The Road Vehicles (Construction and Use) (Amendment) (No. 2) Regulations 1992

PART I GENERAL

Citation and commencement

1.—(1) These Regulations may be cited as the Road Vehicles (Constructionand Use) (Amendment) (No. 2) Regulations 1992.

(2) These Regulations shall come into force for the purposes of regulation 8 on 1st August 1993 and for all other purposes on 1st August 1992.

Preliminary

2.—(1) The Road Vehicles (Construction and Use) Regulations 1986(1) shall be further amended in accordance with the following provisions of these Regulations.

(2) The Secretary of State is satisfied that—

(a) it is requisite that the provisions of regulations 3 to 7 shall apply as from 1st August 1992 and of regulation 8 as from 1st August 1993 (being provisions which vary the requirements as regards the construction of certain classes of vehicles) to vehicles registered under the Vehicles (Excise) Act 1971(2) before the expiration of one year from the making of these Regulations; and

(b) notwithstanding that the said provisions will then apply to those vehicles, no undue hardship or inconvenience will be caused thereby.

PART II AMENDMENTS WHICH COME INTO FORCE ON 1ST AUGUST 1992

Amendments to Regulation 36A (speed limiters for coaches)

3.—(1) Regulation 36A shall be amended as follows.

(2) In paragraph (3)(c), after “be sealed” there shall be inserted “by an authorised sealer”.

(3) After paragraph (3), there shall be inserted the following paragraph—

“(3A) Paragraph (3)(c) shall have effect in relation to—

(a) a speed limiter fitted before 1st August 1992 to a vehicle first used before that date,

(b) a speed limiter sealed outside the United Kingdom, “by an authorised sealer” were omitted”.

(4) In paragraph (5), before the definition of “Part I of the British Standard” there shall be inserted the following definition—

• ““authorised sealer” has the meaning given in Schedule 3B to these Regulations.”

Amendments to Regulation 36B (speed limiters for goods vehicles)

4.—(1) Regulation 36B shall be amended as follows.

(2) In paragraph (3)(c), after “be sealed” there shall be inserted “by an authorised sealer”.

(3) After paragraph (3), there shall be inserted the following paragraph—

“(3A) Paragraph (3)(c) shall have effect in relation to—

(a) a speed limiter fitted before 1st August 1992 to a vehicle first used before that date,

(b) a speed limiter sealed outside the United Kingdom, “by an authorised sealer” were omitted”.

(4) In paragraph (7), before the words “Part I of the British Standard” there shall be inserted the words “authorised sealer”.

Speed limiters — authorised sealers

5.—(1) After Regulation 36B, there shall be inserted the following—

“Speed limiters — authorised sealers

36C.   Schedule 3B (authorised sealers) shall have effect.”

(2) After Schedule 3A there shall be inserted the Schedule set out inthe Schedule to these Regulations.

Amendments to Regulation 70A (speed limiter plates for coaches)

6.—(1) Regulation 70A shall be amended as follows.

(2) In paragraphs (2) and (4) after the word “plate” there shall be inserted “which has been supplied by the authorised sealer who sealed the speedlimiter and”.

(3) After paragraph (4), there shall be inserted the following paragraph—

“(4A) Paragraphs (2) and (4) shall have effect, in relation to a vehicle which is not required to be fitted with a speed limiter which has been sealed by an authorised sealer, as if the words “which has been supplied by the authorised sealer who sealed the speedlimiter and” had been omitted.”.

Amendment to Regulation 70B (speed limiter plates for goods vehicles)

7.—(1) Regulation 70B shall be amended as follows.

(2) In paragraph (1), the words “which complies with” to the end shall be omitted.

(3) In paragraph (2), after the word “plate” there shall be inserted “which has been supplied by the authorised sealer who sealed the speedlimiter and”.

(4) After paragraph (4), there shall be inserted the following paragraph—

“(4A) Paragraph (2) shall have effect, in relation to a vehicle which is not required to be fitted with a speed limiter which has been sealed by an authorised sealer, as if the words “which has been supplied by the authorised sealer who sealed the speedlimiter and” had been omitted.”

PART III AMENDMENTS WHICH COME INTO FORCE ON 1ST AUGUST 1993

Amendment to regulation 36B (speed limiters for goods vehicles)

8.  Regulation 36B shall be amended as follows—

(a) after paragraph (1), there shall be inserted the following paragraph—

“(1A) Subject to paragraph (6), this regulation also applies to every motor vehicle which—

(a) is a goods vehicle;

(b) has a maximum gross weight exceeding 16,000kg;

(c) is either—

(i) a vehicle that is constructed or adapted to form part of an articulated vehicle, or

(ii) a rigid vehicle that is constructed or adapted to draw a trailer and has a maximum gross trailer weight which exceeds 5,000kg;

(d) is first used on or after 1st January 1988; and

(e) has, or if a speed limiter were not fitted to it would have, a relevant speed exceeding 60mph.”; and

(b) after paragraph (7), there shall be inserted the following paragraph—

“(8) For the purposes of this regulation, a motor vehicle has a maximum gross trailer weight exceeding 5,000kg if—

(a) in the case of a vehicle equipped with a Ministry plate in accordance with regulation 70, the difference between its maximum gross weight and the relevant train weight exceeds 5,000kg;

(b) in the case of a vehicle not equipped with a Ministry plate, but which is equipped with a plate in accordance with regulation 66, the difference between its maximum gross weight and the weight shown on the plate in respect of item 8 of Part I of Schedule 8 exceeds 5,000kg; and

(c) in the case of any other vehicle, the vehicle is designed or adapted to be capable of drawing a trailer with a laden weight exceeding 5,000kg when travelling on a road;

• and in sub-paragraph (a) “the relevant train weight” is the train weight shown in column (3) of the plate or, if no such weight is shown, the train weight shown in column (2) of the plate (where the plate is in the form required by Schedule 10) or in column (4) of the plate (where the plate is in the form required by Schedule10A).”

Signed by Authority of the Secretary of State for Transport

Christopher Chope

Parliamentary Under Secretary of State,

Department of Transport

2nd March 1992