- Latest available (Revised)
- Original (As adopted by EU)
Commission Regulation (EU) No 813/2013 of 2 August 2013 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for space heaters and combination heaters (Text with EEA relevance)
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).
Commission Regulation (EU) No 813/2013 is up to date with all changes known to be in force on or before 16 July 2024. There are changes that may be brought into force at a future date. Changes that have been made appear in the content and are referenced with annotations.
Revised legislation carried on this site may not be fully up to date. Changes and effects are recorded by our editorial team in lists which can be found in the ‘Changes to Legislation’ area. Where those effects have yet to be applied to the text of the legislation by the editorial team they are also listed alongside the legislation in the affected provisions. Use the ‘more’ link to open the changes and effects relevant to the provision you are viewing.
For the purposes of Annexes II to V the following definitions shall apply:
for fuel boiler space heaters and fuel boiler combination heaters, a weighted average of the useful efficiency at rated heat output and the useful efficiency at 30 % of the rated heat output, expressed in %;
for electric boiler space heaters and electric boiler combination heaters, the useful efficiency at rated heat output, expressed in %;
for cogeneration space heaters not equipped with supplementary heaters, the useful efficiency at rated heat output, expressed in %;
for cogeneration space heaters equipped with supplementary heaters, a weighted average of the useful efficiency at rated heat output with supplementary heater disabled, and the useful efficiency at rated heat output with supplementary heater enabled, expressed in %;
(a)an indication of off mode condition; or
(b)functionalities intended only to ensure electromagnetic compatibility pursuant to the Electromagnetic Compatibility Regulations 2016;]
Textual Amendments
From 26 September 2015 the seasonal space heating energy efficiency and useful efficiencies of heaters shall not fall below the following values:
Fuel boiler space heaters with rated heat output ≤ 70 kW and fuel boiler combination heaters with rated heat output ≤ 70 kW, with the exception of type B1 boilers with rated heat output ≤ 10 kW and type B1 combination boilers with rated heat output ≤ 30 kW:
The seasonal space heating energy efficiency shall not fall below 86 %.
Type B1 boilers with rated heat output ≤ 10 kW and type B1 combination boilers with rated heat output ≤ 30 kW:
The seasonal space heating energy efficiency shall not fall below 75 %.
Fuel boiler space heaters with rated heat output > 70 kW and ≤ 400 kW and fuel boiler combination heaters with rated heat output > 70 kW and ≤ 400 kW:
The useful efficiency at 100 % of the rated heat output shall not fall below 86 %, and the useful efficiency at 30 % of the rated heat output shall not fall below 94 %.
Electric boiler space heaters and electric boiler combination heaters:
The seasonal space heating energy efficiency shall not fall below 30 %.
Cogeneration space heaters:
The seasonal space heating energy efficiency shall not fall below 86 %.
Heat pump space heaters and heat pump combination heaters, with the exception of low-temperature heat pumps:
The seasonal space heating energy efficiency shall not fall below 100 %.
Low-temperature heat pumps:
The seasonal space heating energy efficiency shall not fall below 115 %.
From 26 September 2017 the seasonal space heating energy efficiency of electric boiler space heaters, electric boiler combination heaters, cogeneration space heaters, heat pump space heaters and heat pump combination heaters shall not fall below the following values:
Electric boiler space heaters and electric boiler combination heaters:
The seasonal space heating energy efficiency shall not fall below 36 %.
Cogeneration space heaters:
The seasonal space heating energy efficiency shall not fall below 100 %.
Heat pump space heaters and heat pump combination heaters, with the exception of low-temperature heat pumps:
The seasonal space heating energy efficiency shall not fall below 110 %.
Low-temperature heat pumps:
The seasonal space heating energy efficiency shall not fall below 125 %.
