
‘Wheelbase’, for the purposes of application of the formulae in points 3.8.2.2 and 3.8.3.1, means the distance between:
the centreline of the front axle and the centreline of the second axle in the case of a two axle vehicle; or
the centreline of the front axle and the centreline of a virtual axle equally distant from the second and third axle in the case of a three axle vehicle.
The seats shall be adjusted at their rear outermost positions;
The seat back, if adjustable, shall be adjusted as to accommodate the three-dimensional H-point machine at a torso angle of 25 degrees;
The seat back, if not adjustable, shall be in the position designed by the vehicle manufacturer;
When the seat is adjustable in height, it shall be adjusted to its lowest position.
The vehicle shall be in loaded conditions corresponding to its maximum mass;
The vehicle shall be with its wheels straight ahead.
When the vehicle is not fitted with a partition or a wall, the length shall be measured from a vertical plane tangent to the rear outermost point of the top of the seat back to the rear internal pane or door or tailgate, in closed position;
When the vehicle is fitted with a partition or a wall, the length shall be measured from a vertical plane tangent to the rear outermost point of the partition or the wall to the rear internal pane or door or tailgate, as the case may be, in closed position;
The requirements concerning the length shall be fulfilled at least along a horizontal line situated in the longitudinal vertical plane passing through the centreline of the vehicle, at the level of the load floor.
the loading of the goods shall be possible by a rear door, a tailgate or a panel or other means;
the minimum height of the loading aperture shall be at least 800 mm and the aperture shall show a surface of at least 12 800 cm2;
The minimum length of the cargo area shall be at least 40 % of the wheelbase.
at least one front and at least one rear axle designed to be driven simultaneously irrespective of whether one powered axle can be disengaged;
at least one differential locking mechanism or a mechanism having similar effect is fitted;
they are able to climb at least a 25 % gradient as a solo vehicle;
they satisfy five out of the following six requirements:
the approach angle shall be at least 25 degrees;
the departure angle shall be at least 20 degrees;
the ramp angle shall be at least 20 degrees;
the ground clearance under the front axle shall be at least 180 mm;
the ground clearance under the rear axle shall be at least 180 mm;
the ground clearance between the axles shall be at least 200 mm.
all their axles are driven simultaneously, irrespective of whether one or more powered axles can be disengaged;
at least one front and at least one rear axle are designed to be driven simultaneously irrespective of whether one powered axle can be disengaged;
at least one differential locking mechanism or a mechanism having the same effect is fitted;
they are able to climb a 25 % gradient as a solo vehicle;
they satisfy at least five out of the following six requirements if their maximum mass does not exceed 7,5 tonnes and at least four if their maximum mass exceeds 7,5 tonnes:
the approach angle shall be at least 25 degrees;
the departure angle shall be at least 25 degrees;
the ramp angle shall be at least 25 degrees;
the ground clearance under the front axle shall be at least 250 mm;
the ground clearance between axles shall be at least 300 mm;
the ground clearance under the rear axle shall be at least 250 mm.
all their axles are driven simultaneously, irrespective of whether one or more powered axles can be disengaged;
at least half of the axles (or two axles out of the three in the case of a three axle vehicle and three axles in the case of a five axle vehicle) is designed to be driven simultaneously, irrespective of whether one powered axle can be disengaged;
there is at least one differential locking mechanism or a mechanism having similar effect;
they are able to climb a 25 % gradient as solo vehicle;
they satisfy at least four out of the following six requirements:
the approach angle shall be at least 25 degrees;
the departure angle shall be at least 25 degrees;
the ramp angle shall be at least 25 degrees;
the ground clearance under the front axle shall be at least 250 mm;
the ground clearance between axles shall be at least 300 mm;
the ground clearance under the rear axle shall be at least 250 mm.
the transmission of the tractive power to all axles is performed by mechanical means only which provides traction in heavy off-road; or
each of the wheels of the axle in question is driven by an individual hydraulic or electric motor.
If the axles according to the requirements in points 4.1(a), 4.2(a), 4.2(b), 4.3(a), 4.3(b) on simultaneous driven axles are not powered by mechanical means only, the propulsion of the individual wheels shall be designed for heavy off-road operation. In such case it shall be ensured that at least 75 % of total tractive power can be transmitted to the wheel in question when the tractive conditions under the other wheels do not allow to transmit the tractive power properly via these wheels.
The auxiliary drive system according to point 4.5(b) shall not allow to disengage the tractive power automatically until the vehicle reaches 75 % of the maximum vehicle design speed or reaches 65 km/h.
Name | Code | Definition | |
---|---|---|---|
5.1. | Motor caravan | SA | A vehicle of category M with living accommodation space which contains the following equipment as a minimum: (a) seats and table; (b) sleeping accommodation which may be converted from the seats; (c) cooking facilities; (d) storage facilities. This equipment shall be rigidly fixed to the living compartment. However, the table may be designed to be easily removable. |
5.2. | Armoured vehicle | SB | A vehicle intended for the protection of conveyed persons or goods with anti-bullet armour plating. |
5.3. | Ambulance | SC | A vehicle of category M intended for the transport of sick or injured persons and having special equipment for such purpose. |
5.4. | Hearse | SD | A vehicle of category M intended for the transport of deceased persons and having special equipment for such purpose. |
5.5. | Wheelchair accessible vehicle | SH | A vehicle of category M1 constructed or converted specifically so that they accommodate one or more persons seated in their wheelchairs when travelling on the road. |
5.6. | Trailer caravan | SE | A vehicle of category O as defined in term 3.2.1.3 of international standard ISO 3833:1977. |
5.7. | Mobile crane | SF | A vehicle of category N3, not fitted for the carriage of goods, provided with a crane whose lifting moment is equal to or higher than 400 kNm. |
5.8. | Special group | SG | A special purpose vehicle that does not enter in any of the definitions mentioned in this Part. |
5.9. | Converter dolly | SJ | A vehicle of category O equipped with a fifth-wheel coupling to support a semi-trailer with a view to converting the latter into a trailer. |
5.10. | Exceptional load transport trailer | SK | A vehicle of category O4 intended for the transport of indivisible loads that is subject to speed and traffic restrictions because of its dimensions. Under this term are also included hydraulic modular trailers irrespective of the number of modules. |
5.11. | Exceptional load transport motor vehicle | SL | A road tractor or tractor unit for semi-trailer of category N3 meeting all the following conditions: (a) having more than two axles and at least half of the axles (two axles out of three in the case of a three axle vehicle and three axles out of five in the case of a five axle vehicle) designed to be driven simultaneously, irrespective of whether one powered axle can be disengaged; (b) that is designed for towing and pushing exceptional load transport trailer of category O4; (c) that has a minimum engine power of 350 kW; and (d) that can be equipped with an additional front coupling device for heavy towable masses. |
5.12. | Multi-equipment carrier | SM | An off-road vehicle of category N (as defined in point 2.3) designed and constructed for pulling, pushing, carrying and actuating certain inter-changeable equipment: (a) with not less than two mounting areas for this equipment; (b) with standardised, mechanical, hydraulic and/or electrical interfaces (e.g. Power take off) for powering and actuating the inter-changeable equipment; and (c) that fulfils the definition of international standard ISO 3833-1977, paragraph 3.1.4 (special vehicle). If the vehicle is equipped with an auxiliary load platform, its maximum length shall not exceed: (a) 1,4 times of the front or rear track width of the vehicle, whichever is the larger in the case of two axle vehicles; or (b) 2,0 times of the front or rear track width of the vehicle, whichever is the larger in the case of vehicles having more than two axles. |
to converter dolly as defined in point 5.9 of this Part;
to rigid drawbar trailers as defined in point 5.4 of Part C;
to trailers in which persons may be carried when travelling on the road.
Textual Amendments
F2Word in Annex 1 Pt. A point 6.2 omitted (31.12.2022 at 11.00 p.m.) by virtue of The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 40(3)(b)
The Whole Regulation you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.
Would you like to continue?
The Schedules you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.
Would you like to continue?
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Geographical Extent: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Show Timeline of Changes: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
This timeline shows the different versions taken from EUR-Lex before exit day and during the implementation period as well as any subsequent versions created after the implementation period as a result of changes made by UK legislation.
The dates for the EU versions are taken from the document dates on EUR-Lex and may not always coincide with when the changes came into force for the document.
For any versions created after the implementation period as a result of changes made by UK legislation the date will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. For further information see our guide to revised legislation on Understanding Legislation.
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: