Commission Regulation (EU) No 1301/2014Dangos y teitl llawn

1. Introductory Text

2. Article 1. Subject matter

3. Article 2. Scope

4. Article 3. Open points

5. Article 4. Specific cases

6. Article 5. Notification of bilateral agreements

7. Article 6. Projects at an advanced stage of development

8. Article 7. ‘EC’ certificate of verification

9. Article 8. Conformity assessment

10. Article 9. Implementation

11. Article 10. Innovative solutions

12. Article 11. Repeal

13. Article 12. Entry into force

14. Signature

15. 1. ANNEX

       1. 1. INTRODUCTION

          1. 1.1. Technical Scope

          2. 1.2. Geographical scope

          3. 1.3. Content of this TSI

       2. 2. DESCRIPTION OF THE ENERGY SUBSYSTEM

          1. 2.1. Definition

             1. 2.1.1. Power supply

             2. 2.1.2. Geometry of the overhead contact line (OCL) and quality of...

          2. 2.2. Interfaces with other subsystems

             1. 2.2.1. Introduction

             2. 2.2.2. Interfaces of this TSI with the Safety in railway tunnels...

       3. 3. ESSENTIAL REQUIREMENTS

       4. 4. CHARACTERISATION OF THE SUBSYSTEM

          1. 4.1. Introduction

          2. 4.2. Functional and technical specifications of the subsystem

             1. 4.2.1. General provisions

             2. 4.2.2. Basic parameters characterising the energy subsystem

             3. 4.2.3. Voltage and frequency

             4. 4.2.4. Parameters relating to supply system performance

                1. 4.2.4.1. Maximum train current

                2. 4.2.4.2. Mean useful voltage

             5. 4.2.5. Current at standstill (DC systems only)

             6. 4.2.6. Regenerative braking

             7. 4.2.7. Electrical protection coordination arrangements

             8. 4.2.8. Harmonics and dynamic effects for AC traction power supply systems...

             9. 4.2.9. Geometry of the overhead contact line

                1. 4.2.9.1. Contact wire height

                2. 4.2.9.2. Maximum lateral deviation

             10. 4.2.10. Pantograph gauge

             11. 4.2.11. Mean contact force

             12. 4.2.12. Dynamic behaviour and quality of current collection

             13. 4.2.13. Pantograph spacing for overhead contact line design

             14. 4.2.14. Contact wire material

             15. 4.2.15. Phase separation sections

                 1. 4.2.15.1. General

                 2. 4.2.15.2. Lines with speed v ≥ 250 km/h

                 3. 4.2.15.3. Lines with speed v < 250 km/h

             16. 4.2.16. System separation sections

                 1. 4.2.16.1. General

                 2. 4.2.16.2. Pantographs raised

                 3. 4.2.16.3. Pantographs lowered

             17. 4.2.17. On-ground energy data collecting system

                 1. (1) Point 4.2.8.2.8 of LOC & PAS TSI contains the requirements...

                 2. (2) The on-ground energy data collecting system (DCS) shall receive, store...

                 3. (3) The on-ground energy DCS shall support all the data exchange...

             18. 4.2.18. Protective provisions against electric shock

          3. 4.3. Functional and technical specifications of the interfaces

             1. 4.3.1. General requirements

             2. 4.3.2. Interface with Rolling Stock subsystem.

             3. 4.3.3. Interface with Infrastructure subsystem

             4. 4.3.4. Interface with Control — Command and Signalling subsystems

             5. 4.3.5. Interface with Operation and traffic management subsystem

          4. 4.4. Operating rules

          5. 4.5. Maintenance rules

          6. 4.6. Professional qualifications

          7. 4.7. Health and safety conditions

       5. 5. INTEROPERABILITY CONSTITUENTS

          1. 5.1. List of constituents

          2. 5.2. Constituents' performances and specifications

             1. 5.2.1. Overhead contact line

                1. 5.2.1.1. Geometry of the OCL

                2. 5.2.1.2. Mean contact force

                3. 5.2.1.3. Dynamic behaviour

                4. 5.2.1.4. Space for steady arm uplift

                5. 5.2.1.5. Pantograph spacing for overhead contact line design

                6. 5.2.1.6. Current at standstill (DC systems only)

                7. 5.2.1.7. Contact wire material

       6. 6. ASSESSMENT OF CONFORMITY OF THE INTEROPERABILITY CONSTITUENTS AND EC VERIFICATION...

          1. 6.1. Interoperability constituents

             1. 6.1.1. Conformity assessment procedures

             2. 6.1.2. Application of modules

             3. 6.1.3. Innovative solutions for interoperability constituents

             4. 6.1.4. Particular assessment procedure for the interoperability constituent — overhead contact...

                1. 6.1.4.1. Assessment of dynamic behaviour and quality of current collection

                2. 6.1.4.2. Assessment of current at standstill (DC systems only)

             5. 6.1.5. EC declaration of conformity of interoperability constituent OCL

          2. 6.2. Energy subsystem

             1. 6.2.1. General provisions

             2. 6.2.2. Application of modules

                1. 6.2.2.1. Application of module SG

                2. 6.2.2.2. Application of module SH1

             3. 6.2.3. Innovative solutions

             4. 6.2.4. Particular assessment procedures for energy subsystem

                1. 6.2.4.1. Assessment of mean useful voltage

                2. 6.2.4.2. Assessment of regenerative braking

                3. 6.2.4.3. Assessment of electrical protection coordination arrangements

                4. 6.2.4.4. Assessment of harmonics and dynamic effects for AC traction power...

                5. 6.2.4.5. Assessment of dynamic behaviour and quality of current collection (integration...

                6. 6.2.4.6. Assessment of the protective provisions against electric shock

                7. 6.2.4.7. Assessment of maintenance plan

          3. 6.3. Sub-system containing interoperability constituents not holding an EC declaration

             1. 6.3.1. Conditions

             2. 6.3.2. Documentation

             3. 6.3.3. Maintenance of the subsystems certified according to 6.3.1

       7. 7. IMPLEMENTATION OF THE ENERGY TSI

          1. 7.1. Application of this TSI to railway lines

          2. 7.2. Application of this TSI to new, renewed or upgraded railway...

             1. 7.2.1. Introduction

             2. 7.2.2. Implementation plan for voltage and frequency

             3. 7.2.3. Implementation plan for OCL geometry

                1. 7.2.3.1. Scope of the implementation plan

                2. 7.2.3.2. Implementation rules for 1 435 mm track gauge system

                3. 7.2.3.3. Track gauge systems different than 1 435mm

             4. 7.2.4. By 1 January 2022 , Member States shall ensure that an...

          3. 7.3. Application of this TSI to existing lines

             1. 7.3.1. Introduction

             2. 7.3.2. Upgrading/renewal of the OCL and/or the power supply

             3. 7.3.3. Parameters related to maintenance

             4. 7.3.4. The procedure to be used for the demonstration of the...

             5. 7.3.5. Route compatibility checks before the use of authorised vehicles

          4. 7.4. Specific cases

             1. 7.4.1. General

                1. (1) The specific cases, as listed in point 7.4.2, describe special...

                2. (2) These specific cases are classified as:

             2. 7.4.2. List of specific cases

                1. 7.4.2.1. Particular features on the Estonian network

                   1. 7.4.2.1.1. Voltage and frequency (4.2.3)

                      1. P case

                2. 7.4.2.2. Particular features on the French network

                   1. 7.4.2.2.1. Voltage and frequency (4.2.3)

                      1. T case

                   2. 7.4.2.2.2. Phase separation sections — lines with speed v ≥ 250...

                      1. P case

                3. 7.4.2.3. Particular features on the Italian network

                   1. 7.4.2.3.1. Phase separation sections — lines with speed v ≥ 250...

                      1. P case

                4. 7.4.2.4. Particular features on the Latvian network

                   1. 7.4.2.4.1. Voltage and frequency (4.2.3)

                      1. P case

                5. 7.4.2.5. Particular features on the Lithuanian network

                   1. 7.4.2.5.1. Dynamic behaviour and quality of current collection (4.2.12)

                      1. P case

                6. 7.4.2.6. Particular features on the Polish network

                   1. 7.4.2.6.1. Electrical protection coordination arrangements (4.2.7)

                      1. P case

                7. 7.4.2.7. Particular features on the Spanish network

                   1. 7.4.2.7.1. Contact wire height (4.2.9.1)

                      1. P case

                   2. 7.4.2.7.2. Phase separation sections — lines with speed v ≥ 250...

                      1. P case

                8. 7.4.2.8. Particular features on the Swedish network

                   1. 7.4.2.8.1. Assessment of mean useful voltage (6.2.4.1)

                      1. P case

                9. 7.4.2.9. Particular features on the UK network for Great Britain

                   1. 7.4.2.9.1. Voltage and frequency (4.2.3)

                      1. P case

                   2. 7.4.2.9.2. Contact wire height (4.2.9.1)

                      1. P case

                   3. 7.4.2.9.3. Maximum lateral deviation (4.2.9.2) and pantograph gauge (4.2.10)

                      1. P case

                   4. 7.4.2.9.4. Protective provisions against electric shock (4.2.18)

                      1. P case

                   5. 7.4.2.9.5. Conformity assessment of OCL as component

                      1. P case

                10. 7.4.2.10. Particular features on the Eurotunnel network

                    1. 7.4.2.10.1. Contact wire height (4.2.9.1)

                       1. P case

                11. 7.4.2.11. Particular features on the Luxembourgish network

                    1. 7.4.2.11.1. Voltage and frequency (4.2.3)

                       1. T case

       8. Appendix A

          Conformity assessment of interoperability constituents

          1. A.1 SCOPE

          2. A.2 CHARACTERISTICS

       9. Appendix B

          EC verification of the energy subsystem

          1. B.1 SCOPE

          2. B.2 CHARACTERISTICS

       10. Appendix C

           Mean useful voltage

           1. C.1 VALUES FOR U MEAN USEFUL AT THE PANTOGRAPH

           2. C.2 SIMULATION RULES

       11. Appendix D

           Specification of the pantograph gauge

           1. D.1 SPECIFICATION OF THE MECHANICAL KINEMATIC PANTOGRAPH GAUGE

              1. D.1.1 General

                 1. D.1.1.1 Space to be cleared for electrified lines

                 2. D.1.1.2 Particularities

                 3. D.1.1.3 Symbols and abbreviations

                 4. D.1.1.4 Basic principles

                    1. Figure D.1 Pantograph mechanical gauges

                       1. Caption:

              2. D.1.2 Specification of the mechanical kinematic pantograph gauge

                 1. D.1.2.1 Specification of the width of the mechanical gauge

                    1. D.1.2.1.1 Scope

                    2. D.1.2.1.2 Calculation methodology

                    3. D.1.2.1.3 Half-length bw of the pantograph bow

                    4. D.1.2.1.4 Pantograph sway ep

                    5. D.1.2.1.5 Additional overthrows

                    6. D.1.2.1.6 Quasi-static effect

                    7. D.1.2.1.7 Allowances

                 2. D.1.2.2 Specification of the height of the mechanical gauge

              3. D.1.3 Reference parameters

              4. D.1.4 Calculation of maximum lateral deviation of contact wire

           2. D.2 SPECIFICATION OF THE STATIC PANTOGRAPH GAUGE (TRACK GAUGE SYSTEM 1...

       12. Appendix E

           List of referenced standards

       13. Appendix F

           List of open points

           1. Intentionally deleted

       14. Appendix G

           Glossary