The Meaford Gas Fired Generating Station Order 2016

Detailed design

3.—(1) The authorised development must be carried out in accordance with—

(a) the approved plans listed in Table 1 below inclusive of any limits of deviation; and

(b) any other plans, drawings, documents, details, schemes, statements or strategies which are approved by the relevant planning authority pursuant to any requirement (as the same may be amended by approval of the relevant planning authority pursuant to requirement 19(1))—

Table 1

works plans	Submission document reference number 2.3
access rights of way plan	Submission document reference number 2.4

(2) The authorised development must not exceed the maximum parameters specified in Table 2 and Table 3 below (as the same may be amended by approval of the relevant planning authority under requirement 19(1))—

Table 2

(1) Element of authorised development	(2) Maximum height (metres) above a site level of approximately 99 metres AOD	(3) Maximum width (metres)	(4) Maximum length (metres)	(5) Other parameters
Gas turbine building (part of numbered work 1A)	25 metres	45 metres	60 metres	Maximum height 124m AOD
Each Heat Recovery Steam Generator Building (part of numbered work 1A)	35 metres	13 metres	25 metres	Maximum height AOD 134 metres
Each exhaust gas emission flue stack (part of numbered work 1A)	50 metres	–	–	Maximum height AOD 149 metres Maximum diameter 6.5 metres
Steam turbine building (part of numbered work 1A)	21 metres	26 metres	45 metres	–
Air cooled condenser (part of numbered work 1A)	26 metres	48 metres	48 metres	–
Switchgear room (part of numbered work 1A)	5 metres	10 metres	15 metres	–
Raw/fire water storage tank (part of numbered work 1B)	20 metres	–	–	Maximum diameter 15 metres
Each water storage tank (part of numbered work 1B)	20 metres	–	–	Maximum diameter 5 metres
Water treatment system (part of numbered work 1B)	10 metres	25 metres	20 metres	–
Workshop (part of numbered work 1B)	10 metres	20 metres	30 metres	–
Natural gas pressure regulating installation (PRI) (part of numbered work 1B)	5 metres	25 metres	35 metres	–
Administration/ control building (part of numbered work 1C)	10 metres	10 metres	20 metres	–
Heat network interface building (part of numbered work 1C)	15 metres	20 metres	30 metres	–
Each transformer compound (part of numbered work 1D)	8 metres	15 metres	15 metres	–
132kV switchyard (part of work numbered 1D)	10 metres	42 metres	72 metres	–
Perimeter fencing (part of numbered work 1E)	2.5 metres	–	770 metres	–

Table 3

(1) Element of authorised development	(2) Maximum height (metres) above the existing site level	(3) Maximum width (metres)	(4) Maximum length (metres)	(5) Other parameters
Above Ground Installation (numbered work 2A)	2.5 metres	13 metres	13 metres	–
Pipeline inspection gauge facility (part of numbered work 2A)	1.6 metres	1 metre	5.5 metres	–
Perimeter fencing (part of numbered work 2A)	2.5 metres	–	52 metres	–
Pipeline support plinth including crown of pipe (part of numbered work 2B)	2 metres	0.8 metres	1.4 metres	–

(3) To the extent that design objectives relating to any numbered work are set out in the design objectives statement, that numbered work must be designed substantially in accordance with the relevant design objective set out therein.

(4) Numbered works 1, 2 and 4 may not commence until, for that numbered work, written details have been submitted to and approved by the relevant planning authority (in consultation with the National Trust regarding the external appearance and the colour of all permanent buildings and structures) concerning—

(a) the siting, design, external appearance, dimensions and floor levels of all permanent buildings and structures; and

(b) the colour, materials and surface finishes of the pipeline and all permanent buildings and structures.

(5) The details to be submitted for approval under sub-paragraph (4) must include appropriately scaled plans and sectional drawings.