xmlns:atom="http://www.w3.org/2005/Atom" xmlns:atom="http://www.w3.org/2005/Atom"
41.—(1) A product which is in conformity with a [F1designated] standard (or part of such a standard) F2... is to be presumed to be in conformity with the essential requirements covered by that standard (or that part of that standard).
(2) The presumption in paragraph (1) is rebuttable.
Extent Information
E1This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F1Word in reg. 41(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 24(a) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F2Words in reg. 41(1) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 24(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I1Reg. 41 in force at 3.8.2017, see reg. 1
41.—(1) A product which is in conformity with a harmonised standard (or part of such a standard) the reference to which has been published in the Official Journal of the European Union is to be presumed to be in conformity with the essential requirements covered by that standard (or that part of that standard).
(2) The presumption in paragraph (1) is rebuttable.
Extent Information
E12This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I15Reg. 41 in force at 3.8.2017, see reg. 1
42. Before placing a product on the market the manufacturer must apply the conformity assessment procedures set out in the modules set out in [F3Schedule 15] and referred to in regulations 44 (design and construction) to 47 (noise emissions: personal watercraft).
Extent Information
E2This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F3Words in reg. 42 substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 25 (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I2Reg. 42 in force at 3.8.2017, see reg. 1
42. Before placing a product on the market the manufacturer must apply the conformity assessment procedures set out in the modules set out in Annex II of Decision 768/2008 and referred to in regulations 44 (design and construction) to 47 (noise emissions: personal watercraft).
Extent Information
E13This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I16Reg. 42 in force at 3.8.2017, see reg. 1
43.—(1) Before putting a product into service a private importer must apply the procedure referred to in regulation 48 (requirements of the post-construction assessment) to that product if the manufacturer of the product has not already carried out the conformity assessment for the product concerned.
(2) Any person must, before placing or putting into service on the market—
(a)a propulsion engine or watercraft which has had a major engine modification or major craft conversion; or
(b)a watercraft which has had a change in its intended purpose so that it falls within scope of these Regulations
apply the procedure referred to in regulation 48 (requirements of the post-construction assessment).
(3) Any person placing on the market a watercraft built for own use before the end of the five-year period beginning on the day on which the watercraft was put into service, must apply the procedure referred to in regulation 48 before placing the watercraft on the market.
Commencement Information
I3Reg. 43 in force at 3.8.2017, see reg. 1
44.—(1) With regard to the design and construction of recreational craft, the following conformity assessment procedures set out in [F4Schedule 15] apply—
(a)for design categories A and B referred to in paragraph 1 of Part A of Schedule 1—
(i)for recreational craft of hull length from 2.5 metres to less than 12 metres, any of the following modules—
(aa)Module A1 (internal production control plus supervised product testing);
(bb)Module B [F5(type examination)] together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on product quality assurance) or Module F (conformity to type based on product verification);
(cc)Module G (conformity based on unit verification);
(dd)Module H (conformity based on full quality assurance);
(ii)for recreational craft of hull length from 12 metres to less than 24 metres, any of the following modules—
(aa)Module B [F5(type examination)] together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification);
(bb)Module G (conformity based on unit verification);
(cc)Module H (conformity based on full quality assurance);
(b)for design category C referred to in paragraph 1 of Part A of Schedule 1—
(i)for recreational craft of hull length from 2.5 metres to less than 12 metres where the [F6designated] standards relating to paragraphs 3.2 and 3.3 of Part A of Schedule 1 are complied with, any of the following modules—
(aa)Module A (internal production control);
(bb)Module A1 (internal production control plus supervised product testing);
(cc)Module B ([F7type examination] together with Module C (conformity to type based on internal production control)), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification);
(dd)Module G (conformity based on unit verification);
(ee)Module H (conformity based on full quality assurance);
(ii)for recreational craft of hull length from 2.5 metres to less than 12 metres where the [F6designated] standards relating to paragraphs 3.2 and 3.3 of Part A of Schedule 1 are not complied with, any of the following modules—
(aa)Module A1 (internal production control plus supervised testing);
(bb)Module B ([F7type examination]) together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification;
(cc)Module G (conformity based on unit verification);
(dd)Module H (conformity based on full quality assurance);
(iii)for recreational craft of hull length from 12 metres to 24 metres, any of the following modules—
(aa)Module B ([F7type examination]) together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification;
(bb)Module G (conformity based on unit verification);
(cc)Module H (conformity based on full quality assurance);
(c)for design category D referred to in paragraph 1 of Part A of Schedule 1 for recreational craft of hull length of 2.5 metres to 24 metres, any of the following modules—
(i)Module A (internal production control);
(ii)Module A1 (internal production control plus supervised testing);
(iii)Module B ([F8type examination] together with Module C (conformity to type based on internal production control)), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on product quality assurance) or Module F (conformity to type based on product verification);
(iv)Module G (conformity based on unit verification);
(v)Module H (conformity based on full quality assurance).
(2) With regard to the design and construction of personal watercraft, any of the following procedures set out in [F9Schedule 15] apply—
(a)Module A (internal production control);
(b)Module A1 (internal production control plus supervised testing);
(c)Module B ([F10type examination] together with Module C conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification);
(d)Module G (conformity based on unit verification);
(e)Module H (conformity based on full quality assurance).
(3) With regard to the design and construction of components any of the following procedures set out in [F11Schedule 15] apply—
(a)Module B [F12(type examination)] together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification);
(b)Module G (conformity based on unit verification);
(c)Module H (conformity based on full quality assurance).
Extent Information
E3This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F4Words in reg. 44(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(2)(a) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F5Words in reg. 44(1)(a) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(2)(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F6Word in reg. 44(1)(b) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(2)(c)(ii) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F7Words in reg. 44(1)(b) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(2)(c)(i) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F8Words in reg. 44(1)(c)(iii) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(2)(d) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F9Words in reg. 44(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(3) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F10Words in reg. 44(2)(c) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(4) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F11Words in reg. 44(3) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(3) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F12Words in reg. 44(3)(a) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 26(5) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I4Reg. 44 in force at 3.8.2017, see reg. 1
44.—(1) With regard to the design and construction of recreational craft, the following conformity assessment procedures set out in Annex II to Decision 768/2008/EC apply—
(a)for design categories A and B referred to in paragraph 1 of Part A of Schedule 1—
(i)for recreational craft of hull length from 2.5 metres to less than 12 metres, any of the following modules—
(aa)Module A1 (internal production control plus supervised product testing);
(bb)Module B (EU-type examination) together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on product quality assurance) or Module F (conformity to type based on product verification);
(cc)Module G (conformity based on unit verification);
(dd)Module H (conformity based on full quality assurance);
(ii)for recreational craft of hull length from 12 metres to less than 24 metres, any of the following modules—
(aa)Module B (EU-type examination) together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification);
(bb)Module G (conformity based on unit verification);
(cc)Module H (conformity based on full quality assurance);
(b)for design category C referred to in paragraph 1 of Part A of Schedule 1—
(i)for recreational craft of hull length from 2.5 metres to less than 12 metres where the harmonised standards relating to paragraphs 3.2 and 3.3 of Part A of Schedule 1 are complied with, any of the following modules—
(aa)Module A (internal production control);
(bb)Module A1 (internal production control plus supervised product testing);
(cc)Module B (EU type-examination together with Module C (conformity to type based on internal production control)), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification);
(dd)Module G (conformity based on unit verification);
(ee)Module H (conformity based on full quality assurance);
(ii)for recreational craft of hull length from 2.5 metres to less than 12 metres where the harmonised standards relating to paragraphs 3.2 and 3.3 of Part A of Schedule 1 are not complied with, any of the following modules—
(aa)Module A1 (internal production control plus supervised testing);
(bb)Module B (EU type-examination) together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification;
(cc)Module G (conformity based on unit verification);
(dd)Module H (conformity based on full quality assurance);
(iii)for recreational craft of hull length from 12 metres to 24 metres, any of the following modules—
(aa)Module B (EU type-examination) together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification;
(bb)Module G (conformity based on unit verification);
(cc)Module H (conformity based on full quality assurance);
(c)for design category D referred to in paragraph 1 of Part A of Schedule 1 for recreational craft of hull length of 2.5 metres to 24 metres, any of the following modules—
(i)Module A (internal production control);
(ii)Module A1 (internal production control plus supervised testing);
(iii)Module B (EU- type examination together with Module C (conformity to type based on internal production control)), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on product quality assurance) or Module F (conformity to type based on product verification);
(iv)Module G (conformity based on unit verification);
(v)Module H (conformity based on full quality assurance).
(2) With regard to the design and construction of personal watercraft, any of the following procedures set out in Annex II to Decision 768/2008/EC apply—
(a)Module A (internal production control);
(b)Module A1 (internal production control plus supervised testing);
(c)Module B (EU type-examination together with Module C conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification);
(d)Module G (conformity based on unit verification);
(e)Module H (conformity based on full quality assurance).
(3) With regard to the design and construction of components any of the following procedures set out in Annex II to Decision 768/2008/EC apply—
(a)Module B (EU type-examination) together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on quality product assurance) or Module F (conformity to type based on product verification);
(b)Module G (conformity based on unit verification);
(c)Module H (conformity based on full quality assurance).
Extent Information
E14This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I17Reg. 44 in force at 3.8.2017, see reg. 1
45. With regard to exhaust emissions, for products referred to in regulation 3(1)(d) and (e), the engine manufacturer must apply the following procedures set out in [F13Schedule 15]—
(a)where the tests are conducted using the [F14designated] standard, any of the following modules—
(i)Module B [F15(type examination)] together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on product quality assurance) or Module F (conformity to type based on product verification);
(ii)Module G (conformity based on unit verification);
(iii)Module H (conformity based on full quality assurance);
(b)where the tests are conducted without using the [F16designated] standard, either of the following modules—
(i)Module B [F17(type examination)] together with Module C1 (conformity to type based on internal production control plus supervised product testing);
(ii)Module G (conformity based on unit verification).
Extent Information
E4This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F13Words in reg. 45 substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 27(a) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F14Word in reg. 45(a) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 27(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F15Words in reg. 45(a)(i) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 27(c) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F16Word in reg. 45(b) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 27(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F17Words in reg. 45(b)(i) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 27(d) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I5Reg. 45 in force at 3.8.2017, see reg. 1
45. With regard to exhaust emissions, for products referred to in regulation 3(1)(d) and (e), the engine manufacturer must apply the following procedures set out in Annex II to Decision 768/2008/EC—
(a)where the tests are conducted using the harmonised standard, any of the following modules—
(i)Module B (EU-type examination) together with Module C (conformity to type based on internal production control), Module D (conformity to type based on quality assurance of the production process), Module E (conformity to type based on product quality assurance) or Module F (conformity to type based on product verification);
(ii)Module G (conformity based on unit verification);
(iii)Module H (conformity based on full quality assurance);
(b)where the tests are conducted without using the harmonised standard, either of the following modules—
(i)Module B (the EU- type examination) together with Module C1 (conformity to type based on internal production control plus supervised product testing);
(ii)Module G (conformity based on unit verification).
Extent Information
E15This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I18Reg. 45 in force at 3.8.2017, see reg. 1
46.—(1) The manufacturer must apply the relevant procedures in paragraphs (2) to (4) as set out in [F18Schedule 15] with regard to the noise emissions for recreational craft with—
(a)stern drive propulsion engines without integral exhausts or inboard propulsion engine installations; and
(b)stern drive propulsion engines without integral exhausts or inboard propulsion engine installations which are subject to major craft conversion and are subsequently placed on the market within the period of 5 years from the day on which that conversion was completed.
(2) Where tests are conducted using the [F19designated] standard for noise measurement, any of the following modules apply—
(a)Module A1 (internal production plus supervised product testing);
(b)Module G (conformity based on unit verification);
(c)Module H (conformity based on full quality assurance).
(3) Where tests are conducted without using the [F20designated] standard for noise measurement, Module G (conformity based on unit verification) applies.
(4) Where the Froude number of power displacement ratio method is used for assessment, any of the following modules apply—
(a)Module A (internal production control);
(b)Module G (conformity based on unit verification);
(c)Module H (conformity based on full quality assurance).
Extent Information
E5This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F18Words in reg. 46(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 28(a) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F19Word in reg. 46(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 28(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F20Word in reg. 46(3) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 28(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I6Reg. 46 in force at 3.8.2017, see reg. 1
46.—(1) The manufacturer must apply the relevant procedures in paragraphs (2) to (4) as set out in Annex II to Decision 768/2008/EC with regard to the noise emissions for recreational craft with—
(a)stern drive propulsion engines without integral exhausts or inboard propulsion engine installations; and
(b)stern drive propulsion engines without integral exhausts or inboard propulsion engine installations which are subject to major craft conversion and are subsequently placed on the market within the period of 5 years from the day on which that conversion was completed.
(2) Where tests are conducted using the harmonised standard for noise measurement, any of the following modules apply—
(a)Module A1 (internal production plus supervised product testing);
(b)Module G (conformity based on unit verification);
(c)Module H (conformity based on full quality assurance).
(3) Where tests are conducted without using the harmonised standard for noise measurement, Module G (conformity based on unit verification) applies.
(4) Where the Froude number of power displacement ratio method is used for assessment, any of the following modules apply—
(a)Module A (internal production control);
(b)Module G (conformity based on unit verification);
(c)Module H (conformity based on full quality assurance).
Extent Information
E16This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I19Reg. 46 in force at 3.8.2017, see reg. 1
47.—(1) The personal watercraft or engine manufacturer must apply the relevant procedure in paragraphs (2) or (3) as set out in [F21Schedule 15], with regard to noise emissions for—
(a)personal watercraft and outboard propulsion engines; and
(b)stern drive propulsion engines with integral exhausts intended for installation on recreational craft.
(2) Where the tests are conducted using the [F22designated] standard for noise measurement, any of the following modules apply—
(a)Module A1 (internal production control plus supervised product testing);
(b)Module G (conformity based on unit verification);
(c)Module H (conformity based on full quality assurance).
(3) Where the tests are conducted without using the [F23designated] standard for noise measurement, Module G (conformity based on unit verification) applies.
Extent Information
E6This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F21Words in reg. 47(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 29(a) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F22Word in reg. 47(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 29(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F23Word in reg. 47(3) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 29(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I7Reg. 47 in force at 3.8.2017, see reg. 1
47.—(1) The personal watercraft or engine manufacturer must apply the relevant procedure in paragraphs (2) or (3) as set out in Annex II to Decision 768/2008/EC, with regard to noise emissions for—
(a)personal watercraft and outboard propulsion engines; and
(b)stern drive propulsion engines with integral exhausts intended for installation on recreational craft.
(2) Where the tests are conducted using the harmonised standard for noise measurement, any of the following modules apply—
(a)Module A1 (internal production control plus supervised product testing);
(b)Module G (conformity based on unit verification);
(c)Module H (conformity based on full quality assurance).
(3) Where the tests are conducted without using the harmonised standard for noise measurement, Module G (conformity based on unit verification) applies.
Extent Information
E17This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I20Reg. 47 in force at 3.8.2017, see reg. 1
48. A post-construction assessment must be carried out in accordance with the process set out in Schedule 5.
Commencement Information
I8Reg. 48 in force at 3.8.2017, see reg. 1
49.—[F24(1) Where an economic operator has a conformity assessment carried out on a product under Module B (EU-type examination) of Annex II to Decision 768/2008/EC in relation to a product, the conformity assessment must be carried out in the manner set out in Schedule 10.
(2) A production type may cover several versions of the assessed product, if—
(a)the differences between the versions of the product do not affect the level of safety and the other requirements concerning the performance of the product; and
(b)the different versions of the product are referred to in the corresponding EU-type examination certificate, if necessary by means of amendments to the original certificate.
(3) For the purposes of this regulation—
“production type” means an examination of the adequacy of the technical design of the watercraft through examination of the technical documentation specified in paragraph 3 of Schedule 10 and a specimen watercraft that is representative of the completed watercraft that is to be or has been produced by the manufacturer.]
Textual Amendments
F24Reg. 49 omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 30 (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I9Reg. 49 in force at 3.8.2017, see reg. 1
50.—(1) Where an economic operator has a conformity assessment carried out on a product under Module A1 (internal production control plus supervised product testing) [F25as set out in Schedule 15]—
(a)the product checks must be carried out on at least one watercraft that is representative of the watercraft that is to be or has been produced by the manufacturer; and
(b)the requirements set out in Schedule 6 apply.
F26(2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Extent Information
E7This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F25Words in reg. 50(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 31(a) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F26Reg. 50(2) omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 31(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I10Reg. 50 in force at 3.8.2017, see reg. 1
50.—(1) Where an economic operator has a conformity assessment carried out on a product under Module A1 (internal production control plus supervised product testing) of Annex II to Decision 768/2008/EC—
(a)the product checks must be carried out on at least one watercraft that is representative of the watercraft that is to be or has been produced by the manufacturer; and
(b)the requirements set out in Schedule 6 apply.
(2) The possibility, referred to in Modules A1 and C1 of Annex II of Decision 768/2008, of using an accredited in-house body to perform a conformity assessment under those modules is not applicable in relation to watercraft.
Extent Information
E18This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I21Reg. 50 in force at 3.8.2017, see reg. 1
51. Where an economic operator has a conformity assessment carried out on a product under Module F (conformity to type based on product verification) [F27as set out in Schedule 15], the procedure set out in Schedule 7 applies.
Extent Information
E8This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F27Words in reg. 51 substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 32 (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I11Reg. 51 in force at 3.8.2017, see reg. 1
51. Where an economic operator has a conformity assessment carried out on a product under Module F (conformity to type based on product verification) of Annex II to Decision 768/2008/EC, the procedure set out in Schedule 7 applies.
Extent Information
E19This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I22Reg. 51 in force at 3.8.2017, see reg. 1
52.—(1) This regulation applies where—
(a)an economic operator has a conformity assessment carried out on a watercraft under Module C (conformity to type based on internal production control) [F28set out in Schedule 15];
(b)Module C is used to assess the conformity of the product with the exhaust emission requirements of these Regulations; and
(c)the manufacturer is not working under a relevant quality system as described in Module H [F29set out in Schedule 15].
(2) [F30An approved] body chosen by the manufacturer must carry out product checks as required by Module C or have them carried out at random intervals to be determined by [F31the approved] body, in order to verify the quality of the internal checks on the product carried out under the manufacturer’s own checking measures.
(3) When the quality level appears unsatisfactory or when it seems necessary to verify the validity of the data presented by the manufacturer, the procedure set out in Schedule 8 applies.
Extent Information
E9This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F28Words in reg. 52(1)(a) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 33(a)(i) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F29Words in reg. 52(1)(c) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 33(a)(ii) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F30Words in reg. 52(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 33(b)(i) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F31Words in reg. 52(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 33(b)(ii) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I12Reg. 52 in force at 3.8.2017, see reg. 1
52.—(1) This regulation applies where—
(a)an economic operator has a conformity assessment carried out on a watercraft under Module C (conformity to type based on internal production control) of Annex II of Decision 768/2008/EC;
(b)Module C is used to assess the conformity of the product with the exhaust emission requirements of these Regulations; and
(c)the manufacturer is not working under a relevant quality system as described in Module H of Annex II to Decision 768/2008/EC.
(2) A notified body chosen by the manufacturer must carry out product checks as required by Module C or have them carried out at random intervals to be determined by the notified body, in order to verify the quality of the internal checks on the product carried out under the manufacturer’s own checking measures.
(3) When the quality level appears unsatisfactory or when it seems necessary to verify the validity of the data presented by the manufacturer, the procedure set out in Schedule 8 applies.
Extent Information
E20This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I23Reg. 52 in force at 3.8.2017, see reg. 1
53. The F33... declaration of conformity for a product must—
(a)state that the product complies with the essential requirements;
(b)contain the elements specified in regulations 44 to 47 for the relevant conformity assessment [F34procedure] in respect of the product; and
(c)be set out in accordance with the model structure set out in Schedule 4.
Extent Information
E10This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F32Word in reg. 53 heading substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 34(a) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F33Word in reg. 53 omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 34(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F34Word in reg. 53(b) inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 34(c) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I13Reg. 53 in force at 3.8.2017, see reg. 1
53. The EU declaration of conformity for a product must—
(a)state that the product complies with the essential requirements;
(b)contain the elements specified in regulations 44 to 47 for the relevant conformity assessment in respect of the product; and
(c)be set out in accordance with the model structure set out in Schedule 4.
Extent Information
E21This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I24Reg. 53 in force at 3.8.2017, see reg. 1
54.—[F36(1) The UK marking must be affixed visibly, legibly and indelibly—
(a)to the product; or
(b)where paragraph (1A) applies, to—
(i)a label affixed to the product; or
(ii)a document accompanying the product.]
[F37(1A) For a period of [F38seven years] beginning with IP completion day, the UK marking may be affixed to—
(a)a label affixed to the product; or
(b)a document accompanying the product.]
(2) Where [F39paragraph (1A) does not apply and] it is not possible or warranted, on account of the nature of a component to affix the [F40UK] marking in accordance with [F41paragraph (1)(a)], the [F40UK] marking must be affixed to—
(a)the packaging; and
(b)the accompanying documents.
(3) [F42Except where paragraph (3A) applies] where the product referred to in paragraph (1)—
(a)is a watercraft, the [F43UK] marking must be affixed to the watercraft builder’s plate and mounted separately from the watercraft identification number; or
(b)is a propulsion engine, the [F43UK] marking must be affixed on the engine.
[F44(3A) For a period of 24 months beginning with IP completion day, the UK marking may be affixed to—
(a)a label affixed to the watercraft or propulsion engine; or
(b)a document accompanying the watercraft or propulsion engine.]
(4) The [F45UK] marking must be followed by the identification number of the [F46approved] body where—
(a)that body is involved in the production control phase of the conformity assessment under Modules A (internal production control), A1 (internal production control plus supervised product testing) or C (conformity to type based on internal production control) set out in [F47Schedule 15]; or
(b)where a post construction assessment set out in Schedule 5 of these Regulations is being used.
(5) The identification number of the [F48approved] body must be affixed—
(a)by the [F48approved] body itself; or
(b)under the instructions of the [F48approved] body by the manufacturer.
Extent Information
E11This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only
Textual Amendments
F35Words in reg. 54 heading substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(a) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F36Reg. 54(1) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(b) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(a)); 2020 c. 1, Sch. 5 para. 1(1)
F37Reg. 54(1A) inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(ba) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(b)); 2020 c. 1, Sch. 5 para. 1(1)
F38Words in reg. 54(1A) substituted (E.W.S) (31.12.2022) by The Product Safety and Metrology (Amendment and Transitional Provisions) Regulations 2022 (S.I. 2022/1393), regs. 1(1), 3, Sch. 2
F39Words in reg. 54(2) inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(bb)(i) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(b)); 2020 c. 1, Sch. 5 para. 1(1)
F40Word in reg. 54(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(bb)(ii) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(b)); 2020 c. 1, Sch. 5 para. 1(1)
F41Words in reg. 54(2) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(bb)(iii) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(b)); 2020 c. 1, Sch. 5 para. 1(1)
F42Words in reg. 54(3) inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(bc)(i) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(b)); 2020 c. 1, Sch. 5 para. 1(1)
F43Word in reg. 54(3) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(bc)(ii) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(b)); 2020 c. 1, Sch. 5 para. 1(1)
F44Reg. 54(3A) inserted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(bd) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(b)); 2020 c. 1, Sch. 5 para. 1(1)
F45Word in reg. 54(4) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(be) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2020/1460, reg. 1(4), Sch. 3 para. 20(6)(b)); 2020 c. 1, Sch. 5 para. 1(1)
F46Word in reg. 54(4) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(ba) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2; S.I. 2019/1246, regs. 1(3), 16(a)); 2020 c. 1, Sch. 5 para. 1(1)
F47Words in reg. 54(4)(a) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(c) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F48Word in reg. 54(5) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 28 para. 35(d) (with Sch. 28 para. 41) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
Commencement Information
I14Reg. 54 in force at 3.8.2017, see reg. 1
54.—(1) The CE marking must be affixed visibly, legibly and indelibly to the product.
(2) Where it is not possible or warranted, on account of the nature of a component to affix the CE marking in accordance with paragraph (1), the CE marking must be affixed to—
(a)the packaging; and
(b)the accompanying documents.
(3) Where the product referred to in paragraph (1)—
(a)is a watercraft, the CE marking must be affixed to the watercraft builder’s plate and mounted separately from the watercraft identification number; or
(b)is a propulsion engine, the CE marking must be affixed on the engine.
(4) The CE marking must be followed by the identification number of the notified body where—
(a)that body is involved in the production control phase of the conformity assessment under Modules A (internal production control), A1 (internal production control plus supervised product testing) or C (conformity to type based on internal production control) set out in Annex II of Decision 768/2008; or
(b)where a post construction assessment set out in Schedule 5 of these Regulations is being used.
(5) The identification number of the notified body must be affixed—
(a)by the notified body itself; or
(b)under the instructions of the notified body by the manufacturer.
Extent Information
E22This version of this provision extends to Northern Ireland only; a separate version has been created for England and Wales and Scotland only
Commencement Information
I25Reg. 54 in force at 3.8.2017, see reg. 1
54A.—(1) Where the CE marking is affixed on the basis of an assessment or a certificate issued by a notified body established in the United Kingdom, a UK(NI) indication must be affixed in relation to the product, in accordance with this regulation.
(2) The UK(NI) indication must be affixed—
(a)visibly, legibly and indelibly; and
(b)before a product is placed on the market in Northern Ireland.
(3) The UK(NI) indication must accompany the CE marking, wherever that is affixed in accordance with regulation 54.
(4) The UK(NI) indication must be affixed by—
(a)the manufacturer; or
(b)the manufacturer's authorised representative.
(5) When placing a product on the market in Northern Ireland, an importer must ensure that the manufacturer has complied with their obligations under this regulation.]
Textual Amendments
54B.—(1) The Secretary of State must ensure that—
(a)each notified body established in the United Kingdom is assigned an identification number; and
(b)there is a register of—
(i)notified bodies established in the United Kingdom;
(ii)their notified body identification number;
(iii)the activities for which they have been notified;
(iv)any restrictions on those activities.
(2) The Secretary of State must ensure that the register referred to in paragraph (1) is maintained and made publicly available.
(3) The Secretary of State may authorise the United Kingdom Accreditation Service to compile and maintain the register in accordance with paragraph (1)(b).]
Textual Amendments