Spray suppression devicesE+W+S
64.—(1) Save as provided in paragraph (2), this regulation applies to every wheeled goods vehicle which is—
(a)a motor vehicle first used on or after 1st April 1986 having a maximum gross weight exceeding 12,000 kg;
(b)a trailer manufactured on or after 1st May 1985 having a maximum gross weight exceeding 3500 kg; or
(c)a trailer, whenever manufactured, having a maximum gross weight exceeding 16,000 kg and 2 or more axles.
(2) This regulation does not apply to—
(a)a motor vehicle so constructed that the driving power of its engine is, or can by use of its controls be, transmitted to all the wheels on at least one front axle and on at least one rear axle;
(b)a motor vehicle of which no part which lies within the specified area is less than 400 mm vertically above the ground when the vehicle is standing on reasonably flat ground;
(c)a works truck;
(d)a works trailer;
(e)a broken down vehicle;
(f)a motor vehicle which has a maximum speed not exceeding 30 mph;
(g)a vehicle of a kind specified in sub-paragraphs (b), (c), (d), (e), (f), (g), (h), (j), (k), (o) or (p) of regulation 51(2);
(h)a vehicle specially designed, and not merely adapted, for the carriage and mixing of liquid concrete; or
(i)a vehicle which is being driven or towed to a place where by previous arrangement a device is to be fitted so that it complies with the requirements specified in paragraph (3).
[F1(2A) This regulation shall not apply to a vehicle fitted with a spray-suppression system in accordance with the requirements of Annex III of Community Directive 91/226(3) if the spray suppression devices with which the vehicle is equipped are legibly and permanently marked with a designated approval mark.]
(3) A vehicle to which this regulation applies and which is of a class specified in an item in column 2 of the Table shall not be used on a road on or after the date specified in column 3 in that item, unless it is fitted in relation to the wheels on each of its axles, with such containment devices as satisfy the technical requirements and other provisions about containment devices specified in the British Standard Specification, provided that in the case of a containment device fitted before 1st January 1985 the said requirements shall be deemed to be complied with if that containment device substantially conforms to those requirements.
TABLE
(regulation 64(3))
| 1 | 2 | 3 |
|---|---|---|
| Item | Class of Vehicle | Date |
| 1 | A trailer manufactured before 1st January 1975 | 1st October 1987 |
| 2 | A trailer manufactured on or after 1st January 1975 but before 1st May 1985 | 1st October 1986 |
| 3 | A trailer manufactured on or after 1st May 1985 | 1st May 1985 |
| 4 | A motor vehicle | 1st April 1986 |
(4) In this regulation—
[F2“the British Standard Specification” means
in relation to a containment device fitted before 1st May 1987, Part 1a of the amended Specification and Part 2 of the original Specification; and
in relation to a containment device fitted on or after 1st May 1987, Part 1a and Part 2a of the amended Specification;
[F3“designated approval mark” means the marking designated as an approval mark by regulation 5 of the Approval Marks Regulations and shown at item 30 in Schedule 4 to those Regulations;]
“the original Specification” means
“the amended Specification” means
“containment device” means
“the specified area” means
(5) Nothing in this regulation derogates from any requirement specified in regulation 63.
Textual Amendments
F1Reg. 64(2A) inserted (1.4.1992) by The Road Vehicles (Construction and Use) (Amendment) (No. 3) Regulations 1992 (S.I. 1992/646), regs. 1, 2(2)
F2Words in reg. 64(4) substituted (10.10.1986) by The Road Vehicles (Construction and Use) (Amendment) Regulations 1986 (S.I. 1986/1597), regs. 1, 4 (with reg. 3)
F3Words in reg. 64(4) inserted (1.4.1992) by The Road Vehicles (Construction and Use) (Amendment) (No. 3) Regulations 1992 (S.I. 1992/646), regs. 1, 2(3)
Commencement Information
I1Reg. 64 in force at 11.8.1986, see reg. 1