Commission Regulation (EU) 2017/2400Dangos y teitl llawn

Markings and numbering U.K.

1. Markings U.K.

In the case of a component being certified in accordance with this Annex, the component shall bear:

[F1 1.1. The manufacturer's name or trade mark U.K.

Textual Amendments

F1 Substituted by Commission Regulation (EU) 2019/318 of 19 February 2019 amending Regulation (EU) 2017/2400 and Directive 2007/46/EC of the European Parliament and of the Council as regards the determination of the CO2 emissions and fuel consumption of heavy-duty vehicles (Text with EEA relevance).

1.2. The make and identifying type indication as recorded in the information referred to in point 0.2 and 0.3 of Appendices 2 - 5 to this Annex] U.K.

1.3 The certification mark (if applicable) as a rectangle surrounding the lower-case letter ‘e’ followed by the distinguishing number of the Member State which has granted the certificate: U.K.

• 1 for Germany;

• 2 for France;

• 3 for Italy;

• 4 for the Netherlands;

• 5 for Sweden;

• 6 for Belgium;

• 7 for Hungary;

• 8 for the Czech Republic;

• 9 for Spain;

• 11 for the United Kingdom;

• 12 for Austria;

• 13 for Luxembourg;

• 17 for Finland;

• 18 for Denmark;

• 19 for Romania;

• 20 for Poland;

• 21 for Portugal;

• 23 for Greece;

• 24 for Ireland;

• 25 for Croatia;

• 26 for Slovenia;

• 27 for Slovakia;

• 29 for Estonia;

• 32 for Latvia;

• 34 for Bulgaria;

• 36 for Lithuania;

• 49 for Cyprus;

• 50 for Malta

1.4 The certification mark shall also include in the vicinity of the rectangle the ‘base approval number’ as specified for Section 4 of the type-approval number set out in Annex VII to Directive 2007/46/EC, preceded by the two figures indicating the sequence number assigned to the latest technical amendment to this Regulation and by an alphabetical character indicating the part for which the certificate has been granted. U.K.

For this Regulation, the sequence number shall be 00.

For this Regulation, the alphabetical character shall be the one laid down in Table 1.

Table 1

[F1 G	Transmission]
C	Torque Converter (TC)
O	Other torque transferring component (OTTC)
D	Additional driveline component (ADC)

[F1 1.5. Example of the certification mark U.K.

The above certification mark affixed to a transmission, torque converter (TC), other torque transferring component (OTTC) or additional driveline component (ADC) shows that the type concerned has been certified in Poland (e20), pursuant to this Regulation. The first two digits (00) are indicating the sequence number assigned to the latest technical amendment to this Regulation. The following digit indicates that the certification was granted for a transmission (G). The last four digits (0004) are those allocated by the approval authority to the transmission, as the base approval number.]

1.6 On request of the applicant for certificate and after prior agreement with the approval authority other type sizes than indicated in 1.5 may be used. Those other type sizes shall remain clearly legible. U.K.

1.7 The markings, labels, plates or stickers must be durable for the useful life of the transmission, torque converter (TC), other torque transferring components (OTTC) or additional driveline components (ADC) and must be clearly legible and indelible. The manufacturer shall ensure that the markings, labels, plates or sticker cannot be removed without destroying or defacing them. U.K.

1.8 In the case separate certifications are granted by the same approval authority for a transmission, a torque converter, other torque transferring components or additional driveline components and those parts are installed in combination, the indication of one certification mark referred to in point 1.3 is sufficient. This certification mark shall be followed by the applicable markings specified in point 1.4 for the respective transmission, torque converter, other torque transferring component or additional driveline component separated by ‘/’. U.K.

1.9. The certification mark shall be visible when the transmission, torque converter, other torque transferring component or additional driveline component is installed on the vehicle and shall be affixed to a part necessary for normal operation and not normally requiring replacement during component life. U.K.

1.10 In the case that torque converter or other torque transferring components are constructed in such a way that they are not accessible and / or visible after being assembled with a transmission the certification mark of the torque converter or other torque transferring component shall be placed on the transmission. U.K.

In the case described in first paragraph, if a torque converter or other torque transferring component have not been certified, ‘–’ instead of the certification number shall be indicated on the transmission next to the alphabetical character specified in point 1.4.

2. Numbering U.K.

[F1 2.1. Certification number for transmissions, torque converter, other torque transferring component and additional driveline component shall comprise the following: U.K.

eX*YYYY/YYYY*ZZZZ/ZZZZ*X*0000*00

Section 1	Section 2	Section 3	Additional letter to Section 3	Section 4	Section 5
Indication of country issuing the certificate	HDV CO 2 certification Regulation (2017/2400)	Latest amending Regulation (ZZZZ/ZZZZ)	See Table 1 of this appendix	Base certification number 0000	Extension 00]