The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007

Regulations 2(1) and 16(2)

SCHEDULE 1 E+W+S Conditions for treatment of natural mineral waters and spring waters with ozone–enriched air

1.  Treatment of natural mineral waters and spring waters with ozone-enriched air shall only be carried out if— E+W+S

(a) it is for the purpose of separating compounds of iron, manganese, sulphur and arsenic from water in which they occur naturally at source;

(b) prior to treatment the requirements of paragraphs 3, 4 and 5 of Schedule 4 are satisfied; and

(c) the treatment does not have a disinfectant action.

2.  Treatment of natural mineral waters and spring waters with ozone–enriched air shall not— E+W+S

(a) modify the physico–chemical composition of the water in terms of its characteristic constituents; or

(b) leave residues in the water which could pose a risk to public health, or, in the case of the substances listed below, above the levels specified.

Treatment residue	Maximum limit (µg/l)
Dissolved ozone	50
Bromate	3
Bromoform	1

3.  A person seeking to have a treatment with ozone-enriched air authorised shall— E+W+S

(a) make application in writing to the relevant authority within whose area the water is extracted;

(b) permit representatives of that authority to examine the proposed method of treatment, and place of treatment, and take samples for analysis in accordance with regulation 17; and

(c) provide such information in support of the application as is requested by the relevant authority.

4.  The relevant authority shall assess the application and any information in its possession and shall authorise the treatment if it is satisfied that— E+W+S

(a) the treatment is justified by the composition of the water at source;

(b) the person carrying out the treatment is taking all necessary measures to ensure that the treatment is effective and safe; and

(c) the treatment otherwise complies with paragraphs 1 and 2.

5.  Where the relevant authority decides to authorise a treatment pursuant to paragraph 4, it shall inform the operator of the treatment in writing and state the date from which the authorisation for commercial use of the treatment has effect. E+W+S

6.  Where the relevant authority refuses to authorise a treatment pursuant to paragraph 4, it shall inform the operator of the treatment in writing, stating its reasons. E+W+S

7.  Where a treatment has been authorised pursuant to paragraph 4, the person carrying out the treatment must, for the purpose of enabling the relevant authority to assess whether the conditions in paragraph 4(a) and (b) continue to be satisfied— E+W+S

(a) permit representatives of the authority to examine the method of treatment and place of treatment and take samples for analysis in accordance with regulation 17; and

(b) provide such information related to the treatment as is requested by the authority.

8.  If the relevant authority is satisfied that the conditions specified in paragraph 4 are no longer fulfilled, it may withdraw authorisation of a treatment by giving the person operating that treatment a written notice stating the grounds for withdrawal. E+W+S

9.  Where the relevant authority has informed an operator under paragraph 6 of its refusal to authorise a treatment under paragraph 4 or withdraws authorisation of a treatment under paragraph 8, the person who wishes to carry out the treatment may apply to [F1 the Secretary of State] for a review of that decision. E+W+S

Textual Amendments

F1 Words in Sch. 1 para. 9 substituted (6.4.2011) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2011 (S.I. 2011/451), regs. 1, 2(5)(b) (with regs. 3, 4)

10.  Upon receiving the application for review, [F2 the Secretary of State] shall make such inquiry into the matter as may seem to [F2 the Secretary of State] to be appropriate and, having considered the results of that enquiry and any relevant facts elicited by it, shall either confirm the decision or direct the relevant authority to grant or restore, as appropriate, authorisation of the treatment process in operation. In the case of such a direction the relevant authority shall thereupon comply with the said direction. E+W+S

Textual Amendments

F2 Words in Sch. 1 para. 10 substituted (6.4.2011) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2011 (S.I. 2011/451), regs. 1, 2(5)(c) (with regs. 3, 4)

Regulations 2(1) and 16(3)

[F3 SCHEDULE 1A E+W+S CONDITIONS FOR TREATMENT OF NATURAL MINERAL WATER AND SPRING WATER WITH ACTIVATED ALUMINA TO REMOVE FLUORIDE

Textual Amendments

F3 Sch. 1A inserted (9.4.2010) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2010 (S.I. 2010/433), regs. 1, 8, Sch. 1

1.   A person seeking to have authorised a treatment of natural mineral water and spring water with activated alumina in order to remove fluoride shall— E+W+S

(a) apply in writing to the relevant authority within whose area the water is extracted;

(b) permit representatives of that authority to examine the proposed method of treatment and place of treatment and take samples for analysis in accordance with regulation 17; and

(c) provide such information in support of the application as is requested by the relevant authority.

2.   The relevant authority shall assess the application and any information in its possession and shall authorise the treatment if it is satisfied that— E+W+S

(a) Articles 1 to 3 of Regulation 115/2010 are complied with in relation to the treatment; and

(b) the treatment does not have a disinfectant action.

3.   Where the relevant authority decides to authorise a treatment pursuant to paragraph 2, it shall inform the applicant in writing and state the date from which the authorisation for commercial use of the treatment has effect. E+W+S

4.   Where the relevant authority refuses to authorise a treatment pursuant to paragraph 2, it shall inform the applicant in writing, stating its reasons. E+W+S

5.   Where a treatment has been authorised pursuant to paragraph 2, the person carrying out the treatment must, for the purpose of enabling the relevant authority to assess whether the conditions in paragraph 2 continue to be satisfied— E+W+S

(a) permit representatives of the authority to examine the method of treatment and place of treatment and take samples for analysis in accordance with regulation 17; and

(b) provide such information related to the treatment as is requested by the authority.

6.   If the relevant authority is satisfied that the conditions specified in paragraph 2 are no longer fulfilled, it may withdraw authorisation of a treatment by giving the person carrying out the treatment a written notice stating the grounds for withdrawal. E+W+S

7.   Where the relevant authority has informed an applicant under paragraph 4 of its refusal to authorise a treatment under paragraph 2 or withdraws authorisation of a treatment under paragraph 6, the person who wishes to carry out the treatment may apply to [F4 the Secretary of State] for a review of that decision. E+W+S

Textual Amendments

F4 Words in Sch. 1A para. 7 substituted (6.4.2011) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2011 (S.I. 2011/451), regs. 1, 2(5)(d) (with regs. 3, 4)

8.   Upon receiving the application for review, [F5 the Secretary of State] shall — E+W+S

(a) make such enquiry into the matter as may seem to [F5 the Secretary of State] to be appropriate; and

(b) having considered the results of that enquiry and any relevant facts elicited by it, either confirm the decision or direct the relevant authority to grant or restore, as appropriate, authorisation of the treatment in respect of which the application was made.

Textual Amendments

F5 Words in Sch. 1A para. 8 substituted (6.4.2011) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2011 (S.I. 2011/451), regs. 1, 2(5)(e) (with regs. 3, 4)

9.   In the case of such a direction, the relevant authority shall comply with the direction.] E+W+S

Regulations 10 and 13

[F6 SCHEDULE 2 E+W+S Requirements for water bottled and labelled as “spring water” and bottled drinking water

Textual Amendments

F6 Sch. 2 substituted (6.4.2018) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018 (S.I. 2018/352), reg. 1(1), Sch. 1

PART 1 E+W+S Requirements for water bottled and labelled as “spring water” and bottled drinking water

Water bottled and labelled as “spring water” and bottled drinking water meet the requirements of this Schedule if—

(a) in relation to each of the parameters specified in the first column of the tables in Part 2 (microbiological parameters) and Part 3 (chemical parameters), it does not contain the parameter at a concentration or value exceeding the concentration or value specified for that parameter in the second column of the relevant table—

(i) as measured by reference to the unit of measurement specified in the third column of the relevant table, and

(ii) as read, in the case of the table in Part 3, with any further provision relating to the parameter, or concentration or value for the parameter, specified in the fourth column of the table,

(b) in relation to each of the parameters specified in the first column of the table in Part 4 (radioactive substances), it does not contain the parameter at an activity concentration or value exceeding the activity concentration or value specified for that parameter in the second column of the relevant table as measured by reference to the unit of measurement specified in the third column of the table,

(c) it does not contain (disregarding any parameters covered by sub-paragraphs (a) and (b)), any micro-organism, parasite or any other property, element or substance at a concentration or value that would constitute a potential danger to human health, and

(d) it does not contain any substance (whether or not a parameter) at a concentration or value that, in conjunction with any other property, element, substance or organism it contains (whether or not a parameter), would constitute a potential danger to human health.

PART 2 E+W+S Parametric values for microbiological parameters

Parameter	Parametric value	Unit of measurement
Escherichia coli (E. coli)	0/250 ml	number/250 ml
Enterococci	0/250 ml	number/250 ml
Pseudomonas aeruginosa	0/250 ml	number/250ml
Colony count 22ºC	100/ml	number/ml
Colony count 37ºC	20/ml	number/ml

PART 3 E+W+S Parametric concentrations for chemical parameters

Parameter	Parametric concentration	Unit of measurement	Further provision
Acrylamide	0.10	µg/l
Antimony	5.0	µg Sb/l
Arsenic	10	µg As/l
Benzene	1.0	µg/l
Benzo(a)pyrene	0.010	µg/l
Boron	1.0	mg/l
Bromate	10	µg/l BrO3/l
Cadmium	5.0	µg Cd/l
Chromium	50	µg Cr/l
Copper	2.0	mg Cu/l
Cyanide	50	µg CN/l
1,2-dichloroethane	3.0	µg/l
Epichlorohydrin	0.10	µg/l
Fluoride	1.5	mg F/l
Lead	10	µg Pb/l
Mercury	1.0	µg Hg/l
Nickel	20	µg Ni/l
Nitrate	50	mg NO3/l	The concentration (mg/l) of nitrate divided by 50 added to the concentration (mg/l) of nitrite divided by 3 must not exceed 1.
Nitrite	0.50	mg NO2/l	The concentration (mg/l) of nitrate divided by 50 added to the concentration (mg/l) of nitrite divided by 3 must not exceed 1.
Pesticides—			Only those pesticides which are likely to be present in a given water must be monitored.
(a) individual substances—
(i) in the case of aldrin, dieldrin, heptachlor and heptachlor epoxide	0.030	µg/l	The parametric concentration applies to each individual pesticide.
(ii) in the case of other individual pesticides	0.10	µg/l	The parametric concentration applies to each individual pesticide.
(b) total pesticides	0.50	µg/l	The concentration for “total pesticides” refers to the total sum of the concentrations of all the individual pesticides detected and quantified in the monitoring procedure.
Polycyclic aromatic hydrocarbons	0.10	µg/l	The parametric concentration applies to the total sum of the concentrations of all the individual polycyclic aromatic hydrocarbons detected and quantified in the monitoring procedure.
Selenium	10	µg Se/l
Tetrachloroethene and trichloroethene	10	µg/l	The parametric concentration applies to the total sum of the concentrations of both of the parameters specified in the first column.
Trichloromethanes	100	µg/l	The parametric concentration applies to the total sum of the concentrations of all the individual trichloromethanes detected and quantified in the monitoring procedure.
Vinyl chloride	0.50	µg/l

PART 4 E+W+S Parametric activity concentrations for radon and tritium and parametric value for indicative dose

Parameter	Parametric activity concentration or value	Unit of Measurement
Radon	100	Bq/l
Tritium	100	Bq/l
Indicative Dose	0.10	mSv]

Regulations 4(1)(a) and (d)(i),(2)(a) and (c), (8) and (9) and16(1)(a)(iii)

SCHEDULE 3 E+W+S Recognition of natural mineral waters

PART 1 E+W+S Natural mineral waters extracted from the ground in England

1.  A person seeking to have water which is extracted from the ground in England recognised as a natural mineral water for the purposes of Article 1 shall make application in writing to the relevant authority within whose area the water is extracted, giving the particulars set out in paragraph 2. E+W+S

2.  The particulars are— E+W+S

(a) those specified in paragraph 1 of Part 3;

(b) any other information showing that the matters specified in paragraphs 2 and 3 of Part 3 are established; and

(c) such evidence as is satisfactory to show that the water contains no substance listed in Schedule 6 at a level which exceeds the maximum limit specified in relation to that substance in that Schedule.

3.  In so far as particulars of any of the anions, cations, non–ionised compounds or trace elements specified in column 1 of Schedule 5 are required to be given pursuant to sub–paragraph (b) of paragraph 2, the concentration of each such anion, cation, non–ionised compound or trace element shall be expressed in those particulars in the unit of measurement specified opposite to it in column 2 of that Schedule. E+W+S

4.  Where such particulars have been so given, the relevant authority shall assess them and shall recognise the water to which those particulars relate as natural mineral water if it is satisfied that— E+W+S

(a) the water is natural mineral water which complies with paragraph 3 of Section I of Annex I; and

(b) the characteristics of the water have been assessed in accordance with —

(i) the points numbered 1 to 4 set out in paragraph 2(a) of Section I of Annex I,

(ii) the requirements and criteria listed in Part 3 of this Schedule, and

(iii) recognised scientific methods.

5.  The relevant authority shall, on recognising a natural mineral water in accordance with paragraph 4, publish an announcement of such recognition and the grounds on which it has been granted in the London Gazette. E+W+S

PART 2 E+W+S Natural mineral waters extracted from the ground in a [F7 Third Country]

Textual Amendments

F7 Words in Sch. 3 Pt. 2 heading substituted (31.12.2020) by The Food (Amendment) (England) (EU Exit) Regulations 2019 (S.I. 2019/150), regs. 1, 3(6)(a); 2020 c. 1, Sch. 5 para. 1(1)

1.  A person seeking to have a water which is extracted from the ground in a [F8 third country] recognised as a natural mineral water for the purposes of Article 1 shall make application in writing to [F9 the Secretary of State], giving the particulars set out in paragraph 2. E+W+S

Textual Amendments

F8 Words in Sch. 3 Pt. 2 para. 1 substituted (31.12.2020) by The Food (Amendment) (England) (EU Exit) Regulations 2019 (S.I. 2019/150), regs. 1, 3(6)(b); 2020 c. 1, Sch. 5 para. 1(1)

F9 Words in Sch. 3 Pt. 2 para. 1 substituted (6.4.2011) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2011 (S.I. 2011/451), regs. 1, 5(f) (with regs. 3, 4)

2.  The particulars are— E+W+S

(a) those specified in paragraph 1 of Part 3;

(b) any other information showing that the matters specified in paragraphs 2 and 3 of Part 3 are established; and

(c) such evidence as is satisfactory to show that the water contains no substance listed in Schedule 6 at a level which exceeds the maximum limit specified in relation to that substance in that Schedule.

3.  In so far as particulars of any of the anions, cations, non–ionised compounds or trace elements specified in column 1 of Schedule 5 are required to be given pursuant to sub-paragraph (b) of paragraph 2, the concentration of each such anion, cation, non–ionised compound or trace element shall be expressed in those particulars in the unit of measurement specified opposite to it in column 2 of that Schedule. E+W+S

4.   [F10 The Secretary of State] shall recognise such a water if the responsible authority of the country in which the water is extracted has certified that— E+W+S

(a) it is satisfied —

(i) that the requirements in paragraphs 2 and 3 of Part 3 are established, and

(ii) with the evidence given pursuant to sub–paragraph (c) of paragraph 2; and

(b) periodic checks are made to ascertain that—

(i) the water is natural mineral water which complies with paragraph 3 of Section I of Annex I,

(ii) the characteristics of the water are assessed in accordance with—

(aa) points numbered 1 to 4 set out in paragraph 2(a) of Section I of Annex I;

(bb) the requirements and criteria listed in Part 3; and

(cc) recognised scientific methods, and

(iii) the provisions of Schedule 4 are being applied by the person exploiting the spring.

Textual Amendments

F10 Words in Sch. 3 Pt. 2 para. 4 substituted (6.4.2011) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2011 (S.I. 2011/451), regs. 1, 2(6) (with regs. 3, 4)

5.  Recognition of such water shall lapse after a period of five years unless the responsible authority of the country in which the water is extracted has renewed the certification required by paragraph 4. E+W+S

6.   [F11 The Secretary of State] shall, on recognising water in accordance with this Part of this Schedule, publish an announcement of such recognition in the London Gazette, the Edinburgh Gazette and the Belfast Gazette.

Textual Amendments

F11 Words in Sch. 3 para. 6 substituted (6.4.2011) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2011 (S.I. 2011/451), regs. 1, 2(6) (with regs. 3, 4)

PART 3 E+W+S Requirements and criteria for recognition as a natural mineral water

1.  Geological and hydrological surveys must include the following particulars— E+W+S

(a) the exact site of the catchment with an indication of its altitude, on a map with a scale of not more than 1:1,000;

(b) a detailed geological report on the origin and nature of the terrain;

(c) the stratigraphy of the hydrogeological layer;

(d) a description of the catchment operations; and

(e) the demarcation of the area or details of other measures protecting the spring against pollution.

2.  Physical, chemical and physico-chemical surveys must establish— E+W+S

(a) the rate of flow of the spring;

(b) the temperature of the water at source and the ambient temperature;

(c) the relationship between the nature of the terrain and the nature and type of minerals in the water;

(d) the dry residues at 180°C and 260°C;

(e) the electrical conductivity or resistivity, with the measurement temperature being specified;

(f) the hydrogen ion concentration (pH);

(g) the anions and cations;

(h) the non-ionised elements;

(i) the trace elements;

(j) the radio-actinological properties at source;

(k) where appropriate, the relative isotope levels of the constituent elements of water, oxygen (¹⁶O — ¹⁸O) and hydrogen (protium, deuterium, tritium); and

(l) the toxicity of certain constituent elements of the water, taking account of the limits laid down for each of them.

3.  Microbiological analysis at source must show— E+W+S

(a) the absence of parasites and pathogenic micro-organisms;

(b) quantitative determination of the revivable colony count indicative of faecal contamination, demonstrating—

(i) absence of Escherichiacoli and other coliforms in 250 ml at 37°C and 44.5°C,

(ii) absence of faecal streptococci in 250 ml,

(iii) absence of sporulated sulphite-reducing anaerobes in 50ml, and

(iv) absence of Pseudomonasaeruginosa in 250 ml; and

(c) the revivable total colony count per ml of water—

(i) at 20 to 22°C in 72 hours on agar-agar or an agar-gelatine mixture, and

(ii) at 37°C in 24 hours on agar-agar.

4.—(1) Subject to sub-paragraph (2), clinical and pharmacological analyses must be carried out in accordance with scientifically recognised methods and should be suited to the particular characteristics of the natural mineral water and its effects on the human organism, such as diuresis, gastric and intestinal functions, compensation for mineral deficiencies. E+W+S

(2) Clinical analyses may, in appropriate cases, take the place of analyses referred to in sub-paragraph (1), provided that the consistency and concordance of a substantial number of observations enable the same results to be obtained.

Regulations 4(2)(b), 5(1)(c) and (2),7(3), 9(2)(b), 10(1)(b) and (3) and16(1)(a)(iv) and paragraph 1(b) ofSchedule 1 and paragraph 4(b)(iii) of Part 2 of Schedule 3

SCHEDULE 4 E+W+S Exploitation and bottling requirements for natural mineral water and spring water

1.  Equipment for exploiting the water must be so installed as to avoid any possibility of contamination and to preserve the properties corresponding to those ascribed to it which the water possesses at source. E+W+S

2.  The spring or outlet must be protected against the risks of pollution. E+W+S

3.  The catchment, pipes and reservoirs must be of materials suitable for water and so built as to prevent any chemical, physico-chemical or microbiological alteration of the water. E+W+S

[F12 4.   The conditions of exploitation, particularly the washing and bottling equipment, must meet hygiene requirements. In particular, the containers must be so treated or manufactured as to avoid adverse effects on the microbiological and chemical characteristics of the water.] E+W+S

Textual Amendments

F12 Sch. 4 para. 4 substituted (16.7.2009) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2009 (S.I. 2009/1598), regs. 1, 8(a)

5.—(1) Subject to sub-paragraphs (2) and (3), water must not be transported in containers other than those authorised for distribution to the ultimate consumer. E+W+S

(2) Natural mineral water may be transported from the spring to the bottling plant in a container which is not for distribution to the ultimate consumer if on or before 17^th July 1980 water from that spring was so transported.

[F13 (3) Water distributed to the ultimate consumer in a bottle marked or labelled with the description “spring water” may be transported from the spring to the bottling plant in a container which is not for distribution to the ultimate consumer if, on or before 13th December 1996, water from that spring was so transported.]

Textual Amendments

F13 Sch. 4 para. 5(3) substituted (16.7.2009) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2009 (S.I. 2009/1598), regs. 1, 8(b)

6.—(1) The revivable total colony count of the water at source, determined according to sub-paragraph (2), shall conform to the normal viable colony count of that water and shall not show that the source of that water is contaminated. E+W+S

(2) The colony count is that determined per ml of water—

(a) at 20 to 22 ^oC in 72 hours on agar-agar or an agar-gelatine mixture; and

(b) at 37 ^oC in 24 hours on agar-agar.

7.—(1) After bottling, the total colony count of the water at source may not exceed— E+W+S

(a) 100 per ml at 20 to 22 ^oC in 72 hours on agar-agar or an agar-gelatine mixture; and

(b) 20 per ml at 37 ^oC in 24 hours on agar-agar.

(2) The total colony count shall be measured within the period of 12 hours following bottling, the water being maintained at 4 ^oC +/- 1 ^oC during the period before which it is measured.

[F14 8.   Both at source and during its marketing, water shall be free from— E+W+S

(a) parasites and pathogenic micro-organisms;

(b) Escherichia coli and other coliforms and faecal streptococci in any 250 ml sample examined;

(c) sporulated sulphite-reducing anaerobes in any 50 ml sample examined; and

(d) Pseudomonas aeruginosa in any 250 ml sample examined.]

Textual Amendments

F14 Sch. 4 para. 8 substituted (16.7.2009) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2009 (S.I. 2009/1598), regs. 1, 8(c)

Regulation 4(9) and paragraph 3 of Part 1 of Schedule 3

SCHEDULE 5 E+W+S Particulars of anions, cations, non–ionised compounds and trace elements

Anions	Unit of measurement
Borate BO3–	mg/1
Carbonate CO32–	mg/1
Chloride Cl–	mg/1
Fluoride F–	mg/l
Hydrogen Carbonate HCO3–	mg/1
Nitrate NO3–	mg/1
Nitrite NO2–	mg/1
Phosphate PO43–	mg/1
Silicate SiO2	mg/1
Sulphate SO42–	mg/1
Sulphide S2–	mg/1
Cations	Unit of measurement
Aluminium A1	mg/1
Ammonium NH4+	mg/1
Calcium Ca	mg/1
Magnesium Mg	mg/1
Potassium K	mg/l
Sodium Na	mg/1
Non–ionised compounds	Unit of measurement
Total organic carbon C	mg/1
Free carbon dioxide CO2	mg/1
Silica SiO2	mg/1
Trace elements	Unit of measurement
Barium Ba	µg/l
Bromine (total) Br	µg/l
Cobalt Co	µg/l
Copper Cu	µg/l
Iodine (total) I	µg/l
Iron Fe	µg/l
Lithium Li	µg/l
Manganese Mn	µg/l
Molybdenum Mo	µg/l
Strontium Sr	µg/l
Zinc Zn	µg/1

Regulation 7(1) and (2) andparagraph 2(c)of Part 1 of Schedule 3,paragraph 2(c) of Part 2 of Schedule 3and Notes 1 and 2 of Schedule 7

SCHEDULE 6 E+W+S Maximum limits for constituents of natural mineral waters

Note: The constituents described above refer to constituents naturally present in the water at source and not to substances present as the result of contamination.
Constituents	Maximum limits (mg/l)
Antimony	0.0050
Arsenic	0.010 (as total)
Barium	1.0
Cadmium	0.003
Chromium	0.050
Copper	1.0
Cyanide	0.070
Fluoride	5.0
Lead	0.010
Manganese	0.50
Mercury	0.0010
Nickel	0.020
Nitrate	50
Nitrite	0.1
Selenium	0.010

Regulation 7(2)

SCHEDULE 7 E+W+S Performance characteristics for analysing the constituents in Schedule 6

Notes: 1. The method of analysis used to measure the concentration of the constituents in Schedule 6 shall be capable of measuring concentrations equal to the parametric value with the specified accuracy, precision and detection limits.
2. Regardless of the sensitivity of the method of analysis, the result must be expressed to at least the same number of decimal places as the maximum limit set out in Schedule 6 for the particular constituent being analysed.
3. Accuracy is the systematic error and represents the difference between the average value of a large number of repeated measurements and the exact value.
4. Precision represents the random error and is expressed in general as the standard deviation (within a batch and between batches) of a sample of results from the average.
5. Acceptable precision is equal to twice the relative standard deviation.
6. The detection limit is— (a) three times the relative standard deviation within a batch of a natural sample containing a low concentration of the constituent; or (b) five times the relative standard deviation within a batch of a virgin sample.
7. The method should make it possible to determine cyanide in all its forms.
Constituent	Accuracy of parametric value in %	Precision of parametric value	Detection limit of parametric value in %
Antimony	25	25	25
Arsenic	10	10	10
Barium	25	25	25
Cadmium	10	10	10
Chromium	10	10	10
Copper	10	10	10
Cyanides	10	10	10
Fluoride	10	10	10
Lead	10	10	10
Manganese	10	10	10
Mercury	20	10	20
Nickel	10	10	10
Nitrate	10	10	10
Nitrite	10	10	10
Selenium	10	10	10

Regulation 8(1)(e)

SCHEDULE 8 E+W+S Labelling indications for natural mineral water and criteria for use

Indication	Criteria
Low mineral content	Mineral salt content, calculated as a fixed residue, not greater than 500 mg/l
Very low mineral content	Mineral salt content, calculated as a fixed residue, not greater than 50 mg/l
Rich in mineral salts	Mineral salt content. Calculated as a fixed residue, greater than 1500 mg/l
Contains bicarbonate	Bicarbonate content greater than 600 mg/l
Contains sulphate	Sulphate content greater than 200 mg/l
Contains chloride	Chloride content greater than 200 mg/l
Contains calcium	Calcium content greater than 150 mg/l
Contains magnesium	Magnesium content greater than 50 mg/l
Contains fluoride	Fluoride content greater than 1 mg/l
Contains iron	Bivalent iron content greater than 1 mg/l
Acidic	Free carbon dioxide content greater than 250 mg/l
Contains sodium	Sodium content greater than 200 mg/l
Suitable for a low-sodium diet	Sodium content less than 20 mg/l

Regulation 16(5)(a)(iii), (b)(ii) and (d)

F15 SCHEDULE 9 E+W+S PROPERTIES, ELEMENTS, SUBSTANCES AND ORGANISMS, NOT BEING PARAMETERS, WHOSE CONCENTRATION OR VALUE IN BOTTLED DRINKING WATER AND SPRING WATER MUST BE DETERMINED BY AUDIT MONITORING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Textual Amendments

F15 Sch. 9 omitted (6.4.2018) by virtue of The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018 (S.I. 2018/352), regs. 1(1), 11(a)

Regulation 16(5)(b) (i)

F16 SCHEDULE 10 E+W+S PARAMETERS , PROPERTIES, ELEMENTS, SUBSTANCES AND ORGANISMS IN RELATION TO WHICH CHECK MONITORING MUST BE CARRIED OUT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Textual Amendments

F16 Sch. 10 omitted (6.4.2018) by virtue of The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018 (S.I. 2018/352), regs. 1(1), 11(b)

Regulation 16(5)(c)

F17 SCHEDULE 11 E+W+S MINIMUM FREQUENCIES FOR SAMPLING AND ANALYSIS OF SPRING WATER AND BOTTLED DRINKING WATER

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Textual Amendments

F17 Sch. 11 omitted (6.4.2018) by virtue of The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018 (S.I. 2018/352), regs. 1(1), 11(c)

Regulation 16A

[F18 SCHEDULE 12 E+W+S Monitoring of water bottled and labelled as “spring water” and bottled drinking water

Textual Amendments

F18 Sch. 12 inserted (6.4.2018) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018 (S.I. 2018/352), reg. 1(1), Sch. 2

PART 1 E+W+S Interpretation

General E+W+S

1.   In this Schedule—

“average” means mean average;

“the BSI” means the British Standards Institution;

“delegate” means a person to whom a task has been delegated by a food authority under paragraph 14, as read with paragraph 56, or a person to whom a food authority intends to delegate such a task (as the case may be);

“indicative dose” means the committed effective dose for one year of ingestion resulting from all the radionuclides (whether of natural or artificial origin) whose presence has been detected in a supply of water intended for human consumption but excluding potassium-40, radon, tritium and short-lived radon decay products;

“limit of quantification” has the meaning given in Article 2(2) of Commission Directive 2009/90/EC laying down, pursuant to Directive 2000/60/EC of the European Parliament and of the Council, technical specifications for chemical analysis and monitoring of water status;

“paragraph 45 determination” means a determination under paragraph 45 relating to indicative dose”;

“parametric concentration”, in relation to a parameter specified in the first column of the table in Part 3 of Schedule 2 or a parameter specified in the first column of the table in Section 1 of Part 9 for which a maximum concentration (as opposed to a value) is set, means the maximum concentration given for the parameter in the second column of the relevant table, as measured by reference to the unit of measurement specified in the third column of the relevant table;

“radioactive substance” has the meaning given in Article 2(2) of Council Directive 2013/51/Euratom laying down requirements for the protection of the health of the general public with regard to radioactive substances in water intended for human consumption;

F19 ...

[F20 “Regulation (EU) 2017/625” means Regulation (EU) 2017/625 of the European Parliament and of the Council on official controls and other official activities performed to ensure the application of food and feed law, rules on animal health and welfare, plant health and plant protection products;]

“sample” means a sample taken under this Schedule;

“trueness” (the systematic error) means the difference between the mean value of the large number of repeated measurements and the true value, as further described in ISO 5725-1:1994(en) entitled “Accuracy (trueness and precision) of measurement methods and results – Part 1: General principles and definitions” published by the International Organization for Standardization on 22nd December 1994, as amended by ISO 5725-1:1994/Cor 1:1998 entitled “Accuracy (trueness and precision) of measurement methods and results – Part 1: General principles and definitions TECHNICAL CORRIGENDUM 1” published by the International Organization for Standardization on 2nd May 1998;

“uncertainty of measurement” means a non-negative parameter characterising the dispersion of the quantity values being attributed to a measure based on the information used;

“year” means, unless a contrary intention appears, a calendar year or such other 12 month period as a food authority may, from time to time, decide to use for the purpose of its monitoring programme.

Textual Amendments

F19 Words in Sch. 12 para. 1 omitted (14.12.2019) by virtue of The Official Controls (Animals, Feed and Food, Plant Health Fees etc.) Regulations 2019 (S.I. 2019/1488), regs. 1(1), 24(a)(i)

F20 Words in Sch. 12 para. 1 inserted (14.12.2019) by The Official Controls (Animals, Feed and Food, Plant Health Fees etc.) Regulations 2019 (S.I. 2019/1488), regs. 1(1), 24(a)(ii)

Delegated tasks E+W+S

2.   Where a food authority has entered into an arrangement with a person under paragraph 14, as read with Part 10, for a delegate to carry out a task specified in the first column of the table in Section 2 of Part 10 on its behalf, any reference to a food authority in that provision, and in any related provision in this Schedule, is to be read as a reference to the delegate for the purpose of carrying out that task during the duration of the delegation arrangement.

PART 2 E+W+S General

Application E+W+S

3.   This Schedule applies to the monitoring of—

(a) water that is bottled and labelled as “spring water” by a food business in the course of its business as a bottler of water, whether the bottling of water is its main business or part of its business, and

(b) drinking water that is bottled by a food business in the course of its business as a bottler of water, whether the bottling of water is its main business or part of its business.

Sampling: general E+W+S

4.— (1) For the purpose of carrying out its obligations under the provisions specified in sub-paragraph (2), each food authority must take and analyse samples of any water bottled in its area to which this Schedule applies.

(2) The provisions are—

(a) paragraph 7(1) (microbiological parameters);

(b) paragraph 8(1) (chemical parameters);

(c) paragraph 9, as read with paragraphs 23 and 25(1) (radon);

(d) paragraph 10, as read with paragraphs 29 and 31(1) (tritium);

(e) paragraph 11 (indicative dose), as read with—

(i) paragraph 38(2), where a decision is taken by the food authority under paragraph 38(1) to screen water by determining its gross alpha activity to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water;

(ii) paragraph 39(2), where a decision is taken by the food authority under paragraph 39(1) to screen water by determining its gross beta activity to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water;

(iii) paragraph 40(2), where a decision is taken by the food authority under paragraph 40(1) to screen water by analysing one radionuclide to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water;

(iv) paragraph 41(2), where a decision is taken by the food authority under paragraph 41(1) to screen water by analysing more than one radionuclide to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water;

(v) paragraph 43(1) (determination relating to the presence and concentration of radionuclides);

(f) paragraph 12, as read with paragraph 50(1) (indicator parameters);

(g) paragraph 13 (other parameters not mentioned in this sub-paragraph).

(3) For the purpose of its sampling obligations under this Schedule, a food authority must take samples of water at the point at which the water is put into a bottle.

Sampling: non-radioactive substances E+W+S

5.— (1) In the case of samples of water that a food authority must take and analyse to enable it to discharge its obligations under the provisions specified in [F21 paragraph 4(2)(a),] (b), (f) and (g), each food authority must take and analyse such samples regularly, having regard to the provisions contained in—

(a) Article 17(2) of Regulation (EC) No 178/2002 of the European Parliament and of the Council laying down the general principles and requirements of food law, establishing the European Food Safety Authority and laying down procedures in matters of food safety (monitoring responsibilities), and

[F22 (b) Article 9 of Regulation (EU) 2017/625.]

(2) Where, under sub-paragraph (1), a food authority only takes one sample in a year of any water in its area to which this Schedule applies, the authority must take the samples from year to year at intervals that are spread out in such a way—

(a) to avoid the results, when considered together, giving a potentially distorted picture of the state of the water because the samples have been taken too closely together in time, and

(b) so that the results, when considered together, provide information about the water that is representative of the quality of the water during the relevant years.

(3) Where, under sub-paragraph (1), a food authority takes more than one sample in a year of any water in its area to which this Schedule applies, the authority must take the samples at intervals that are spread out throughout the year in such a way—

(a) to avoid the results, when considered together, giving a potentially distorted picture of the state of the water because the samples have been taken too closely together in time, and

(b) so that the results, when considered together, provide information about the water that is representative of the quality of the water during the course of that year.

Textual Amendments

F21 Words in Sch. 12 para. 5(1) substituted (29.3.2019) by The Environment, Food and Rural Affairs (Miscellaneous Amendments etc.) Regulations 2019 (S.I. 2019/526), regs. 1(2), 27(2)(a)

F22 Sch. 12 para. 5(1)(b) substituted (14.12.2019) by The Official Controls (Animals, Feed and Food, Plant Health Fees etc.) Regulations 2019 (S.I. 2019/1488), regs. 1(1), 24(b)(i)

Monitoring: radioactive substances E+W+S

6.   In the case of samples that a food authority must take and analyse to discharge its obligations under the provisions specified in paragraph 4(2)(c) to (e), the samples must—

(a) be taken and analysed by the food authority no less frequently than provided for in the table in Part 3, unless—

(i) a decision is taken by the authority under paragraph 27, 33, 42 or 47 to reduce the minimum frequency at which it must take and analyse samples, in which case the authority must take and analyse samples at the reduced minimum frequency decided by it under the relevant paragraph until such time as it takes a different decision relating to the minimum frequency at which relevant samples must be taken and analysed;

(ii) a decision is taken by the authority under paragraph 42 or 47 to stop taking and analysing samples, in which case the authority, in accordance with that decision, is not obliged to take and analyse samples until such time as it takes a different decision relating to the minimum frequency at which relevant samples must be taken and analysed;

(b) be taken, in so far as possible, so that the number of samples are distributed equally in time and (where appropriate) location.

Microbiological parameters E+W+S

7.— (1) A food authority must monitor the value for each of the parameters specified in the first column of the table in Part 2 of Schedule 2 (microbiological parameters) in any water in its area to which this Schedule applies by analysing a sample of the water to determine whether the value for the parameter in the sample exceeds the value specified for the parameter in the second column of the table, as measured by reference to the unit of measurement specified in the third column of the table.

(2) For the purpose of the determination required by sub-paragraph (1), the food authority must analyse the sample using the method of analysis for the relevant parameter specified in Part 4.

Chemical parameters E+W+S

8.— (1) A food authority must monitor the concentration of each of the parameters specified in the first column of the table in Part 3 of Schedule 2 (chemical parameters) in any water in its area to which this Schedule applies by analysing a sample of the water to determine whether the concentration of the parameter in the sample exceeds the concentration specified for the relevant parameter in the second column of the table—

(a) as measured by reference to the unit of measurement specified in the third column of the table, and

(b) as read, in the case of a parameter for which there is an entry in the fourth column of the table, with the further provision relating to the parameter or parametric concentration specified in that entry.

(2) For the purpose of the determination required by sub-paragraph (1), the food authority must analyse the sample using a method of analysis that complies with Part 5.

(3) But sub-paragraph (2) does not apply, and it is not necessary for a food authority to analyse a sample of water under sub-paragraph (1) to determine whether the concentration of acrylamide, epichlorohydrin or vinyl chloride exceeds the concentration specified for that parameter in the second column of the table in Part 3 of Schedule 2, where—

(a) the food authority is satisfied that the water, before it is bottled, does not come into contact with a pipe or other construction product that has been constructed using that parameter as a component in its construction, or

(b) in other cases, the food authority is satisfied, on the basis of a certificate of conformity, declaration of conformity or declaration of performance relating to a pipe or other construction product that the water comes into contact with, or may come into contact with, before being bottled, and any other related information that it considers to be relevant, that any residual monomer concentration of that parameter in the water does not exceed the concentration for that parameter specified in the second column of the table in Part 3 of Schedule 2.

(4) A food authority must not use the uncertainty of measurement percentage specified in the second column of the table in Section 2 of Part 5 (which is concerned with whether a method of analysis complies with minimum performance characteristics) as an additional tolerance when determining whether a parameter specified in the first column of the table in Part 3 of Schedule 2 exceeds the concentration for that parameter specified in the second column of the table in Part 3 of Schedule 2.

(5) In sub-paragraph (3)(b)—

“certificate of conformity” means a certificate of conformity issued on or before 30th June 2013—

(a)

under the Construction Products Regulations 1991; F23 ...

(b)

F23 ...

“construction product” has the meaning given in point (1) of Article 2 of Regulation (EU) No 305/2011 of the European Parliament and of the Council laying down harmonised conditions for the marketing of construction products and repealing Council Directive 89/106/EEC;

“declaration of conformity” means a declaration of conformity issued on or before 30th June 2013—

(a)

under the Construction Products Regulations 1991; F24 ...

(b)

F24 ...

“declaration of performance” means a declaration of performance drawn up in accordance with Article 4 of Regulation (EU) No 305/2011 of the European Parliament and of the Council.

Textual Amendments

F23 Words in Sch. 12 para. 8(5) omitted (31.12.2020) by virtue of The Food (Amendment) (England) (EU Exit) Regulations 2019 (S.I. 2019/150), regs. 1, 3(7)(a); 2020 c. 1, Sch. 5 para. 1(1)

F24 Words in Sch. 12 para. 8(5) omitted (31.12.2020) by virtue of The Food (Amendment) (England) (EU Exit) Regulations 2019 (S.I. 2019/150), regs. 1, 3(7)(b); 2020 c. 1, Sch. 5 para. 1(1)

Radon E+W+S

9.   A food authority must monitor the level of radon in any water in its area to which this Schedule applies in accordance with Part 6.

Tritium E+W+S

10.   A food authority must monitor the level of tritium in any water in its area to which this Schedule applies in accordance with Part 7.

Indicative dose E+W+S

11.   A food authority must monitor the level of the indicative dose for any water in its area to which this Schedule applies in accordance with Part 8.

Indicator parameters E+W+S

12.   A food authority must monitor the concentration or value (as the case may be) of each of the parameters specified in the first column of the table in Section 1 of Part 9 (indicator parameters) in any water in its area to which this Schedule applies in accordance with Part 9.

Other parameters E+W+S

13.   Where a food authority believes, or has reason to suspect, that a property, element, substance or organism that is not specified in any of the tables in Schedule 2 or the table in Section 1 of Part 9, may be present in any water in its area to which this Schedule applies at any concentration, or in any number, that may constitute a potential danger to human health, it must take and analyse samples of the water, on a case by case basis, to determine whether that property, element, substance or organism is present in the water and whether it is present in the water at any concentration, or in any number, that may constitute a potential danger to human health.

Delegation of tasks E+W+S

14.   To enable a food authority to discharge its functions under this Schedule, a food authority may from time to time enter into an arrangement with another person under which the food authority delegates specified tasks to the delegate to carry out on behalf of the food authority on condition that—

(a) such arrangement is in accordance with—

(i) Part 10, and

[F25 (ii) Article 29 of Regulation (EU) 2017/625, and]

[F26 (b) the food authority notifies the Secretary of State, in advance of the proposed delegation, of the tasks that are being delegated to a delegated body.]

Textual Amendments

F25 Sch. 12 para. 14(a)(ii) substituted (14.12.2019) by The Official Controls (Animals, Feed and Food, Plant Health Fees etc.) Regulations 2019 (S.I. 2019/1488), regs. 1(1), 24(b)(ii)(aa)

F26 Sch. 12 para. 14(b) substituted (14.12.2019) by The Official Controls (Animals, Feed and Food, Plant Health Fees etc.) Regulations 2019 (S.I. 2019/1488), regs. 1(1), 24(b)(ii)(bb)

Quality management practices E+W+S

15.— (1) A food authority must not analyse a sample taken for the purpose of carrying out its monitoring obligations under regulation 16A, as read with this Schedule, unless quality management practices that comply with BS EN ISO/IEC 17025:2017 entitled “General requirements for the competence of testing and calibration laboratories” (ISBN 978 0 580 88466 5) published by the BSI on 31st December 2017, or another equivalent standard accepted at international level, are being complied with at the laboratory in which the sample is analysed.

(2) But, in the case of the analysis of a sample for the purposes of the monitoring obligations under the provisions specified in sub-paragraph (3), it is sufficient if the laboratory at which the sample is analysed has a system of analytical quality control in place that is checked by the United Kingdom Accreditation Service from time to time.

(3) The provisions are those in—

(a) paragraph 9, as read with Part 6 (radon),

(b) paragraph 10, as read with Part 7 (tritium), and

(c) paragraph 11, as read with Part 8 (indicative dose).

Validation and documentation E+W+S

16.— (1) A food authority must ensure that any analysis that it carries out for the purpose its monitoring obligations under regulation 16A, as read with this Schedule, is validated and documented in accordance with BS EN ISO/IEC 17025:2017 entitled “General requirements for the competence of testing and calibration laboratories” (ISBN 978 0 580 88466 5) published by the BSI on 31st December 2017 or another equivalent standard accepted at international level.

(2) But, in the case of the analysis of a sample for the purpose of the monitoring obligations under the provisions specified in sub-paragraph (3), it is sufficient if the laboratory at which the sample is analysed has a system of analytical quality control in place that is checked by the United Kingdom Accreditation Service from time to time.

(3) The provisions are those in—

(a) paragraph 9, as read with Part 6 (radon),

(b) paragraph 10, as read with Part 7 (tritium), and

(c) paragraph 11, as read with Part 8 (indicative dose).

PART 3 E+W+S Minimum sampling and analyses frequencies for monitoring radioactive substances

Average volume of water bottled each day within a supply zone m3	Number of samples per year
(1) The volume of water bottled each day must be calculated as an average taken over a year.
(2) “a supply zone” means a geographically defined area within which water intended for human consumption comes from one or more sources and within which water quality may be considered as being approximately uniform.
1,000 or less	1
More than 1,000 but less than or equal to 10,000	1
	Plus 1 for each 3,300m3 of the average volume produced each day
	Plus 1 for any remaining part of the average volume produced each day that is less than 3,300m3
More than 10,000 but less than or equal to 100,000	3
	Plus 1 for each 10,000 m3 of the average volume produced each day
	Plus 1 for any remaining part of the average volume produced each day that is less than 10,000 m3
More than 100,000	10
	Plus 1 for each 25,000 m3 of the average volume produced each day
	Plus 1 for any remaining part of the average volume produced each day that is less than 25,000 m3

PART 4 E+W+S Methods of analyses relating to specified microbiological parameters

Parameter	Method of analysis
Escherichia coli (E. coli)	BS EN ISO 9308-1:2014+A1:2017 entitled “Water quality — Enumeration of Escherichia coli and coliform bacteria. Part 1: Membrane filtration method for waters with low bacterial background flora (ISO 9308-1:2014)” (ISBN 978 0 580 92379 1) published by the BSI on 31st October 2014, as amended on 28th February 2017, or BS EN ISO 9308-2:2014 entitled “Water quality — Enumeration of Escherichia coli and coliform bacteria. Part 2: Most probable number method” (ISBN 978 0 580 84023 4) published by the BSI on 30th June 2012, as amended by a corrigendum issued on 30th June 2014
Enterococci	BS EN ISO 7899-2:2000, BS 6068-4.4:2000 entitled “Water quality — Detection and enumeration of intestinal enterococci — Part 2: Membrane filtration method” (ISBN 0 580 34953 5) published by the BSI on 15th August 2000
Pseudomonas aeruginosa	BS EN ISO 16266:2008 entitled “Water quality — Detection and enumeration of Pseudomonas aeruginosa — Method by membrane filtration” (ISBN 978 0 580 59736 7) published by the BSI on 31st March 2008
Colony count 22ºC – enumeration of culturable microorganisms	BS EN ISO 6222: 1999, BS 6068-4.5:1999 entitled “Water quality — Enumeration of cultural micro-organisms — Colony count by inoculation in a nutrient agar culture medium” (ISBN 0 580 32495 8) published by the BSI on 15th August 1999
Colony count 36ºC – enumeration of culturable microorganisms	BS EN ISO 6222: 1999, BS 6068-4.5:1999 entitled “Water quality — Enumeration of cultural micro-organisms — Colony count by inoculation in a nutrient agar culture medium” (ISBN 0 580 32495 8) published by the BSI on 15th August 1999

PART 5 E+W+S Methods of analysis relating to chemical parameters

SECTION 1 E+W+S Methods of analysis

Method of analysis E+W+S

17.   In relation to a parameter specified in the first column of the table in Part 3 of Schedule 2 (chemical parameters)—

(a) where there is a method of analysis that meets minimum performance characteristics that can be used by a food authority to analyse a sample for the purpose of making a determination in relation to that parameter under paragraph 8, the food authority must analyse the sample using that method of analysis (or using any one of them in a case where more than one method of analysis meets minimum performance characteristics);

(b) where there is no such method of analysis, the food authority must analyse a sample under paragraph 8 using the best available technique not entailing excessive cost.

Minimum performance characteristics E+W+S

18.— (1) For the purpose of paragraph 17(a), a method of analysis for a parameter specified in the first column of the table in Section 2 (minimum performance characteristics for a method of analysis) is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—

(a) is capable of measuring concentrations equal to the parametric concentration of that parameter with a limit of quantification of 30% or less of the relevant parametric concentration,

(b) has an uncertainty of measurement that does not exceed the percentage of the parametric concentration for the parameter specified in the second column of the table,

(c) in the case of benzo(a)pyrene, complies, where relevant, with the requirement specified in the third column of the table, and

(d) in the case of cyanide, complies with the requirement specified in the fourth column of the table.

(2) In the case of a parameter specified in the first column of the table in Section 2, where a method of analysis that complies with the requirements of sub-paragraph (1) is used to determine whether the concentration of that parameter exceeds the concentration specified for that parameter in the table in Part 3 of Schedule 2, the result of the analysis carried out using that method of analysis must be expressed using at least the same number of significant figures as the number of significant figures used to specify that parametric concentration in the table in Part 3 of Schedule 2.

Minimum performance characteristics: individual pesticides E+W+S

19.— (1) For the purpose of paragraph 17(a), a method of analysis for an individual pesticide is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—

(a) is capable of measuring concentrations equal to the parametric concentration for that pesticide with a limit of quantification of 30% or less of the relevant parametric concentration;

(b) has an uncertainty of measurement that does not exceed 30% of the parametric concentration for that pesticide or, where there is no method of analysis for the pesticide that does not exceed 30% of that concentration, an uncertainty of measurement that does not exceed—

(i) where there is a method of analysis for the pesticide that has an uncertainty of measurement of more than 30% but less than 80%—

(aa) the uncertainty of measurement percentage that applies in relation to that method of analysis, or

(bb) where there is more than one such method of analysis for the pesticide, the lowest of those percentages, or

(ii) 80%, where there is not a method of analysis for the pesticide that has an uncertainty of measurement of less than 80%.

(2) Where a method of analysis that complies with the requirements of sub-paragraph (1) is used to determine whether the concentration of an individual pesticide exceeds the parametric concentration specified in the table in Part 3 of Schedule 2 that applies to that pesticide, the result of the analysis carried out using that method of analysis must be expressed using at least the same number of significant figures as the number of significant figures used to specify the parametric concentration that applies to that pesticide in the table.

Alternative minimum performance characteristics E+W+S

20.— (1) For the purpose of paragraph 17(a), until the end of 31st December 2019, a method of analysis for a parameter specified in the first column of the table in Section 3 (alternative minimum performance characteristics for a method of analysis that may be used until the end of 31st December 2019) is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—

(a) is capable of measuring parametric concentrations with a trueness not less than the percentage of the parametric concentration specified in the second column of the table,

(b) is capable of measuring parametric concentrations with a precision not less than the percentage of the parametric concentration specified in the third column of the table,

(c) has a limit of detection that does not exceed the percentage of the parametric concentration specified in fourth column of the table, and

(d) in the case of cyanide, complies with the requirement specified in the fifth column of the table.

(2) For the purpose of sub-paragraph (1)(b) and the table in Section 3, “precision” (the random error) is twice the relative standard deviation (within a batch and between batches) of the spread of results from the mean as further described in ISO 5725-1:1994(en) entitled “Accuracy (trueness and precision) of measurement methods and results – Part 1: General principles and definitions” published by the International Organization for Standardization on 22nd December 1994, as amended by ISO 5725-1:1994/Cor 1:1998 entitled “Accuracy (trueness and precision) of measurement methods and results – Part 1: General principles and definitions TECHNICAL CORRIGENDUM 1” published by the International Organization for Standardization on 2nd May 1998.

(3) For the purpose of subparagraph (1)(c) and the table in Section 3, the limit of detection is—

(a) three times the standard deviation within a batch of a natural sample containing a low concentration of the parameter, or

(b) five times the standard deviation of a blank sample within a batch.

Uncertainty of measurement E+W+S

21.— (1) For the purpose of paragraph 18(1)(b) and 19(1)(b), the performance criterion for uncertainty of measurement (k = 2) for a parameter specified in the first column of the table in Section 2 is not less than the percentage specified in the second column of the table of the concentration for the parameter specified in the second column of the table in Part 3 of Schedule 2.

(2) Food authorities must estimate uncertainty of measurement for a parameter specified in the first column of the table in Section 2 at the level of the concentration for the parameter specified in the second column of the table in Part 3 of Schedule 2.

SECTION 2 E+W+S Minimum performance characteristics for a method of analysis

Parameters	Uncertainty of measurement - percentage of the parametric concentration	Other requirements relating to the uncertainty of measurement	Other requirements
Antimony	40
Arsenic	30
Benzene	40
Benzo(a)pyrene	50	Where there is no method of analysis for benzo(a)pyrene that has an uncertainty of measurement that does not exceed 50%, the best available method of analysis with an uncertainty of measurement not exceeding 60% must be used.
Boron	25
Bromate	40
Cadmium	25
Chromium	30
Copper	25
Cyanide	30		The method of analysis must determine total cyanide in all forms.
1,2-dichloroethane	40
Fluoride	20
Lead	25
Mercury	30
Nickel	25
Nitrate	15
Nitrite	20
Polycyclic aromatic hydrocarbons—
(a) individual substance	25
(b) total substances	50
Selenium	40
Tetrachloroethenes—
(a) individual substance	50
(b) total substances	30
Trichloroethenes—
(a) individual substance	50
(b) total substances	40
Trihalomethanes—
(a) individual substance	25
(b) total substances	40

SECTION 3 E+W+S Alternative minimum performance characteristics for a method of analysis that may be used until the end of 31st December 2019

Parameters	Trueness - percentage of the parametric concentration	Precision -percentage of the parametric concentration	Limit of detection -percentage of the parametric concentration	Other requirements
Antimony	25	25	25
Arsenic	10	10	10
Benzene	25	25	25
Benzo(a)pyrene	25	25	25
Boron	10	10	10
Bromate	25	25	25
Cadmium	10	10	10
Chromium	10	10	10
Copper	10	10	10
Cyanide	10	10	10	The method of analysis must determine total cyanide in all forms.
1,2-dichloroethane	25	25	10
Fluoride	10	10	10
Lead	10	10	10
Mercury	20	10	20
Nickel	10	10	10
Nitrate	10	10	10
Nitrite	10	10	10
Pesticide – individual substance	25	25	25
Polycyclic aromatic hydrocarbons—
(a) individual substance	25	25	25
(b) total substances	25	25	25
Selenium	10	10	10
Tetrachloroethenes—
(a) individual substance	50	50	50
(b) total substances	25	25	10
Trichloroethenes—
(a) individual substance	50	50	50
(b) total substances	25	25	10
Trihalomethanes—
(a) individual substance	25	25	25
(b) total substances	25	25	10

PART 6 E+W+S Monitoring obligations relating to radon

Representative surveys E+W+S

22.— (1) Each food authority must undertake representative surveys to determine the scale and nature of likely exposure to radon originating from different types of groundwater sources and wells in different geological areas within its area.

(2) The representative surveys must be designed in such a way that underlying parameters determining the likely exposure to radon, including the geology and hydrology of the area, the radioactivity of the rock types and soil types within the area and the type of wells within the area, can be identified and used to determine whether any source or well within the food authority’s area is in an area of likely high exposure to radon.

Monitoring obligation E+W+S

23.   Each food authority must monitor the concentration of radon in any water in its area to which this Schedule applies unless an exemption from monitoring under paragraph 24 is in force.

Exemption E+W+S

24.— (1) A food authority is not required to monitor the concentration of radon in any water in its area if—

(a) on the basis of an assessment of representative surveys, monitoring data and such other information that it considers to be reliable, it is satisfied that the activity concentration of radon in the water does not exceed 100 Bq/l and has decided that it is unlikely to do so for at least five years beginning with the day after the day on which it comes to that decision (“assessment decision”),

(b) it notifies the Secretary of State of its assessment decision and provides the Secretary of State with a copy of the representative surveys, monitoring data and any other information that the authority took into account in coming to that decision,

(c) it notifies the Secretary of State that, on the basis of its assessment decision, the authority has decided not to monitor the activity concentration of radon in the water for a period of five years beginning with the day after the day on which the notification is submitted to the Secretary of State, and

(d) in a case where sub-paragraph (2) applies, the food authority is satisfied that the activity concentration of radon in the water is unlikely to exceed 100 Bq/l for a period of five years beginning with the day after the day on which the food authority submits the notification under paragraph (c).

(2) This sub-paragraph applies where a notification under sub-paragraph (1)(c) is submitted more than three months after the day after the day on which a food authority makes an assessment decision under sub-paragraph (1)(a).

(3) A notification submitted by a food authority under sub-paragraph (1) may relate to all or some of the water in its area to which this Schedule applies.

(4) The exemption from monitoring provided for in sub-paragraph (1) lapses after a period of five years beginning with the day after the day on which the food authority submits the notification referred to in sub-paragraph (1)(c).

(5) But the exemption lapses immediately if the food authority becomes aware (by whatever means) at any time during the five year exemption period that the activity concentration of radon in the water exceeds 100 Bq/l or it has reason to suspect that the activity concentration of radon in the water may exceed 100 Bq/l.

Analysis of sample E+W+S

25.— (1) Where it is necessary under paragraph 23 for a food authority to monitor any water in its area to which this Schedule applies, the food authority must analyse a sample of the water to determine whether the activity concentration of radon in the water in that sample exceeds 100 Bq/l.

(2) The food authority must analyse the sample using a method of analysis that is capable of measuring the activity concentration of radon in the water with a level of detection not exceeding 10 Bq/l.

(3) The limit of detection for a method of analysis relating to the activity concentration of radon must be calculated in accordance with ISO Standard ISO 11929:2010(en) entitled “Determination of the characteristic limits (decision threshold, detection limit and limits of the confidence interval) for measurements of ionizing radiation - Fundamentals and application” published by the International Organization for Standardization on 24th February 2010, with probabilities of errors of the first and second kind of 0.05 each.

(4) In relation to the limit of detection, the uncertainty of measurement must be calculated and reported as complete standard uncertainties, or as expanded standard uncertainties with an expansion factor of 1.96, in accordance with ISO/IEC Guide 98-3:2008 (JCGM/WG1/100) entitled “Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)” published by the International Organization for Standardization on 30th September 2008, as amended by—

(a) ISO/IEC Guide 98-3:2008/Suppl 1:2008 (JCGM/WG1/101) entitled “Propagation of distributions using a Monte Carlo method” published by the International Organization for Standardization on 20th November 2010, and

(b) ISO/IEC Guide 98-3:2008/Suppl 2:2011 (JCGM/WG1/102) entitled “Extension to any number of output quantities” published by the International Organization for Standardization on 9th November 2011.

Action following the result of analysis E+W+S

26.— (1) This paragraph applies if the result of an analysis of a sample of water carried out by a food authority under paragraph 25, or under any other provision of this Schedule, detects an activity concentration of radon exceeding 100 Bq/l.

(2) If an activity concentration of radon exceeding 1,000 Bq/l is detected in a sample of water, the food authority must take action under paragraph 57 (remedial action).

(3) If an activity concentration of radon exceeding 100 Bq/l but not exceeding 1,000 Bq/l is detected in a sample of water (“Sample X”), the food authority must—

(a) take and analyse an extra sample of the water as soon as reasonably practicable after the result of Sample X is detected to determine the activity concentration of radon in the extra sample;

(b) if the food authority considers it appropriate to do so, continue taking and analysing extra samples of the water to determine the activity concentration of radon in those samples at such intervals and for such period as the food authority, taking into account the provisions of sub-paragraphs (4) to (6), considers appropriate.

(4) The food authority must, disregarding the result of Sample X, determine the average of the activity concentration of radon in the water for such 12 month period as the authority considers appropriate (whether the 12 month period used by the food authority for the purpose of its monitoring programme or some other 12 month period) on the basis of—

(a) the results of the analyses of samples of the water carried out before the determination of the result of Sample X,

(b) the result of the analysis of the extra sample under sub-paragraph (3)(a), and

(c) where extra samples are taken under sub-paragraph (3)(b), the results of the analyses of those extra samples.

(5) No further action by the food authority is required if the outcome of the determination under sub-paragraph (4) is that the average of the activity concentration of radon in the water for the relevant 12 month period does not exceed 100 Bq/l.

(6) The food authority must take action under paragraph 57(1) (remedial action) if the outcome of the determination under sub-paragraph (4) is that the average of the activity concentration of radon in the water for the relevant 12 month period exceeds 100 Bq/l.

(7) Sub-paragraphs (3) to (6) do not apply if the food authority is of the opinion that—

(a) even if it took extra samples under sub-paragraph (3) to enable it to determine the activity concentration of radon in those extra samples, it would have insufficient results from previous determinations relating to the activity concentration of radon in the water to enable it to make the determination required by sub-paragraph (4) within such period as the food authority considers to be reasonable, or

(b) for some other reason, the result of such a determination under sub-paragraph (4), based on the results of those extra samples and previous determinations, may give a distorted result.

(8) Where an activity concentration of radon exceeding 100 Bq/l but not exceeding 1,000 Bq/l is detected in a sample of water and, by virtue of sub-paragraph (7), sub-paragraphs (3) to (6) do not apply, a food authority must take action under paragraph 57(1).

Taking of samples: reduced frequency E+W+S

27.— (1) A food authority may, from time to time, decide to reduce the frequency at which it takes and analyses samples of any water in its area under paragraph 25 to determine the activity concentration of radon in the water where—

(a) the result of the analysis of the last sample of the water carried out by the food authority shows that the activity concentration of radon in the water does not exceed 100 Bq/l,

(b) that result, taken together with the results of such other analyses of the water previously carried out by the food authority as it considers relevant to its decision, show that the activity concentration of radon in the water is stable, and

(c) the authority is satisfied that the change in the monitoring arrangements will not increase any risk to human health.

(2) A food authority that has made a decision under sub-paragraph (1) to reduce the frequency at which it takes samples of any water, may decide at any time to start taking samples of the water again at the frequency provided for in the table in Part 3 or, in accordance with sub-paragraph (1), at some other reduced frequency.

Treated bottled drinking water E+W+S

28.   The provisions of this Part, except for paragraph 27, apply to bottled drinking water that has been treated to reduce the level of radionuclides in the water in the same way as it applies to water that has not been treated in that way.

PART 7 E+W+S Monitoring obligations relating to tritium

Monitoring obligation E+W+S

29.   Each food authority must monitor the activity concentration of tritium in any water in its area to which this Schedule applies if an anthropogenic source of tritium or other artificial radionuclide is present within the catchment area, unless an exemption from monitoring under paragraph 30 is in force.

Exemption E+W+S

30.— (1) A food authority is not required to monitor the activity concentration of tritium in any water in its area if—

(a) on the basis of an assessment of representative surveys, monitoring data and such other information as it considers to be reliable, it is satisfied that the activity concentration of tritium in the water does not exceed 100 Bq/l and has decided that it is unlikely to do so for at least five years beginning with the day after the day on which it comes to that decision (“assessment decision”),

(b) it notifies the Secretary of State of its assessment decision and provides the Secretary of State with a copy of the representative surveys, monitoring data and any other information that the authority took into account in coming to that decision,

(c) it notifies the Secretary of State that, on the basis of its assessment decision, the authority has decided not to monitor the activity concentration of tritium in the water for a period of five years beginning with the day after the day on which the notification is submitted to the Secretary of State, and

(d) in a case where sub-paragraph (2) applies, the food authority is satisfied that the activity concentration of tritium in the water is unlikely to exceed 100 Bq/l for a period of five years beginning with the day after the day on which the food authority submits the notification under paragraph (c) to the Secretary of State.

(2) This sub-paragraph applies where a notification under sub-paragraph (1)(c) is submitted more than three months after the day after the day on which a food authority makes an assessment decision under sub-paragraph (1)(a).

(3) A notification submitted by a food authority under sub-paragraph (1) may relate to all or some of the water in its area to which this Schedule applies.

(4) The exemption from monitoring provided for in sub-paragraph (1) lapses after a period of five years beginning with the day after the day on which the food authority submits the notification referred to in sub-paragraph (1)(c).

(5) But the exemption lapses immediately if the food authority becomes aware (by whatever means) at any time during the five year exemption period that the activity concentration of tritium in the water exceeds 100 Bq/l or it has reason to suspect that the activity concentration of tritium in the water may exceed 100 Bq/l.

Analysis of sample E+W+S

31.— (1) Where it is necessary under paragraph 29 for a food authority to monitor any water in its area to which this Schedule applies, the food authority must analyse a sample of the water to determine whether the activity concentration of tritium exceeds 100 Bq/l.

(2) The food authority must analyse the sample using a method of analysis that is capable of measuring the activity concentration of tritium in the water with a level of detection not exceeding 10 Bq/l.

(3) The provisions in paragraph 25(3) and (4) (relating to the calculation and reporting of the limit of detection) apply in the same way to the calculation of the limit of detection for a method of analysis used to measure the activity concentration of tritium as they apply to the calculation and reporting of the limit of detection for a method of analysis used to measure the activity concentration of radon.

Action following the results of analysis E+W+S

32.— (1) This paragraph applies if the result of an analysis of a sample of any water carried out by a food authority under paragraph 31, or under any other provision of this Schedule, detects an activity concentration of tritium exceeding 100 Bq/l in that sample (“Sample X”).

(2) The food authority must—

(a) take and analyse an extra sample of the water as soon as reasonably practicable after the result of Sample X is detected by it to determine the activity concentration of tritium in the extra sample,

(b) if the food authority considers it appropriate to do so, continue taking and analysing extra samples of the water to determine the activity concentration of tritium in those samples at such intervals and for such period as the food authority, taking into account sub-paragraphs (3) to (5), considers appropriate,

(c) determine, by analysis, the gross alpha activity and gross beta activity of the water using water from the same sample, and

(d) taking into account such information about likely sources of radioactivity affecting the water as the food authority considers relevant, analyse a sample of the water (whether water from the same sample or from a different sample of the water) to determine whether such other artificial radionuclides as the food authority may consider relevant are present in the water.

(3) The food authority must, disregarding the result of Sample X, determine the average of the activity concentration of tritium in the water for such 12 month period as the authority considers appropriate (whether the 12 month period used by the food authority for the purpose of its monitoring programme or some other 12 month period) on the basis of—

(a) the results of the analyses of samples of the water carried out before the determination of the result of Sample X,

(b) the result of the analysis of the extra sample under sub-paragraph (2)(a), and

(c) where extra samples are [F27 taken] under sub-paragraph (2)(b), the results of the analyses of those extra samples.

(4) No further action by the food authority is required if the outcome of the determination under sub-paragraph (3) is that the average of the activity concentration of tritium in the water for the relevant 12 month period does not exceed 100 Bq/l.

(5) The food authority must take action under paragraph 57(1) (remedial action) if the outcome of the determination under sub-paragraph (3) is that the average of the activity concentration of tritium in the water for the relevant 12 month period exceeds 100 Bq/l.

(6) Sub-paragraphs (2)(a) and (b) and (3) to (5) do not apply if the food authority is of the opinion that—

(a) even if it took extra samples under sub-paragraph (2)(a) and (b) to enable it to determine the activity concentration of tritium in those extra samples, it would have insufficient results from previous determinations relating to the activity concentration of tritium in the water to enable it to make the determination required by sub-paragraph (3) within such period as the food authority considers to be reasonable, or

(b) for some other reason, the result of such a determination under sub-paragraph (3) based on the results of those extra samples and previous determinations may give a distorted result.

(7) Where an activity concentration of tritium exceeding 100 Bq/l is detected in a sample of water and, by virtue of sub-paragraph (6), sub-paragraphs (2)(a) and (b) and (3) to (5) do not apply, the food authority must take action under paragraph 57(1).

(8) Where a determination of the gross alpha activity and gross beta activity must be made by a food authority under sub-paragraph (2)(c), the food authority must apply the provisions of paragraph 38(2) to (8), in the case of gross alpha activity, and paragraph 39(2) to (8), in the case of gross beta activity, in carrying out that determination and deciding what further action, if any, to take.

Textual Amendments

F27 Word in Sch. 12 para. 32(3)(c) inserted (29.3.2019) by The Environment, Food and Rural Affairs (Miscellaneous Amendments etc.) Regulations 2019 (S.I. 2019/526), regs. 1(2), 27(2)(b)

Taking of samples: reduced frequency E+W+S

33.— (1) A food authority may, from time to time, decide to reduce the frequency at which it takes and analyses samples of any water in its area under paragraph 31 to determine the activity concentration of tritium in the water where—

(a) the result of the analysis of the last sample of the water carried out by the food authority shows that the activity concentration of tritium in the water does not exceed 100 Bq/l,

(b) that result, taken together with the results of such other analyses of the water previously carried out by the food authority as it considers relevant to its decision, show that the activity concentration of tritium in the water is stable, and

(c) the authority is satisfied that the change in the monitoring arrangements will not increase any risk to human health.

(2) A food authority which has made a decision under sub-paragraph (1) to reduce the frequency at which it takes samples of water, may decide at any time to start taking samples of the water again at the frequency provided for in the table in Part 3 or, in accordance with sub-paragraph (1), at some other reduced frequency.

Treated bottled drinking water E+W+S

34.   The provisions of this Part, except for paragraph 33, apply to bottled drinking water that has been treated to reduce the level of radionuclides in the water in the same way as it applies to water that has not been treated in that way.

PART 8 E+W+S Monitoring obligations relating to indicative dose

SECTION 1 E+W+S General

Monitoring obligation E+W+S

35.   If a source of artificial or elevated natural radioactivity is present in a food authority’s area, it must monitor the indicative dose for any water in its area to which this Schedule applies unless an exemption from monitoring under paragraph 36 is in force.

Exemption E+W+S

36.— (1) A food authority is not required to monitor the indicative dose for any water in its area to which this Schedule applies if—

(a) on the basis of representative surveys, monitoring data and such other information that it considers to be reliable, it is satisfied that the indicative dose for the water does not exceed 0.10 mSv and has decided that it is unlikely to do so for at least five years beginning with the day after the day on which it comes to that decision (“assessment decision”),

(b) it notifies the Secretary of State of its assessment decision and provides the Secretary of State with a copy of the representative surveys, monitoring data and any other information that the authority took into account in coming to that decision,

(c) it notifies the Secretary of State that, on the basis of its assessment decision, the authority has decided not to monitor the indicative dose for the water for a period of five years beginning with the day after the day on which the notification is submitted to the Secretary of State, and

(d) in a case where sub-paragraph (2) applies, the food authority is satisfied that the indicative dose for the water is unlikely to exceed 0.10 mSv for a period of five years beginning with the day after the day on which the food authority submits the notification under paragraph (c) to the Secretary of State.

(2) This sub-paragraph applies where a notification under sub-paragraph (1)(c) is submitted more than three months after the day after the day on which a food authority makes an assessment decision under sub-paragraph (1)(a).

(3) A notification submitted by a food authority under sub-paragraph (1) may relate to all or some of the water in its area to which this Schedule applies.

(4) The exemption from monitoring provided for in sub-paragraph (1) lapses after a period of five years beginning with the day after the day on which the food authority submits the notification referred to in sub-paragraph (1)(c).

(5) But the exemption lapses immediately if the food authority becomes aware (by whatever means) at any time during the five year exemption period that the indicative dose for the water exceeds 0.10 mSv or it has reason to suspect that the indicative dose for the water may exceed 0.10 mSv.

Screening E+W+S

37.— (1) For the purpose of monitoring the indicative dose for any water in its area to which this Schedule applies, the food authority may use such screening strategy as it considers to be reliable to determine whether it is necessary for it to carry out a paragraph 45 determination for the water, including—

(a) screening by determining the gross alpha activity in a sample,

(b) screening by determining the gross beta activity in a sample,

(c) screening by determining the activity concentration of a single radionuclide in a sample, or

(d) screening by determining the activity concentration of two or more radionuclides in a sample.

(2) A food authority, in deciding which radionuclide to analyse for the purpose of screening under sub-paragraph (1)(c), and which radionuclides to analyse for the purpose of screening under sub-paragraph (1)(d), must take into account all information available to the authority that it considers relevant relating to likely sources of radioactivity that may affect the water.

Screening by determining gross alpha activity E+W+S

38.— (1) This paragraph applies where a food authority decides to screen any water under paragraph 37(1)(a) (screening of gross alpha activity) to determine whether it is necessary for the authority carry out a paragraph 45 determination for the water.

(2) The food authority must analyse a sample of water to determine whether the gross alpha activity in a sample is less than 0.1 Bq/l.

(3) Where the gross alpha activity detected in a sample does not exceed 0.1 Bq/l, the food authority may assume that the indicative dose for the water does not exceed 0.10 mSv.

(4) Where sub-paragraph (3) applies, the food authority does not need to carry out any further analysis for the purpose of carrying out a paragraph 45 determination for the water, unless it knows from other sources of information that specific radionuclides are present in the water that mean that the indicative dose for the water is likely to exceed 0.10 mSv.

(5) Where the gross alpha activity detected in a sample exceeds 0.1 Bq/l, the food authority must determine, by analysis, the activity concentration of such other radionuclides in the water (using water from the same sample or another sample of the water) as the food authority believes or suspects may be present in the water, taking into account such information about likely sources of radioactivity affecting the water as the food authority considers relevant.

(6) For the purpose of this paragraph, the food authority may set an alternative screening level for gross alpha activity in relation to any water that it is monitoring—

(a) if it is satisfied that, if set at the alternative level that it proposes, the indicative dose for the water will not exceed 0.10 mSv, and

(b) if called upon to do so by the Secretary of State, it can demonstrate to the Secretary of State that, at that alternative screening level, the indicative dose for the water will not exceed 0.10 mSv.

(7) When determining the gross alpha activity in a sample of water for the purpose of this paragraph, the food authority must analyse the sample using a method of analysis that is capable of detecting gross alpha activity in the sample at a level of detection not exceeding 0.04 Bq/l.

(8) The provisions in paragraph 25(3) and (4) (relating to the calculation and reporting of the limit of detection) apply in the same way to the calculation of the limit of detection for a method of analysis used to measure gross alpha activity as they apply to the calculation and reporting of the limit of detection for a method of analysis used to measure the activity concentration of radon.

Screening by determining gross beta activity E+W+S

39.— (1) This paragraph applies where a food authority decides to screen any water under paragraph 37(1)(b) (screening of gross beta activity) to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water.

(2) The food authority must analyse a sample of the water to determine whether the gross beta activity in the sample is less than 1.0 Bq/l.

(3) Where the gross beta activity detected in a sample does not exceed 1.0 Bq/l, the food authority may assume that the indicative dose for the water does not exceed 0.10 mSv.

(4) Where sub-paragraph (3) applies, the food authority does not need to carry out any further analysis for the purpose of carrying out a paragraph 45 determination for the water, unless it knows from other sources of information that specific radionuclides are present in the water that mean that the indicative dose for the water is likely to exceed 0.10 mSv.

(5) Where the gross beta activity of a sample exceeds 1.0 Bq/l, the food authority must determine, by analysis, the activity concentration of such other radionuclides in the water (using water from the same sample or from another sample of the water) as the food authority believes or suspects may be present in the water, taking into account such information about likely sources of radioactivity affecting the water as the food authority considers relevant.

(6) For the purpose of this paragraph, the food authority may set an alternative screening level for gross beta activity in relation to any water that it is monitoring—

(a) if it is satisfied that, if set at the alternative level that it proposes, the indicative dose for the water will not exceed 0.10 mSv, and

(b) if called upon to do so by the Secretary of State, it can demonstrate to the Secretary of State that, at that alternative screening level, the indicative dose for the water will not exceed 0.10 mSv.

(7) When determining the gross beta activity in a sample of water for the purpose of this paragraph, the food authority must analyse the sample using a method of analysis that is capable of detecting gross beta activity in the sample at a level of detection not exceeding 0.4 Bq/l.

(8) The provisions in paragraph 25(3) and (4) (relating to the calculation and reporting of the limit of detection) apply in the same way to the calculation of the limit of detection for a method of analysis used to measure gross beta activity as they apply to the calculation and reporting of the limit of detection for a method of analysis used to measure the activity concentration of radon.

Screening based on analysis relating to one radionuclide E+W+S

40.— (1) This paragraph applies where a food authority decides to screen any water under paragraph 37(1)(c) by determining the activity concentration of one radionuclide in the water to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water.

(2) The food authority must analyse a sample of the water to determine whether the activity concentration of the relevant radionuclide in the sample exceeds 20% of its derived concentration.

(3) Where the activity concentration of the radionuclide in the sample does not exceed 20% of its derived concentration, the food authority may assume that the indicative dose for the water does not exceed 0.10 mSv.

(4) Where sub-paragraph (3) applies, the food authority does not need to carry out any further analysis for the purpose of carrying out a paragraph 45 determination for the water.

(5) Where the activity concentration of the relevant radionuclide in the sample exceeds 20% of its derived concentration, the food authority must determine, by analyses, the activity concentration of such other radionuclides in the water (using water from the same sample or from another sample of the water) as the food authority believes or suspects may be present in the water, taking into account such information about likely sources of radioactivity affecting the water as the food authority considers relevant and the result of any analysis carried out by it under paragraph 32(2)(d).

Screening based on analysis relating to more than one radionuclide E+W+S

41.— (1) This paragraph applies where a food authority decides to screen any water under paragraph 37(1)(d) by determining the activity concentration of more than one radionuclide in the water (“the relevant radionuclides”) to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water.

(2) The food authority must analyse a sample of the water to determine whether, in relation to each of the relevant radionuclides, the activity concentration of any of the relevant radionuclides in the sample exceeds 20% of its derived concentration.

(3) Where the activity concentration of each of the relevant radionuclides in a sample is analysed and none of them are found to be present in the sample at an activity concentration that exceeds 20% of the derived concentration that applies to them, the food authority may assume that the indicative dose for the water does not exceed 0.10 mSv.

(4) Where sub-paragraph (3) applies, the food authority does not need to carry out any further analysis for the purpose of carrying out a paragraph 45 determination for the water.

(5) Where the food authority screens a sample of water for more than one radionuclide and the activity concentration of any one or more of those radionuclides in the sample exceeds 20% of the derived concentration that applies to it or them, the food authority must determine, by analyses, the activity concentration of such other radionuclides in the water (using water from the same sample or from another sample of the water) as the food authority believes or suspects may be present in the water, taking into account such information about likely sources of radioactivity affecting the water as the food authority considers relevant and the result of any analysis carried out by it under paragraph 32(2)(d).

Stopping or reducing the frequency of sampling: screening for indicative dose E+W+S

42.— (1) In relation to screening for indicative dose, a food authority may, from time to time, decide to stop taking samples for screening purposes, or to take such samples at a reduced frequency, where—

(a) it is satisfied that only naturally occurring radionuclides are present in the water,

(b) the result of the analysis of the last sample of the water carried out by the food authority for screening purposes shows that—

(i) where screening has been carried out under paragraph 38, the gross alpha activity in the water did not exceed 0.1 Bq/l,

(ii) where screening has been carried out under paragraph 39, the gross beta activity in the water did not exceed 1.0 Bq/l, or

(iii) where screening has been carried out under paragraph 40 or 41, the activity concentration of any radionuclide in the water analysed for the purpose of that screening did not exceed 20% of its derived concentration,

(c) in a case where the results of the analyses of previous samples taken by the food authority for screening purposes are available and the food authority considers them to be relevant to its decision, the results of the analyses of those samples, taken together with the result of the analysis of the last sample, show that—

(i) where screening has been carried out under paragraph 38, the gross alpha activity in the water is stable,

(ii) where screening has been carried out under paragraph 39, the gross beta activity in the water is stable, or

(iii) where screening has been carried out under paragraph 40 or 41, the activity concentration of any radionuclide analysed for the purpose of that screening is stable, and

(d) the authority is satisfied that the change in the monitoring arrangements will not increase any risk to human health.

(2) Where a food authority has made a decision under sub-paragraph (1) to stop taking samples of water for the purpose of screening under paragraph 38, 39, 40 or 41 but a change occurs in relation to the supply of the water that the food authority believes is likely to influence the activity concentration of radionuclides in the water, the food authority must—

(a) take and analyse a sample of the water using one of the screening methods specified in paragraph 37(1), or

(b) take and analyse a sample of the water and use the results of that analysis to make a paragraph 45 determination for the water.

(3) A food authority which has made a decision under sub-paragraph (1) to stop taking samples of any water, or to reduce the frequency at which it takes samples of the water, may at any time decide to start taking samples of the water again at the frequency provided for in the table in Part 3 or, in accordance with sub-paragraph (1), at some other reduced frequency.

Analysis of sample E+W+S

43.— (1) Where sub-paragraph (2) applies, a food authority must, taking into account such information about likely sources of radioactivity affecting the water as the authority considers relevant, analyse a sample of the water to determine—

(a) which radionuclides are present in the water, and

(b) in relation to each radionuclide found to be present in the water (including radionuclides found to be present in the water as the result of an analysis carried out by it under paragraph 32(2)(d)), the activity concentration at which the radionuclide is present in the water.

(2) This sub-paragraph applies where a food authority is obliged under paragraph 35 to monitor any water in its area to which this Schedule applies and—

(a) the food authority has not carried out any screening during the relevant period under paragraph 38, 39, 40 or 41, and

(b) the water is not water to which a decision to stop taking samples for screening purposes is in force under paragraph 42.

(3) When analysing a sample of water for the purpose of this Part to determine the presence and activity concentration of a radionuclide specified in the first column of the table in Section 2 (minimum levels of detection), the food authority must analyse the sample using a method of analysis that is capable of detecting the activity concentration of the relevant radionuclide at a level of detection not exceeding that specified in the second column of the table, as read, in the case of Ra-228, with the additional provisions specified in the third column of the table.

(4) The provisions in paragraph 25(3) and (4) (relating to the calculation and reporting of the limit of detection) apply in the same way to the calculation of the limit of detection for a method of analysis used to measure the activity concentration of a radionuclide specified in the first column of the table in Section 2 as they apply to the calculation and reporting of the limit of detection for a method of analysis used to measure the activity concentration of radon.

Obligation to make an indicative dose determination E+W+S

44.— (1) A food authority must make a paragraph 45 determination for any water in its area to which this Schedule applies if—

(a) it has not carried out any screening of the water under paragraph 38, 39, 40 or 41 and the obligation does not arise during a period in which a decision made under paragraph 42 to stop taking samples for screening purposes applies,

(b) it has carried out such screening and a determination made under paragraph 38(5), 39(5), 40(5) or 41(5) detected the presence of a radionuclide in the water at an activity concentration that exceeds 20% of its derived concentration, or

(c) a food authority decides to comply with paragraph 42(2) by taking and analysing a sample of the water and using the results of that analysis to make a paragraph 45 determination for the water.

(2) Sub-paragraph (1) does not apply if the obligation arises during a period in which a decision made under paragraph 47 to stop taking samples for the purpose of carrying out a paragraph 45 determination applies.

Determination relating to indicative dose E+W+S

45.— (1) This paragraph applies where it is necessary under paragraph 44 for a food authority to make a determination relating to whether the indicative dose for any water in its area to which this Schedule applies exceeds 0.10 mSv.

(2) The food authority must use the formula in sub-paragraph (3) to make a determination relating to the indicative dose for the water by—

(a) carrying out the calculation in sub-paragraph (4) for each radionuclide that the food authority has found, by analysis, to be present in the water, and

(b) adding together the results of all the calculations done under paragraph (a).

(3) For the purposes of sub-paragraph (2), the formula is—

(4) For the purpose of sub-paragraph (2)(a), the calculation is Ci(obs) ÷ Ci(der).

(5) For the purpose of the formula in sub-paragraph (3) and the calculation in sub-paragraph (4)—

(a) Ci(obs) is the activity concentration (observed concentration) at which a radionuclide has been found, by analysis, to be present in the water expressed in becquerels per litre, and

(b) Ci(der) is the derived concentration for that radionuclide expressed in becquerels per litre.

(6) For the purpose of the formula in sub-paragraph (3), n is the number of radionuclides the food authority has found, by analysis, to be present in the water.

(7) Any non-integer numbers resulting from the calculation carried out under sub-paragraph (2), as read with sub-paragraphs (3) and (4), must be taken into account in calculating and making a determination under this paragraph.

Action following the result of a paragraph 45 determination E+W+S

46.— (1) If a paragraph 45 determination for any water produces a result that does not exceed 1, the indicative dose for the water is to be considered as not exceeding 0.10 mSv and no further investigation by the food authority is required.

(2) If a paragraph 45 determination for any water produces a result that exceeds 1 (“Indicative Dose Determination X”), sub-paragraphs (3) to (7) apply to such water.

(3) The food authority must—

(a) take and analyse an extra sample of the water as soon as reasonably practicable after the result of Indicative Dose Determination X is known and use the result of the analysis of that sample to carry out another paragraph 45 determination for the water;

(b) if the food authority considers it appropriate to do so taking into account the determination made under paragraph (a), continue taking and analysing extra samples of the water, and use the results of those analyses to carry out further paragraph 45 determinations for the water, at such intervals and for such period as the food authority (taking into account the provisions of sub-paragraphs (4) to (6)) considers appropriate.

(4) The food authority must, disregarding the determination of Indicative Dose Determination X, determine the average of the indicative dose determinations for the water for such 12 month period as the authority considers appropriate (whether the 12 month period used by the food authority for the purpose of its monitoring programme or some other 12 month period) on the basis of—

(a) the results of paragraph 45 determinations relating to the water carried out before the determination of Indicative Dose Determination X,

(b) the result of the extra paragraph 45 determination for the water carried out under sub-paragraph (3)(a), and

(c) where any extra paragraph 45 determinations for the water are carried out under sub-paragraph (3)(b), the results of those extra determinations.

(5) No further action by the food authority is required if the outcome of the determination under sub-paragraph (4) is that the average of the indicative dose determinations for the water for the relevant 12 month period does not exceed 1.

(6) The food authority must take action under paragraph 57(1) (remedial action) if the outcome of the determination under sub-paragraph (4) is that the average of the indicative dose determinations for the water for the relevant 12 month period exceeds 1.

(7) Sub-paragraphs (2) to (6) do not apply if the food authority is of the opinion that—

(a) even if it took extra samples under sub-paragraph (3) to enable it to make extra paragraph 45 determinations under that sub-paragraph, it would have insufficient results from previous paragraph 45 determinations for the water to enable it to make the determination required by sub-paragraph (4) within such period as the food authority considers to be reasonable, or

(b) for some other reason, the result of such a determination under sub-paragraph (4), based on the results of those extra samples and the previous paragraph 45 determinations, may give a distorted result.

(8) Where the paragraph 45 determination for a sample of water exceeds 1 and, by virtue of sub-paragraph (7), sub-paragraphs (2) to (6) do not apply, the food authority must take action under paragraph 57(1).

(9) For the purposes of the determination required under sub-paragraph (4), any non-integer numbers resulting from the calculation carried out by a food authority under paragraph 45(2), as read with sub-paragraphs (3) and (4) of that paragraph, must be taken into account in determining whether the result of the determination of the average of the indicative dose for the water for the relevant 12 month period exceeds 1.

Stopping or reducing the frequency of sampling: indicative dose E+W+S

47.— (1) A food authority may, from time to time, decide to stop taking samples for the purpose of carrying out a paragraph 45 determination for any water, or to take such samples at a reduced frequency, where—

(a) it is satisfied that only naturally occurring radionuclides are present in the water,

(b) the result of the last paragraph 45 determination for the water carried out by the food authority produces a result that does not exceed 1,

(c) in a case where the results of previous paragraph 45 determinations for the water are available and the food authority considers them to be relevant to its decision, the average of the results of those determinations produce a result that does not exceed 1, and

(d) the authority is satisfied that the change in the monitoring arrangements will not increase any risk to human health.

(2) Where a food authority has made a decision under sub-paragraph (1) to stop taking samples of water for the purpose of carrying out a paragraph 45 determination for the water but a change occurs in relation to the supply of the water that the food authority believes is likely to influence the concentration of radionuclides in the water, a food authority must—

(a) take and analyse a sample of the water using one of the screening methods specified in paragraph 37, or

(b) take and analyse a sample of the water and use the results of that analysis to make a paragraph 45 determination for the water.

(3) A food authority which has made a decision under sub-paragraph (1) to stop taking samples of any water, or to reduce the frequency at which it takes samples of the water, for the purpose of making paragraph 45 determinations for any water in its area may at any time decide to start taking samples of the water again at the frequency provided for in the table in Part 3 or, in accordance with sub-paragraph (1), at some other reduced frequency.

Treated bottled drinking water E+W+S

48.   The provisions of this Part, except for paragraph 47, apply to bottled drinking water that has been treated to reduce the level of radionuclides in the water in the same way as it applies to water that has not been treated in that way.

SECTION 2 E+W+S Minimum levels of detection

Radionuclides	Limit of detection – Bq/l	Additional provision
U-238	0.02
U-234	0.02
Ra-226	0.04
Ra-228	0.02	The limit of detection in the second column only applies to the initial screening relating to the indicative dose for a new water source. If initial analysis indicates that it is not plausible that Ra-228 will exceed 20% of its derived concentration, the food authority may increase the minimum limit of detection to 0.08 Bq/l for routine Ra-228 nuclide specific measurements, until a recheck is required following a change in the supply of the water that the food authority believes may influence the activity concentration of Ra-228 in the water. The food authority may increase the minimum level of detection back to 0.08 Bq/l again following the result of any recheck if the result of the analysis carried out in relation to that determines that the concentration of Ra-228 in the water does not exceed 20% of its derived concentration.
Pb-210	0.02
Po-210	0.01
C-14	20
Sr-90	0.4
Pu-239/Pu-240	0.04
Am-241	0.06
Co-60	0.5
Cs-134	0.5
Cs-137	0.5
I-131	0.5

SECTION 3 E+W+S Interpretation

Derived concentration E+W+S

49.— (1) In this Part, “derived concentration” in relation to a radionuclide specified in the first column of the following table, means the derived concentration of the radionuclide specified in the second column of that table.

Radionuclide	Derived concentration - Bq/l
U-238	3.0
U-234	2.8
Ra-226	0.5
Ra-228	0.2
Pb-210	0.2
Po-210	0.1
C-14	240
Sr-90	4.9
Pu-239/Pu-240	0.6
Am-241	0.7
Co-60	40
Cs-134	7.2
Cs-137	11
I-131	6.2

(2) In this Part, “derived concentration” in relation to a radionuclide that is not specified in the first column of the table in sub-paragraph (1) means the derived concentration of the radionuclide expressed in becquerels per litre and calculated using the following formula—

(3) For the purpose of the formula in sub-paragraph (2) “ICRP dose coefficient mSv” means the number of millisieverts per becquerel represented by the dose coefficient for an adult for the relevant radionuclide specified in the last column of the table in Annex F (effective dose coefficients for ingestion of radionuclides for members of the public) to ICRP Publication 119 entitled “Compendium of Dose Coefficients based on ICRP Publication 60” published in Volume 41 of Supplement 1 2012 of the Annals of the ICRP on behalf of the International Commission on Radiological Protection by Elsevier and approved by the Commission in October 2011 (ISBN 978-1-4557-5430-4).

PART 9 E+W+S Monitoring obligations relating to indicator parameters

SECTION 1 E+W+S Parametric concentrations and values for indicator parameters

Parameter	Parametric concentration or value	Units of measurement	Further provision	Additional requirements
Aluminium	200	µg/l
Ammonium	0.50	mg/l
Chloride	250	mg/l		The water must not be aggressive.
Clostridium perfringens and spores of Clostridium perfringens	0	number/100ml	This parameter only needs to be checked if the water originates from, or is influenced by, surface water.
Colour	Acceptable to consumers and no abnormal change
Conductivity	2,500	µS cm-1 at 20°C		The water must not be aggressive.
Hydrogen ion concentration	9.5	pH units		The pH of the water must not be lower than 4.5. The water must not be aggressive.
Iron	200	µg/l
Manganese	50	µg/l
Odour	Acceptable to consumers and no abnormal change
Oxidisability	5.0	mg/l O2	This parameter does not need to be checked if total organic carbon is analysed.
Sulphate	250	mg/l		The water must not be aggressive.
Sodium	200	mg/l
Taste	Acceptable to consumers and no abnormal change
Colony Count 22° C	No abnormal change
Coliform bacteria	0	number/250ml
Total organic carbon	No abnormal change		This parameter does not need not be checked for supplies of less than 10,000m3 a day.
Turbidity	Acceptable to consumers and no abnormal change

SECTION 2 E+W+S Monitoring obligations

Analysis of sample E+W+S

50.— (1) Each food authority must monitor the concentration or value (as the case may be) of each of the parameters specified in the first column of the table in Section 1 in water in its area to which this Schedule applies by analysing a sample of the water to determine whether—

(a) the concentration of, or value for, the parameter in the sample exceeds the concentration of, or value for, that parameter specified in the second column of the table—

(i) as measured, where relevant, by reference to the unit of measurement specified in the third column of the table, and

(ii) as read, in relation to a parameter specified in the first column of the table for which there is an additional requirement specified in the fourth column of the table, with the provision relating to the need to check the parameter specified in the fourth column of the table, and

(b) in relation to a parameter specified in the first column of the table for which there is an additional requirement specified in the fifth column of the table, the water complies with that additional requirement.

(2) For the purpose of the determination required by sub-paragraph (1), the food authority must analyse the sample—

(a) in the case of Clostridium perfringens, and spores of Clostridium perfringens, using the method of analysis in BS EN ISO 14189:2016 entitled “Water quality — Enumeration of Clostridium perfringens — Method using membrane filtration (ISO 14189:2013)” (ISBN 978 0 580 92184 1), as amended by a corrigendum issued on 31st August 2016;

(b) in the case of coliform bacteria, using the method of analysis in—

(i) BS EN ISO 9308-1:2014+A1:2017 entitled “Water quality — Enumeration of Escherichia coli and coliform bacteria. Part 1: Membrane filtration method for waters with low bacterial background flora (ISO 9308-1:2014)” (ISBN 978 0 580 92379 1) published by the BSI on 31st October 2014, as amended on 28th February 2017, or

(ii) BS EN ISO 9308-2:2014 entitled “Water quality — Enumeration of Escherichia coli and coliform bacteria. Part 2: Most probable number method” (ISBN 978 0 580 84023 4) published by the BSI on 30th November 2013, as amended by a corrigendum issued on 30th June 2014;

(c) in the case of each of the other indicator parameters, using a method of analysis that complies with Section 3.

Clostridium perfringens E+W+S

51.   In a case where a food authority determines that a sample of water contains any Clostridium perfringens, or spores of Clostridium perfringens, the food authority must investigate the water supply to determine whether there is any potential danger to human health arising from the presence in the water of pathogenic microorganisms.

Uncertainty of measurement E+W+S

52.   A food authority must not use the uncertainty of measurement percentage specified in the second column of the table in Section 4 (which is concerned with whether a method of analysis complies with minimum performance characteristics) as an additional tolerance when determining whether the concentration of a parameter specified in the first column of the table in Section 1 in a sample of water exceeds the concentration for that parameter specified in the second column of the table in Section 1.

SECTION 3 E+W+S Method of analysis

Method of analysis E+W+S

53.   In relation to a parameter specified in the first column of the table in Section 1—

(a) where there is a method of analysis that meets minimum performance characteristics that can be used by a food authority to analyse a sample for the purpose of making a determination in relation to that parameter under paragraph 50, the food authority must analyse the sample using that method of analysis (or using any one of them in a case where more than one method of analysis meets minimum performance characteristics);

(b) where there is no such method of analysis, the food authority must analyse a sample under paragraph 50 using the best available technique not entailing excessive cost.

Minimum performance characteristics E+W+S

54.— (1) For the purpose of paragraph 53(a), a method of analysis for a parameter specified in the first column of the table in Section 4 (minimum performance characteristics for a method of analysis) is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—

(a) is capable of measuring values equal to the parametric concentration of that parameter with a limit of quantification of 30% or less of the relevant parametric concentration,

(b) has an uncertainty of measurement that does not exceed the percentage of the parametric concentration for the parameter specified in the second column of the table in Section 4, as read with any further provision relating to the calculation of the uncertainty of measurement specified in the third column of the table, and

(c) in the case of total organic carbon, complies with the requirement specified in the fourth column of the table.

(2) For the purpose of sub-paragraph (1)(b), the performance criterion for uncertainty of measurement (k = 2) for a parameter specified in the first column of the table in Section 4 is not less than the percentage specified in the second column of the table of the concentration or value for the parameter specified in the second column of the table in Section 1.

(3) A method of analysis for hydrogen ion concentration pH is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—

(a) is capable of measuring hydrogen ion concentration pH equal to 4.5 pH with a limit of quantification of 30% or less, and

(b) has an uncertainty of measurement that does not exceed 0.2 of a pH unit.

(4) For the purpose of sub-paragraph (3)(b), the performance criterion for uncertainty of measurement (k = 2) for hydrogen ion concentration pH is not less than 0.2 of a pH unit.

(5) Unless otherwise specified in the third column of the table in Section 4, food authorities must estimate uncertainty of measurement for a parameter specified in the first column of the table at the level of the concentration for the parameter specified in the second column of the table in Section 1.

(6) Where a method of analysis that complies with the requirements of sub-paragraph (1) is used to determine whether the concentration of a parameter specified in the first column of the table in Section 4 exceeds the concentration specified for that parameter in the second column of the table in Section 1, the result of the analysis carried out using that method of analysis must be expressed using at least the same number of significant figures as the number of significant figures used to specify that parametric concentration in the second column of the table in Section 1.

Alternative minimum performance characteristics E+W+S

55.— (1) For the purpose of paragraph 53(a), until the end of 31st December 2019, a method of analysis for a parameter specified in the first column of the table in Section 5 (alternative minimum performance characteristics for a method of analysis that may be used until the end of 31st December 2019) is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—

(a) is capable of measuring concentrations with a trueness not less than the percentage of the parametric concentration specified in the second column of the table,

(b) is capable of measuring concentrations with a precision not less than the percentage of the parametric concentration specified in the third column of the table, and

(c) has a limit of detection that does not exceed the percentage of the parametric concentration specified in the fourth column of the table.

(2) For the purpose of paragraph 53(a), until the end of 31st December 2019, a method of analysis for hydrogen ion concentration pH is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that is capable of measuring hydrogen ion concentration pH with—

(a) a trueness not less than 0.2 of a pH unit, and

(b) a precision not less than 0.2 of a pH unit.

(3) “Precision” is the same for the purposes of this paragraph, and the table in Section 5, as it is in paragraph 20(2).

(4) “Limit of detection” is the same for the purposes of this paragraph, and the table in Section 5, as it is in paragraph 20(3).

SECTION 4 E+W+S Minimum performance characteristics for a method of analysis

Parameters	Uncertainty of measurement - percentage of the parametric concentration	Other requirements relating to the uncertainty of measurement	Other requirements
Aluminium	25
Ammonium	40
Chloride	15
Conductivity	20
Iron	30
Manganese	30
Oxidisability	50
Sodium	15
Sulphate	15
Total organic carbon	30	The uncertainty of measurement must be estimated at the level of 3 mg/l of the total organic carbon.	BS EN 1484: 1997 entitled “Water analysis —Guidelines for the determination of total organic carbon (TOC) and dissolved organic carbon (DOC)” (ISBN 0 580 28372 0) published by the BSI on 15th October 1997 must be used.
Turbidity	30	The uncertainty of measurement must be estimated at the level of 1.0 nephelometric turbidity unit in accordance with BS EN ISO 7027-1:2016 entitled “Water quality — Determination of turbidity. Part 1: Quantitative methods (ISO 7027-1: 2016)” (ISBN 978 0 580 81961 2) published by the BSI on 31st July 2016.

SECTION 5 E+W+S Alternative minimum performance characteristics for a method of analysis that may be used until the end of 31st December 2019

Parameters	Trueness - percentage of the parametric concentration	Precision -percentage of the parametric concentration	Limit of detection - percentage of the parametric concentration
Aluminium	10	10	10
Ammonium	10	10	10
Chloride	10	10	10
Conductivity	10	10	10
Iron	10	10	10
Manganese	10	10	10
Oxidisability	25	25	10
Sodium	10	10	10
Sulphate	10	10	10
Turbidity	25	25	25

PART 10 E+W+S Delegation of tasks by a food authority

SECTION 1 E+W+S Delegation of tasks

Delegation E+W+S

56.— (1) A food authority may delegate a task specified in the first column of the table in Section 2 (tasks that may be delegated) on an one-off or occasional basis or for such duration as may, from time to time, be agreed between the food authority and the person to whom the task is to be delegated.

(2) Any arrangement entered into under sub-paragraph (1) must provide that the delegate must comply with any provision in this Schedule relating to the exercise of that task, including any provision relating to—

(a) the taking of samples,

(b) the frequency (if relevant, taking into account the duration of the arrangement) at which the samples are to be taken,

(c) the method of analysis that must be used to analyse samples, including any minimum performance characteristics that apply to the selection of a method of analysis,

(d) the calculation of the limit of detection,

(e) the use of uncertainty of measurement percentages,

(f) the validation and documenting of the methods of analysis used, and

(g) the use of quality management practices.

(3) In relation to a task specified in the first column of the table in Section 2 for which there is an entry in the second column of the table, any arrangement entered into under sub-paragraph (1) must provide that—

(a) the food authority must, where specified in the second column of the table, provide the delegate with the instructions needed to carried out the task, and

(b) the delegate must carry out the delegated task on the basis specified in the second column of that table.

(4) A food authority must not enter into an arrangement under sub-paragraph (1) unless—

(a) it is satisfied that the task will be carried out promptly by a person competent to perform it, and

(b) it has made arrangements with the delegate to ensure that—

(i) where the result of an analysis indicates that the concentration or value of any parameter has been exceeded, the delegate will communicate the result of the analysis to the food authority immediately after determining the result, and

(ii) in every other case, the delegate will communicate the result of the analysis to the food authority within 28 days beginning with the day after the day on which it has determined the result.

SECTION 2 E+W+S Tasks that may be delegated

Task that may be delegated	Basis of delegation (where relevant)
The task of taking samples under paragraph 4 of all waters in a food authority’s area to which this Schedule applies or of such of those waters as are specified in the arrangement
The task of taking samples under paragraph 5 of all waters in a food authority’s area to which this Schedule applies or of such of those waters as are specified in the arrangement
The task of analysing samples of water under paragraph 7(1) (microbiological parameters)
The task of analysing samples of water under paragraph 8(1) (chemical parameters)
The task of analysing samples of water under paragraph 13 (other parameters)	The food authority must provide the delegate with instructions relating to the identity of the property, element, substance or organism that is to be checked and the delegate must analyse the samples in accordance with those instructions.
The task of analysing samples of water under paragraph 25 (radon)
The task of taking an extra sample, or extra samples, of water under paragraph 26(3) (radon)	In a case where the food authority has provided general instructions to the delegate in relation to the application of paragraph 26(3) concerning the number of samples to be taken and, in a case where more than one extra sample may need to be taken, the period during which extra samples are to be taken (“the specified matters”), the delegate must take an extra sample, or extra samples, in accordance with those instructions. In a case where the food authority has not provided general instructions to the delegate in relation to the specified matters, the food authority must provide the delegate with specific instructions concerning those matters at the time an extra sample falls to be taken under paragraph 26(3) and the delegate must take the samples in accordance with those instructions.
The task of analysing an extra sample, or extra samples, of water under paragraph 26(3) (radon)
The task of analysing samples of water under paragraph 31 (tritium)
The task of taking an extra sample, or extra samples, of water under paragraph 32(2) (tritium)	In a case where the food authority has provided general instructions to the delegate in relation to the application of paragraph 32(2) concerning the number of samples to be taken and, in a case where more than one extra sample may need to be taken, the period during which extra samples are to be taken (“the specified matters”), the delegate must take an extra sample, or extra samples, in accordance with those instructions. In a case where the food authority has not provided general instructions to the delegate in relation to the specified matters, the food authority must provide the delegate with specific instructions concerning those matters at the time an extra sample falls to be taken under paragraph 32(2) and the delegate must take the samples in accordance with those instructions.
The task of analysing an extra sample, or extra samples, of water under paragraph 32(2)(a) and (b) (tritium)
The task of measuring gross alpha activity and gross beta activity in a sample under paragraph 32(2)(c)
The task of analysing samples of water under paragraph 32(2)(d) (relating to the determination of the presence of artificial radionuclides in the water), and the taking of such extra sample, or extra samples, of the water as may be needed for that purpose
The task of analysing samples of water under paragraph 38(2) (screening by determining gross alpha activity)
The task of analysing samples of water under paragraph 38(5) (relating to the determination of the presence and concentration of certain radionuclides in the water), and the taking of such extra sample, or extra samples, of the water as may be needed for that purpose	The food authority must provide the delegate with instructions specifying the radionuclides in the sample [F28 for which] analysis must be carried out by the delegate and the delegate must analyse the samples in accordance with those instructions.
The task of analysing samples of water under paragraph 39(2) (screening by determining gross beta activity)
The task of analysing samples of water under paragraph 39(5) (relating to the determination of the presence and concentration of certain radionuclides in the water) and the taking of such extra sample, or extra samples, of the water as may be needed for that purpose	The food authority must provide the delegate with instructions specifying the radionuclides in the sample [F28 for which] analysis must be carried out by the delegate and the delegate must analyse the samples in accordance with those instructions.
The task of analysing samples of water under paragraph 40(2) (screening based on analysis relating to one radionuclide)
The task of analysing samples of water under paragraph 40(5) (relating to the determination of the presence and concentration of certain radionuclides in the water) and taking such extra sample, or extra samples, of the water as may be needed for that purpose	The food authority must provide the delegate with instructions specifying the radionuclides in the sample [F28 for which] analysis must be carried out by the delegate and the delegate must analyse the samples in accordance with those instructions.
The task of analysing samples of water under paragraph 41(2) (screening based on analyses relating to more than one radionuclide)
The task of analysing samples of water under paragraph 41(5) (relating to the determination of the presence and concentration of certain radionuclides in water) and taking such extra sample, or extra samples, of the water as may be needed for that purpose	The food authority must provide the delegate with instructions specifying the radionuclides in the sample [F28 for which] analysis must be carried out by the delegate and the delegate must analyse the samples in accordance with those instructions.
The task of analysing samples of water under paragraph 43(1) (relating to the determination of the presence, and concentration of, certain radionuclides in water)	The food authority must provide the delegate with instructions specifying the radionuclides in the sample [F28 for which] analysis must be carried out by the delegate and the delegate must analyse the samples in accordance with those instructions.
The task of carrying out a paragraph 45 determination (relating to indicative dose)
The task of taking an extra sample, or extra samples of water under paragraph 46(3) (further sampling required following an indicative dose determination)	In a case where the food authority has provided general instructions to the delegate in relation to the application of paragraph 46(3) concerning the number of samples to be taken and, in a case where more than one extra sample may need to be taken, the period during which extra samples are to be taken (“the specified matters”), the delegate must take an extra sample, or extra samples, in accordance with those instructions. In a case where the food authority has not provided general instructions to the delegate in relation to the specified matters, the food authority must provide the delegate with specific instructions concerning those matters at the time an extra sample falls to be taken under paragraph 46(3) and the delegate must take the samples in accordance with those instructions.
The task of analysing an extra sample, or extra samples, of water under paragraph 46(3)
The task of analysing samples of water under paragraph 50(1) (indicator parameters)

Textual Amendments

F28 Words in Sch. 12 Pt. 10 substituted (29.3.2019) by The Environment, Food and Rural Affairs (Miscellaneous Amendments etc.) Regulations 2019 (S.I. 2019/526), regs. 1(2), 27(2)(c)

PART 11 E+W+S Remedial action

Remedial action E+W+S

57.— (1) If, taking into account the provisions of this Schedule, a food authority determines that water in its area to which this Schedule applies contains a parameter specified in the first column of the table in Part 4 of Schedule 2 that exceeds (or is to be considered as exceeding) the activity concentration or value specified in the second column of the table (as measured by reference to the unit of measurement specified in the third column of the table), the food authority must—

(a) immediately investigate the non-compliance in order to identify the cause,

(b) assess whether the non-compliance poses a risk to human health that requires action,

(c) require the proprietor of the food business bottling the water to take remedial action as soon as possible to restore the quality of the water if the authority considers that it is necessary for such action to be taken to protect human health,

(d) notify the general public of the risks and remedial action taken, and

(e) advise the general public on any additional precautionary measures that may be needed for the protection of human health in respect of radioactive substances.

(2) Sub-paragraph (1)(a) and (b) do not apply where paragraph 26(2) applies.]

Regulation 22

[F29 SCHEDULE 13 E+W+S Application and modification of provisions of the Act

Textual Amendments

F29 Sch. 13 inserted (6.4.2018) by The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018 (S.I. 2018/352), reg. 1(1), Sch. 2

Provision of the Act	Modifications
Section 2 (extended meaning of “sale” etc.)	In subsection (1), for “this Act” substitute “the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
	In subsection (2), for “This Act” substitute “The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
Section 3 (presumptions that food intended for human consumption)	In subsection (1), for “this Act” substitute “the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
Section 10(1) and (2) (improvement notices)	For subsection (1), substitute— “(1)  If an authorised officer of an enforcement authority has reasonable grounds for believing that a person is failing to comply with any provision specified in subsection (1A) or is carrying out either a fluoride removal treatment or an ozone-enriched air treatment that has a disinfectant action, the authorised officer may, by a notice served on that person (in this Act referred to as an “improvement notice”)— (a) state the officer’s grounds for believing that the person is failing to comply with the relevant provision; (b) specify the matters which constitute the person’s failure so to comply; (c) specify the measures which, in the officer’s opinion, the person must take in order to secure compliance; and (d) require the person to take those measures, or measures that are at least equivalent to them, within such period (not being less than 14 days) as may be specified in the notice. (1A)  The provisions referred to in subsection (1) are— (a) any of regulations 4 to 15 of the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007; and (b) any of the following provisions of Commission Regulation (EU) No 115/2010 laying down the conditions for use of activated alumina for the removal of fluoride from natural mineral waters and spring waters— (i) Article 1(2) (requirement that fluoride removal treatment must be performed in accordance with the technical requirements set out in the Annex to Commission Regulation (EU) No 115/2010); (ii) the first sentence of Article 2 (requirement that the release of residues into natural mineral water or spring water as a result of fluoride removal treatment be as low as technically feasible according to best practices and not pose a risk to public health); (iii) the second sentence of Article 2 (requirement for operators to implement and monitor the critical processing steps set out in the Annex to Commission Regulation (EU) No 115/2010); (iv) Article 3(1) (requirement that the application of any fluoride removal treatment be notified to the competent authorities at least three months prior to use); and (v) Article 4 (requirement that the label on natural mineral water or spring water subjected to fluoride removal treatment include specified information in proximity to the statement of the analytical composition).”.
Section 20 (offences due to fault of another person)	For “any of the preceding provisions of this Part” substitute “section 10(2), as applied by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
Section 21(1) and (5) (defence of due diligence)	In subsection (1), for “any of the preceding provisions of this Part (in this section referred to as “the relevant provision”)” substitute “section 10(2), as applied by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
Section 29 (procurement of samples)	After “under section 32 below”, insert “as applied and modified by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”. In paragraph (d), for the words from “this Act” to “under it” substitute “the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
Section 30(6) and (8) (which relates to evidence of certificates given by a food analyst or examiner)	In subsection (8), for “this Act” substitute “the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
Section 32(1) to (7) (powers of entry)	In subsection (1), for paragraphs (a) to (c) substitute— “(a) subject to paragraph (c), to enter any premises within the authority’s area for the purpose of ascertaining whether there is, or has been, on the premises a contravention of any of the following provisions of Commission Regulation (EU) No 115/2010 laying down the conditions for use of activated alumina for the removal of fluoride from natural mineral waters and spring waters— (i) Article 1(2) (requirement that fluoride removal treatment must be performed in accordance with the technical requirements set out in the Annex to Commission Regulation (EU) No 115/2010); (ii) the first sentence of Article 2 (requirement that the release of residues into natural mineral water or spring water as a result of fluoride removal treatment be as low as technically feasible according to best practices and not pose a risk to public health); (iii) the second sentence of Article 2 (requirement for operators to implement and monitor the critical processing steps set out in the Annex to Commission Regulation (EU) No 115/2010); (iv) Article 3(1) (requirement that the application of any fluoride removal treatment be notified to the competent authorities at least three months prior to use); and (v) Article 4 (requirement that the label on natural mineral water or spring water subjected to fluoride removal treatment include specified information in proximity to the statement of the analytical composition); and (b) to enter any business premises, whether within or outside the authority’s area, for the purpose of ascertaining whether there is on the premises any evidence of any contravention within that area of any of the provisions set out in paragraph (a); (c) but any premises which are a private dwelling-house (whether in whole or part) may only be entered for the purposes of paragraph (a) on production of a warrant which authorises such entry and, unless the warrant provides otherwise, admission to any premises used wholly as a private dwelling-house shall not be demanded;”. For subsection (2) substitute— “(2) If a justice of the peace, on sworn information in writing, is satisfied that there is reasonable ground for entry into any private dwelling-house for any purpose mentioned in subsection (1)(a) the justice may, by signed warrant, authorise the authorised officer to enter the private dwelling-house, if necessary by reasonable force.”.”. In subsection (6)(a), for the words from “this Act” to “under it” substitute “the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
Section 33 (obstruction etc. of officers)	In subsection (1), for “this Act” in each place those words occur substitute “the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.
Section 35(1) and (2) (punishment of offences)	In subsection (1), after “section 33(1) above” insert “, as applied and modified by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007,”.
	After subsection (1), insert— “(1A) A person guilty of an offence under section 10(2), as applied by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007, is liable, on summary conviction, to a fine.”.
	In subsection (2), for “any other offence under this Act” substitute “an offence under section 33(2), as applied by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007,”.
Section 36 (offences by bodies corporate)	In subsection (1), for “this Act” substitute “section 10(2), as applied by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007,”.
Section 36A(offences by Scottish partnerships)	For “this Act” substitute “section 10(2), as applied by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007,”.
Section 37(1) and (6) (appeals)	For subsection (1) substitute— “(1)  Any person who is aggrieved by a decision of an authorised officer of an enforcement authority to serve an improvement notice under section 10(1), as applied and modified by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007, may appeal to the First-tier Tribunal.”.
	In subsection (6)— (a) for “(3) or (4)” substitute “(1)”; and (b) in paragraph (a), for a “magistrates’ court or to the sheriff” substitute “the First-tier Tribunal”.
Section 39 (appeals against improvement notices)	For subsection (1) substitute— “(1)  On an appeal against an improvement notice served under section 10(1), as applied and modified by regulation 22 of, and Schedule 13 to, the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007, the First-tier Tribunal may either cancel or affirm the notice and, if it affirms it, may do so either in its original form or with such modifications as the First-tier Tribunal may in the circumstances think fit.”.
	In subsection (3), omit “for want of prosecution”.
Section 44 (protection of officers acting in good faith)	For “this Act” in each place those words occur substitute “the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007”.]