Declared load profile | 3XS | XXS | XS | S | M | L | XL | XXL | 3XL | 4XL |
---|---|---|---|---|---|---|---|---|---|---|
Water heating energy efficiency | 22 % | 23 % | 26 % | 26 % | 30 % | 30 % | 30 % | 32 % | 32 % | 32 % |
Declared load profile | 3XS | XXS | XS | S | M | L | XL | XXL | 3XL | 4XL |
---|---|---|---|---|---|---|---|---|---|---|
Water heating energy efficiency | 32 % | 32 % | 32 % | 32 % | 36 % | 37 % | 38 % | 60 % | 64 % | 64 % |
From 26 September 2015 the sound power level of heat pump space heaters and heat pump combination heaters shall not exceed the following values:
Rated heat output ≤ 6 kW | Rated heat output > 6 kW and ≤ 12 kW | Rated heat output > 12 kW and ≤ 30 kW | Rated heat output > 30 kW and ≤ 70 kW | ||||
---|---|---|---|---|---|---|---|
Sound power level (LWA ), indoors | Sound power level (LWA ), outdoors | Sound power level (LWA ), indoors | Sound power level (LWA ), outdoors | Sound power level (LWA ), indoors | Sound power level (LWA ), outdoors | Sound power level (LWA ), indoors | Sound power level (LWA ), outdoors |
60 dB | 65 dB | 65 dB | 70 dB | 70 dB | 78 dB | 80 dB | 88 dB |
fuel boiler space heaters and fuel boiler combination heaters using gaseous fuels: 56 mg/kWh fuel input in terms of GCV;
fuel boiler space heaters and fuel boiler combination heaters using liquid fuels: 120 mg/kWh fuel input in terms of GCV;
cogeneration space heaters equipped with external combustion using gaseous fuels: 70 mg/kWh fuel input in terms of GCV;
cogeneration space heaters equipped with external combustion using liquid fuels: 120 mg/kWh fuel input in terms of GCV;
cogeneration space heaters equipped with an internal combustion engine using gaseous fuels: 240 mg/kWh fuel input in terms of GCV;
cogeneration space heaters equipped with an internal combustion engine using liquid fuels: 420 mg/kWh fuel input in terms of GCV;
heat pump space heaters and heat pump combination heaters equipped with external combustion using gaseous fuels: 70 mg/kWh fuel input in terms of GCV;
heat pump space heaters and heat pump combination heaters equipped with external combustion using liquid fuels: 120 mg/kWh fuel input in terms of GCV;
heat pump space heaters and heat pump combination heaters equipped with an internal combustion engine using gaseous fuels: 240 mg/kWh fuel input in terms of GCV;
heat pump space heaters and heat pump combination heaters equipped with an internal combustion engine using liquid fuels: 420 mg/kWh fuel input in terms of GCV.
From 26 September 2015 the following product information on heaters shall be provided:
the instruction manuals for installers and end-users, and free access websites of manufacturers, their authorised representatives and importers shall contain the following elements:
for boiler space heaters, boiler combination heaters and cogeneration space heaters, the technical parameters set out in Table 1, measured and calculated in accordance with Annex III;
for heat pump space heaters and heat pump combination heaters, the technical parameters set out in Table 2, measured and calculated in accordance with Annex III;
any specific precautions that shall be taken when the heater is assembled, installed or maintained;
for type B1 boilers and type B1 combination boilers, their characteristics and the following standard text: ‘This natural draught boiler is intended to be connected only to a flue shared between multiple dwellings in existing buildings that evacuates the residues of combustion to the outside of the room containing the boiler. It draws the combustion air directly from the room and incorporates a draught diverter. Due to lower efficiency, any other use of this boiler shall be avoided and would result in higher energy consumption and higher operating costs.’;
for heat generators designed for heaters, and heater housings to be equipped with such heat generators, their characteristics, the requirements for assembly, to ensure compliance with the ecodesign requirements for heaters and, where appropriate, the list of combinations recommended by the manufacturer;
information relevant for disassembly, recycling and/or disposal at end-of-life;
the technical documentation for the purposes of conformity assessment pursuant to Article 4 shall contain the following elements:
the elements specified in point (a);
for heat pump space heaters and heat pump combination heaters where the information relating to a specific model comprising a combination of indoor and outdoor units has been obtained by calculation on the basis of design and/or extrapolation from other combinations, the details of such calculations and/or extrapolations, and of any tests undertaken to verify the accuracy of the calculations, including details of the mathematical model for calculating the performance of such combinations and details of the measurements taken to verify this model;
the following information shall be durably marked on the heater:
if applicable, ‘type B1 boiler’ or ‘type B1 combination boiler’;
for cogeneration space heaters, the electrical capacity.
Information requirements for boiler space heaters, boiler combination heaters and cogeneration space heaters
a High-temperature regime means 60 °C return temperature at heater inlet and 80 °C feed temperature at heater outlet. | ||||||||
b Low temperature means for condensing boilers 30 °C, for low-temperature boilers 37 °C and for other heaters 50 °C return temperature (at heater inlet). | ||||||||
Model(s): [information identifying the model(s) to which the information relates] | ||||||||
Condensing boiler: [yes/no] | ||||||||
Low-temperatureb boiler: [yes/no] | ||||||||
B1 boiler: [yes/no] | ||||||||
Cogeneration space heater: [yes/no] | If yes, equipped with a supplementary heater: [yes/no] | |||||||
Combination heater: [yes/no] | ||||||||
Item | Symbol | Value | Unit | Item | Symbol | Value | Unit | |
---|---|---|---|---|---|---|---|---|
Rated heat output | Prated | x | kW | Seasonal space heating energy efficiency | ηs | x | % | |
For boiler space heaters and boiler combination heaters: Useful heat output | For boiler space heaters and boiler combination heaters: Useful efficiency | |||||||
At rated heat output and high-temperature regimea | P4 | x,x | kW | At rated heat output and high-temperature regimea | η4 | x,x | % | |
At 30 % of rated heat output and low-temperature regimeb | P1 | x,x | kW | At 30 % of rated heat output and low-temperature regimeb | η1 | x,x | % | |
For cogeneration space heaters: Useful heat output | For cogeneration space heaters: Useful efficiency | |||||||
At rated heat output of cogeneration space heater with supplementary heater disabled | PCHP100 + Sup0 | x,x | kW | At rated heat output of cogeneration space heater with supplementary heater disabled | ηCHP100 + Sup0 | x,x | % | |
At rated heat output of cogeneration space heater with supplementary heater enabled | PCHP100 + Sup100 | x,x | kW | At rated heat output of cogeneration space heater with supplementary heater enabled | ηCHP100 + Sup100 | x,x | % | |
For cogeneration space heaters: Electrical efficiency | Supplementary heater | |||||||
At rated heat output of cogeneration space heater with supplementary heater disabled | ηel,CHP100 + Sup0 | x,x | % | Rated heat output | Psup | x,x | kW | |
At rated heat output of cogeneration space heater with supplementary heater enabled | ηel,CHP100 + Sup100 | x,x | % | Type of energy input | ||||
Auxiliary electricity consumption | Other items | |||||||
At full load | elmax | x,xxx | kW | Standby heat loss | Pstby | x,xxx | kW | |
At part load | elmin | x,xxx | kW | Ignition burner power consumption | Pign | x,xxx | kW | |
In standby mode | PSB | x,xxx | kW | Emissions of nitrogen oxides | NOx | x | mg/kWh | |
For combination heaters: | ||||||||
Declared load profile | Water heating energy efficiency | ηwh | x | % | ||||
Daily electricity consumption | Qelec | x,xxx | kWh | Daily fuel consumption | Qfuel | x,xxx | kWh | |
Contact details | Name and address of the manufacturer or its authorised representative. |
Information requirements for heat pump space heaters and heat pump combination heaters
a For heat pump space heaters and heat pump combination heaters, the rated heat output Prated is equal to the design load for heating Pdesignh, and the rated heat output of a supplementary heater Psup is equal to the supplementary capacity for heating sup(Tj). | ||||||||
b If Cdh is not determined by measurement then the default degradation coefficient is Cdh = 0,9. | ||||||||
Model(s): [information identifying the model(s) to which the information relates] | ||||||||
Air-to-water heat pump: [yes/no] | ||||||||
Water-to-water heat pump: [yes/no] | ||||||||
Brine-to-water heat pump: [yes/no] | ||||||||
Low-temperature heat pump: [yes/no] | ||||||||
Equipped with a supplementary heater: [yes/no] | ||||||||
Heat pump combination heater: [yes/no] | ||||||||
Parameters shall be declared for medium-temperature application, except for low-temperature heat pumps. For low-temperature heat pumps, parameters shall be declared for low-temperature application. | ||||||||
Parameters shall be declared for average climate conditions. | ||||||||
Item | Symbol | Value | Unit | Item | Symbol | Value | Unit | |
---|---|---|---|---|---|---|---|---|
Rated heat output a | Prated | x | kW | Seasonal space heating energy efficiency | ηs | x | % | |
Declared capacity for heating for part load at indoor temperature 20 °C and outdoor temperature Tj | Declared coefficient of performance or primary energy ratio for part load at indoor temperature 20 °C and outdoor temperature Tj | |||||||
Tj = – 7 °C | Pdh | x,x | kW | Tj = – 7 °C | COPd or PERd | x,xx or x,x | – or % | |
Tj = + 2 °C | Pdh | x,x | kW | Tj = + 2 °C | COPd or PERd | x,xx or x,x | – or % | |
Tj = + 7 °C | Pdh | x,x | kW | Tj = + 7 °C | COPd or PERd | x,xx or x,x | – or % | |
Tj = + 12 °C | Pdh | x,x | kW | Tj = + 12 °C | COPd or PERd | x,xx or x,x | – or % | |
Tj = bivalent temperature | Pdh | x,x | kW | Tj = bivalent temperature | COPd or PERd | x,xx or x,x | – or % | |
Tj = operation limit temperature | Pdh | x,x | kW | Tj = operation limit temperature | COPd or PERd | x,xx or x,x | – or % | |
For air-to-water heat pumps: Tj = – 15 °C (if TOL < – 20 °C) | Pdh | x,x | kW | For air-to-water heat pumps: Tj = – 15 °C (if TOL < – 20 °C) | COPd or PERd | x,xx or x,x | – or % | |
