- Latest available (Revised)
- Point in Time (06/04/2007)
- Original (As enacted)
Version Superseded: 22/07/2009
Point in time view as at 06/04/2007. This version of this provision has been superseded.
You are viewing this legislation item as it stood at a particular point in time. A later version of this or provision, including subsequent changes and effects, supersedes this version.
Note the term provision is used to describe a definable element in a piece of legislation that has legislative effect – such as a Part, Chapter or section.
There are currently no known outstanding effects for the Hallmarking Act 1973, Section 5.
Revised legislation carried on this site may not be fully up to date. At the current time any known changes or effects made by subsequent legislation have been applied to the text of the legislation you are viewing by the editorial team. Please see ‘Frequently Asked Questions’ for details regarding the timescales for which new effects are identified and recorded on this site.
(1)Subject to subsections (3) to (5) below, it shall be an offence for any person to make an addition, alteration or repair to an article bearing approved hallmarks, except in accordance with the written consent of an assay office.
(2)Subject to subsection (3) below, it shall be an offence for any person to remove, alter or deface any mark struck on an article, except in accordance with the written consent of an assay office.
For the purposes of this subsection “mark” means a sponsor’s mark, any approved hallmark, the word “filled”, the word “metal” or any other word for the time being prescribed by or under section 4 of, or Schedule 2 to, this Act.
(3)It shall not be an offence under subsection (1) or (2) above to batter an article so as to render it fit only for remanufacture.
(4)It shall not be an offence under subsection (1) above to make an addition to an article which is not a new ware if the character of the article, and the purposes for which it can be used, remain unaltered and—
(a)the addition is of the same precious metal as that of the article;
(b)the metal added to the article is of a fineness not less than the standard of fineness of the article; and
(c)the amount of metal added does not exceed the lesser of—
(i)1 gram of gold, 5 grams of silver or 0·5 grams of platinum, as the case may be; and
(ii)50 per cent. of the weight of the article immediately before the addition was made.
(5)It shall not be an offence under subsection (1) above to add a coating, of a thickness not exceeding 2 micrometres at any point, to the whole or any part of—
(a)an article of gold, if the coating is of gold of a fineness not less than the standard of fineness of the article; or
(b)an article of silver, if the coating is of silver of a fineness not less than the standard of fineness of the article; or
(c)an article of silver, if the coating is of gold of not less than the minimum fineness; or
(d)an article of gold, silver or platinum, if the coating is of rhodium.
(6)In giving any consent for the purposes of subsection (1) or (2) above, an assay office may make it a condition of the consent that the article concerned, or any addition made to it, be further assayed and struck with—
(a)the sponsor’s mark; and
(b)such of the approved hallmarks as may be specified in directions issued by the Council for the purposes of this subsection or, in the absence of any such directions, such of the approved hallmarks as may be determined by the assay office.
(7)If—
(a)an application for consent under subsection (1) or (2) above has been refused by an assay office; and
(b)the applicant has referred the matter to the Council, in writing;
the Council shall consider the case and, if they are of the opinion that the assay office were acting unreasonably in withholding the consent applied for, they shall direct the assay office to grant the consent.
(8)Without prejudice to subsection (6) above, it shall be the duty of an assay office to whom a direction has been given under subsection (7) above to comply with the direction.
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As Enacted or Made): The original version of the legislation as it stood when it was enacted or made. No changes have been applied to the text.
Point in Time: This becomes available after navigating to view revised legislation as it stood at a certain point in time via Advanced Features > Show Timeline of Changes or via a point in time advanced search.
Geographical Extent: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Show Timeline of Changes: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
This timeline shows the different points in time where a change occurred. The dates will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. The first date in the timeline will usually be the earliest date when the provision came into force. In some cases the first date is 01/02/1991 (or for Northern Ireland legislation 01/01/2006). This date is our basedate. No versions before this date are available. For further information see the Editorial Practice Guide and Glossary under Help.
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: