The Supply of Machinery (Safety) Regulations 2008

Annex IV machinery manufactured fully in accordance with [F1 designated] standards and fully covered by such standards E+W+S

11.—(1) This regulation applies to machinery—

(a) which falls within a category which is referred to in Annex IV (Part 4 of Schedule 2); and

(b) in respect of which both of the following conditions are satisfied—

(i) that the machinery is manufactured in accordance with [F2 designated] standards; and

(ii) that the [F3 designated] standards in accordance with which it is manufactured cover all the applicable essential health and safety requirements.

(2) Where this regulation applies, the responsible person shall follow one of the following conformity assessment procedures—

(a) the conformity assessment procedure with internal checks on the manufacture of machinery prescribed in Annex VIII (Part 8 of Schedule 2); or

(b) the [F4 Type-] examination procedure prescribed in Annex IX (Part 9 of Schedule 2) and the internal checks on the manufacture of machinery prescribed in Annex VIII, point 3; or

(c) the full quality assurance procedure prescribed in Annex X (Part 10 of Schedule 2).

Extent Information

E1 This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only

Textual Amendments

F1 Word in reg. 11 heading substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 12 para. 7(a) (with Sch. 12 para. 22) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F2 Word in reg. 11(1)(b)(i) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 12 para. 7(a) (with Sch. 12 para. 22) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F3 Word in reg. 11(1)(b)(ii) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 12 para. 7(a) (with Sch. 12 para. 22) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

F4 Word in reg. 11(2)(b) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 12 para. 7(b) (with Sch. 12 para. 22) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

Annex IV machinery manufactured fully in accordance with published harmonised standards and fully covered by such standards N.I.

11.—(1) This regulation applies to machinery—

(a) which falls within a category which is referred to in Annex IV (Part 4 of Schedule 2); and

(b) in respect of which both of the following conditions are satisfied—

(i) that the machinery is manufactured in accordance with published harmonised standards; and

(ii) that the published harmonised standards in accordance with which it is manufactured cover all the applicable essential health and safety requirements.

(2) Where this regulation applies, the responsible person shall follow one of the following conformity assessment procedures—

(a) the conformity assessment procedure with internal checks on the manufacture of machinery prescribed in Annex VIII (Part 8 of Schedule 2); or

(b) the EC type-examination procedure prescribed in Annex IX (Part 9 of Schedule 2) and the internal checks on the manufacture of machinery prescribed in Annex VIII, point 3; or

(c) the full quality assurance procedure prescribed in Annex X (Part 10 of Schedule 2).

Extent Information

E2 This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only