Bivalent temperature | Tbiv | x | °C | For air-to-water heat pumps: Operation limit temperature | TOL | x | °C | |
Cycling interval capacity for heating | Pcych | x,x | kW | Cycling interval efficiency | COPcyc or PERcyc | x,xx or x,x | – or % | |
Degradation co-efficientb | Cdh | x,x | — | Heating water operating limit temperature | WTOL | x | °C | |
Power consumption in modes other than active mode | Supplementary heater | |||||||
Off mode | POFF | x,xxx | kW | Rated heat outputa | Psup | x,x | kW | |
Thermostat-off mode | PTO | x,xxx | kW | |||||
Standby mode | PSB | x,xxx | kW | Type of energy input | ||||
Crankcase heater mode | PCK | x,xxx | kW | |||||
Other items | ||||||||
Capacity control | fixed/variable | For air-to-water heat pumps: Rated air flow rate, outdoors | — | x | m3/h | |||
Sound power level, indoors/outdoors | LWA | x/x | dB | For water-/brine-to-water heat pumps: Rated brine or water flow rate, outdoor heat exchanger | — | x | m3/h | |
Emissions of nitrogen oxides | NOx | x | mg/kWh | |||||
For heat pump combination heater: | ||||||||
Declared load profile | x | Water heating energy efficiency | ηwh | x | % | |||
Daily electricity consumption | Qelec | x,xxx | kWh | Daily fuel consumption | Qfuel | x,xxx | kWh | |
Contact details | Name and address of the manufacturer or its authorised representative. |
For the purposes of compliance and verification of compliance with the requirements of this Regulation, measurements and calculations shall be made using [F2designated standards], or using other reliable, accurate and reproducible methods that take into account the generally recognised state-of-the-art methods. They shall meet the conditions and technical parameters set out in points 2 to 5.
General conditions for measurements and calculations
For the purposes of the measurements set out in points 2 to 5, the indoor ambient temperature shall be set at 20 °C ± 1 °C.
For the purposes of the calculations set out in points 3 to 5, consumption of electricity shall be multiplied by a conversion coefficient CC of 2,5.
Emissions of nitrogen oxides shall be measured as the sum of nitrogen monoxide and nitrogen dioxide, and expressed in nitrogen dioxide.
For heaters equipped with supplementary heaters, the measurement and calculation of rated heat output, seasonal space heating energy efficiency, water heating energy efficiency, sound power level and emissions of nitrogen oxides shall take account of the supplementary heater.
Declared values for rated heat output, seasonal space heating energy efficiency, water heating energy efficiency, sound power level and emissions of nitrogen oxides shall be rounded to the nearest integer.
Any heat generator designed for a heater, and any heater housing to be equipped with such a heat generator, shall be tested with an appropriate heater housing and heat generator, respectively.
Seasonal space heating energy efficiency of boiler space heaters, boiler combination heaters and cogeneration space heaters
The seasonal space heating energy efficiency ηs shall be calculated as the seasonal space heating energy efficiency in active mode ηson , corrected by contributions accounting for temperature controls, auxiliary electricity consumption, standby heat loss, ignition burner power consumption (if applicable) and, for cogeneration space heaters, corrected by adding the electrical efficiency multiplied by a conversion coefficient CC of 2,5.
Seasonal space heating energy efficiency of heat pump space heaters and heat pump combination heaters
For establishing the rated coefficient of performance COPrated or rated primary energy ratio PERrated , the sound power level or emissions of nitrogen oxides, the operating conditions shall be the standard rating conditions set out in Table 3 and the same declared capacity for heating shall be used.
The active mode coefficient of performance SCOPon or active mode primary energy ratio SPERon shall be calculated on the basis of the part load for heating Ph(Tj), the supplementary capacity for heating sup(Tj) (if applicable) and the bin-specific coefficient of performance COPbin(Tj) or bin-specific primary energy ratio PERbin(Tj), weighted by the bin-hours for which the bin conditions apply, using the following conditions:
the reference design conditions set out in Table 4;
the European reference heating season under average climate conditions set out in Table 5;
if applicable, the effects of any degradation of energy efficiency caused by cycling depending on the type of control of the heating capacity.
The reference annual heat demand QH shall be the design load for heating Pdesignh multiplied by the annual equivalent active mode hours HHE of 2 066.
The annual energy consumption QHE shall be calculated as the sum of:
the ratio of the reference annual heating demand QH and the active mode coefficient of performance SCOPon or active mode primary energy ratio SPERon and
the energy consumption for off, thermostat-off, standby, and crankcase heater mode during the heating season.
The seasonal coefficient of performance SCOP or seasonal primary energy ratio SPER shall be calculated as the ratio of the reference annual heat demand QH and the annual energy consumption QHE .
The seasonal space heating energy efficiency ηs shall be calculated as the seasonal coefficient of performance SCOP divided by the conversion coefficient CC or the seasonal primary energy ratio SPER, corrected by contributions accounting for temperature controls and, for water-/brine-to-water heat pump space heaters and heat pump combination heaters, the electricity consumption of one or more ground water pumps.
Water heating energy efficiency of combination heaters
The water heating energy efficiency ηwh of a combination heater shall be calculated as the ratio between the reference energy Qref of the declared load profile and the energy required for its generation under the following conditions:
measurements shall be carried out using the load profiles set out in Table 7;
measurements shall be carried out using a 24-hour measurement cycle as follows:
00:00 to 06:59: no water draw-off;
from 07:00: water draw-offs according to the declared load profile;
from end of last water draw-off until 24:00: no water draw-off;
the declared load profile shall be the maximum load profile or the load profile one below the maximum load profile;
for heat pump combination heaters, the following additional conditions apply:
heat pump combination heaters shall be tested under the conditions set out in Table 3;
heat pump combination heaters which use ventilation exhaust air as the heat source shall be tested under the conditions set out in Table 6.
Textual Amendments
Standard rating conditions for heat pump space heaters and heat pump combination heaters
Heat source | Outdoor heat exchanger | Indoor heat exchanger | |||
---|---|---|---|---|---|
Inlet dry bulb (wet bulb) temperature | Heat pump space heaters and heat pump combination heaters, except low-temperature heat pumps | Low-temperature heat pumps | |||
Inlet temperature | Outlet temperature | Inlet temperature | Outlet temperature | ||
Outdoor air | + 7 °C (+ 6 °C) | + 47 °C | + 55 °C | + 30 °C | + 35 °C |
Exhaust air | + 20 °C (+ 12 °C) | ||||
Inlet/outlet temperature | |||||
Water | + 10 °C/+ 7 °C | ||||
Brine | 0 °C/– 3 °C |
Reference design conditions for heat pump space heaters and heat pump combination heaters, temperatures in dry bulb air temperature (wet bulb air temperature indicated in brackets)
Reference design temperature | Bivalent temperature | Operation limit temperature |
---|---|---|
Tdesignh | Tbiv | TOL |
– 10 (– 11) °C | maximum + 2 °C | maximum – 7 °C |
European reference heating season under average climate conditions for heat pump space heaters and heat pump combination heaters
binj | Tj [°C] | Hj [h/annum] |
---|---|---|
1 to 20 | – 30 to – 11 | 0 |
21 | -10 | 1 |
22 | -9 | 25 |
23 | -8 | 23 |
24 | -7 | 24 |
25 | -6 | 27 |
26 | -5 | 68 |
27 | -4 | 91 |
28 | -3 | 89 |
29 | -2 | 165 |
30 | -1 | 173 |
31 | 0 | 240 |
32 | 1 | 280 |
33 | 2 | 320 |
34 | 3 | 357 |
35 | 4 | 356 |
36 | 5 | 303 |
37 | 6 | 330 |
38 | 7 | 326 |
39 | 8 | 348 |
40 | 9 | 335 |
41 | 10 | 315 |
42 | 11 | 215 |
43 | 12 | 169 |
44 | 13 | 151 |
45 | 14 | 105 |
46 | 15 | 74 |
Total hours: | 4 910 |
Maximum ventilation exhaust air available [m3/h], at humidity of 5,5 g/m3
Declared load profile | XXS | XS | S | M | L | XL | XXL | 3XL | 4XL |
---|---|---|---|---|---|---|---|---|---|
Maximum ventilation exhaust air available | 109 | 128 | 128 | 159 | 190 | 870 | 1 021 | 2 943 | 8 830 |
Water heating load profiles of combination heaters
h | 3XS | XXS | XS | S | |||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Q tap | f | Tm | Q tap | f | Tm | Q tap | f | Tm | Q tap | f | Tm | Tp | |
kWh | l/min | °C | kWh | l/min | °C | kWh | l/min | °C | kWh | l/min | °C | °C | |
07:00 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | 0,105 | 3 | 25 | ||||
07:05 | 0,015 | 2 | 25 | ||||||||||
07:15 | 0,015 | 2 | 25 | ||||||||||
07:26 | 0,015 | 2 | 25 | ||||||||||
07:30 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | 0,525 | 3 | 35 | 0,105 | 3 | 25 | |
07:45 | |||||||||||||
08:01 | |||||||||||||
08:05 | |||||||||||||
08:15 | |||||||||||||
08:25 | |||||||||||||
08:30 | 0,105 | 2 | 25 | 0,105 | 3 | 25 | |||||||
08:45 | |||||||||||||
09:00 | 0,105 | 2 | 25 | ||||||||||
09:30 | 0,105 | 2 | 25 | 0,105 | 2 | 25 | 0,105 | 3 | 25 | ||||
10:00 | |||||||||||||
10:30 | |||||||||||||
11:00 | |||||||||||||
11:30 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | 0,105 | 3 | 25 | ||||
11:45 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | 0,105 | 3 | 25 | ||||
12:00 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | |||||||
12:30 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | |||||||
12:45 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | 0,525 | 3 | 35 | 0,315 | 4 | 10 | 55 |
14:30 | 0,015 | 2 | 25 | ||||||||||
15:00 | 0,015 | 2 | 25 | ||||||||||
15:30 | 0,015 | 2 | 25 | ||||||||||
16:00 | 0,015 | 2 | 25 | ||||||||||
16:30 | |||||||||||||
17:00 | |||||||||||||
18:00 | 0,105 | 2 | 25 | 0,105 | 3 | 25 | |||||||
18:15 | 0,105 | 2 | 25 | 0,105 | 3 | 40 | |||||||
18:30 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | |||||||
19:00 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | |||||||
19:30 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | |||||||
20:00 | 0,105 | 2 | 25 | ||||||||||
20:30 | 1,05 | 3 | 35 | 0,42 | 4 | 10 | 55 | ||||||
20:45 | 0,105 | 2 | 25 | ||||||||||
20:46 | |||||||||||||
21:00 | 0,105 | 2 | 25 | ||||||||||
21:15 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | |||||||
21:30 | 0,015 | 2 | 25 | 0,525 | 5 | 45 | |||||||
21:35 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | |||||||
21:45 | 0,015 | 2 | 25 | 0,105 | 2 | 25 | |||||||
Qref | 0,345 | 2,1 | 2,1 | 2,1 |
h | M | L | XL | |||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Q tap | f | Tm | Tp | Q tap | f | Tm | Tp | Q tap | f | Tm | Tp | |
kWh | l/min | °C | °C | kWh | l/min | °C | °C | kWh | l/min | °C | °C | |
07:00 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
07:05 | 1,4 | 6 | 40 | 1,4 | 6 | 40 | ||||||
07:15 | 1,82 | 6 | 40 | |||||||||
07:26 | 0,105 | 3 | 25 | |||||||||
07:30 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | ||||||
07:45 | 0,105 | 3 | 25 | 4,42 | 10 | 10 | 40 | |||||
08:01 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | ||||||
08:05 | 3,605 | 10 | 10 | 40 | ||||||||
08:15 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | ||||||
08:25 | 0,105 | 3 | 25 | |||||||||
08:30 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
08:45 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
09:00 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
09:30 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
10:00 | 0,105 | 3 | 25 | |||||||||
10:30 | 0,105 | 3 | 10 | 40 | 0,105 | 3 | 10 | 40 | 0,105 | 3 | 10 | 40 |
11:00 | 0,105 | 3 | 25 | |||||||||
11:30 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
11:45 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
12:00 | ||||||||||||
12:30 | ||||||||||||
12:45 | 0,315 | 4 | 10 | 55 | 0,315 | 4 | 10 | 55 | 0,735 | 4 | 10 | 55 |
14:30 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
15:00 | 0,105 | 3 | 25 | |||||||||
15:30 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
16:00 | 0,105 | 3 | 25 | |||||||||
16:30 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
17:00 | 0,105 | 3 | 25 | |||||||||
18:00 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
18:15 | 0,105 | 3 | 40 | 0,105 | 3 | 40 | 0,105 | 3 | 40 | |||
18:30 | 0,105 | 3 | 40 | 0,105 | 3 | 40 | 0,105 | 3 | 40 | |||
19:00 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | |||
19:30 | ||||||||||||
20:00 | ||||||||||||
20:30 | 0,735 | 4 | 10 | 55 | 0,735 | 4 | 10 | 55 | 0,735 | 4 | 10 | 55 |
20:45 | ||||||||||||
20:46 | 4,42 | 10 | 10 | 40 | ||||||||
21:00 | 3,605 | 10 | 10 | 40 | ||||||||
21:15 | 0,105 | 3 | 25 | 0,105 | 3 | 25 | ||||||
21:30 | 1,4 | 6 | 40 | 0,105 | 3 | 25 | 4,42 | 10 | 10 | 40 | ||
21:35 | ||||||||||||
21:45 | ||||||||||||
Qref | 5,845 | 11,655 | 19,07 |
h | XXL | 3XL | 4XL | |||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Q tap | f | Tm | Tp | Q tap | f | Tm | Tp | Q tap | f | Tm | Tp | |
kWh | l/min | °C | °C | kWh | l/min | °C | °C | kWh | l/min | °C | °C | |
07:00 | 0,105 | 3 | 25 | 11,2 | 48 | 40 | 22,4 | 96 | 40 | |||
07:05 | ||||||||||||
07:15 | 1,82 | 6 | 40 | |||||||||
07:26 | 0,105 | 3 | 25 | |||||||||
07:30 | ||||||||||||
07:45 | 6,24 | 16 | 10 | 40 | ||||||||
08:01 | 0,105 | 3 | 25 | 5,04 | 24 | 25 | 10,08 | 48 | 25 | |||
08:05 | ||||||||||||
08:15 | 0,105 | 3 | 25 | |||||||||
08:25 | ||||||||||||
08:30 | 0,105 | 3 | 25 | |||||||||
08:45 | 0,105 | 3 | 25 | |||||||||
09:00 | 0,105 | 3 | 25 | 1,68 | 24 | 25 | 3,36 | 48 | 25 | |||
09:30 | 0,105 | 3 | 25 | |||||||||
10:00 | 0,105 | 3 | 25 | |||||||||
10:30 | 0,105 | 3 | 10 | 40 | 0,84 | 24 | 10 | 40 | 1,68 | 48 | 10 | 40 |
11:00 | 0,105 | 3 | 25 | |||||||||
11:30 | 0,105 | 3 | 25 | |||||||||
11:45 | 0,105 | 3 | 25 | 1,68 | 24 | 25 | 3,36 | 48 | 25 | |||
12:00 | ||||||||||||
12:30 | ||||||||||||
12:45 | 0,735 | 4 | 10 | 55 | 2,52 | 32 | 10 | 55 | 5,04 | 64 | 10 | 55 |
14:30 | 0,105 | 3 | 25 | |||||||||
15:00 | 0,105 | 3 | 25 | |||||||||
15:30 | 0,105 | 3 | 25 | 2,52 | 24 | 25 | 5,04 | 48 | 25 | |||
16:00 | 0,105 | 3 | 25 | |||||||||
16:30 | 0,105 | 3 | 25 | |||||||||
17:00 | 0,105 | 3 | 25 | |||||||||
18:00 | 0,105 | 3 | 25 | |||||||||
18:15 | 0,105 | 3 | 40 | |||||||||
18:30 | 0,105 | 3 | 40 | 3,36 | 24 | 25 | 6,72 | 48 | 25 | |||
19:00 | 0,105 | 3 | 25 | |||||||||
19:30 | ||||||||||||
20:00 | ||||||||||||
20:30 | 0,735 | 4 | 10 | 55 | 5,88 | 32 | 10 | 55 | 11,76 | 64 | 10 | 55 |
20:45 | ||||||||||||
20:46 | 6,24 | 16 | 10 | 40 | ||||||||
21:00 | ||||||||||||
21:15 | 0,105 | 3 | 25 | |||||||||
21:30 | 6,24 | 16 | 10 | 40 | 12,04 | 48 | 40 | 24,08 | 96 | 40 | ||
21:35 | ||||||||||||
21:45 | ||||||||||||
Qref | 24,53 | 46,76 | 93,52 |
Textual Amendments
F3Substituted by Commission Regulation (EU) 2016/2282 of 30 November 2016 amending Regulations (EC) No 1275/2008, (EC) No 107/2009, (EC) No 278/2009, (EC) No 640/2009, (EC) No 641/2009, (EC) No 642/2009, (EC) No 643/2009, (EU) No 1015/2010, (EU) No 1016/2010, (EU) No 327/2011, (EU) No 206/2012, (EU) No 547/2012, (EU) No 932/2012, (EU) No 617/2013, (EU) No 666/2013, (EU) No 813/2013, (EU) No 814/2013, (EU) No 66/2014, (EU) No 548/2014, (EU) No 1253/2014, (EU) 2015/1095, (EU) 2015/1185, (EU) 2015/1188, (EU) 2015/1189 and (EU) 2016/2281 with regard to the use of tolerances in verification procedures (Text with EEA relevance).
The verification tolerances defined in this Annex relate only to the verification of the measured parameters by [F4Great Britain] authorities and shall not be used by the manufacturer or importer as an allowed tolerance to establish the values in the technical documentation or in interpreting these values with a view to achieving compliance or to communicate better performance by any means.
Textual Amendments
F4Words in Annex 4 substituted (31.12.2020) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 (S.I. 2019/539), reg. 1(3), Sch. 2 para. 19(10)(a) (as amended by S.I. 2020/1528, regs. 1(2), 6(1)(2)(b)(xviii)); 2020 c. 1, Sch. 5 para. 1(1)
[F5When verifying the compliance of a product model with the requirements laid down in this Regulation, for the requirements referred to in this Annex the authorities of Great Britain must apply the following procedure—]
Textual Amendments
F5Words in Annex 4 substituted (31.12.2020) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 (S.I. 2019/539), reg. 1(3), Sch. 2 para. 19(10)(b) (as amended by S.I. 2020/1528, regs. 1(2), 6(3)(4)(b)(xviii)); 2020 c. 1, Sch. 5 para. 1(1)
The [F4Great Britain] authorities shall verify one single unit of the model.
The model shall be considered to comply with the applicable requirements if:
the values given in the technical documentation pursuant to [F6paragraph 1(2) of Part 1 of Schedule 1A to the Ecodesign for Energy-Related Products Regulations 2010], and, where applicable, the values used to calculate these values, are not more favourable for the manufacturer or importer than the results of the corresponding measurements carried out pursuant to [F7paragraph 1(2)(b)(vii) of Part 1 of Schedule 1A to those Regulations]; and
the declared values meet any requirements laid down in this Regulation, and any required product information published by the manufacturer or importer does not contain values that are more favourable for the manufacturer or importer than the declared values; and
when the [F4Great Britain] authorities test the unit of the model, the determined values (the values of the relevant parameters as measured in testing and the values calculated from these measurements) comply with the respective verification tolerances as given in Table 8.
If the results referred to in point 2(a) or (b) are not achieved, the model and all other equivalent models shall be considered not to comply with this Regulation.
If the result referred to in point 2(c) is not achieved, the [F4Great Britain] authorities shall select three additional units of the same model for testing. As an alternative, the three additional units selected may be of one or more different equivalent models.
The model shall be considered to comply with the applicable requirements if, for these three units, the arithmetical mean of the determined values complies with the respective verification tolerances given in Table 8.
If the result referred to in point 5 is not achieved, the model and all other equivalent models shall be considered not to comply with this Regulation.
F8...
Textual Amendments
F6Words in Annex 4 para. (2)(a) substituted (31.12.2020) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 (S.I. 2019/539), reg. 1(3), Sch. 2 para. 19(10)(c)(i); 2020 c. 1, Sch. 5 para. 1(1)
The [F4Great Britain] authorities shall use the measurement and calculation methods set out in Annex III.
The [F4Great Britain] authorities shall only apply the verification tolerances that are set out in Table 8 and shall only use the procedure described in points 1 to [F96] for the requirements referred to in this Annex. No other tolerances, such as those set out in [F10designated] standards or in any other measurement method, shall be applied.
Textual Amendments
Verification tolerances
Parameters | Verification tolerances |
---|---|
Seasonal space-heating energy efficiency, η s | The determined value shall not be lower than the declared value by more than 8 %. |
Water-heating energy efficiency, η wh | The determined value shall not be lower than the declared value by more than 8 %. |
Sound power level, L WA | The determined value shall not exceed the declared value by more than 2 dB(A). |
Emissions of nitrogen oxides | The determined value shall not exceed the declared value by more than 20 %.] |
At the time of entry into force of this Regulation, the best available technology on the market for heaters in terms of seasonal space heating energy efficiency, water heating energy efficiency, sound power level and emissions of nitrogen oxides was identified as follows:
Benchmark for seasonal space heating energy efficiency in medium-temperature application: 145 %;
Benchmarks for water heating energy efficiency of combination heaters:
Declared load profile | 3XS | XXS | XS | S | M | L | XL | XXL | 3XL | 4XL |
---|---|---|---|---|---|---|---|---|---|---|
Water heating energy efficiency | 35 % | 35 % | 38 % | 38 % | 75 % | 110 % | 115 % | 120 % | 130 % | 130 % |
Benchmarks for sound power level (LWA ), outdoor, of heat pump space heaters and of heat pump combination heaters with rated heat output:
≤ 6 kW: 39 dB;
> 6 kW and ≤ 12 kW: 40 dB;
> 12 kW and ≤ 30 kW: 41 dB;
> 30 kW and ≤ 70 kW: 67 dB.
Benchmarks for emissions of nitrogen oxides, expressed in nitrogen dioxide:
of boiler space heaters and boiler combination heaters using gaseous fuels: 14 mg/kWh fuel input in terms of GCV;
of boiler space heaters and boiler combination heaters using liquid fuels: 50 mg/kWh fuel input in terms of GCV.
The benchmarks specified in points 1 to 4 do not necessarily imply that a combination of these values is achievable for a single heater.
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Geographical Extent: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Show Timeline of Changes: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
This timeline shows the different versions taken from EUR-Lex before exit day and during the implementation period as well as any subsequent versions created after the implementation period as a result of changes made by UK legislation.
The dates for the EU versions are taken from the document dates on EUR-Lex and may not always coincide with when the changes came into force for the document.
For any versions created after the implementation period as a result of changes made by UK legislation the date will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. For further information see our guide to revised legislation on Understanding Legislation.
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: