- Latest available (Revised)
- Point in Time (31/01/2020)
- Original (As adopted by EU)
Commission Delegated Regulation (EU) 2020/22 of 31 October 2019 amending Annexes I and III to Regulation (EU) 2019/631 of the European Parliament and of the Council as regards the monitoring of CO2 emissions from new light commercial vehicles type-approved in a multi-stage process (Text with EEA relevance)
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).
Point in time view as at 31/01/2020.
There are currently no known outstanding effects for the Commission Delegated Regulation (EU) 2020/22.
Revised legislation carried on this site may not be fully up to date. At the current time any known changes or effects made by subsequent legislation have been applied to the text of the legislation you are viewing by the editorial team. Please see ‘Frequently Asked Questions’ for details regarding the timescales for which new effects are identified and recorded on this site.
in point 4 of Part B of Annex I, the definition of ‘Mø’ is replaced by the following:
is the average of the mass (M) of the new light commercial vehicles of the manufacturer registered in the relevant target year in kilograms (kg);
Where,
in the case of a complete vehicle, M is the mass in running order of that vehicle
in the case of a complete base vehicle related to a completed vehicle, M is the mass in running order of that base vehicle
in the case of an incomplete base vehicle related to a completed vehicle, M is the monitoring mass (Mmon) of that base vehicle, determined in accordance with the following formula:
Mmon = MRObase x B0
Where,
is the mass in running order of the base vehicle concerned
is as defined in point 1.2.4(a) of Part A of Annex III.’;
in Annex III, Part A is amended as follows:
point 1.2 is replaced by the following:
Completed vehicles registered as N1 vehicles
Reporting by Member States
The format set out in Section 2 of Part C shall be used for the reporting of data relating to completed N1 vehicles.
The vehicle identification number referred to in point (o) of point 1.1 shall not be made public.
Completed vehicles type-approved in accordance with Regulation (EC) No 692/2008
Member States shall for calendar year 2020 record the following detailed data with regard to:
the incomplete base vehicle: the data specified in points (a), (b), (c), (d), (e), (g), (h), (i), (n) and (o) of point 1.1, or, instead of the data specified in points (h) and (i), the default added mass provided as part of the type-approval information specified in point 2.17.2 of Annex I to Directive 2007/46/EC;
the complete base vehicle: the data specified in points (a), (b), (c), (d), (e), (g), (h), (i), (n) and (o) of point 1.1;
the completed vehicle: the data specified in points (a), (f), (g), (h), (j), (k), (l), (m) and (o) of point 1.1.
Where any of the data referred to in points (a) and (b) of the first subparagraph cannot be provided for the base vehicle, Member States shall provide data with regard to the completed vehicle instead.
Completed vehicles of category N1 type-approved in accordance with Annex XXI to Regulation (EU) 2017/1151
For each new completed vehicle registered in 2020 and subsequent calendar years, Member States shall as a minimum report the detailed data specified in points (a), (f), (g), (h), (o), (p) and (r) of point 1.1.
Reporting by manufacturers
For each new completed vehicle of category N1, type-approved in accordance with Annex XXI to Regulation (EU) 2017/1151 registered in 2020 and subsequent calendar years, the manufacturer of the related base vehicle shall report to the Commission by 28 February each year, starting from 2021, the following data relating to the base vehicle:
where the completed vehicle is based on an incomplete base vehicle:
vehicle identification number;
vehicle family identifier as referred to in paragraph 5.0 of Annex XXI to Regulation (EU) 2017/1151;
monitoring CO2 emissions determined in accordance with point 1.2.4;
frontal area, specifying the applicable option as referred to in point 1.2.4(c);
rolling resistance, as referred to in point 1.2.4(b);
monitoring mass, determined in accordance with point 4.1 of Part B of Annex I;
mass in running order;
mass representative of the vehicle load as defined in point 1.2.4(a);
where the completed vehicle is based on a complete base vehicle:
vehicle identification number;
vehicle family identifier as referred to in point (a)(ii) of this paragraph;
specific CO2 emissions of the base vehicle;
mass in running order.
Calculation of the average specific emissions of CO2 and the specific emission target
The Commission shall use the values reported by a base vehicle manufacturer in accordance with point 1.2.2 to calculate its average specific emissions of CO2 and the specific emission target in the calendar year in which the related completed vehicle is registered, except where the conditions referred to in point 1.2.5 are met in which case the data for the completed vehicles shall be used.
Where the data referred to in point 1.2.2 is not reported by the manufacturer of the base vehicle, the specific CO2 emissions reported by the Member States in accordance with point 1.2.1 with regard to the related completed vehicle shall be used for the calculation of the average specific emissions of CO2 and the specific emissions target of the manufacturer concerned.
