- Y Diweddaraf sydd Ar Gael (Diwygiedig)
- Gwreiddiol (Fel y’i mabwysiadwyd gan yr UE)
Council Directive 96/53/EC of 25 July 1996 laying down for certain road vehicles circulating within the Community the maximum authorized dimensions in national and international traffic and the maximum authorized weights in international traffic
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Mae unrhyw newidiadau sydd wedi cael eu gwneud yn barod gan y tîm yn ymddangos yn y cynnwys a chyfeirir atynt gydag anodiadau.Ar ôl y diwrnod ymadael bydd tair fersiwn o’r ddeddfwriaeth yma i’w gwirio at ddibenion gwahanol. Y fersiwn legislation.gov.uk yw’r fersiwn sy’n weithredol yn y Deyrnas Unedig. Y Fersiwn UE sydd ar EUR-lex ar hyn o bryd yw’r fersiwn sy’n weithredol yn yr UE h.y. efallai y bydd arnoch angen y fersiwn hon os byddwch yn gweithredu busnes yn yr UE. EUR-Lex Y fersiwn yn yr archif ar y we yw’r fersiwn swyddogol o’r ddeddfwriaeth fel yr oedd ar y diwrnod ymadael cyn cael ei chyhoeddi ar legislation.gov.uk ac unrhyw newidiadau ac effeithiau a weithredwyd yn y Deyrnas Unedig wedyn. Mae’r archif ar y we hefyd yn cynnwys cyfraith achos a ffurfiau mewn ieithoedd eraill o EUR-Lex. The EU Exit Web Archive legislation_originated_from_EU_p3
EU Directives are published on this site to aid cross referencing from UK legislation. Since IP completion day (31 December 2020 11.00 p.m.) no amendments have been applied to this version.
1.This Directive applies to:
[F1(a) the dimensions of motor vehicles in categories M2 and M3 and their trailers in category 0 and motor vehicles in categories N2 and N3 and their trailers in categories 03 and 04, as defined in Annex II to Directive 2007/46/EC of the European Parliament and of the Council (1) ;]
(b)the weights and certain other characteristics of the vehicles defined in (a) and specified in Annex I (2) to this Directive.
2.All the values of weights indicated in Annex I are valid as circulation standards and thus refer to loading conditions, not production standards, which will be defined in a later Directive.
[F23. This Directive shall not apply to articulated buses comprising more than one articulated section.]
Textual Amendments
F1 Substituted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
F2 Inserted by Directive 2002/7/EC of the European Parliament and of the Council of 18 February 2002 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic.
For the purposes of this Directive:
‘motor vehicle’ shall mean any power-driven vehicle which travels on the road by its own means,
‘trailer’ shall mean any vehicle intended to be coupled to a motor vehicle excluding semi-trailers, and constructed and equipped for the carriage of goods,
‘semi-trailer’ shall mean any vehicle intended to be coupled to a motor vehicle in such a way that part of it rests on the motor vehicle with a substantial part of its weight and of the weight of its load being borne by the motor vehicle, and constructed and equipped for the carriage of goods,
‘vehicle combination’ shall mean either:
a road train consisting of a motor vehicle coupled to a trailer; or
an articulated vehicle consisting of a motor vehicle coupled to a semi-trailer,
‘conditoned vehicle’ shall mean any vehicle whose fixed or movable superstructures are specially equipped for the carriage of goods at controlled temperatures and whose side walls, inclusive of insulation, are each at least 45 mm thick,
‘bus’ shall mean a vehicle with more than nine seats including the driver's seat, constructed and equipped to carry passengers and their luggage. It may have one or two decks and may also draw a luggage trailer,
‘articulated bus’ shall mean a bus consisting of two rigid sections connected to each other by an articulated section. On this type of vehicle the passenger compartments in each of the two rigid sections shall be intercommunicating. The articulated section shall permit the free movement of travellers between the rigid sections. Connection and disconnection of the two sections shall be possible only in a workshop,
‘maximum authorized dimensions’ shall mean the maximum dimensions for use of a vehicle, as laid down in Annex I to this Directive,
‘maximum authorized weight’ shall mean the maximum weight for use of a laden vehicle in international traffic,
‘maximum authorized axle weight’ shall mean the maximum weight for use in international traffic of a laden axle or group of axles,
‘indivisible load’ shall mean a load that cannot, for the purpose of carriage by road, be divided into two or more loads without undue expense or risk of damage and which owing to its dimensions or mass cannot be carried by a motor vehicle, trailer, road train or articulated vehicle complying with this Directive in all respects,
‘tonne’ shall mean the weight executed by the mass of a tonne and shall correspond to 9,8 kilonewtons (kN),
[F3‘ alternative fuels ’ shall mean fuels or power sources which serve, at least partly, as a substitute for fossil oil sources in the energy supply to transport and which have the potential to contribute to its decarbonisation and enhance the environmental performance of the transport sector, consisting of:
electricity consumed in all types of electric vehicles;
hydrogen;
natural gas, including biomethane, in gaseous form (Compressed Natural Gas — CNG) and liquefied form (Liquefied Natural Gas — LNG);
Liquefied Petroleum Gas (LPG);
mechanical energy from on-board storage/on-board sources, including waste heat,
‘ alternatively fuelled vehicle ’ shall mean a motor vehicle powered wholly or in part by an alternative fuel and which has been approved under the framework of Directive 2007/46/EC,
‘ [F4zero-emission vehicle ’ shall mean a zero-emission heavy-duty vehicle as defined in point (11) of Article 3 of Regulation (EU) 2019/1242 of the European Parliament and of the Council (2) ,]
‘ intermodal transport operation ’ shall mean:
the combined transport operations defined in Article 1 of Council Directive 92/106/EEC (3) engaged in the transport of one or more containers or swap bodies, up to a total maximum length of 45 feet; or
transport operations engaged in the transport of one or more containers or swap bodies, up to a total maximum length of 45 feet, using waterborne transport, provided that the length of the initial or the final road leg does not exceed 150 km in the territory of the Union. The distance of 150 km referred to above may be exceeded in order to reach the nearest suitable transport terminal for the envisaged service in the case of:
vehicles complying with point 2.2.2(a) or (b) of Annex I; or
vehicles complying with point 2.2.2(c) or (d) of Annex I, in cases where such distances are permitted in the relevant Member State.
For intermodal transport operations, the nearest suitable transport terminal providing a service may be located in a Member State other than the Member State in which the shipment was loaded or unloaded,
‘ shipper ’ shall mean a legal entity or a natural or legal person who is named on the bill of lading or on an equivalent transport document, such as a ‘ through ’ bill of lading, as the shipper and/or in whose name or on whose behalf a contract of carriage has been concluded with the transport company.]
All maximum authorized dimensions specified in Annex I shall be measured in accordance with Annex I to [F1Directive 2007/46/EC], with no positive tolerances.
Textual Amendments
F1 Substituted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
F4 Inserted by Regulation (EU) 2019/1242 of the European Parliament and of the Council of 20 June 2019 setting CO2 emission performance standards for new heavy-duty vehicles and amending Regulations (EC) No 595/2009 and (EU) 2018/956 of the European Parliament and of the Council and Council Directive 96/53/EC (Text with EEA relevance).
1.A Member State may not reject or prohibit the use in its territory:
in international traffic, of vehicles registered or put into circulation in any other Member State for reasons relating to their weights and dimensions,
[F5in national traffic, of vehicles registered or put into circulation in any other Member State for reasons relating to their dimensions,]
provided that such vehicles comply with the limit values specified in Annex I.
This provision shall apply notwithstanding the fact that:
(a)the said vehicles are not in conformity with the requirements of that Member State with regard to certain weight and dimension characteristics not covered by Annex I;
(b)the competent authority of the Member State in which the vehicles are registered or put into circulation has authorized limits not referred to in Article 4 (1) exceeding those laid down in Annex I.
2.However, paragraph 1 (a) shall not affect the right of Member States, with due regard to Community law, to require vehicles registered or put into circulation in their own territory to be in conformity with their national requirements on weight and dimension characteristics not covered by Annex I.
3.Member States may require conditioned vehicles to carry an ATP certificate or ATP certification plate provided for in the Agreement of 1 September 1970 on the international carriage of perishable foodstuffs and on the special equipment to be used for such carriage.
Textual Amendments
F5 Substituted by Directive 2002/7/EC of the European Parliament and of the Council of 18 February 2002 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic.
[F51. Member States shall not authorise the normal circulation within their territories:
(a) of vehicles or vehicle combinations for the national transport of goods which are not in conformity with the characteristics set out in points 1.1, 1.2, 1.4, 1.5, 1.6, 1.7, 1.8, 4.2 and 4.4 of Annex I;
(b) of vehicles for national passenger transport, which are not in conformity with the characteristics set out in points 1.1, 1.2, 1.4a, 1.5 and 1.5a of Annex I.
2. Member States may nonetheless authorise the circulation within their territories:
(a) of vehicles or vehicle combinations for the national transport of goods which are not in conformity with the characteristics set out in points 1.3, 2, 3, 4.1 and 4.3 of Annex I;
(b) of vehicles for national passenger transport, which are not in conformity with the characteristics set out in points 1.3, 2, 3, 4.1 and 4.3 of Annex I.]
3.Vehicles or vehicle combinations which exceed the maximum dimensions may only be allowed to circulate on the basis of special permits issued without discrimination by the competent authorities, or on the basis of similar non-discriminatory arrangements agreed on a case-by-case basis with those authorities, where these vehicles or vehicle combinations carry or are intended to carry indivisible loads.
4.Member States may allow [F5vehicles or vehicle combinations used for transport which] carry out certain national transport operations that do not significantly affect international competition in the transport sector to circulate in their territory with dimensions deviating from those laid down in points 1.1, 1.2, 1.4 to 1.8, 4.2 and 4.4 of Annex I.
Transport operations shall be considered not significantly to affect international competition in the transport sector if one of the conditions under (a) and (b) is fulfilled:
(a)the transport operations are carried out in a Member State's territory by specialized vehicles or specialized vehicle combinations in circumstances in which they are not normally carried out by vehicles from other Member States, e.g. operations linked to logging and the forestry industry;
(b)the Member State which permits transport operations to be carried out in its territory by vehicles or vehicle combinations with dimensions deviating from those laid down in Annex I also permits motor vehicles, trailers and semi-trailers which comply with the dimensions laid down in Annex I to be used in such combinations as to achieve at least the loading length authorized in that Member State, so that every operator may benefit from equal conditions of competition (modular concept).
[ F6. . . . .
F6. . . . .]
5.Member States may allow vehicles or vehicle combinations incorporating new technologies or new concepts which cannot comply with one or more requirements of this Directive to carry out certain local transport operations for a trial period. Member States shall inform the Commission thereof.
F66.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
[F27. Until 31 December 2020 Member States may authorise buses that were registered or put into circulation before the implementation of this Directive but the dimensions of which exceed those laid down in points 1.1, 1.2, 1.5 and 1.5a of Annex I to circulate within their territories.]
Textual Amendments
F2 Inserted by Directive 2002/7/EC of the European Parliament and of the Council of 18 February 2002 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic.
F5 Substituted by Directive 2002/7/EC of the European Parliament and of the Council of 18 February 2002 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic.
F6 Deleted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
Articulated vehicles put into circulation before 1 January 1991 which do not comply with the specifications contained in points 1.6 and 4.4 of Annex I shall be deemed to comply with such specifications for the purposes of Article 3 if they do not exceed a total length of 15,50 m.]
Textual Amendments
F1 Substituted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
1.Member States shall take the necessary measures to ensure that Article 1 vehicles referred to in Article 1 and complying with this Directive carry one of the proofs referred to in (a), (b) and (c):
(a)a combination of the following two plates:
(a)the ‘manufacturer's plate’ established and attached in accordance with Directive 76/114/EEC(4),
the plate relating to dimensions, in accordance with Annex III, established and attached in accordance with Directive 76/114/EEC;
(b)a single plate established and attached in accordance with Directive 76/114/EEC and containing the information on the two plates referred to in (a);
(c)a single document issued by the competent authorities of the Member State in which the vehicle is registered or put into circulation. Such document shall bear the same headings and information as the plates referred to in (a). It shall be kept in a place easily accessible to inspection and shall be adequately protected.
