- Latest available (Revised)
- Original (As adopted by EU)
Directive 2009/142/EC of the European Parliament and of the Council of 30 November 2009 relating to appliances burning gaseous fuels (codified version) (Text with EEA relevance)
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).
EU Directives are published on this site to aid cross referencing from UK legislation. Since IP completion day (31 December 2020 11.00 p.m.) no amendments have been applied to this version.
THE EUROPEAN PARLIAMENT AND THE COUNCIL OF THE EUROPEAN UNION,
Having regard to the Treaty establishing the European Community, and in particular Article 95 thereof,
Having regard to the proposal from the Commission,
Having regard to the opinion of the European Economic and Social Committee(1),
Acting in accordance with the procedure laid down in Article 251 of the Treaty(2),
Whereas:
(1) Council Directive 90/396/EEC of 29 June 1990 on the approximation of the laws of the Member States relating to appliances burning gaseous fuels(3) has been substantially amended(4). In the interests of clarity and rationality the said Directive should be codified.
(2) Member States are responsible for ensuring the health and safety on their territory of their people and, where appropriate, of domestic animals and goods in relation to the hazards arising out of the use of appliances burning gaseous fuels.
(3) In certain Member States, mandatory provisions define in particular the safety level required of appliances burning gaseous fuels by specifying design, operating characteristics and inspection procedures. These mandatory provisions do not necessarily lead to different safety levels from one Member State to another but do, by their disparity, hinder trade within the Community.
(4) Different conditions as regards types of gas and supply pressures are in force in the Member States. These conditions are not harmonised because each Member State’s energy supply and distribution situation is peculiar to it.
(5) Community law provides - by way of derogation from one of the fundamental rules of the Community, namely the free movement of goods - that obstacles to movement within the Community resulting from disparities in national legislation relating to the marketing of products must be accepted in so far as such obstacles can be recognised as being necessary to satisfy mandatory requirements. Therefore, the harmonisation of legislation in the present case should be limited to the provisions necessary to satisfy both the mandatory and essential requirements regarding safety, health and energy conservation in relation to gas appliances. These requirements should replace the national provisions in this matter because they are essential requirements.
(6) The maintenance or improvement of the level of safety attained in Member States constitutes one of the essential aims of this Directive and of safety as defined by the essential requirements.
(7) The essential safety and health requirements should be observed in order to ensure that appliances burning gaseous fuels are safe. Energy conservation is considered essential. These requirements should be applied with discernment to take account of the state of the art at the time of construction.
(8) This Directive should therefore only contain essential requirements. To facilitate proof of conformity with the essential requirements, it is necessary to have harmonised standards at Community level in particular as to the construction, operation and installation of appliances burning gaseous fuels so that products complying with them may be assumed to conform to the essential requirements. These standards, harmonised at Community level, are drawn up by private bodies and must remain non-mandatory texts. For that purpose the European Committee for Standardisation (CEN), the European Committee for Electrotechnical Standardisation (Cenelec) and the European Telecommunications Standards Institute (ETSI) are recognised as the competent bodies for the adoption of harmonised standards in accordance with the general guidelines for cooperation between the Commission, the European Free Trade Association (EFTA) and those three bodies signed on 28 March 2003(5). ‘Harmonised standard’ means a technical specification (European standard or harmonisation document) adopted by CEN, Cenelec or ETSI or by two or three of those bodies upon a remit from the Commission in accordance with Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations and of rules on Information Society services(6) and the above mentioned general guidelines for cooperation.
(9) The Council has adopted a series of Directives designed to remove technical barriers to trade in accordance with the principles established in Resolution of 7 May 1985 on a new approach to technical harmonisation and standards(7); each of these Directives provides for the affixing of the CE marking. The Commission, in its Communication of 15 June 1989 on a global approach to certification and testing(8), proposed that common rules be drawn up concerning a CE marking with a single design. The Council, in its Resolution of 21 December 1989 on a global approach to conformity assessment(9), approved as a guiding principle the adoption of a consistent approach such as this with regard to the use of the CE marking. The two basic elements of the new approach which should be applied are the essential requirements and the conformity assessment procedures.
(10) A check on compliance with the relevant technical requirements is necessary in order to provide effective protection for users and third parties. The existing certification procedures differ from one Member State to another. In order to avoid multiple inspections, which are in effect barriers to the free movement of appliances burning gaseous fuels, arrangements should be made for the mutual recognition of certification procedures by the Member States. In order to facilitate mutual recognition of certification procedures, harmonised Community procedures and the criteria for appointing the bodies responsible for carrying out these procedures should be set up.
(11) The Member States’ responsibility on their territory for safety, health and energy conservation covered by the essential requirements should be recognised in a safeguard clause providing for an adequate Community procedure.
(12) The addressees of any decision taken under this Directive should be informed of the reasons for such a decision and the legal remedies available to them.
(13) This Directive is without prejudice to the obligations of the Member States relating to the time-limits for transposition into national law and application of the Directives in Annex VI, Part B,
HAVE ADOPTED THIS DIRECTIVE:
1.This Directive shall apply to appliances and fittings.
Appliances specifically designed for use in industrial processes carried out on industrial premises shall be excluded from its scope.
2.For the purposes of this Directive the following definitions shall apply:
(a)‘appliances’ means appliances burning gaseous fuels used for cooking, heating, hot water production, refrigeration, lighting or washing and having, where applicable, a normal water temperature not exceeding 105 °C. Forced draught burners and heating bodies to be equipped with such burners shall also be considered as appliances;
(b)‘fittings’ means safety devices, controlling devices or regulating devices and sub-assemblies, other than forced draught burners and heating bodies to be equipped with such burners, separately marketed for trade use and designed to be incorporated into an appliance burning gaseous fuel or assembled to constitute such an appliance;
(c)‘gaseous fuel’ means any fuel which is in a gaseous state at a temperature of 15 °C under a pressure of 1 bar.
3.For the purposes of this Directive, an appliance is said to be ‘normally used’ when it is:
(a)correctly installed and regularly serviced in accordance with the manufacturer’s instructions;
(b)used with a normal variation in the gas quality and a normal fluctuation in the supply pressure; and
(c)used in accordance with its intended purpose or in a way which can be reasonably foreseen.
1.Member States shall take all necessary steps to ensure that appliances may be placed on the market and put into service only if, when normally used, they do not compromise the safety of persons, domestic animals and property.
2.Member States shall communicate in good time to the other Member States and the Commission all changes to the types of gas and corresponding supply pressures used on their territory which have been communicated in accordance with Article 2(2) of Directive 90/396/EEC.
The Commission shall ensure that this information is published in the Official Journal of the European Union.
Appliances and fittings shall satisfy the essential requirements applicable to them set out in Annex I.
1.Member States may not prohibit, restrict or impede the placing on the market and the putting into service of appliances which comply with this Directive and which bear the CE marking provided for in Article 10.
2.Member States may not prohibit, restrict or impede the placing on the market of fittings accompanied by a certificate as referred to in Article 8(4).
1.Member States shall presume compliance with the essential requirements set out in Annex I of appliances and fittings when they conform to:
(a)the national standards applicable to them implementing the harmonised standards the reference numbers of which have been published in the Official Journal of the European Union;
(b)the national standards applicable to them in so far as, in the areas covered by such standards, no harmonised standards exist.
2.Member States shall publish the reference numbers of the national standards referred to in paragraph 1(a).
They shall communicate to the Commission the texts of their national standards as referred to in paragraph 1(b) which they regard as complying with the essential requirements set out in Annex I.
The Commission shall forward these national standards to the other Member States. In accordance with the procedure provided for in Article 6(2), it shall notify the Member States of those national standards which are presumed to conform with the essential requirements set out in Annex I.
1.Where a Member State or the Commission considers that the standards referred to in Article 5(1) do not entirely meet the essential requirements set out in Annex I, the Commission or the Member State concerned shall bring the matter before the standing committee established under Article 5 of Directive 98/34/EC, hereinafter referred to as ‘the committee’, giving the reasons therefor.
The committee shall deliver an opinion without delay.
In the light of the committee’s opinion, the Commission shall inform the Member States whether or not it is necessary to withdraw those standards from the publications referred to in the first subparagraph of Article 5(2).
2.After receipt of the communication referred to in the second subparagraph of Article 5(2), the Commission shall consult the committee.
Upon receipt of the committee’s opinion, the Commission shall, within one month, inform the Member States whether the national standard(s) in question are to enjoy the presumption of conformity. If they are, the Member States shall publish the reference numbers of those standards.
The Commission shall also publish them in the Official Journal of the European Union.
1.Where a Member State finds that normally used appliances bearing the CE marking might compromise the safety of persons, domestic animals or property, it shall take all appropriate measures to withdraw those appliances from the market and prohibit or restrict their being placed on the market.
The Member State concerned shall immediately inform the Commission of any such measure, indicating the reasons for its decision and, in particular, whether non-compliance is due to:
(a)failure to meet the essential requirements set out in Annex I, where the appliance does not correspond to the standards referred to in Article 5(1);
(b)incorrect application of the standards referred to in Article 5(1);
(c)shortcomings in the standards referred to in Article 5(1) themselves.
2.The Commission shall enter into consultation with the parties concerned as soon as possible. Where, after such consultation, the Commission finds that any measure as referred to in paragraph 1 is justified, it shall immediately so inform the Member State that took the measure and the other Member States.
Where the decision referred to in paragraph 1 is attributed to shortcomings in the standards, the Commission, after consulting the parties concerned, shall bring the matter before the committee within two months if the Member State which has taken the measures intends to maintain them, and shall initiate the procedures referred to in Article 6.
3.Where an appliance which does not comply bears the CE marking, the competent Member State shall take appropriate action against whomsoever has affixed the CE marking and shall inform the Commission and the other Member States thereof.
4.The Commission shall ensure that the Member States are kept informed of the progress and outcome of the procedures.
1.The means of certification of conformity of series-manufactured appliances shall be:
(a)the EC type-examination as referred to in point 1 of Annex II; and
(b)prior to their being placed on the market, at the choice of the manufacturer:
the EC declaration of conformity to type referred to in point 2 of Annex II, or
the EC declaration of conformity to type (guarantee of production quality) referred to in point 3 of Annex II, or
the EC declaration of conformity to type (guarantee of product quality) referred to in point 4 of Annex II, or
EC verification as referred to in point 5 of Annex II.
2.In the case of production of an appliance as a single unit or in small quantities, EC verification by single unit, as referred to in point 6 of Annex II, may be chosen by the manufacturer.
3.After completion of the procedures referred to in paragraphs 1(b) and 2, the CE marking shall be affixed to conforming appliances in accordance with Article 10.
4.The means of certification of conformity referred to in paragraph 1 shall be applied in respect of fittings with the exception of the affixing of the CE marking and, where appropriate, the drawing-up of the declaration of conformity.
A certificate shall be issued declaring the conformity of the fittings with the provisions of this Directive which apply to them and stating their characteristics and how they must be incorporated into an appliance or assembled to assist compliance with the essential requirements applicable to finished appliances set out in Annex I.
The certificate shall be supplied with the fitting.
5.Where the appliances are covered by other Directives dealing with other aspects and specifying the affixing of the CE marking, the latter shall indicate that the appliances are also presumed to conform to the provisions of those Directives.
However, where one or more of these Directives allow the manufacturer, during a transitional period, to choose which arrangements to apply, the CE marking shall indicate conformity to the provisions only of those Directives applied by the manufacturer. In this case, particulars of the Directives applied, as published in the Official Journal of the European Union, must be given in the documents, notices or instructions required by the Directives and accompanying such devices.
6.Records and correspondence relating to the means of certification of conformity shall be drawn up in the official language(s) of the Member State where the body responsible for carrying out these procedures is established or in a language accepted by it.
1.Member States shall notify the Commission and the other Member States of the bodies which they have appointed to carry out the procedures referred to in Article 8 together with the specific tasks which these bodies have been appointed to carry out and the identification numbers assigned to them beforehand by the Commission.
The Commission shall, for information, publish in the Official Journal of the European Union, a list of those bodies, and the identification numbers it has assigned to them and shall ensure that the list is kept up to date.
2.Member States shall apply the criteria set out in Annex V for assessing the bodies to be notified.
Bodies which satisfy the assessment criteria laid down in the applicable harmonised standards shall be presumed to satisfy the criteria set out in that Annex.
3.A Member State which has notified a body must withdraw approval if it finds that the body no longer meets the criteria set out in Annex V. It shall immediately inform the Commission and the other Member States accordingly.
1.The CE marking and the inscriptions set out in Annex III shall be affixed in a visible, easily legible and indelible form to the appliance or to a data plate attached to it. The data plate shall be so designed that it cannot be re-used.
2.The affixing of markings on the appliances which are likely to deceive third parties as to the meaning and form of the CE marking shall be prohibited. Any other marking may be affixed to the appliance or to the data plate provided that the visibility and legibility of the CE marking are not thereby reduced.
Without prejudice to Article 7:
where a Member State establishes that the CE marking has been affixed unduly, the manufacturer or his authorised representative established within the Community shall be obliged to make the product comply as regards the provisions concerning the CE marking and to end the infringement under conditions imposed by that Member State;
where non-compliance continues, the Member State must take all appropriate measures to restrict or prohibit the placing on the market of the appliance in question or to ensure that it is withdrawn from the market in accordance with the procedure laid down in Article 7.
Any decision taken pursuant to this Directive which includes restriction on the placing on the market and/or putting into service of an appliance shall state the precise grounds on which it is based. It shall be notified without delay to the party concerned, who shall at the same time be informed of the legal remedies available to him under the laws in force in the Member State in question and of the time-limits to which such remedies are subject.
Member States shall communicate to the Commission the texts of the provisions of national law which they adopt in the field covered by this Directive.
Directive 90/396/EEC, as amended by the Directive listed in Annex VI, Part A, is repealed, without prejudice to the obligations of the Member States relating to the time-limits for transposition into national law and application of the Directives set out in Annex VI, Part B.
References to the repealed Directive shall be construed as references to this Directive and shall be read in accordance with the correlation table in Annex VII.
This Directive shall enter into force on the twentieth day following its publication in the Official Journal of the European Union.
This Directive is addressed to the Member States.
Done at Brussels, 30 November 2009.
For the European Parliament
The President
J. Buzek
For the Council
The President
B. Ask
The obligations resulting from the essential requirements for appliances in this Annex also apply to fittings where the corresponding risk exists.
be accompanied by technical instructions intended for the installer,
be accompanied by instructions for use and servicing, intended for the user,
bear appropriate warning notices, which must also appear on the packaging.
The instructions and warning notices must be in the official language or languages of the Member States of destination.
the type of gas used,
the gas supply pressure used,
the flow of fresh air required:
for the combustion air supply,
to avoid the formation of dangerous unburned gas mixtures for appliances not fitted with the device referred to in point 3.2.3,
the conditions for the dispersal of combustion products,
for forced draught burners and heating bodies intended to be equipped with such burners, their characteristics, the requirements for assembly, to assist compliance with the essential requirements applicable to finished appliances and, where appropriate, the list of combinations recommended by the manufacturer.
The instructions for installation, adjustment, operation and maintenance must be provided with the fittings concerned.
Appliances which are not fitted with such devices must be used only in areas where there is sufficient ventilation to avoid a dangerous accumulation of unburned gas.
Member States may define on their territory adequate space ventilation conditions for the installation of such appliances, bearing in mind the features peculiar to them.
Large-scale kitchen appliances and appliances powered by gas containing toxic components must be equipped with the aforesaid device.
Appliances must be so constructed that, when used normally:
ignition and re-ignition is smooth,
cross-lighting is assured.
Appliances must be so constructed as to ensure rational use of energy, reflecting the state of the art and taking into account safety aspects.
Without prejudice to the Community rules in this area, materials and components used in the construction of an appliance, which may come into contact with food or water used for sanitary purposes, must not impair their quality.
the name and address of the manufacturer and, if the application is lodged by the authorised representative, his name and address,
a written declaration that the application has not been lodged with any other notified body,
the design documentation, as described in Annex IV.
The type may additionally cover variants of the product provided that those variants do not have different characteristics with respect to types of risk.
examine the design documentation and verify that the type has been manufactured in conformity with the design documentation and identify the elements which have been designed in accordance with the applicable provisions of the standards referred to in Article 5 and the essential requirements of this Directive;
perform, or have performed, the appropriate examinations and/or tests to check whether the solutions adopted by the manufacturer meet the essential requirements where the standards referred to in Article 5 have not been applied;
perform, or have performed, the appropriate examinations and/or tests to check whether the applicable standards have effectively been applied where the manufacturer has chosen to do so, thereby assuring conformity with the essential requirements.
Modifications to the approved type must receive additional approval from the notified body that issued the EC type-examination certificate where such changes affect conformity with the essential requirements or the prescribed conditions for use of the appliance. This additional approval is to be given in the form of an addition to the original EC type-examination certificate.
The application must include:
the quality system documentation,
an undertaking to carry out the obligations arising from the quality system as approved,
an undertaking to maintain the approved quality system to ensure its continuing suitability and effectiveness,
documentation relating to the approved type and a copy of the EC type-examination certificate.
the quality objectives, the organisational structure and responsibilities of management and of their powers with regard to appliance quality,
the manufacturing processes, quality control and quality assurance techniques and systematic actions that will be used,
the examinations and tests that will be carried out before, during and after manufacture and the frequency with which they will be carried out,
the method of monitoring attainment of the required appliance quality and the effective operation of the quality system.
It must notify its decision to the manufacturer and inform the other notified bodies thereof. The notification to the manufacturer must contain the conclusions of the examination, the name and address of the notified body and the reasoned assessment decision in respect of the appliances concerned.
The notified body must examine the proposed modifications and decide whether the modified quality system complies with the relevant provisions or whether reappraisal is necessary. It must notify the manufacturer of its decision. The notification must include the conclusions of the inspection and the reasoned assessment decision.
the quality system documentation,
the quality records, such as inspection reports and test data, calibration data, reports on qualifications of the staff concerned.
The application must include:
the quality system documentation,
an undertaking to carry out the obligations arising from the quality system as approved,
an undertaking to maintain the approved quality system to ensure its continuing suitability and effectiveness,
the documentation relating to the approved type and a copy of the EC type-examination certificate.
All the elements, requirements and provisions adopted by the manufacturer must be documented in a systematic and logical manner in the form of measures, procedures and written instructions. This quality system documentation must permit a uniform interpretation of the quality programmes, plans, manuals and records.
The quality system documentation shall contain, in particular, an adequate description of:
the quality objectives, the organisational structure and responsibilities of management and of their powers with regard to appliance quality,
the checks and tests to be carried out after manufacture,
the method of verifying the effective operation of the quality system.
The notified body must examine the proposed changes and decide whether the amended quality system satisfies the relevant provisions or whether a reassessment is necessary. It must notify the manufacturer of its decision. The notification must contain the conclusions of the inspection and the reasoned assessment decision.
the quality system documentation,
the quality files such as inspection reports and test data, calibration data, report on qualifications of the staff concerned.
Appliances are subject to statistical control by attributes. They should be grouped into identifiable batches consisting of units of a single model manufactured under the same conditions. A batch is examined at random intervals. The appliances constituting a sample are examined individually and appropriate tests, as laid down in the respective standard(s) referred to in Article 5, or equivalent tests are carried out to determine whether the batch is to be accepted or rejected.
A sampling system with the following characteristics is applied:
a level of quality corresponding to a probability of acceptance of 95 %, with a non-conformity percentage of between 0,5 and 1,5 %,
a limit quality corresponding to a probability of acceptance of 5 %, with a percentage of non-conformity of between 5 and 10 %.
Where a batch is rejected, the notified body must take appropriate measures to prevent the placing on the market of that batch. In the event of frequent rejection of batches the notified body may suspend the statistical verification.
The manufacturer may, under the responsibility of the notified body, affix the latter's identification number during the manufacturing process.
The notified body must affix, or cause to be affixed, its identification number to the approved appliance and must draw up a written certificate of conformity concerning the tests carried out.
The design documentation referred to in Annex IV must be made available to the notified body.
The CE marking must be followed by the identification number of the notified body involved in the production control phase.
the manufacturer's name or identification symbol,
the trade name of the appliance,
the type of electrical supply used, if applicable,
the appliance category,
the last two digits of the year in which the CE marking was affixed.
Information needed for installation purposes may be added according to the nature of the appliance.
The various components of the CE marking must have substantially the same vertical dimension, which may not be less than 5 mm.
The design documentation must contain the following information, in so far as is required by the notified body for assessment:
a general description of the appliance,
conceptual designs and manufacturing drawings and diagrams of components, sub-assemblies, circuits, etc.,
descriptions and explanations necessary for the understanding of the above, including the operation of the appliances,
a list of the standards referred to in Article 5, applied in full or in part, and descriptions of the solutions adopted to meet the essential requirements where the standards referred to in Article 5 have not been applied,
test reports,
manuals for installation and use.
Where appropriate, the design documentation must contain the following elements:
attestations relating to the equipment incorporated in the appliance,
attestations and certificates relating to the methods of manufacture and/or inspection and/or monitoring of the appliance,
any other document making it possible for the notified body to improve its assessment.
The notified bodies designated by the Member States must fulfil the following minimum conditions:
availability of personnel and of the necessary means and equipment,
technical competence and professional integrity of personnel,
independence in carrying out tests, preparing reports, issuing certificates and performing the surveillance provided for in this Directive, of management and technical staff in relation to all circles, groups or persons directly or indirectly involved in the field of the appliances,
maintenance of professional secrecy by staff,
possession of civil liability insurance unless that liability is covered by the State under national law.
Fulfilment of the conditions in the first two indents must be periodically verified by the competent authorities of the Member States or by bodies designated by the Member States.
(referred to in Article 14)
Council Directive 90/396/EEC | |
Council Directive 93/68/EEC | only Article 10 |
(referred to in Article 14)
Directive | Time-limit for transposition | Date of application |
---|---|---|
90/396/EEC | 30 June 1991 | 1 January 1992 |
93/68/EEC | 30 June 1994 | 1 January 1995 |
Directive 90/396/EEC | This Directive |
---|---|
Article 1(1), introductory wording | Article 1(1), first subparagraph |
Article 1(1), first and second indents | Article 1(2)(a) and (b) |
Article 1(2) | Article 1(1), second subparagraph |
Article 1(3) | Article 1(2)(d) |
Article 1(4) | Article 1(3) |
Article 2(1) | Article 2(1) |
Article 2(2), first and second sentences | Article 2(2), first subparagraph |
Article 2(2), third sentence | Article 2(2), second subparagraph |
Articles 3 and 4 | Articles 3 and 4 |
Article 5(1)(a), first subparagraph | Article 5(1)(a) |
Article 5(1)(a), second subparagraph | Article 5(2), first subparagraph |
Article 5(1)(b) | Article 5(1)(b) |
Article 5(2), first sentence | Article 5(2), second subparagraph |
Article 5(2), third sentence | Article 5(2), third subparagraph |
Article 6(1), first subparagraph, first sentence | Article 6(1), first subparagraph |
Article 6(1), first subparagraph, second sentence | Article 6(1), second subparagraph |
Article 6(1), second subparagraph | Article 6(1), third subparagraph |
Article 6(2), first sentence | Article 6(2), first subparagraph |
Article 6(2), second sentence | Article 6(2), second subparagraph |
Article 6(2), third sentence | Article 6(2), third subparagraph |
Article 7 | Article 7 |
Article 8(1)(a) | Article 8(1)(a) |
Article 8(1)(b), introductory wording | Article 8(1)(b), introductory wording |
Article 8(1)(b), first to fourth indents | Article 8(1)(b)(i) to (iv) |
Article 8(2) and (3) | Article 8(2) and (3) |
Article 8(4), first subparagraph, first sentence | Article 8(4), first subparagraph |
Article 8(4), first subparagraph, second sentence | Article 8(4), second subparagraph |
Article 8(4), second subparagraph | Article 8(4), third subparagraph |
Article 8(5)(a) | Article 8(5), first subparagraph |
Article 8(5)(b) | Article 8(5), second subparagraph |
Article 8(6) | Article 8(6) |
Articles 9 to12 | Articles 9 to 12 |
Article 13 | — |
Article 14(1) and (2) | — |
Article 14(3) | Article 13 |
— | Article 14 |
— | Article 15 |
Article 15 | Article 16 |
Annexes I to V | Annexes I to V |
— | Annex VI |
— | Annex VII |
Opinion of the European Parliament of 20 October 2009 (not yet published in the Official Journal) and Council Decision of 26 November 2009.
See Annex VI, Part A.
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Geographical Extent: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Show Timeline of Changes: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
This timeline shows the different versions taken from EUR-Lex before exit day and during the implementation period as well as any subsequent versions created after the implementation period as a result of changes made by UK legislation.
The dates for the EU versions are taken from the document dates on EUR-Lex and may not always coincide with when the changes came into force for the document.
For any versions created after the implementation period as a result of changes made by UK legislation the date will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. For further information see our guide to revised legislation on Understanding Legislation.
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: