ANNEX IRules on data to be monitored and reported
PART A: DATA TO BE MONITORED AND REPORTED BY MEMBER STATES
- (a)
vehicle identification numbers of all new heavy-duty vehicles as referred to in points (a) and (b) of the second paragraph of Article 2 that are registered in the Member State territory;
- (b)
manufacturer name;
- (c)
make (trade name of manufacturer);
- (d)
the code for the bodywork as specified in entry 38 of the certificate of conformity, where available;
- (e)
in the case of the heavy-duty vehicles referred to in point (a) of the second paragraph of Article 2, the information on the powerplant specified in entries 23, 23.1 and 26 of the certificate of conformity.
PART B: DATA TO BE MONITORED AND REPORTED BY MANUFACTURERS OF HEAVY-DUTY VEHICLES
1.Starting years for the monitoring and reporting of data for the heavy-duty vehicle categories set out in points (a) and (b) of the second paragraph of Article 2:
Category of heavy-duty vehicles | Vehicle group in vehicle category (as referred to in Annex I to Regulation (EU) 2017/2400) | Starting yearMonitoring | Starting yearReporting |
---|---|---|---|
N1 | — | — | — |
N2 | 1 and 2 | 2020 | 2021 |
N3 | 3 | 2020 | 2021 |
4, 5, 9 and 10 | 2019 | 2020 | |
11, 12 and 16 | 2020 | 2021 | |
M1 | — | — | — |
M2 | — | — | — |
M3 | — | — | — |
O3 | — | — | — |
O4 | — | — | — |
2.Data to be monitored and reported:
No | Monitoring parameters | Source Part I of Annex IV to Regulation (EU) 2017/2400, unless otherwise specified | Description |
---|---|---|---|
1 | Vehicle identification number (VIN) | 1.1.3 | Vehicle and component identification |
2 | Engine certification number | 1.2.2 | |
3 | CdxA16 certification number (if applicable) | 1.8.3 | |
4 | Transmission certification number | 1.3.2 | |
5 | Axle certification number | 1.6.2 | |
6 | Tyre certification number, axle 1 | 1.9.2 | |
7 | Tyre certification number, axle 2 | 1.9.6 | |
8 | Tyre certification number, axle 3 | 1.9.10 | |
9 | Tyre certification number, axle 4 | 1.9.14 | |
10 | Vehicle category (N1, N2, N3, M1, M2, M3) | 1.1.4 | Vehicle classification |
11 | Axle configuration | 1.1.5 | |
12 | Maximum gross vehicle weight (t) | 1.1.6 | |
13 | Vehicle group | 1.1.7 | |
14 | Name and address of manufacturer | 1.1.1 | Vehicle and chassis specification |
15 | Make (trade name of manufacturer) | 1.1.7 Part II of Annex IV to Regulation (EU) 2017/2400 | |
16 | Corrected actual curb mass (kg) | 1.1.8 | |
17 | Engine rated power (kW) | 1.2.3 | Main engine specifications |
18 | Engine idling speed (1/min) | 1.2.4 | |
19 | Engine rated speed (1/min) | 1.2.5 | |
20 | Engine capacity (ltr) | 1.2.6 | |
21 | Engine reference fuel type (diesel/LPG/CNG…) | 1.2.7 | |
22 | Certification option used for generation of CdxA (standard values/measurement) | 1.8.2 | Aerodynamics |
23 | CdxA value (air drag value) | 1.8.4 | |
24 | Name and address of transmission manufacturer | — | Main transmission specifications |
25 | Make (trade name of transmission manufacturer) | — | |
26 | Certification option used for the generation of simulation tool loss maps (Option 1/Option 2/Option 3/Standard values) | 1.3.3 | |
27 | 1.3.4 | ||
28 | Number of gears | 1.3.5 | |
29 | Transmission ratio final gear | 1.3.6 | |
30 | Retarder type | 1.3.7 | |
31 | Power take off (yes/no) | 1.3.8 | |
32 | Name and address of axle manufacturer | — | Main axle specifications |
33 | Make (trade name of axle manufacturer) | — | |
34 | Certification option used for the generation of a simulation tool loss map (standard values/measurement) | 1.7.3 | |
35 | Axle type (e.g. standard single driven axle) | 1.7.4 | |
36 | Axle ratio | 1.7.5 | |
37 | Certification option used for the generation of a simulation tool loss map (standard values/measurement) | 1.6.3 | Angle drive specifications |
38 | Angle drive ratio | 1.6.4 | |
39 | Name and address of tyre manufacturer | — | Main tyre specifications |
40 | Make (trade name of tyre manufacturer) | — | |
41 | Tyre dimension axle 1 | 1.9.1 | |
42 | Specific rolling resistance coefficient (RRC) of all tyres on axle 1 | 1.9.3 | |
43 | Tyre dimension axle 2 | 1.9.4 | |
44 | Twin axle (yes/no) axle 2 | 1.9.5 | |
45 | Specific RRC of all tyres on axle 2 | 1.9.7 | |
46 | Tyre dimension axle 3 | 1.9.8 | |
47 | Twin axle (yes/no) axle 3 | 1.9.9 | |
48 | Specific RRC of all tyres on axle 3 | 1.9.11 | |
49 | Tyre dimension axle 4 | 1.9.12 | |
50 | Twin axle (yes/no) axle 4 | 1.9.13 | |
51 | Specific RRC of all tyres on axle 4 | 1.9.15 | |
52 | Engine cooling fan technology | 1.10.1 | Main auxiliary specifications |
53 | Steering pump technology | 1.10.2 | |
54 | Electric system technology | 1.10.3 | |
55 | Pneumatic system technology | 1.10.4 | |
56 | Mission profile (long haul, long haul (EMS22), regional, regional (EMS), urban, municipal, construction) | 2.1.1 | Simulation parameters (for each mission profile/load/fuel combination) |
57 | Load (as defined in the simulation tool) (kg) | 2.1.2 | |
58 | Fuel type (diesel/petrol/LPG/CNG/…) | 2.1.3 | |
59 | Total vehicle mass in simulation (kg) | 2.1.4 | |
60 | Average speed (km/h) | 2.2.1 | Vehicle driving performance (for each mission profile/load/fuel combination) |
61 | Minimum instantaneous speed (km/h) | 2.2.2 | |
62 | Maximum instantaneous speed (km/h) | 2.2.3 | |
63 | Maximum deceleration (m/s2) | 2.2.4 | |
64 | Maximum acceleration (m/s2) | 2.2.5 | |
65 | Full load percentage on driving time | 2.2.6 | |
66 | Total number of gear shifts | 2.2.7 | |
67 | Total driven distance (km) | 2.2.8 | |
68 | CO2 emissions (expressed in g/km, g/t-km, g/p-km, g/m3-km) | 2.3.13-2.3.16 | CO2 emissions and fuel consumption (for each mission profile/load/fuel combination) |
69 | Fuel consumption (expressed in g/km, g/t-km, g/p-km, g/m3-km, l/100km, l/t-km, l/p-km, l/m3-km, MJ/km, MJ/t-km, MJ/p-km, MJ/m3-km) | 2.3.1-2.3.12 | |
70 | Simulation tool version (X.X.X.) | 3.1.1 | Software and user information |
71 | Date and time of the simulation | 3.1.2 | |
72 | Number of licence to operate the simulation tool | — | |
73 | Cryptographic hash of simulation tool result | 3.1.4 | |
74 | Advanced CO2 reducing technologies | — | Vehicle CO2 reducing technologies |
75 | CO2 mass emission of the engine over WHTC23 (g/kWh) | Point 1.4.2 of the addendum to Appendix 5, or point 1.4.2 of the addendum to Appendix 7, to Annex I to Regulation (EU) No 582/2011, whichever is applicable | Engine CO2 emission and specific fuel consumption |
76 | Fuel consumption of the engine over WHTC (g/kWh) | Point 1.4.2 of the addendum to Appendix 5, or point 1.4.2 of the addendum to Appendix 7, to Annex I to Regulation (EU) No 582/2011, whichever is applicable | |
77 | CO2 mass emission of the engine over WHSC24 (g/kWh) | Point 1.4.1 of the addendum to Appendix 5, or point 1.4.1 of the addendum to Appendix 7, to Annex I to Regulation (EU) No 582/2011, whichever is applicable | |
78 | Fuel consumption of the engine over WHSC (g/kWh) | Point 1.4.1 of the addendum to Appendix 5, or point 1.4.1 of the addendum to Appendix 7, to Annex I to Regulation (EU) No 582/2011, whichever is applicable | |
Air drag. | |||
Synchronised Manual Transmission. | |||
Automated Manual Transmission or Automatic Mechanically-engaged Transmission. | |||
Automatic Powershifting Transmission. | |||
‘Case S’ means the serial arrangement of a torque converter and the connected mechanical parts of the transmission. | |||
‘Case P’ means the parallel arrangement of a torque converter and the connected mechanical parts of the transmission (e.g. in power split installations). | |||
European Modular System (EMS) in accordance with Council Directive 96/53/EC of 25 July 1996 laying down for certain road vehicles circulating within the Community the maximum authorized dimensions in national and international traffic and the maximum authorized weights in international traffic (OJ L 235, 17.9.1996, p. 59). | |||
World Harmonized Transient Driving Cycle. | |||
Worldwide Harmonised Steady state Cycle. |
PART C: AIR DRAG VALUE (CDXA) RANGES FOR THE PURPOSE OF PUBLICATION IN ACCORDANCE WITH ARTICLE 6
For the purpose of making publicly available the CdxA value specified in data entry 23 in accordance with Article 6, the Commission shall use the ranges defined in the following table containing the corresponding range for each CdxA value:
Range | CdxA value [m2] | |
---|---|---|
Min CdxA (CdxA ≥ min CdxA) | Max CdxA (CdxA < MaxCdxA) | |
A1 | 0,0 | 3,0 |
A2 | 3,0 | 3,15 |
A3 | 3,15 | 3,31 |
A4 | 3,31 | 3,48 |
A5 | 3,48 | 3,65 |
A6 | 3,65 | 3,83 |
A7 | 3,83 | 4,02 |
A8 | 4,02 | 4,22 |
A9 | 4,22 | 4,43 |
A10 | 4,43 | 4,65 |
A11 | 4,65 | 4,88 |
A12 | 4,88 | 5,12 |
A13 | 5,12 | 5,38 |
A14 | 5,38 | 5,65 |
A15 | 5,65 | 5,93 |
A16 | 5,93 | 6,23 |
A17 | 6,23 | 6,54 |
A18 | 6,54 | 6,87 |
A19 | 6,87 | 7,21 |
A20 | 7,21 | 7,57 |
A21 | 7,57 | 7,95 |
A22 | 7,95 | 8,35 |
A23 | 8,35 | 8,77 |
A24 | 8,77 | 9,21 |