Calculation of the monitoring CO2 emissions in the case of incomplete base vehicles
A manufacturer shall, starting from calendar year 2020, calculate the monitoring CO2 emissions for each of its individual incomplete base vehicles in accordance with the interpolation method referred to in points 3.2.3.2 or 3.2.4 of Sub-Annex 7 to Annex XXI to Regulation (EU) 2017/1151, using the same method as that applied for the EC type-approval of the base vehicle with regard to its emissions, where the terms shall be as defined in those points with the following exceptions:
Mass of the individual vehicle
The term ‘TMind’ referred to in points 3.2.3.2.2.1 or 3.2.4.1.1.1 of Sub-Annex 7 to Annex XXI to Regulation (EU) 2017/1151 shall be replaced by the base vehicle default mass, DMbase. Where DMbase is lower than the test mass of vehicle low, TML, of the interpolation family, TMind shall be replaced by TML. Where DMbase is higher than the test mass of vehicle high, TMH, of the interpolation family, TMind shall be replaced by TMH.
DMbase shall be determined in accordance with the following formula:
DMbase = MRObase × B0 + 25 kg + MVL
Where,
is the mass in running order of the base vehicle as defined in point 3.2.5 of Annex XXI to Regulation (EU) 2017/1151;
is the body mass value of 1,375;
is the mass representative of the vehicle load, which means 28 per cent of the maximum vehicle load, where maximum vehicle load is defined as the technically permissible maximum laden mass minus the mass in running order of the base vehicle multiplied by B0, minus 25 kg.
The value of B0 shall be adjusted by 31 October 2021 on the basis of the mass in running order of the incomplete base vehicles for all completed vehicles registered in calendar years 2018, 2019, and 2020, calculated in accordance with the below formulas. The new B0 value shall apply from 1 January 2022 until 31 December 2024.
Formula 1:
Where,
is the value Ay as calculated in Formula 2 for the relevant calendar year
is the number of incomplete base vehicles related to completed vehicles registered in the calendar year
Formula 2:
Where,
is the average of the ratio between Mfi and Mbi for each of the calendar years 2018 to 2020;
is the mass in running order of the incomplete base vehicle increased by the default added mass as defined in Section 5 of Annex XII to Regulation (EC) No 692/2008;
is the mass in running order of the incomplete base vehicle;
is the number of incomplete base vehicles related to completed vehicles registered in the calendar year.
Rolling resistance of the individual vehicle
The rolling resistance of the base vehicle shall be used for the purposes of point 3.2.3.2.2.2 or 3.2.4.1.1.2 of Sub-Annex 7 to Annex XXI to Regulation (EU) 2017/1151.
Frontal area
In the case of an incomplete base vehicle that belongs to a road load matrix family, the manufacturer shall determine the term ‘Af’ referred to in point 3.2.3.2.2.3 of Sub-Annex 7 to Annex XXI to Regulation (EU) 2017/1151 in accordance with one of the following options:
frontal area of the representative vehicle of the road load matrix family, in m2;
the mean value of the frontal area of vehicle high and vehicle low of the interpolation family, in m2;
the frontal area of the vehicle high of the interpolation family, in case the interpolation method is not used, in m2.
In the case of an incomplete base vehicle that does not belong to a road load matrix family, the frontal area value of vehicle high of the interpolation family shall be used.
Representativeness of the monitoring CO2 value
The Commission shall each year assess the representativeness of the average of the monitoring CO2 emissions reported by the base vehicle manufacturer as compared to the average of the specific emissions of CO2 of the related completed vehicles registered in the relevant calendar year. The Commission shall inform the manufacturer of the base vehicle of the divergence found between those values.
In case a divergence by 4 % or more is found during each of two successive calendar years, the Commission shall use the average of the specific emissions of CO2 of the completed vehicles in the following calendar year to calculate the average specific emissions of CO2 of the base vehicle manufacturer or the pool in that year.’;
point 2 is replaced by the following:
The details referred to in point 1 shall be taken from the certificate of conformity issued by the manufacturer of the relevant light commercial vehicle or be consistent with it. For those details that are not available in the certificate of conformity, details shall be taken from the type approval documentation or from the information reported by the base vehicle manufacturer pursuant to point 1.2.3. Member States shall put the necessary measures in place to ensure adequate accuracy in the monitoring procedure. Where the certificate of conformity specifies both a minimum and a maximum mass for a light commercial vehicle, the Member States shall use only the maximum figure for the purpose of this Regulation. In the case of bi-fuelled vehicles (petrol/gas) the certificates of conformity of which bear specific CO2 emission figures for both types of fuel, Member States shall use only the figure measured for gas.’
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Point in Time: This becomes available after navigating to view revised legislation as it stood at a certain point in time via Advanced Features > Show Timeline of Changes or via a point in time advanced search.
Geographical Extent: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Show Timeline of Changes: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
This timeline shows the different versions taken from EUR-Lex before exit day and during the implementation period as well as any subsequent versions created after the implementation period as a result of changes made by UK legislation.
The dates for the EU versions are taken from the document dates on EUR-Lex and may not always coincide with when the changes came into force for the document.
For any versions created after the implementation period as a result of changes made by UK legislation the date will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. For further information see our guide to revised legislation on Understanding Legislation.
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: