Directive 2004/108/EC of the European Parliament and of the Council (repealed)Show full title

CHAPTER II U.K. APPARATUS

Article 7 U.K. Conformity assessment procedure for apparatus

Compliance of apparatus with the essential requirements referred to in Annex I shall be demonstrated by means of the procedure described in Annex II (internal production control). However, at the discretion of the manufacturer or of his authorised representative in the Community, the procedure described in Annex III may also be followed.

Article 8 U.K. ‘CE’ marking

1. Apparatus whose compliance with this Directive has been established by means of the procedure laid down in Article 7 shall bear the ‘CE’ marking which attests to that fact. The affixing of the ‘CE’ marking shall be the responsibility of the manufacturer or his authorised representative in the Community. The ‘CE’ marking shall be affixed in accordance with Annex V.

2. Member States shall take the necessary measures to prohibit the affixing to the apparatus, or to its packaging, or to the instructions for its use, of marks which are likely to mislead third parties in relation to the meaning and/or graphic form of the ‘CE’ marking.

3. Any other mark may be affixed to the apparatus, its packaging, or the instructions for its use, provided that neither the visibility nor the legibility of the ‘CE’ marking is thereby impaired.

4. Without prejudice to Article 10, if a competent authority establishes that the ‘CE’ marking has been unduly affixed, the manufacturer or his authorised representative in the Community shall bring the apparatus into conformity with the provisions concerning the ‘CE’ marking under conditions imposed by the Member State concerned.

Article 9 U.K. Other marks and information

1. Each apparatus shall be identified in terms of type, batch, serial number or any other information allowing for the identification of the apparatus.

2. Each apparatus shall be accompanied by the name and address of the manufacturer and, if he is not established within the Community, the name and address of his authorised representative or of the person in the Community responsible for placing the apparatus on the Community market.

3. The manufacturer shall provide information on any specific precautions that must be taken when the apparatus is assembled, installed, maintained or used, in order to ensure that, when put into service, the apparatus is in conformity with the protection requirements set out in Annex I, point 1.

4. Apparatus for which compliance with the protection requirements is not ensured in residential areas shall be accompanied by a clear indication of this restriction of use, where appropriate also on the packaging.

5. The information required to enable apparatus to be used in accordance with the intended purpose of the apparatus shall be contained in the instructions accompanying the apparatus.

Article 10 U.K. Safeguards

1. Where a Member State ascertains that apparatus bearing the ‘CE’ marking does not comply with the requirements of this Directive, it shall take all appropriate measures to withdraw the apparatus from the market, to prohibit its placing on the market or its putting into service, or to restrict the free movement thereof.

2. The Member State concerned shall immediately inform the Commission and the other Member States of any such measure, indicating the reasons and specifying, in particular, whether non-compliance is due to:

(a) failure to satisfy the essential requirements referred to in Annex I, where the apparatus does not comply with the harmonised standards referred to in Article 6;

(b) incorrect application of the harmonised standards referred to in Article 6;

(c) shortcomings in the harmonised standards referred to in Article 6.

3. The Commission shall consult the parties concerned as soon as possible, following which it shall inform the Member States whether or not it finds the measure to be justified.

4. Where the measure referred to in paragraph 1 is attributed to a shortcoming in harmonised standards, the Commission, after consulting the parties, shall, if the Member State concerned intends to uphold the measure, bring the matter before the Committee and initiate the procedure laid down in Article 6(3) and (4).

5. Where the non-compliant apparatus has been subject to the conformity assessment procedure referred to in Annex III, the Member State concerned shall take appropriate action in respect of the author of the statement referred to in Annex III, point 3, and shall inform the Commission and the other Member States accordingly.

Article 11 U.K. Decisions to withdraw, prohibit or restrict the free movement of apparatus

1. Any decision taken pursuant to this Directive to withdraw apparatus from the market, prohibit or restrict its placing on the market or its putting into service, or restrict the free movement thereof, shall state the exact grounds on which it is based. Such decisions shall be notified without delay to the party concerned, who shall at the same time be informed of the remedies available to him under the national law in force in the Member State in question and of the time limits to which such remedies are subject.

2. In the event of a decision as referred to in paragraph 1, the manufacturer, his authorised representative, or any other interested party shall have the opportunity to put forward his point of view in advance, unless such consultation is not possible because of the urgency of the measure to be taken as justified in particular with respect to public interest requirements.

Article 12 U.K. Notified bodies

1. Member States shall notify the Commission of the bodies which they have designated to carry out the tasks referred to in Annex III. When determining the bodies to be designated, Member States shall apply the criteria laid down in Annex VI.

Such notification shall state whether the bodies are designated to carry out the tasks referred to in Annex III for all apparatus covered by this Directive, and/or the essential requirements referred to in Annex I or whether the scope of designation is limited to certain specific aspects and/or categories of apparatus.

2. Bodies which comply with the assessment criteria established by the relevant harmonised standards shall be presumed to comply with the criteria set out in Annex VI covered by such harmonised standards. The Commission shall publish in the Official Journal of the European Union the references of those standards.

3. The Commission shall publish in the Official Journal of the European Union a list of notified bodies. The Commission shall ensure that the list is kept up to date.

4. If a Member State finds that a notified body no longer meets the criteria listed in Annex VI, it shall inform the Commission and the other Member States accordingly. The Commission shall withdraw the reference to that body from the list referred to in paragraph 3.