Search Legislation

Advanced Search

Commission Regulation (EU) 2017/1347Show full title

Commission Regulation (EU) 2017/1347 of 13 July 2017 correcting Directive 2007/46/EC of the European Parliament and of the Council, Commission Regulation (EU) No 582/2011 and Commission Regulation (EU) 2017/1151 supplementing Regulation (EC) No 715/2007 of the European Parliament and of the Council on type-approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and on access to vehicle repair and maintenance information, amending Directive 2007/46/EC of the European Parliament and of the Council, Commission Regulation (EC) No 692/2008 and Commission Regulation (EU) No 1230/2012 and repealing Regulation (EC) No 692/2008 (Text with EEA relevance)

Help about what version

What Version

Help about UK-EU Regulation

Legislation originating from the EU

When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.

Close

This item of legislation originated from the EU

Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).

Status:

This is the original version as it was originally adopted in the EU.
This legislation may since have been updated - see the latest available (revised) version

ANNEX I

Directive 2007/46/EC is corrected as follows:

(1)

Annex I is corrected as follows:

(a)

point 3.2.12.2.1.3 is replaced by the following:

‘3.2.12.2.1.3.Type of catalytic action: … (oxidising, three-way, lean NOx trap, SCR, lean NOx catalyst or other)’;

(b)

the number of point ‘3.2.12.7.6.3.’ shall be changed in ‘3.2.12.2.7.6.3.’;

(c)

the following points are inserted:

  • ‘3.5.7.2.1.1.0.Vehicle High (NEDC): …g/km’

  • ‘3.5.7.2.1.2.0.Vehicle low (if applicable) (NEDC): …g/km’

  • ‘3.5.7.2.2.1.0.Vehicle high (NEDC): …g/km’

  • ‘3.5.7.2.2.2.0.Vehicle low (if applicable) (NEDC): …g/km’

  • ‘3.5.7.2.2.3.0.Vehicle M (if applicable) (NEDC): …g/km’

  • ‘3.5.7.2.3.1.0.Vehicle high (NEDC): …g/km’

  • ‘3.5.7.2.3.2.0.Vehicle low (if applicable) (NEDC): …g/km’

  • ‘3.5.7.2.3.3.0.Vehicle M (if applicable) (NEDC): …g/km’.

(2)

Annex VIII is corrected as follows:

(a)

in the table ‘Ambient Temperature Correction Test (ATCT)’ in point 2.1.1 the column ‘Road load matrix family’ is deleted;

(b)

the third table in point 3.1 with the columns ‘Road Load Matrix family identifier’ and ‘Variant/versions’ is deleted;

(c)

the column ‘Road Load Matrix family identifier’ in the fourth table ‘Results’ in point 3.1 is deleted;

(d)

at the bottom of the table ‘Results’ in point 3.1 the following row is added:

‘Frontal area (m2) (for road load matrix family vehicles only)’
(e)

the footnote 23 in point 3.1 is deleted;

(f)

the last line in point 3.1 under the table ‘Results’ is replaced by the following:

‘Repeat for each interpolation family.’;

(g)

the third table in point 3.2, with the columns ‘Road Load Matrix family identifier’ and ‘Variant/versions’ is deleted;

(h)

the column ‘Road Load Matrix family identifier’ in the fourth table ‘Results’ in point 3.2 is deleted;

(i)

the last row of the table ‘Results’ in point 3.2 is replaced by the following:

‘Frontal area (m2) (for road load matrix family vehicles only)’
(j)

the third table in point 3.3, with the columns ‘Road Load Matrix family identifier’ and ‘Variant/versions’ is deleted;

(k)

the column ‘Matrix family identifier’ in the fourth table ‘Results’ in point 3.3 is deleted;

(l)

the last row of the table ‘Results’ in point 3.3 is replaced by the following:

‘Frontal area (m2) (for road load matrix family vehicles only)’
(m)

point 3.5 is replaced by the following:

‘3.5.Output report(s) from the correlation tool in accordance with Implementing Regulation (EU) 2017/1151

Repeat for each interpolation family:

Interpolation family identifier [Footnote: “Type Approval Number + Interpolation Family Sequence number”]: …

VH report: …

VL report (if applicable): …

3.5.1.Deviation factor (if applicable)

Repeat for each interpolation family:

Interpolation family identifier [Footnote: “Type Approval Number + Interpolation Family Sequence number”]: …

3.5.2.Verification factor (if applicable)

Repeat for each interpolation family:

Interpolation family identifier [Footnote: “Type Approval Number + Interpolation Family Sequence number”]: …’.

(3)

Annex IX is corrected as follows:

(a)

in Part II, Incomplete Vehicles, Side 2, ‘Vehicle category M1’, ‘Vehicle category N1’, ‘Vehicle category M2’ and ‘Vehicle category N2’, point 49 is replaced by the following:

‘49.CO2 emissions/fuel consumption/electric energy consumption (m) (r):

1.All power trains, except pure electric vehicles (if applicable)

NEDC valuesCO2 emissionsFuel consumption
Urban conditions (1):… g/km… l/100 km or m3/100 km or kg/100 km (1)
Extra-urban conditions (1):… g/km… l/100 km or m3/100 km or kg/100 km (1)
Combined (1):… g/km… l/100 km or m3/100 km or kg/100 km (1)
Weighted (1), combined… g/km… l/100 km or m3/100 km or kg/100 km
Deviation factor (if applicable)
Verification factor (if applicable)“1” or “0”

2.Pure electric vehicles and OVC hybrid electric vehicles (if applicable)

Electric energy consumption (weighted, combined (1))… Wh/km
Electric range… km

3.Vehicle fitted with eco-innovation(s): yes/no (1)

3.1.General code of the eco-innovation(s) (p1): …
3.2.Total CO2 emissions savings due to the eco-innovation(s) (p2) (repeat for each reference fuel tested):
3.2.1.

NEDC savings: …g/km (if applicable)

3.2.2.

WLTP savings: …g/km (if applicable)

4.All power trains, except pure electric vehicle, under Regulation (EU) 2017/1151 (if applicable)

WLTP valuesCO2 emissionsFuel consumption
Low (1):… g/km… l/100 km or m3/100 km or kg/100 km (1)
Medium (1):… g/km… l/100 km or m3/100 km or kg/100 km (1)
High (1):… g/km… l/100 km or m3/100 km or kg/100 km (1)
Extra High (1):… g/km… l/100 km or m3/100 km or kg/100 km (1)
Combined:… g/km… l/100 km or m3/100 km or kg/100 km (1)
Weighted, combined (1)… g/km… l/100 km or m3/100 km or kg/100 km (1)

5.Pure electric vehicles and OVC hybrid electric vehicles, under Regulation (EU) 2017/1151 (if applicable)

5.1.Pure electric vehicles
Electric energy consumption… Wh/km
Electric range… km
Electric range city… km
5.2.OVC hybrid electric vehicles
Electric energy consumption (ECAC,weighted)… Wh/km
Electric range (EAER)… km
Electric range city (EAER city)… km’;
(b)

in Part I, Complete and Completed Vehicles, Side 2, ‘Vehicle category M3’ and ‘Vehicle category N3’, and in Part II, Incomplete Vehicles, Side 2, ‘Vehicle category M3’ and ‘Vehicle category N3’, point 47.1 is deleted.

(c)

in Part I, Complete and Completed Vehicles, Side 2, ‘Vehicle category M2’ and ‘Vehicle category N2’, and in Part II, Incomplete Vehicles, Side 2, ‘Vehicle category M2’ and ‘Vehicle category N2’, a reference to explanatory note ‘(r)’ is added to point 47.1.

ANNEX II

Regulation (EU) No 582/2011 is corrected as follows:

(1)

in Annex I, Appendix 9 is replaced by the following:

‘Appendix 9 EC Type-Approval Certification Numbering System

Section 3 of the EC type-approval number issued according to Articles 6(1), 8(1) and 10(1) shall be composed by the number of the implementing regulatory act or the latest amending regulatory act applicable to the EC type-approval. The number shall be followed by an alphabetical character reflecting the requirements of OBD and SCR systems in accordance with Table 1.

Table 1

Key:
a

“NOx OTL” monitoring requirements as set out in Table 1 of Annex X for compression ignition and dual-fuel engines and vehicles and Table 2 of Annex X for positive ignition engines and vehicles.

b

“PM OTL” monitoring requirements as set out in Table 1 of Annex X for compression ignition and dual-fuel engines and vehicles.

c

“Performance monitoring” requirements as set out in point 2.1.1 of Annex X.

d

Reagent quality “phase-in” requirements as set out in point 7.1 of Annex XIII.

e

Reagent quality “general” requirements as set out in point 7.1.1 of Annex XIII.

f

“CO OTL” monitoring requirements as set out in Table 2 of Annex X for positive ignition engines and vehicles.

g

IUPR “Phase-in” requirements as set out in Section 6 of Annex X.

h

IUPR “General” requirements as set out in Section 6 of Annex X.

i

For positive-ignition engines and vehicles equipped with such engines.

j

For compression-ignition and dual-fuel engines and vehicles equipped with such engines.

l

Only applicable to positive-ignition engines and vehicles equipped with such engines.

k

Additional provisions concerning monitoring requirements as set out in paragraph 2.3.1.2 of Annex 9A to UNECE Regulation No 49.

m

IUPR specifications are set out in Annex X. Positive Ignition engines and vehicles equipped with such engines are not subjected to IUPR.

n

ISC requirement set out in Appendix 1 to Annex II.

N/A

Not applicable.’’.

