Commission Delegated Regulation (EU) No 811/2013Show full title

ANNEX V U.K. Technical documentation

1. SPACE HEATERS U.K.

For space heaters, the technical documentation referred to in Article 3(1)(c) shall include:

(a)

the name and address of the supplier;

(b)

a description of the space heater model sufficient for its unambiguous identification;

(c)

where appropriate, the references of the harmonised standards applied;

(d)

where appropriate, the other technical standards and specifications used;

(e)

the identification and signature of the person empowered to bind the supplier;

(f)

technical parameters:

• for boiler space heaters and cogeneration space heaters, the technical parameters set out in Table 7, measured and calculated in accordance with Annex VII;

• for heat pump space heaters, the technical parameters set out in Table 8, measured and calculated in accordance with Annex VII;

• for heat pump space heaters where the information relating to a specific model comprising a combination of indoor and outdoor units has been obtained by calculation on the basis of design and/or extrapolation from other combinations, the details of such calculations and/or extrapolations, and of any tests undertaken to verify the accuracy of the calculations, including details of the mathematical model for calculating the performance of such combinations and details of the measurements taken to verify this model;

(g)

any specific precautions that shall be taken when the space heater is assembled, installed or maintained.

2. COMBINATION HEATERS U.K.

For combination heaters, the technical documentation referred to in Article 3(2)(c) shall include:

(a)

the name and address of the supplier;

(b)

a description of the combination heater model sufficient for its unambiguous identification;

(c)

where appropriate, the references of the harmonised standards applied;

(d)

where appropriate, the other technical standards and specifications used;

(e)

the identification and signature of the person empowered to bind the supplier;

(f)

technical parameters:

• for boiler combination heaters, the technical parameters set out in Table 7, measured and calculated in accordance with Annex VII;

• for heat pump combination heaters, the technical parameters set out in Table 8, measured and calculated in accordance with Annex VII;

• for heat pump combination heaters where the information relating to a specific model comprising a combination of indoor and outdoor units has been obtained by calculation on the basis of design and/or extrapolation from other combinations, the details of such calculations and/or extrapolations, and of any tests undertaken to verify the accuracy of the calculations, including details of the mathematical model for calculating the performance of such combinations and details of the measurements taken to verify this model;

(g)

any specific precautions that shall be taken when the combination heater is assembled, installed or maintained.

Table 7

Technical parameters for boiler space heaters, boiler combination heaters and cogeneration space heaters

a High-temperature regime means 60 °C return temperature at heater inlet and 80 °C feed temperature at heater outlet.
b Low temperature means for condensing boilers 30 °C, for low-temperature boilers 37 °C and for other heaters 50 °C return temperature (at heater inlet).
Model(s): [information identifying the model(s) to which the information relates]
Condensing boiler: [yes/no]
Low-temperatureb boiler: [yes/no]
B11 boiler: [yes/no]
Cogeneration space heater: [yes/no]					If yes, equipped with a supplementary heater: [yes/no]
Combination heater: [yes/no]
Item	Symbol	Value	Unit		Item	Symbol	Value	Unit
Rated heat output	Prated	x	kW		Seasonal space heating energy efficiency	ηs	x	%
For boiler space heaters and boiler combination heaters: Useful heat output					For boiler space heaters and boiler combination heaters: Useful efficiency
At rated heat output and high-temperature regimea	P4	x,x	kW		At rated heat output and high-temperature regimea	η4	x,x	%
At 30 % of rated heat output and low-temperature regimeb	P1	x,x	kW		At 30 % of rated heat output and low-temperature regimeb	η1	x,x	%
For cogeneration space heaters: Useful heat output					For cogeneration space heaters: Useful efficiency
At rated heat output of cogeneration space heater with supplementary heater disabled	PCHP100+Sup0	x,x	kW		At rated heat output of cogeneration space heater with supplementary heater disabled	ηCHP100+Sup0	x,x	%
At rated heat output of cogeneration space heater with supplementary heater enabled	PCHP100+Sup100	x,x	kW		At rated heat output of cogeneration space heater with supplementary heater enabled	ηCHP100+Sup100	x,x	%
For cogeneration space heaters: Electrical efficiency					Supplementary heater
At rated heat output of cogeneration space heater with supplementary heater disabled	ηel,CHP100+Sup0	x,x	%		Rated heat output	Psup	x,x	kW
At rated heat output of cogeneration space heater with supplementary heater enabled	ηel,CHP100+Sup100	x,x	%		Type of energy input
Auxiliary electricity consumption					Other items
At full load	elmax	x,x	kW		Standby heat loss	Pstby	x,x	kW
At part load	elmin	x,x	kW		Ignition burner power consumption	Pign	x,x	kW
In standby mode	PSB	x,xxx	kW		Annual energy consumption	QHE	x	kWh or GJ
					Sound power level, indoors	LWA	x	dB
For combination heaters:
Declared load profile					Water heating energy efficiency	ηwh	x	%
Daily electricity consumption	Qelec	x,xxx	kWh		Daily fuel consumption	Qfuel	x,xxx	kWh
Annual electricity consumption	AEC	x	kWh		Annual fuel consumption	AFC	x	GJ
Contact details	Name and address of the supplier.

Table 8

Technical parameters for heat pump space heaters and heat pump combination heaters

a For heat pump space heaters and heat pump combination heaters, the rated heat output Prated is equal to the design load for heating Pdesignh, and the rated heat output of a supplementary heater Psup is equal to the supplementary capacity for heating sup(Tj).
b If Cdh is not determined by measurement then the default degradation coefficient is Cdh = 0,9.
Model(s): [information identifying the model(s) to which the information relates]
Air-to-water heat pump: [yes/no]
Water-to-water heat pump: [yes/no]
Brine-to-water heat pump: [yes/no]
Low-temperature heat pump: [yes/no]
Equipped with a supplementary heater: [yes/no]
Heat pump combination heater: [yes/no]
Parameters shall be declared for medium-temperature application, except for low-temperature heat pumps. For low-temperature heat pumps, parameters shall be declared for low-temperature application.
Parameters shall be declared for average, colder and warmer climate conditions.
Item	Symbol	Value	Unit		Item	Symbol	Value	Unit
Rated heat output a	Prated	x	kW		Seasonal space heating energy efficiency	ηs	x	%
Declared capacity for heating for part load at indoor temperature 20 °C and outdoor temperature Tj					Declared coefficient of performance or primary energy ratio for part load at indoor temperature 20 °C and outdoor temperature Tj
Tj = – 7 °C	Pdh	x,x	kW		Tj = – 7 °C	COPd or PERd	x,xx or x,x	– or %
Tj = + 2 °C	Pdh	x,x	kW		Tj = + 2 °C	COPd or PERd	x,xx or x,x	– or %
Tj = + 7 °C	Pdh	x,x	kW		Tj = + 7 °C	COPd or PERd	x,xx or x,x	– or %
Tj = + 12 °C	Pdh	x,x	kW		Tj = + 12 °C	COPd or PERd	x,xx or x,x	– or %
Tj = bivalent temperature	Pdh	x,x	kW		Tj = bivalent temperature	COPd or PERd	x,xx or x,x	– or %
Tj = operation limit temperature	Pdh	x,x	kW		Tj = operation limit temperature	COPd or PERd	x,xx or x,x	– or %
For air-to-water heat pumps: Tj = – 15 °C (if TOL < – 20 °C)	Pdh	x,x	kW		For air-to-water heat pumps: Tj = – 15 °C (if TOL < – 20 °C)	COPd or PERd	x,xx or x,x	– or %
Bivalent temperature	Tbiv	x	°C		For air-to-water heat pumps: Operation limit temperature	TOL	x	°C
Cycling interval capacity for heating	Pcych	x,x	kW		Cycling interval efficiency	COPcyc or PERcyc	x,xx or x,x	– or %
Degradation co-efficientb	Cdh	x,x	—		Heating water operating limit temperature	WTOL	x	°C
Power consumption in modes other than active mode					Supplementary heater
Off mode	POFF	x,xxx	kW		Rated heat outputb	Psup	x,x	kW
Thermostat-off mode	PTO	x,xxx	kW
Standby mode	PSB	x,xxx	kW		Type of energy input
Crankcase heater mode	PCK	x,xxx	kW
Other items
Capacity control	fixed/variable				For air-to-water heat pumps: Rated air flow rate, outdoors	—	x	m3/h
Sound power level, indoors/outdoors	LWA	x / x	dB		For water- or brine-to-water heat pumps: Rated brine or water flow rate, outdoor heat exchanger	—	x	m3/h
Annual energy consumption	QHE	x	kWh or GJ
For heat pump combination heater:
Declared load profile	x				Water heating energy efficiency	ηwh	x	%
Daily electricity consumption	Qelec	x,xxx	kWh		Daily fuel consumption	Qfuel	x,xxx	kWh
Annual electricity consumption	AEC	x	kWh		Annual fuel consumption	AFC	x	GJ
Contact details	Name and address of the supplier.

3. TEMPERATURE CONTROLS U.K.

For temperature controls, the technical documentation referred to in Article 3(3)(b) shall include:

(a)

the name and address of the supplier;

(b)

a description of the temperature control model sufficient for its unambiguous identification;

(c)

where appropriate, the references of the harmonised standards applied;

(d)

where appropriate, the other technical standards and specifications used;

(e)

the identification and signature of the person empowered to bind the supplier;

(f)

technical parameters:

• the class of the temperature control;

• the contribution of the temperature control to seasonal space heating energy efficiency in %, rounded to one decimal place;

(g)

any specific precautions that shall be taken when the temperature control is assembled, installed or maintained.

4. SOLAR DEVICES U.K.

For solar devices, the technical documentation referred to in Article 3(4)(b) shall include:

(a)

the name and address of the supplier;

(b)

a description of the solar device model sufficient for its unambiguous identification;

(c)

where appropriate, the references of the harmonised standards applied;

(d)

where appropriate, the other technical standards and specifications used;

(e)

the identification and signature of the person empowered to bind the supplier;

(f)

technical parameters (for pumps in the collector loop if applicable):

• the collector aperture area A_sol in m², to two decimal places;

• the collector efficiency η_col in %, rounded to the nearest integer;

• the energy efficiency class of the solar hot water storage tank, determined in accordance with point 3 of Annex II;

• the standing loss S of the solar hot water storage tank in W, rounded to the nearest integer;

• the storage volume V of the solar hot water storage tank in litres and m³;

• the annual non-solar heat contribution Q_nonsol in kWh in terms of primary energy for electricity and/or in kWh in terms of GCV for fuels, for the load profiles M, L, XL and XXL under average climate conditions, rounded to the nearest integer;

• the pump power consumption solpump in W, rounded to the nearest integer;

• the standby power consumption solstandby in W, to two decimal places;

• the annual auxiliary electricity consumption Q_aux in kWh in terms of final energy, rounded to the nearest integer;

(g)

any specific precautions that shall be taken when the solar device is assembled, installed or maintained.

5. PACKAGES OF SPACE HEATER, TEMPERATURE CONTROL AND SOLAR DEVICE U.K.

For packages of space heater, temperature control and solar device, the technical documentation referred to in Article 3(5)(c) shall include:

(a)

the name and address of the supplier;

(b)

a description of the package of space heater, temperature control and solar device model sufficient for its unambiguous identification;

(c)

where appropriate, the references of the harmonised standards applied;

(d)

where appropriate, the other technical standards and specifications used;

(e)

the identification and signature of the person empowered to bind the supplier;

(f)

technical parameters:

• the seasonal space heating energy efficiency in %, rounded to the nearest integer;

• the technical parameters set out in points 1, 3 and 4 of this Annex;

(g)

any specific precautions that shall be taken when the package of space heater, temperature control and solar device is assembled, installed or maintained.

6. PACKAGES OF COMBINATION HEATER, TEMPERATURE CONTROL AND SOLAR DEVICE U.K.

For packages of combination heater, temperature control and solar device, the technical documentation referred to in Article 3(6)(c) shall include:

(a)

the name and address of the supplier;

(b)

a description of the package of combination heater, temperature control and solar device model sufficient for its unambiguous identification;

(c)

where appropriate, the references of the harmonised standards applied;

(d)

where appropriate, the other technical standards and specifications used;

(e)

the identification and signature of the person empowered to bind the supplier;

(f)

technical parameters:

• the seasonal space heating energy efficiency and water heating energy efficiency in %, rounded to the nearest integer;

• the technical parameters set out in points 2, 3 and 4 of this Annex;

(g)

any specific precautions that shall be taken when the package of combination heater, temperature control and solar device is assembled, installed or maintained.