2.If the characteristics of the vehicle no longer correspond to those indicated on the proof of compliance, the Member State in which the vehicle is registered shall take the necessary steps to ensure that the proof of compliance is altered.
3.The plates and documents referred to in paragraph 1 shall be recognized by the Member States as the proof of vehicle compliance provided for in this Directive.
4.Vehicles carrying proof of compliance may be subject:
as regards common standards on weights, to random checks,
as regards common standards on dimensions, only to checks where there is a suspicion of non-compliance with this Directive.
5.The middle column of the proof of compliance relating to weights shall contain, where appropriate, the Community weight standards applicable to the vehicle in question. As regards vehicles referred to in point 2.2.2 (c) of Annex I, the entry ‘44 tonnes’ shall be included in brackets under the maximum authorized weight of the vehicle combination.
6.Each Member State may decide, in respect of any vehicle registered or put into circulation in its territory, that the maximum weights authorized by its national legislation shall be indicated in the proof of compliance in the left-hand column and the technically permissible weights in the right-hand column.
This Directive shall not preclude the application of road traffic provisions in force in each Member State which permit the weight and/or dimensions of vehicles on certain roads or civil engineering structures to be limited, irrespective of the State of registration of such vehicles or the State where such vehicles were put into circulation.
This includes the possibility to impose local restrictions on maximum authorised dimensions and/or weights of vehicles that may be used in specified areas or on specified roads, where the infrastructure is not suitable for long and heavy vehicles, such as city centres, small villages or places of special natural interest.]
Textual Amendments
F5 Substituted by Directive 2002/7/EC of the European Parliament and of the Council of 18 February 2002 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Textual Amendments
F6 Deleted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Textual Amendments
F6 Deleted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
1. With the aim of improving their energy efficiency, vehicles or vehicle combinations which are equipped with aerodynamic devices meeting the requirements laid down in paragraphs 2 and 3, and which comply with Directive 2007/46/EC, may exceed the maximum lengths provided for in point 1.1 of Annex I to this Directive, to allow the addition of such devices to the rear of vehicles or vehicle combinations. Vehicles or vehicle combinations equipped with such devices shall comply with point 1.5 of Annex I to this Directive, and any exceeding of the maximum lengths shall not result in an increase in the loading length of those vehicles or vehicle combinations.
2. Before being placed on the market, the aerodynamic devices referred to in paragraph 1 exceeding 500 mm in length shall be type-approved in accordance with the rules on type-approval within the framework of Directive 2007/46/EC.
By 27 May 2017 , the Commission shall assess the need to adopt or amend any technical requirements for type-approval of aerodynamic devices laid down within that framework taking into account the need to ensure road safety and the safety of intermodal transport operations, and in particular:
(a) the secure attachment of the devices in such a way as to reduce the risk of their becoming detached over time, including during an intermodal transport operation;
(b) the safety of other road users, especially vulnerable road users, by ensuring, inter alia, the visibility of contour markings when aerodynamic devices are fitted, by adapting the indirect vision requirements and, in the event of a collision with the rear of a vehicle or a vehicle combination, by not compromising rear underrun protection.
To that end, the Commission shall submit, as appropriate, a legislative proposal to amend the relevant rules on type-approval within the framework of Directive 2007/46/EC.
3. The aerodynamic devices referred to in paragraph 1 shall fulfil the following operational conditions:
(a) in circumstances where the safety of other road users or of the driver is at risk, they shall be folded, retracted or removed by the driver;
(b) their use on urban and inter urban road infrastructures shall take into account the special characteristics of areas where the speed limit is less than or equal to 50 km/h and where vulnerable road users are more likely to be present; and
(c) their use shall be compatible with intermodal transport operations and, in particular, when retracted/folded, they shall not exceed the maximum authorised length by more than 20 cm.
4. The Commission shall adopt implementing acts laying down detailed provisions ensuring uniform conditions for the implementation of paragraph 3. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 10i(2).
5. Paragraph 1 shall apply from the date of transposition or application of the necessary amendments to the instruments referred to in paragraph 2, and after the adoption of the implementing acts referred to in paragraph 4, as appropriate.]
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Textual Amendments
F6 Deleted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
1. With the aim of improving energy efficiency, in particular as regards the aerodynamic performance of cabs, as well as road safety, vehicles or vehicle combinations which fulfil the requirements laid down in paragraph 2 and which comply with Directive 2007/46/EC may exceed the maximum lengths laid down in point 1.1 of Annex I to this Directive provided that their cabs deliver improved aerodynamic performance, energy efficiency and safety performance. Vehicles or vehicle combinations equipped with such cabs shall comply with point 1.5 of Annex I to this Directive and any exceeding of the maximum lengths shall not result in an increase in the load capacity of those vehicles.
2. Before being placed on the market, the vehicles referred to in paragraph 1 shall be approved in accordance with the rules on type-approval within the framework of Directive 2007/46/EC. By 27 May 2017 , the Commission shall assess the need to develop the technical requirements for type-approval of vehicles equipped with such cabs as laid down within that framework, taking into account the following:
(a) the improved aerodynamic performance of vehicles or vehicle combinations;
(b) vulnerable road users, and improvement of their visibility to drivers, in particular by reducing drivers' blind spots;
(c) the reduction in damage or injury caused to other road users in the event of a collision;
(d) the safety and comfort of drivers.
[F7To that end, the Commission shall take the measures necessary, within the framework of Directive 2007/46/EC, to provide for the type-approval of vehicles or vehicle combinations referred to in paragraph 1 of this Article by 1 November 2019 .]
[F73. Paragraph 1 shall apply from 1 September 2020 .] ]
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
F7 Substituted by Decision (EU) 2019/984 of the European Parliament and of the Council of 5 June 2019 amending Council Directive 96/53/EC as regards the time limit for the implementation of the special rules regarding maximum length for cabs delivering improved aerodynamic performance, energy efficiency and safety performance.
The Directive listed in Annex IV, Part A, shall be repealed with effect from the date in Article 11, without prejudice to the obligations of the Member States concerning the deadlines for transposition set out in Annex IV, Part B.
References to the repealed Directives shall be construed as references to this Directive and shall be read in accordance with the correlation table set out in Annex V.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Textual Amendments
F6 Deleted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
The maximum authorised weights of alternatively fuelled or zero-emission vehicles shall be those set out in points 2.2.1, 2.2.2, 2.2.3, 2.2.4, 2.3.1, 2.3.2 and 2.4 of Annex I.
Alternatively fuelled or zero-emission vehicles shall also comply with the maximum authorised axle weight limits set out in point 3 of Annex I.
The additional weight required by alternatively fuelled or zero-emission vehicles shall be defined on the basis of the documentation provided by the manufacturer when the vehicle in question is approved. That additional weight shall be indicated in the official proof required in accordance with Article 6.
The Commission shall be empowered to adopt delegated acts in accordance with Article 10h to update, for the purposes of this Directive, the list of alternative fuels referred to in Article 2 that require additional weight. It is of particular importance that the Commission follow its usual practice and carry out consultations with experts, including Member States’ experts, before adopting those delegated acts.]
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
F8 Substituted by Regulation (EU) 2019/1242 of the European Parliament and of the Council of 20 June 2019 setting CO2 emission performance standards for new heavy-duty vehicles and amending Regulations (EC) No 595/2009 and (EU) 2018/956 of the European Parliament and of the Council and Council Directive 96/53/EC (Text with EEA relevance).
The maximum lengths laid down in point 1.1 of Annex I, subject where applicable to Article 9a(1), and the maximum distance laid down in point 1.6 of Annex I, may be exceeded by 15 cm for vehicles or vehicle combinations engaged in the transport of 45-foot containers or 45-foot swap bodies, empty or loaded, provided that the road transport of the container or swap body in question is part of an intermodal transport operation.
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
1. By 27 May 2021 , Member States shall take specific measures to identify vehicles or vehicle combinations in circulation that are likely to have exceeded the maximum authorised weight and that should therefore be checked by their competent authorities in order to ensure compliance with the requirements of this Directive. Those measures may be taken with the aid of automatic systems set up on the road infrastructure, or by means of on-board weighing equipment installed in vehicles in accordance with paragraph 4.
A Member State shall not require on-board weighing equipment to be installed on vehicles or vehicle combinations which are registered in another Member State.
Without prejudice to Union and national law, where automatic systems are used to establish infringements of this Directive and to impose penalties, such automatic systems shall be certified. Where automatic systems are used only for identification purposes, they need not be certified.
2. Each Member State shall carry out each calendar year an appropriate number of checks on the weight of vehicles or vehicle combinations in circulation, proportionate to the total number of vehicles inspected each year in its territory.
3. Member States shall, in accordance with Article 18 of Regulation (EC) No 1071/2009 of the European Parliament and of the Council (5) , ensure that their competent authorities exchange information about infringements and penalties relating to this Article.
4. The on-board weighing equipment referred to in paragraph 1 shall be accurate and reliable, fully interoperable and compatible with all vehicle types.
5. By 27 May 2016 , the Commission shall adopt implementing acts, laying down detailed provisions ensuring uniform conditions for the implementation of the rules on interoperability and compatibility set out in paragraph 4.
In order to ensure interoperability, those detailed provisions shall enable the weight data to be communicated at any time from a moving vehicle to the competent authorities, as well as to its driver. That communication shall be done through the interface defined by the CEN DSRC standards EN 12253, EN 12795, EN 12834, EN 13372 and ISO 14906. In addition, such communication shall ensure that the competent authorities of the Member States can communicate and exchange information in the same way with vehicles and vehicle combinations registered in any Member State and using on-board weighing equipment.
In order to ensure compatibility with all vehicle types, on-board systems of motor vehicles shall have the capability to receive and process any data coming from any type of trailer or semi-trailer attached to the motor vehicle.
Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 10i(2).
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
Member States shall lay down rules on penalties applicable to infringements of this Directive and shall take all measures necessary to ensure that they are implemented. Those penalties shall be effective, non-discriminatory, proportionate and dissuasive. Member States shall notify those rules to the Commission.
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
1. For the transport of containers and swap bodies, Member States shall lay down rules that require:
(a) the shipper to give to the haulier to whom it entrusts the transport of a container or swap body a statement indicating the weight of the container or swap body transported; and
(b) the haulier to provide access to all relevant documentation provided by the shipper.
2. Member States shall lay down rules on the liability of both the shipper and the haulier as appropriate in cases where the information referred to in paragraph 1 is missing or is incorrect and the vehicle or vehicle combination is overloaded.
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
Every 2 years, and at the latest by 30 September of the year following the end of the 2-year period concerned, Member States shall send to the Commission the necessary information concerning:
the number of checks carried out in the previous 2 calendar years; and
the number of overloaded vehicles or vehicle combinations detected.
This information may be part of the information submitted under Article 17 of Regulation (EC) No 561/2006 of the European Parliament and of the Council (6) .
The Commission shall analyse the information received pursuant to this Article, and shall include such analysis in the report to be forwarded to the European Parliament and to the Council pursuant to Regulation (EC) No 561/2006.
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
1. The power to adopt delegated acts is conferred on the Commission subject to the conditions laid down in this Article.
2. The power to adopt delegated acts referred to in Article 10b shall be conferred on the Commission for a period of 5 years from 26 May 2015 . The Commission shall draw up a report in respect of the delegation of power not later than 9 months before the end of the 5-year period. The delegation of power shall be tacitly extended for periods of an identical duration, unless the European Parliament or the Council opposes such extension not later than 3 months before the end of each period.
3. The delegation of power referred to in Article 10b may be revoked at any time by the European Parliament or by the Council. A decision to revoke shall put an end to the delegation of the power specified in that decision. It shall take effect the day following the publication of the decision in the Official Journal of the European Union or at a later date specified therein. It shall not affect the validity of any delegated acts already in force.
4. As soon as it adopts a delegated act, the Commission shall notify it simultaneously to the European Parliament and to the Council.
5. A delegated act adopted pursuant to Article 10b shall enter into force only if no objection has been expressed either by the European Parliament or the Council within a period of 2 months of notification of that act to the European Parliament and the Council or if, before the expiry of that period, the European Parliament and the Council have both informed the Commission that they will not object. That period shall be extended by 2 months at the initiative of the European Parliament or of the Council.
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
1. The Commission shall be assisted by the Road Transport Committee referred to in Article 42 of Regulation (EU) No 165/2014 of the European Parliament and of the Council (7) . That committee shall be a committee within the meaning of Regulation (EU) No 182/2011 of the European Parliament and of the Council (8) .
2. Where reference is made to this paragraph, Article 5 of Regulation (EU) No 182/2011 shall apply.
3. Where the committee delivers no opinion, the Commission shall not adopt the draft implementing act and the third subparagraph of Article 5(4) of Regulation (EU) No 182/2011 shall apply.
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
By 8 May 2020 , the Commission shall submit, as appropriate, a report to the European Parliament and the Council on the implementation of the amendments to this Directive introduced by Directive (EU) 2015/719 of the European Parliament and of the Council (9) , including taking into consideration specific characteristics of certain market segments. On the basis of that report, the Commission shall, if appropriate, make a legislative proposal duly accompanied by an impact assessment. The report shall be made available at least 6 months prior to the submission of any legislative proposal.]
Textual Amendments
F3 Inserted by Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic (Text with EEA relevance).
1.Member States shall bring into force the laws, regulations and administrative provisions necessary to comply with this Directive by 17 September 1997. They shall forthwith inform the Commission thereof.
When Member States adopt these measures, they shall contain a reference to this Directive or shall be accompanied by such reference on the occasion of their official publication. The methods of making such reference shall be laid down by Member States.
2.Member States shall communicate to the Commission the text of the main provisions of domestic law which they adopt in the field covered by this Directive.
This Directive shall enter into force on the day of its publication in the Official Journal of the European Communities
This Directive is addressed to the Member States.
Y Diweddaraf sydd Ar Gael (diwygiedig):Y fersiwn ddiweddaraf sydd ar gael o’r ddeddfwriaeth yn cynnwys newidiadau a wnaed gan ddeddfwriaeth ddilynol ac wedi eu gweithredu gan ein tîm golygyddol. Gellir gweld y newidiadau nad ydym wedi eu gweithredu i’r testun eto yn yr ardal ‘Newidiadau i Ddeddfwriaeth’.
Gwreiddiol (Fel y’i mabwysiadwyd gan yr UE): Mae'r wreiddiol version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Rhychwant ddaearyddol: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Dangos Llinell Amser Newidiadau: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Gallwch wneud defnydd o ddogfennau atodol hanfodol a gwybodaeth ar gyfer yr eitem ddeddfwriaeth o’r tab hwn. Yn ddibynnol ar yr eitem ddeddfwriaeth sydd i’w gweld, gallai hyn gynnwys:
Mae’r llinell amser yma yn dangos y fersiynau gwahanol a gymerwyd o EUR-Lex yn ogystal ag unrhyw fersiynau dilynol a grëwyd ar ôl y diwrnod ymadael o ganlyniad i newidiadau a wnaed gan ddeddfwriaeth y Deyrnas Unedig.
Cymerir dyddiadau fersiynau’r UE o ddyddiadau’r dogfennau ar EUR-Lex ac efallai na fyddant yn cyfateb â’r adeg pan ddaeth y newidiadau i rym ar gyfer y ddogfen.
Ar gyfer unrhyw fersiynau a grëwyd ar ôl y diwrnod ymadael o ganlyniad i newidiadau a wnaed gan ddeddfwriaeth y Deyrnas Unedig, bydd y dyddiad yn cyd-fynd â’r dyddiad cynharaf y daeth y newid (e.e. ychwanegiad, diddymiad neu gyfnewidiad) a weithredwyd i rym. Am ragor o wybodaeth gweler ein canllaw i ddeddfwriaeth ddiwygiedig ar Ddeall Deddfwriaeth.
Defnyddiwch y ddewislen hon i agor dogfennau hanfodol sy’n cyd-fynd â’r ddeddfwriaeth a gwybodaeth am yr eitem hon o ddeddfwriaeth. Gan ddibynnu ar yr eitem o ddeddfwriaeth sy’n cael ei gweld gall hyn gynnwys:
liciwch ‘Gweld Mwy’ neu ddewis ‘Rhagor o Adnoddau’ am wybodaeth ychwanegol gan gynnwys