CharacterNOx OTLaPM OTLbCO OTLfIUPRmReagent qualityAdditional OBD monitorskPower threshold requirementsnImplementation dates: new typesImplementation dates: all vehiclesLast date of registration

Ai j

Bj

Row “phase-in period” of Table 1 or Table 2Performance MonitoringcN/APhase-ingPhase-indN/A20 %31.12.201231.12.2013

31.8.2015i

30.12.2016j

BlRow “phase-in period” of Tables 1 and 2N/ARow “phase-in period” of Table 2N/APhase-indN/A20 %1.9.20141.9.201530.12.2016
CRow “general requirements” of Table 1 or Table 2Row “general requirements” of Table 1Row “general requirements” of Table 2GeneralhGeneraleYes20 %31.12.201531.12.201631.8.2019
DRow “general requirements” of Table 1 or Table 2Row “general requirements” of Table 1Row “general requirements” of Table 2GeneralhGeneraleYes10 %1.9.20181.9.2019
(2)

in Annex II, in Appendix 1, point 1 is replaced by the following:

‘1.INTRODUCTION

This Appendix describes the procedure to determine gaseous emissions from on-vehicle on-road measurements using Portable Emissions Measurement Systems (hereinafter “PEMS”). The pollutant emissions to be measured from the exhaust of the engine include the following components: carbon monoxide, total hydrocarbons and nitrogen oxides for compression ignition engines and carbon monoxide, non-methane hydrocarbons, methane and nitrogen oxides for positive ignition engines. Additionally, carbon dioxide shall be measured to enable the calculation procedures described in Section 4.

For engines fuelled with natural gas, the manufacturer, technical service or approval authority may choose to measure the total hydrocarbon (THC) emissions only instead of measuring the methane and non-methane hydrocarbon emissions. In that case, the emission limit for the total hydrocarbon emissions is the same as the one specified in Annex I to Regulation (EC) No 595/2009 for methane emissions. For the purposes of the calculation of the conformity factors pursuant to points 4.2.3 and 4.3.2 of this Appendix, the applicable limit shall be the methane emission limit only.

For engines fuelled with gases other than natural gas, the manufacturer, technical service or approval authority may choose to measure the total hydrocarbon (THC) emissions instead of measuring the non-methane hydrocarbon emissions. In that case, the emission limit for the total hydrocarbon emissions is the same as the one specified in Annex I to Regulation (EC) No 595/2009 for non-methane hydrocarbon emissions. For the purposes of the calculation of the Conformity Factors pursuant to points 4.2.3 and 4.3.2 of this Appendix, the applicable limit shall be the non-methane emission limit.’.

(3)

In Annex X, point 2.4.1.3 is replaced by the following:

‘2.4.1.3.The OBD standard Euro 6-2 in Table 1 of Appendix 6 of Annex I to Regulation (EC) No 692/2008 shall be considered equivalent to the characters C and D of Table 1 of Appendix 9 of Annex I to this Regulation.’.

ANNEX III

Regulation (EU) 2017/1151 is corrected as follows:

(1)

Annex I is corrected as follows:

(a)

in point 2.4 Figure I.2.4 is replaced by the following:

‘Figure I.2.4

Application of test requirements for type-approval and extensions

a

Specific test procedures for hydrogen and flex fuel biodiesel vehicles will be defined at a later stage.

b

Particulate mass and particle number limits and respective measurement procedures shall apply only to vehicles with direct injection engines

c

When a bi-fuel vehicle is combined with a flex fuel vehicle, both test requirements are applicable.

d

Only NOx emissions shall be determined when the vehicle is running on hydrogen.

e

Further requirements for biodiesel will be defined later.’

Vehicle categoryVehicles with positive ignition engines including hybridsaVehicles with compression ignition engines including hybridsPure electric vehiclesHydrogen fuel cell vehicles
Mono fuelBi-fuelcFlex-fuelc
Reference fuel

Petrol

(E10)

LPGNG/BiomethaneHydrogen (ICE)Petrol (E10)Petrol (E10)Petrol (E10)Petrol (E10)

Diesel

(B7)e

—Hydrogen (Fuel Cell)
LPGNG/BiomethaneHydrogen (ICE)d

Ethanol

(E85)

Gaseous pollutants

(Type 1 test)

YesYesYesYesd

Yes

(both fuels)

Yes

(both fuels)

Yes

(both fuels)

Yes

(both fuels)

Yes——

PM

(Type 1 test)

Yesb———

Yesb

(petrol only)

Yesb

(petrol only)

Yesb

(petrol only)

Yesb

(both fuels)

Yes——
PNYesb———

Yesb

(petrol only)

Yesb

(petrol only)

Yesb

(petrol only)

Yesb

(both fuels)

Yes——
Gaseous pollutants, RDE (Type 1A test)YesYesYesYesd

Yes

(both fuels)

Yes

(both fuels)

Yes

(both fuels)

Yes

(both fuels)

Yes——
PN, RDE (Type 1A test)Yesb———

Yes

(both fuels)b

Yes

(both fuels)b

Yes

(both fuels)b

Yes

(both fuels)b

Yes——

Idle emissions

(Type 2 test)

YesYesYes—

Yes

(both fuels)

Yes

(both fuels)

Yes

(petrol only)

Yes

(both fuels)

———

Crankcase emissions

(Type 3 test)

YesYesYes—

Yes

(petrol only)

Yes

(petrol only)

Yes

(petrol only)

Yes

(petrol only)

———

Evaporative emissions

(Type 4 test)

Yes———

Yes

(petrol only)

Yes

(petrol only)

Yes

(petrol only)

Yes

(petrol only)

———

Durability

(Type 5 test)

YesYesYesYes

Yes

(petrol only)

Yes

(petrol only)

Yes

(petrol only)

Yes

(petrol only)

Yes——

Low temperature emissions

(Type 6 test)

Yes———

Yes

(petrol only)

Yes

(petrol only)

Yes

(petrol only)

Yes

(both fuels)

———
In-service conformityYesYesYesYes

Yes

(both fuels)

Yes

(both fuels)

Yes

(both fuels)

Yes

(both fuels)

Yes——
On-board diagnosticsYesYesYesYesYesYesYesYesYes——
CO2 emissions, fuel consumption, electric energy consumption and electric rangeYesYesYesYes

Yes

(both fuels)

Yes

(both fuels)

Yes

(both fuels)

Yes

(both fuels)

YesYesYes
Smoke opacity————————Yes——
Engine powerYesYesYesYesYesYesYesYesYesYesYes
(b)

Appendix 3 is corrected as follows:

(i)

the following points are inserted:

  • ‘3.5.7.2.1.1.0.Vehicle high (NEDC): …g/km’

  • ‘3.5.7.2.1.2.0.Vehicle low (if applicable) (NEDC): …g/km’

  • ‘3.5.7.2.2.1.0.Vehicle high (NEDC): …g/km’

  • ‘3.5.7.2.2.2.0.Vehicle low (if applicable) (NEDC): …g/km’

  • ‘3.5.7.2.2.3.0.Vehicle M (if applicable) (NEDC): …g/km’

  • ‘3.5.7.2.3.1.0.Vehicle high (NEDC): …g/km’

  • ‘3.5.7.2.3.2.0.Vehicle low (if applicable) (NEDC): …g/km’

  • ‘3.5.7.2.3.3.0.Vehicle M (if applicable) (NEDC): …g/km’;

(ii)

in point 3.5.8.3 the explanatory notes corresponding to the letters (w) to (w5) are deleted

(iii)

after the table in the model information document the following text is inserted:

‘Explanatory notes

(1)Delete where not applicable (there are cases where nothing needs to be deleted when more than one entry is applicable).

(2)Specify the tolerance.

(3)Please fill in here the upper and lower values for each variant.

(6)Vehicles can be fuelled with both petrol and a gaseous fuel but, where the petrol system is fitted for emergency purposes or starting only and of which the petrol tank cannot contain more than 15 litres of petrol, will be regarded for the test as vehicles which can only run a gaseous fuel.

(7)Optional equipment that affects the dimensions of the vehicle shall be specified.

(c)Classified according to the definitions set out in Part A of Annex II.

(f)Where there is one version with a normal cab and another with a sleeper cab, both sets of masses and dimensions are to be stated.

(g)Standard ISO 612: 1978 — Road vehicles — Dimensions of motor vehicles and towed vehicles — terms and definitions.

(h)The mass of the driver is assessed at 75 kg.

The liquid containing systems (except those for used water that must remain empty) are filled to 100 % of the capacity specified by the manufacturer.

The information referred to in points 2.6(b) and 2.6.1(b) do not need to be provided for vehicle categories N 2, N 3, M 2, M 3, O 3, and O 4.

(i)For trailers or semi-trailers, and for vehicles coupled with a trailer or a semi-trailer, which exert a significant vertical load on the coupling device or the fifth wheel, this load, divided by standard acceleration of gravity, is included in the maximum technically permissible mass.

(k)In the case of a vehicle that can run either on petrol, diesel, etc., or also in combination with another fuel, items shall be repeated.

In the case of non-conventional engines and systems, particulars equivalent to those referred to here shall be supplied by the manufacturer.

(l)This figure shall be rounded off to the nearest tenth of a millimetre.

(m)This value shall be calculated (π = 3,1416) and rounded off to the nearest cm3.

(n)Determined in accordance with the requirements of Regulation (EC) No 715/2007 or Regulation (EC) No 595/2009 as applicable.

(o)Determined in accordance with the requirements of Council Directive 80/1268/EEC (OJ L 375, 31.12.1980, p. 36).

(p)The specified particulars are to be given for any proposed variants.

(q)With respect to trailers, maximum speed permitted by the manufacturer.

(w)Eco-innovations.

(w1)Expand the table if necessary, using one extra row per eco-innovation.

(w2)Number of the Commission Decision approving the eco-innovation.

(w3)Assigned in the Commission Decision approving the eco-innovation.

(w4)Under agreement of the type-approval authority, if a modelling methodology is applied instead of the type 1 test cycle, this value shall be the one provided by the modelling methodology.

(w5)Sum of the CO2 emissions savings of each individual eco-innovation.’

(iv)

in the Appendix to information document, the table is replaced by the following:

‘VL (if existing)VHV representative (only for road load matrix family)

2.2.Vehicle bodywork type (variant/version)

2.2.Vehicle bodywork type (variant/version)

2.2.Vehicle bodywork type (variant/version)

2.3.Road load method used (measurement or calculation by road load family)

2.3.Road load method used (measurement or calculation by road load family)

2.3.Road load method used (measurement or calculation by road load matrix family)

2.4.Road load information from the test

2.4.Road load information from the test

2.4.Road load information from the test

2.4.1.Tyres make and type:

2.4.1.Tyres make and type:

2.4.1.Tyres make and type:

2.4.2.Tyre dimensions (front/rear):

2.4.2.Tyre dimensions (front/rear):

2.4.2.Tyre dimensions (front/rear):

2.4.4.Tyre pressure (front/rear) (kPa):

2.4.4.Tyre pressure (front/rear) (kPa):

2.4.4.Tyre pressure (front/rear) (kPa):

2.4.5.Tyre rolling resistance (front/rear) (kg/t):

2.4.5.Tyre rolling resistance (front/rear) (kg/t):

2.4.5.Tyre rolling resistance (front/rear) (kg/t) and RR class (A-G):

2.4.6.Vehicle test mass (kg):

2.4.6.Vehicle test mass (kg):

2.4.6.Vehicle test mass (kg):

2.4.7.Delta Cd.A compared to VH (m2)

2.4.8.Road load coefficient f0, f1, f2

2.4.8.Road load coefficient f0, f1, f2

2.4.8.Road load coefficient f0, f1, f2

2.4.9.Frontal area m2 (0,0000 m2)

2.4.10.Calculation tool information to calculate VH and VL road loads’

(c)

in Appendix 4, the ‘Addendum to EC type-approval certificate No …’ is corrected as follows:

(i)

in point 2.1, the following table is inserted after the table entitled ‘ATCT test’:

a

Where applicable.

b

Round to two decimal numbers.’;

‘ATCT test ResultCO(mg/km)THC(mg/km)NMHC(mg/km)NOx(mg/km)THC + NOx(mg/km)PM(mg/km)PN(#.1011/km)
Measureda b
(ii)

in point 2.1, the words ‘Type 4: … g/test’ are replaced by the words ‘Type 4: … g/test; test procedure in accordance with Annex VI to Regulation (EC) No 692/2008: Yes/No’;

(iii)

in the Appendix to the Addendum to the Type Approval Certificate, point 3 is replaced by the following:

‘3.Deviation and verification factors (determined in accordance with point 3.2.8 of Annex I to Implementing Regulations (EU) 2017/1152 and (EU) 2017/1153):

Deviation factor (if applicable)
Verification factor (if applicable)“1” or “0”
Hash identifier code of the correlation tool output report’
(d)

in Appendix 6, Table 1 is replaced by the following:

Table 1

a

This limitation does not apply if a vehicle was type-approved in accordance with the requirements of Regulation (EC) No 715/2007 and its implementing legislation prior to 1 September 2017 in the case of category M and N1 class I vehicles, or prior to 1 September 2018 in the case of category N1 class II and III and category N2 vehicles, according to the last subparagraph of Article 15(4).

Key:

“Euro 6-1” OBD standard

=

Full Euro 6 OBD requirements but with preliminary OBD threshold limits as defined in point 2.3.4 of Annex XI and partially relaxed IUPR;

“Euro 6-2” OBD standard

=

Full Euro 6 OBD requirements but with final OBD threshold limits as defined in point 2.3.3 of Annex XI;

“Euro 6b” emissions standard

=

Euro 6 emission requirements including revised measurement procedure for particulate matter, particle number standards (preliminary values for PI direct injection);

“Euro 6c” emissions standard

=

RDE NOx testing for monitoring only (no NTE emission limits applied), otherwise full Euro 6 tailpipe emission requirements (including PN RDE);

“Euro 6c-EVAP” emissions standard

=

RDE NOx testing for monitoring only (no NTE emission limits applied), otherwise full Euro 6 tailpipe emission requirements (including PN RDE), revised evaporative emissions test procedure;

“Euro 6d-TEMP” emissions standard

=

RDE NOx testing against temporary conformity factors, otherwise full Euro 6 tailpipe emission requirements (including PN RDE);

“Euro 6d-TEMP-EVAP” emissions standard

=

RDE NOx testing against temporary conformity factors, otherwise full Euro 6 tailpipe emission requirements (including PN RDE), revised evaporative emissions test procedure;

“Euro 6d” emissions standard

=

RDE testing against final conformity factors, otherwise full Euro 6 tailpipe emission requirements, revised evaporative emissions test procedure.’;

‘CharacterEmission standardOBD standardVehicle category and classEngineImplementation date: new typesImplementation date: new vehiclesLast date of registration
AAEuro 6cEuro 6-1M, N1 class IPI, CI31.8.2018
BAEuro 6bEuro 6-1M, N1 class IPI, CI31.8.2018
ABEuro 6cEuro 6-1N1 class IIPI, CI31.8.2019
BBEuro 6bEuro 6-1N1 class IIPI, CI31.8.2019
ACEuro 6cEuro 6-1N1 class III, N2PI, CI31.8.2019
BCEuro 6bEuro 6-1N1 class III, N2PI, CI31.8.2019
ADEuro 6cEuro 6-2M, N1 class IPI, CI1.9.201831.8.2019
AEEuro 6c-EVAPEuro 6-2N1 class IIPI, CI1.9.201931.8.2020
AFEuro 6c-EVAPEuro 6-2N1 class III, N2PI, CI1.9.201931.8.2020
AGEuro 6d-TEMPEuro 6-2M, N1 class IPI, CI1.9.2017a31.8.2019
BGEuro 6d-TEMP-EVAPEuro 6-2M, N1 class IPI, CI1.9.20191.9.201931.12.2020
AHEuro 6d-TEMPEuro 6-2N1 class IIPI, CI1.9.2018a31.8.2019
BHEuro 6d-TEMP-EVAPEuro 6-2N1 class IIPI, CI1.9.20191.9.202031.12.2021
AIEuro 6d-TEMPEuro 6-2N1 class III, N2PI, CI1.9.2018a31.8.2019
BIEuro 6d-TEMP-EVAPEuro 6-2N1 class III, N2PI, CI1.9.20191.9.202031.12.2021
AJEuro 6dEuro 6-2M, N1 class IPI, CI1.1.20201.1.2021
AKEuro 6dEuro 6-2N1 class IIPI, CI1.1.20211.1.2022
ALEuro 6dEuro 6-2N1 class III, N2PI, CI1.1.20211.1.2022
AXn.a.n.a.All vehiclesBattery full electric
AYn.a.n.a.All vehiclesFuel cell
AZn.a.n.a.All vehicles using certificates according to point 2.1.1 of Annex IPI, CI
(e)

Appendix 8b is corrected as follows:

(i)

in point 2.1.3, the following text is inserted before the table:

‘The manufacturer and the type approval authority shall agree which vehicle test model is representative.

The vehicle parameters test mass, tyre rolling resistance and frontal area of both a vehicle HM and LM shall be determined in such a way that vehicle HM produces the highest cycle energy demand and vehicle LM the lowest cycle energy demand from the road load matrix family. The manufacturer and the type approval authority shall agree on the vehicle parameters for vehicle HM and LM.

The road load of vehicles HM and LM of the road load matrix family shall be calculated according to paragraph 5.1 of Sub-Annex 4 of Annex XXI.’;

(ii)

in point 2.4.3, the words ‘Repeat §2.4.1. with the representative vehicle data if applicable’ are deleted;

(iii)

in point 2.6.1, the last row of the table ‘ROAD LOAD MATRIX (Annex XXI, Sub Annex 4, §5)’ is replaced by the following:

‘Final results

Torque method:

  • c0r =

  • c1r =

  • c2r =

and

  • f0r (calculated for vehicle HM) =

  • f2r (calculated for vehicle HM) =

  • f0r (calculated for vehicle LM) =

  • f2r (calculated for vehicle LM) =

Coastdown method:

  • f0r (calculated for vehicle HM) =

  • f2r (calculated for vehicle HM) =

  • f0r (calculated for vehicle LM) =

  • f2r (calculated for vehicle LM) =’.

(f)

in the table in Appendix 8c the first 4 rows are replaced by the following:

‘Adjustable wheel alignment parameters

Annex XXI, Sub-Annex 4, §4.2.1.8.3.

:
The coefficients, c0, c1 and c2,:

c0 =

c1 =

c2 =

The coastdown times measured on the chassis dynamometer

Annex XXI, Sub-Annex 4, §4.4.4.

:
Reference speed (km/h)Coastdown time (s)
130
120
110
100
90
80
70
60
50
40
30
20

Additional weight may be placed on or in the vehicle to eliminate tyre slippage

Annex XXI, Sub-Annex 4, §7.1.1.1.1.

:

weight (kg)

on/in the vehicle

The coastdown times after performing the vehicle coast down procedure according paragraph 4.3.1.3 of Annex XXI, Sub-Annex 4

Annex XXI, Sub-Annex 4, §8.2.4.2.

:
Reference speed (km/h)Coastdown time (s)
130
120
110
100
90
80
70
60
50
40
30
20’
(2)

Annex IIIA is corrected as follows:

(a)

point 3.1 is replaced by the following:

‘3.1.The following requirements apply to PEMS tests referred to in Article 3(11), second subparagraph.’

(b)

Appendix 6 is corrected as follows:

(i)

in point 2 the line corresponding to the symbol ‘aref’ is replaced by the following:

‘aref …Reference acceleration for Pdrive’;

(ii)

in point 2 the line corresponding to the symbol ‘TM’ is replaced by the following:

‘TM …Test mass of the vehicle’;

(iii)

in point 2 the line corresponding to the symbol ‘vref’ is replaced by the following:

‘vref …Reference velocity for Pdrive’;

(iv)

point 3.4.1 shall be replaced by the following:

‘3.4.1.The power classes and the corresponding time shares of the power classes in normal driving are defined for normalised power values to be representative for any LDV (Table 1-2).

Table 1-2
Normalised standard power frequencies for urban driving and for a weighted average for a total trip consisting of 1/3 urban, 1/3 road, 1/3 motorway mileage
Power class NoPc,norm,j [-]UrbanTotal trip
From >to ≤Time share, tC,j
1– 0,121,9700 %18,5611 %
2– 0,10,128,7900 %21,8580 %
30,1144,0000 %43,4582 %
411,94,7400 %13,2690 %
51,92,80,4500 %2,3767 %
62,83,70,0450 %0,4232 %
73,74,60,0040 %0,0511 %
84,65,50,0004 %0,0024 %
95,50,0003 %0,0003 %

The Pc,norm columns in Table 1-2 shall be de-normalised by multiplication with Pdrive, where Pdrive is the actual wheel power of the tested car in the type approval settings at the chassis dynamometer at vref and aref.

Pc,j [kW] = Pc,norm, j * Pdrive

Where:

  • j is the power class index according to Table 1

  • νref = 66 km/h

  • αref = 0,44 m/s2

  • The driving resistance coefficients f0, f1, f2 are the target WLTP road load values for the individual vehicle to be PEMS tested, as defined in point 2.4 of sub-Annex 4 of Annex XXI

  • TMWLTP is the WLTP test mass of the individual vehicle to be PEMS tested, as defined in point 3.2.25 of Annex XXI.’

(v)

point 3.4.2 is replaced by the following:

‘3.4.2. Correction of the wheel power classes

The maximum wheel power class to be considered is the highest class in Table 1 which includes (Prated × 0,9). The time shares of all excluded classes shall be added to the highest remaining class.

From each Pc,norm,j the corresponding Pc,j shall be calculated to define the upper and lower bounds in kW per wheel power class for the tested vehicle as shown in Figure 1.

Figure 1 Schematic picture for converting the normalised standardised power frequency into a vehicle specific power frequency

An example for this de-normalisation is given below.

Example for input data:

ParameterValue
f0 [N]86
f1 [N/(km/h)]0,8
f2 [N/(km/h)2]0,036
TM [kg]1 590
Prated [kW]120 (Example 1)
Prated [kW]75 (Example 2)

Corresponding results:

  • Pdrive = 66[km/h]/3,6 * (86 + 0,8[N/(km/h)] * 66[km/h] + 0,036[N/(km/h)] * (66[km/h])2 + 1 590[kg] * 0,44[m/s2]) * 0,001

  • Pdrive = 18,25 kW

Table 2

De-normalised standard power frequency values from Table 1 (for Example 1)

(1) The highest wheel power class to be considered is the one containing 0,9 × Prated. Here 0,9 × 120 = 108.
Power class NoPc,j [kW]UrbanTotal trip
From >to ≤Time share, tC,j [%]
1– 1,82521,97 %18,5611 %
2– 1,8251,82528,79 %21,8580 %
31,82518,24644,00 %43,4583 %
418,24634,6674,74 %13,2690 %
534,66751,0880,45 %2,3767 %
651,08867,5090,045 %0,4232 %
767,50983,9300,004 %0,0511 %
883,930100,3510,0004 %0,0024 %
9100,3510,00025 %0,0003 %

Table 3

De-normalised standard power frequency values from Table 1 (for Example 2)

a

The highest class wheel power class to be considered is the one containing 0,9 × Prated. Here 0,9 × 75 = 67,5.’;

Power class NoPc,j [kW]UrbanTotal trip
From >to ≤Time share, tC,j [%]
1All < – 1,825– 1,82521,97 %18,5611 %
2– 1,8251,82528,79 %21,8580 %
31,82518,24644,00 %43,4583 %
418,24634,6674,74 %13,2690 %
534,66751,0880,45 %2,3767 %
6a51,088All > 51,0880,04965 %0,4770 %
767,50983,930——
883,930100,351——
9100,351All > 100,375——
(3)

in Annex V, point 2.3 is replaced by the following:

‘2.3.The road load coefficients to be used shall be those for vehicle low (VL). If VL does not exist or the total load of vehicle (VH) at 80 km/h is higher than the total load of VL at 80 km/h + 5 %, then the VH road load shall be used. VL and VH are defined in point 4.2.1.2 of Sub-Annex 4 to Annex XXI. Alternatively the manufacturer may choose to use road loads that have been determined according to the provisions of Appendix 7 of Annex 4a of UN/ECE Regulation No 83 for a vehicle included in the interpolation family.’;

(4)

in Annex VI point 5.2.8 is replaced by the following:

‘5.2.8.As an exception to points 5.2.1 to 5.2.7 above, the Manufacturers using multilayer or metal tanks may choose to use the following assigned permeability factor (APF) instead of the complete measurement procedure mentioned above:

APF multilayer/metal tank = 120 mg/24 h’;

(5)

in Annex VII, point 3.10 is replaced by the following:

‘3.10.The road load coefficients to be used shall be those for vehicle low (VL). If VL low does not exist or the total load of vehicle (VH) at 80 km/h is higher than the total load of VL at 80 km/h + 5 %, then the VH road load shall be used. VL and VH are defined in point 4.2.1.2 of Sub-Annex 4 to Annex XXI.’;

(6)

in Annex VIII, point 3.3 is replaced by the following:

‘3.3.The road load coefficients to be used shall be those for vehicle low (VL). If VL low does not exist or the total load of vehicle (VH) at 80 km/h is higher than the total load of VL at 80 km/h + 5 %, then the VH road load shall be used. VL and VH are defined in point 4.2.1.2 of Sub-Annex 4 to Annex XXI. Alternatively the manufacturer may choose to use road loads that have been determined according to the provisions of Appendix 7 of Annex 4a of UN/ECE Regulation No 83 for a vehicle included in the interpolation family.’;

(7)

in Annex XII, point 5.4 is replaced by the following:

‘5.4.The manufacturer of the base vehicle shall test a vehicle representative of a completed multi-stage vehicle for road load determination. The manufacturer of the base vehicle shall calculate the road load coefficients of vehicle HM and LM of a road load matrix family as set in paragraph 5 of Sub-Annex 4 to Annex XXI and shall determine the CO2 emission and fuel consumption of both vehicles. The manufacturer of the base vehicle shall make available a calculation tool to establish, on the basis of the parameters of completed vehicles, the final fuel consumption and CO2 values as set in Sub-Annex 7 to Annex XXI.’;

(8)

Annex XXI is corrected as follows:

(a)

point 3.2.19 is replaced by the following:

‘3.2.19.“Target road load” means the road load to be reproduced on the chassis dynamometer.’;

(b)

Sub-Annex 4 is amended as follows:

(i)

in point 5.1.1.1, the line corresponding to the symbol ‘RR’ is replaced by the following:

‘RR is the tyre rolling resistance class value of the individual vehicle of the road load matrix family, kg/tonne;’;

(ii)

in point 5.1.2.1, the line corresponding to the symbol ‘RR’ is replaced by the following:

‘RR is the tyre rolling resistance class value of the individual vehicle of the road load matrix family, kg/tonne;’;

(iii)

in point 8.2, in the second paragraph, the last sentence is replaced by the following:

‘The target running resistance values are the values calculated using the method specified in paragraph 5.1 of this Sub-Annex.’;

(c)

in Sub-Annex 6a the following point 3.7.3 is inserted:

‘3.7.3.In particular, the tailpipe emissions measured at an ATCT test shall not be above the Euro 6 emission limits applicable to the vehicle tested defined in Table 2 of Annex I to Regulation (EC) No 715/2007.’.

Back to top

Options/Help

Print Options

Close

Legislation is available in different versions:

Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.

Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.

Close

Opening Options

Different options to open legislation in order to view more content on screen at once

Close

More Resources

Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:

  • the original print PDF of the as adopted version that was used for the EU Official Journal
  • lists of changes made by and/or affecting this legislation item
  • all formats of all associated documents
  • correction slips
  • links to related legislation and further information resources
Close

More Resources

Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:

  • the original print PDF of the as adopted version that was used for the print copy
  • correction slips

Click 'View More' or select 'More Resources' tab for additional information including:

  • lists of changes made by and/or affecting this legislation item
  • confers power and blanket amendment details
  • all formats of all associated documents
  • links to related legislation and further information resources

The data on this page is available in the alternative data formats listed: