- Latest available (Revised)
- Point in Time (01/04/2020)
- Original (As made)
Point in time view as at 01/04/2020.
There are currently no known outstanding effects for the The Public Water Supplies (Scotland) Regulations 2014.
Revised legislation carried on this site may not be fully up to date. At the current time any known changes or effects made by subsequent legislation have been applied to the text of the legislation you are viewing by the editorial team. Please see ‘Frequently Asked Questions’ for details regarding the timescales for which new effects are identified and recorded on this site.
Regulation 2(1) and (4)
1 The parametric values in Part 2 are not required to protect human health (since the parametric values in Part 1 are sufficient for that purpose). The values in Part 2 are not therefore set for the purposes of Article 5(3) of the Directive. | ||||
2 Compliance required as to 95% of samples from each service reservoir (regulation 4(4)). | ||||
(1)Item | (2)Parameter | (3)Concentration orvalue (maximum) | (4)Units ofmeasurement | (5)Point ofcompliance |
---|---|---|---|---|
Part 1 | ||||
1. | Enterococci | 0 | Number/100ml | Consumer's tap |
2. | Escherichia coli | 0 | Number/100ml | Consumer's tap |
Part 21 | ||||
3. | Coliform bacteria | 0 | Number/100ml | Service reservoir2 |
0 | Number/100ml | Treatment works | ||
4. | Escherichia coli | 0 | Number/100ml | Service reservoir |
0 | Number/100ml | Treatment works | ||
Notes— |
1 The parametric value refers to the residual monomer concentration in the water as calculated according to specifications of the maximum release from the corresponding polymer in contact with the water. This is controlled by product specification. | ||||
2 See also regulation 6(6). | ||||
3 See also regulation 4(2)(c). | ||||
4 The corresponding parametric value applies to each ‘other pesticide’ individually. | ||||
5 The parametric values in this Part are not required to protect human health (since the parametric values in Part 1 are sufficient for that purpose). The values in Part 2 are not therefore set for the purposes of Article 5(3) of the Directive. | ||||
(1)Item | (2)Parameter | (3)Concentration orvalue (maximum) | (4)Units ofmeasurement | (5)Point ofcompliance |
---|---|---|---|---|
Part 1 | ||||
1. | Acrylamide1 | 0.10 | μg/l | Consumer's tap |
2. | Antimony | 5.0 | μgSb/l | Consumer's tap |
3. | Arsenic | 10 | μgAs/l | Consumer's tap |
4. | Benzene | 1.0 | μg/l | Consumer's tap |
5. | Benzo(a)pyrene | 0.010 | μg/l | Consumer's tap |
6. | Boron | 1.0 | mgB/l | Consumer's tap |
7. | Bromate | 10 | μgBrO3/l | Consumer's tap |
8. | Cadmium | 5.0 | μgCd/l | Consumer's tap |
9. | Chromium | 50 | μgCr/l | Consumer's tap |
10. | Copper2 | 2.0 | mgCu/l | Consumer's tap |
11. | Cyanide | 50 | μgCN/l | Consumer's tap |
12. | 1,2-dichloroethane | 3.0 | μg/l | Consumer's tap |
13. | Epichlorohydrin1 | 0.10 | μg/l | Consumer's tap |
14. | Fluoride | 1.5 | mgF/l | Consumer's tap |
15. | Lead2 | 10 | μgPb/l | Consumer's tap |
16. | Mercury | 1.0 | μgHg/l | Consumer's tap |
17. | Nickel2 | 20 | μgNi/l | Consumer's tap |
18. | Nitrate3 | 50 | mgNO3/l | Consumer's tap |
19. | Nitrite3 | 0.50 | mgNO2/l | Consumer's tap |
0.10 | mgNO2/l | Treatment works | ||
20. | Pesticide— | |||
Aldrin | 0.030 | μg/l | Consumer's tap | |
Dieldrin | 0.030 | μg/l | Consumer's tap | |
Heptachlor | 0.030 | μg/l | Consumer's tap | |
Heptachlor epoxide | 0.030 | μg/l | Consumer's tap | |
Other pesticide4 | 0.10 | μg/l | Consumer's tap | |
21. | Pesticides: Total | 0.50 | μg/l | Consumer's tap |
22. | PAH: Total | 0.10 | μg/l | Consumer's tap |
23. | Selenium | 10 | μgSe/l | Consumer's tap |
24. | Tetrachloroethene and Trichloroethene | 10 | μg/l | Consumer's tap |
25. | THM: Total | 100 | μg/l | Consumer's tap |
26. | Vinyl chloride1 | 0.50 | μg/l | Consumer's tap |
Part 25 | ||||
27. | Aluminium | 200 | μgAl/l | Consumer's tap |
28. | Colour | 20 | mg/l Pt/Co | Consumer's tap |
29. | Iron | 200 | μgFe/l | Consumer's tap |
30. | Manganese | 50 | μgMn/l | Consumer's tap |
31. | Sodium | 200 | mgNa/l | Consumer's tap |
32. | Tetrachloromethane | 3 | μg/l | Consumer's tap |
33. | Turbidity | 4 | NTU | Consumer's tap |
Notes— |
1 The water should not be aggressive. | ||||
2 In the event that the use of samples from a point within a water supply zone has not been authorised for this parameter under regulation 8, the point of monitoring is instead the consumer's tap. | ||||
3 This value, in so far as the point of monitoring is a service reservoir, is not set for the purposes of Article 5(3) of the Directive. | ||||
4 This value, in so far as the point of monitoring is a treatment works, is not set for the purposes of Article 5(3) of the Directive. | ||||
[F15 Remedial action is to be deemed justified on radiological protection grounds, without further consideration, where radon concentrations exceed 1,000 Bq/l.] | ||||
[F16 If the concentration of tritium exceeds this value, an analysis of the presence of other artificial radionuclides must be also carried out by Scottish Water.] | ||||
(1)Item | (2)Parameter | (3)Concentration orvalue (maximum)or state | (4)Units ofmeasurement | (5)Point ofmonitoring |
---|---|---|---|---|
Part 1 | ||||
1. | Ammonium | 0.50 | mgNH4/l | Consumer's tap |
2. | Chloride1 | 250 | mgCl/l | Supply point2 |
3. | Clostridium perfringens (including spores) | 0 | Number/100ml | Supply point2 |
4. | Coliform bacteria | 0 | Number/100ml | Consumer's tap |
5. | Colony count | No abnormal change | Number/1ml at 22°C and at 37°C | Consumer's tap |
Service reservoir3 | ||||
Treatment works4 | ||||
6. | Colour | Acceptable to consumers and no abnormal change | Consumer's tap | |
7. | Conductivity1 | 2500 | μS/cm at 20°C | Supply point2 |
8. | Hydrogen ion | 9.5 | pH value | Consumer's tap |
6.5 (minimum) | ||||
9. | Odour | Acceptable to consumers and no abnormal change | Consumer's tap | |
10. | Sulphate1 | 250 | mgSO4/l | Supply point2 |
11. | Taste | Acceptable to consumers and no abnormal change | Consumer's tap | |
12. | Total organic carbon | No abnormal change | mgC/l | Supply point2 |
13. | Turbidity | 1 | NTU | Treatment works |
Part 2 | ||||
14. | Indicative dose | 0.10 | mSvF2... | Supply point2 |
[F3 14A. | Radon5 | 100 | Bq/l | Supply point(b)] |
15. | Tritium [F4(f)] | 100 | Bq/l | Supply point2 |
Notes— |
Textual Amendments
F1Words in sch. 1 inserted (28.11.2015) by The Private and Public Water Supplies (Miscellaneous Amendments) (Scotland) Regulations 2015 (S.S.I. 2015/346), regs. 1(1), 16(b)
F2Word in sch. 1 omitted (28.11.2015) by virtue of The Private and Public Water Supplies (Miscellaneous Amendments) (Scotland) Regulations 2015 (S.S.I. 2015/346), regs. 1(1), 16(a)(i)
F3Sch. 1 entry inserted (28.11.2015) by The Private and Public Water Supplies (Miscellaneous Amendments) (Scotland) Regulations 2015 (S.S.I. 2015/346), regs. 1(1), 16(a)(ii)
F4Word in sch. 1 inserted (28.11.2015) by The Private and Public Water Supplies (Miscellaneous Amendments) (Scotland) Regulations 2015 (S.S.I. 2015/346), regs. 1(1), 16(a)(iii)
In this Schedule—
F5...
“NTU” means Nephelometric Turbidity Unit;
“PAH: Total” means the sum of the concentrations of the following polyaromatic hydrocarbons: benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(ghi)perylene and indeno(1,2,3-cd)pyrene;
“Pesticide” means an organic insecticide, herbicide, fungicide, nematocide, acaricide, algicide, rodenticide, slimicide, molluscicide or related product (including a growth regulator), and includes the relevant metabolites, degradation and reaction products of that pesticide;
“Pesticides: Total” refers to the sum of the concentrations of each pesticide detected and quantified in the monitoring procedure;
“Tetrachloroethene and Trichloroethene” means the sum of the concentrations of tetrachloroethene and trichloroethene; and
“THM: Total” means the sum of the concentrations of the following trihalomethanes: chloroform, bromoform, dibromochloromethane and bromodichloromethane.
Textual Amendments
F5Words in sch. 1 omitted (28.11.2015) by virtue of The Private and Public Water Supplies (Miscellaneous Amendments) (Scotland) Regulations 2015 (S.S.I. 2015/346), regs. 1(1), 16(c)
Regulation 6(2) and (3)
Textual Amendments
F6Sch. 1A inserted (27.10.2017) by The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), reg. 1(1), sch. 1 (as amended by The Public and Private Water Supplies (Miscellaneous Amendments) (Scotland) Regulations 2017 (S.S.I. 2017/321), regs. 1, 3(2))
1. Each monitoring programme must—S
(a)verify that—
(i)the measures in place to control risks to human health throughout the water supply chain (from the catchment area through abstraction, treatment and storage to distribution) are working effectively; and
(ii)water at the point of compliance meets the water quality standards;
(b)provide information on the quality of water supplied to demonstrate that—
(i)the water quality standards are being met; and
(ii)the prescribed concentration or value for each parameter in Table C is not being exceeded at the point of monitoring for the parameter; and
(c)identify the most appropriate means of mitigating the risks to human health.
2.—(1) Each monitoring programme must fulfil the requirements of Part B of this schedule (and, where applicable, Part C of this schedule) by means of—S
(a)the collection and analysis of the quality of discrete water samples; or
(b)measurements of the quality of water recorded by a continuous monitoring process.
(2) In addition, monitoring programmes may consist of—
(a)inspections of records of the functionality and maintenance status of equipment; and
(b)inspections of the catchment area, water abstraction, treatment, storage and distribution infrastructure.
3. Scottish Water must ensure that each monitoring programme prepared by it is reviewed on a continuous basis, and updated or reconfirmed at least every 5 years.S
1.—(1) Each monitoring programme must take into account—S
(a)each parameter; and
(b)any other micro-organism, parasite or substance which needs to be monitored by virtue of regulation 5(2) or (3),
including those that are important for assessing the impact of any part of the public water supply system on the quality of water at a point of compliance.
(2) When choosing appropriate parameters and other micro-organisms, parasites or substances for monitoring (as required by, or in accordance with, this schedule), local conditions for the parts of the public water supply system in question must be taken into consideration.
2.—(1) The following parameters (“Group A parameters”) must be monitored at least at the minimum frequencies determined in accordance with the table in paragraph 3:—S
(a)Escherichia coli, coliform bacteria, colony count 22 °C, colour, turbidity, taste, odour, hydrogen ion concentration (pH), and conductivity; and
(b)any other parameter, or other micro-organism, parasite or substance, (except radon, tritium and indicative dose) identified as relevant in the monitoring programme—
(i)by virtue of regulation 5(2) (as read with regulation 6(2)(a)); or
(ii)where relevant, through a risk assessment.
(2) Ammonium and nitrite must be included as Group A parameters, if chloramination is used.
(3) Aluminium and iron must be included as Group A parameters, if used as water treatment chemicals.
(4) Aluminium, iron and manganese must be included as Group A parameters, if the water in question originates from, or is influenced by surface waters.
3.—(1) Other parameters, except radon, tritium and indicative dose, (“Group B parameters”) must be monitored at least at the frequencies determined in accordance with the table below.S
(2) In the table, “Group A parameters” is to be construed in accordance with paragraph 2.
Volume of water (in m3) distributed or produced each day within a water supply zone (Notes 1 and 2) | Group A parameters: number of samples per year | Group B parameters: number of samples per year | |
---|---|---|---|
> 0 | ≤ 10 | 2 | 1 |
> 10 | ≤ 1,000 | 4 | 1 |
> 1,000 | ≤ 10,000 | 4 for the first 1,000 m3/day of the total volume, plus 3 for each additional 1,000 m3/day and part thereof | 1 for the first 1,000 m3/day of the total volume, plus 1 for each additional 4,500 m3/day and part thereof |
> 10,000 | ≤ 100,000 | 4 for the first 1,000 m3/day of the total volume, plus 3 for each additional 1,000 m3/day and part thereof | 3 for the first 10,000 m3/day of the total volume, plus 1 for each additional 10,000 m3/day and part thereof |
> 100,000 | 4 for the first 1,000 m3/day of the total volume, plus 3 for each additional 1,000 m3/day and part thereof | 12 for the first 100,000 m3/day of the total volume, plus 1 for each additional 25,000 m3/day and part thereof | |
Note 1: The volumes are calculated as averages taken over a year. | |||
Note 2: The number of inhabitants in a water supply zone may be used instead of the volume of water to determine the minimum frequency, assuming water consumption of 200 litres/day per person. |
1. Scottish Water may (or, where required, must), in accordance with this Part, deviate from the requirements of paragraphs 2 and 3 in Part B of this schedule.S
2. Based on the results of a risk assessment, the list of parameters in Part B of this schedule (including any micro-organism, parasite or substance referred to in paragraph 2(1)(b) of that Part), must be extended and/or the minimum sampling frequencies under that Part increased if—S
(a)the list of parameters or frequencies required to be monitored under that Part B is not sufficient to fulfil the obligations imposed by regulation 5(1), (3) and (4);
(b)additional monitoring is required by regulation 5(2); or
(c)this is necessary to verify the matters in paragraph 1(a) of Part A of this schedule.
3. Subject to paragraph 4, based on the results of a risk assessment the list of parameters in Part B of this schedule (including any micro-organism, parasite or substance referred to in paragraph 2(1)(b) of that Part) and the sampling frequencies under that Part B may be reduced, provided that the following conditions are met:—S
(a)the frequency of sampling for Escherichia coli must not be reduced below the minimum frequency required by that Part B; and
(b)for other parameters in the list—
(i)the location and frequency of sampling must be determined in relation to the parameter’s origin, as well as the variability and long-term trend of its concentration, taking into account the water quality standards;
(ii)to reduce the minimum sampling frequency for a parameter under Part B of this schedule, the results obtained from samples collected at regular intervals over a period of at least 3 years from sampling points representative of the whole water supply zone must all be less than 60 % of the prescribed concentration or value for the parameter;
(iii)to remove a parameter from the list of parameters to be monitored under Part B of this schedule, the results obtained from samples collected at regular intervals over a period of at least 3 years from points representative of the whole water supply zone must all be less than 30 % of the prescribed concentration or value of the parameter; and
(iv)the removal of a parameter from the list of parameters to be monitored under Part B of this schedule must be based on the result of the risk assessment, informed by the results of monitoring of sources of water and confirming that human health is protected from the adverse effects of any contamination of water.
4.—(1) The minimum sampling frequency for a parameter under Part B of this schedule (including for a micro-organism, parasite or substance referred to in paragraph 2(1)(b) of that Part) may be reduced under paragraph 3(b)(ii) only if the risk assessment confirms that no factor (that can be reasonably anticipated) is likely to cause deterioration of the quality of the water.S
(2) Any such parameter may be removed from the list of parameters to be monitored under paragraph 3(b)(iii) only if—
(a)the risk assessment confirms that no factor (that can be reasonably anticipated) is likely to cause deterioration of the quality of the water; and
(b)the Drinking Water Quality Regulator for Scotland, by notice to Scottish Water, consents to the removal of the parameter from the list of parameters to be monitored in relation to a supply of water (or in relation to more than one supply of water), and that consent has not been revoked under sub-paragraph (4).
(3) The Drinking Water Quality Regulator for Scotland may not consent, under paragraph (2)(b), to the removal of any of the following from the list of parameters to be monitored:—
(a)enterococci, Escherichia coli, coliform bacteria, colony count 22 °C, colour, turbidity or hydrogen ion concentration (pH);
(b)iron, lead or manganese;
(c)where the water is supplied to premises within a nitrate vulnerable zone, nitrate; or
(d)any other parameter, or other micro-organism, parasite or substance, identified (for the time being) as relevant in the monitoring programme in relation to a supply of water—
(i)by virtue of regulation 5(2); or
(ii)where relevant, through a risk assessment.
(4) The Drinking Water Quality Regulator for Scotland may, by notice to Scottish Water, revoke with immediate effect any consent given by it under sub-paragraph (2)(b).
(5) In sub-paragraph (3) “nitrate vulnerable zone” means any area of land designated as a nitrate vulnerable zone by regulation 2 of the Designation of Nitrate Vulnerable Zones (Scotland) Regulations 2015.
1.—(1) Sampling points, in relation to water, must be determined by Scottish Water so as to ensure that the results of the analysis of discrete water samples collected at those points will establish whether or not the water meets the water quality standards at each point of compliance.S
(2) In the case of a supply of water in pipes to any premises used for a commercial or public activity, the sampling points must include a point of compliance within each premises.
(3) In the case of a supply of water in pipes to premises (including any premises used for a commercial or public activity), Scottish Water may take samples of the water within the water supply zone or at a treatment works for a particular parameter—
(a)if it can be demonstrated that there would be no adverse change to the measured value of the parameter concerned; and
(b)in the case of any premises used for a commercial or public activity, the Drinking Water Quality Regulator for Scotland, by notice to Scottish Water, consents to the samples being taken within the water supply zone or at the treatment works for the particular parameter, and that consent has not been revoked under sub-paragraph (6).
(4) In a case where Scottish Water may take samples of the water within the water supply zone or at a treatment works for a particular parameter, the point at which the samples are taken is to be treated for the purposes of these Regulations as the point of compliance for the parameter.
(5) As far as possible, the number of samples must be distributed equally in time and location.
(6) The Drinking Water Quality Regulator for Scotland may, by notice to Scottish Water, revoke with immediate effect any consent given by it under sub-paragraph (3)(b).
2. Subject to paragraph 1, sampling at the point of compliance must meet the following requirements:—S
(a)a sample for copper, lead or nickel must be taken at the consumer’s tap without prior flushing;
(b)a sample for any such parameter or any other chemical parameter must—
(i)be a random daytime sample of one litre volume; or
(ii)use a fixed stagnation time method that better reflects the national situation, provided that, at the water supply zone level, this does not result in fewer cases of non-compliance than using the random daytime method; and
(c)a sample for microbiological parameters at the point of compliance must be taken and handled in accordance with sampling purpose B of European standard EN ISO 19458:2006 entitled “Water quality - Sampling for microbiological analysis (ISO 19458:2006)”.
3. Sampling of water in a public water supply system, with the exception of sampling at the consumer’s tap, must be in accordance with international standard ISO 5667-5:2006 entitled “Water quality. Sampling. Guidance on sampling of drinking water from treatment works and piped distribution systems”.S
4. For microbiological parameters, sampling of water in a public water supply system must be taken and handled in accordance with sampling purpose A of European standard EN ISO 19458:2006 entitled “Water quality - Sampling for microbiological analysis (ISO 19458:2006)”.S
1.—(1) Subject to sub-paragraph (2), Scottish Water in relation to a supply of water must ensure that the water is monitored for radon, tritium and indicative dose.
(2) Where the Scottish Ministers, by notice to Scottish Water, confirm that they have established that radon, tritium or, as the case may be, indicative dose is not likely to be present in relation one or more supplies of water, for a period specified in the notice, in concentrations which could exceed the prescribed concentration or value for the parameter, Scottish Water is not required to monitor any such supply of water for the parameter during the period specified.
(3) In case of naturally occurring radionuclides—
(a)where previous results show that the concentration of radionuclides in one or more supplies of water is stable, the minimum sampling and analysis frequencies are to be decided by the Scottish Ministers, and confirmed by notice to Scottish Water, taking into consideration the risk to human health; and
(b)where the Scottish Ministers, by notice to Scottish Water, confirm that they are satisfied (on the basis of representative surveys, monitoring data or other reliable information) that levels of radon, tritium and the calculated indicative dose in one or more supplies of water will, for a period specified in the notice, remain below the prescribed concentration or value for each of these parameters at the point of compliance, Scottish Water is not required to monitor any such supply for these parameters during the period specified.
(4) Where sub-paragraph (3)(b) applies, the Scottish Ministers must communicate the grounds for the decision to the European Commission and provide the Commission with the necessary documentation supporting that decision, including the findings of any surveys, monitoring or investigations carried out.
2.—(1) Subject to paragraphs 5 and 6, Scottish Water must ensure that representative surveys are undertaken to determine the scale and nature of likely exposures to radon in the water originating from different types of ground water sources and wells in different geological areas.
(2) The surveys must be designed in such a way that underlying factors, and especially the geology and hydrology of the area, radioactivity of rock or soil, and well type, can be identified and used to direct further action to areas of likely high exposure.
(3) Monitoring of radon concentrations must be carried out if Scottish Water has reason to believe, on the basis of the results of the representative surveys or other reliable information, that the prescribed concentration or value for radon might be exceeded.
3.—(1) Subject to paragraphs 5 and 6, Scottish Water must monitor the water for tritium where—
(a)an anthropogenic source of tritium or other artificial radionuclides is present within the catchment area for the supply; and
(b)it cannot be shown on the basis of other surveillance programmes or investigations that the level of tritium is below the prescribed concentration or value for tritium.
(2) Where monitoring for tritium is required by sub-paragraph (1), samples must be taken in accordance with paragraph 6.
(3) If the concentration of tritium in any such sample exceeds the prescribed concentration or value for tritium, Scottish Water must carry out an investigation of the presence of other artificial radionuclides.
4.—(1) Scottish Water must monitor the water for indicative dose where—
(a)a source of artificial radioactivity or elevated natural radioactivity is present; and
(b)it cannot be shown on the basis of other representative monitoring programmes or other investigations that the indicative dose is below the prescribed concentration or value for that parameter.
(2) Where sub-paragraph (1) requires monitoring (of radionuclide levels) only in relation to a source of artificial radioactivity, samples must be taken in accordance with paragraph 6.
(3) Where sub-paragraph (1) requires monitoring (of radionuclide levels) in relation to a source of elevated natural radioactivity, Scottish Water must determine the frequency of the monitoring required of—
(a)gross alpha activity;
(b)gross beta activity; or
(c)individual natural radionuclides,
depending on the screening strategy adopted pursuant to Part F of this schedule.
(4) Where sub-paragraph (3) applies, the frequency determined may vary from a single check measurement to the frequency which would otherwise apply by virtue of paragraph 6.
(5) Where a single check for natural radioactivity is specified under sub-paragraph (3), Scottish Water must carry out a further check if any change occurs in relation to the supply which is likely to influence the concentrations of radionuclides in the supply.
5. Where the water is treated to reduce the level of radionuclides, Scottish Water must monitor the water for indicative dose, radon and tritium in accordance with paragraph 6 to verify the continued efficacy of that treatment.
6. The minimum sampling and analysis frequency for the monitoring of radon, tritium and indicative dose in water (where required by this schedule) from a public water supply system or from a tanker or used in a food production undertaking is set out in the following table.
Volume of water (in m3) distributed or produced each day within a water supply zone (Note 1) | Number of samples per year (Notes 2 and 3) | |
---|---|---|
> 0 | ≤ 100 | 1 |
> 100 | ≤ 1,000 | 1 |
> 1,000 | ≤ 10,000 | 1, plus 1 for each 3,300 m3/day and part thereof of the total volume |
> 10,000 | ≤ 100,000 | 3, plus 1 for each 10,000 m3/day and part thereof of the total volume |
> 100,000 | 10, plus 1 for each 25,000 m3/day and part thereof of the total volume | |
Note 1: The volumes are calculated as averages taken over a year. The number of inhabitants in a water supply zone may be used instead of the volume of water to determine the minimum frequency, assuming water consumption of 200 litres/day per person. | ||
Note 2: As far as possible, the number of samples must be distributed equally in time and location. | ||
Note 3: In the event of intermittent short-term supply the monitoring frequency of water distributed by tankers must be decided by Scottish Water in relation to the water. |
7. Where the prescribed concentration or value for radon, tritium or, as the case may be, indicative dose is exceeded in a sample of the water, the Drinking Water Quality Regulator for Scotland must specify, by notice to Scottish Water, the extent of resampling necessary to ensure that the measured values are representative of an average activity concentration for a full year.
1.—(1) Scottish Water, in relation to water, may use reliable screening strategies to indicate the presence of radioactivity in the water.
(2) These strategies may include screening for—
(a)certain radionuclides or an individual radionuclide; or
(b)gross alpha activity or gross beta activity.
2.—(1) Where screening of the water is carried out for certain radionuclides or for an individual radionuclide, Scottish Water must carry out an analysis of additional radionuclides if, in relation to any supply referred to in paragraph 1—
(a)one of the activity concentrations of a radionuclide referred to in the second column of the table below exceeds 20% of the corresponding derived concentration in the third column; or
(b)the tritium concentration exceeds the prescribed concentration or value for tritium.
(2) Scottish Water must, in deciding which radionuclides require to be measured for each supply, take into account all relevant information about likely sources of radioactivity.
Origin | Radionuclide (Note 1) | Derived concentration (Bq/1) | Notes |
---|---|---|---|
Natural | U-238 | 3.0 | Note 2 |
U-234 | 2.8 | Note 2 | |
Ra-226 | 0.5 | ||
Ra-228 | 0.2 | ||
Pb-210 | 0.2 | ||
Po-210 | 0.1 | ||
Artificial | C-14 | 240 | |
Sr-90 | 4.9 | ||
Pu-239 / Pu-240 | 0.6 | ||
Am-241 | 0.7 | ||
Co-60 | 40 | ||
Cs-134 | 7.2 | ||
Cs-137 | 11 | ||
I-131 | 6.2 | ||
Note 1: This table includes values for the most common natural and artificial radionuclides. These are precise values, calculated for a dose of 0.1 mSv, an annual intake of 730 litres and using the dose coefficients laid down in Table (A) of Annex III to Council Directive 96/29/Euratom laying down basic safety standards for the protection of the health of workers and the general public against the dangers arising from ionizing radiation. Derived concentrations for other radionuclides may be calculated on the same basis. | |||
Note 2: This allows only for the radiological properties of uranium, not for its chemical toxicity. |
3.—(1) Scottish Water may use screening strategies for gross alpha activity and gross beta activity (or, where appropriate, residual beta activity after subtraction of the potassium-40 activity) to monitor the water for indicative dose.
(2) Subject to sub-paragraph (3), screening levels must be set at—
(a)0.1 Bq/l for gross alpha activity; and
(b)1.0 Bq/l for gross beta activity.
(3) Scottish Water may set alternative levels to those specified in sub-paragraph (2) if it can demonstrate that these will ensure that an indicative dose of 0.1 mSv is not exceeded.
(4) If the gross alpha activity is less than 0.1 Bq/l and the gross beta activity is less than 1.0 Bq/l, Scottish Water may assume that the indicative dose is less than 0.1 mSv.
(5) Where sub-paragraph (4) applies, Scottish Water is not required to carry out a radiological investigation unless it is aware—
(a)that specific radionuclides are present in the water; and
(b)that these are liable to cause an indicate dose in excess of 0.1 mSv.
(6) If the gross alpha activity exceeds 0.1 Bq/l or the gross beta activity exceeds 1.0 Bq/l, Scottish Water must carry out an analysis for specific radionuclides.
(7) Scottish Water must, in deciding which radionuclides require to be measured for the purposes of sub-paragraph (6), take into account all relevant information about likely sources of radioactivity.
(8) If elevated levels of tritium are detected in a sample, Scottish Water must also measure the gross alpha activity and gross beta activity in that sample.
4.—(1) The indicative dose must be calculated from—
(a)the measured radionuclide concentrations and the dose coefficients laid down in Table (A) of Annex III to Council Directive 96/29/Euratom laying down basic safety standards for the protection of the health of workers and the general public against the dangers arising from ionizing radiation; or
(b)more recent information recognised by the Scottish Ministers,
on the basis of an annual intake of water of 730 litres for adults.
(2) Where the following formula is satisfied, Scottish Water may assume that the indicative dose is less than 0.1 mSv and that no further investigation is required:—
where—
“Ci (obs)” refers to the observed concentration of radionuclide “i”;
“Ci (der)” refers to derived concentration of radionuclide “i”; and
“n” refers to the number of radionuclides detected.]
Regulations 2(1), 2(4), 9 and 11
Textual Amendments
F7Sch. 2 heading substituted (27.10.2017) by The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 8(a)
Textual Amendments
F8Sch. 2 Table 1 omitted (27.10.2017) by virtue of The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 8(b)(i)
F9. . . | ||||
F9. . . | ||||
F9. . . | ||||
F9. . . | ||||
F9. . . | ||||
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | ||
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | ||
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | F9. . . | F9. . . | F9. . . |
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . | F9. . . | |||
F9. . . |
Textual Amendments
F9Sch. 2 Table 2 and notes omitted (27.10.2017) by virtue of The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 8(b)(ii)
F10. . . | ||||
F10. . . | ||||
F10. . . | ||||
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | ||
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | F10. . . | F10. . . | F10. . . |
F10. . . | F10. . . | |||
F10. . . | F10. . . | |||
F10. . . | F10. . . | |||
F10. . . | F10. . . | |||
F10. . . | F10. . . | |||
F10. . . | F10. . . | |||
F10. . . | F10. . . | |||
F10. . . | F10. . . | |||
F10. . . | F10. . . | |||
F10. . . |
Textual Amendments
F10Sch. 2 Table 3 and notes omitted (27.10.2017) by virtue of The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 8(b)(iii)
1 Sampling at the frequencies specified in this table for [F11item 5] is required only when chloramination is practised. When this is not the case, this parameter must be sampled instead at the frequencies specified in this table for [F12item 7] . | ||||
(1)Item | (2)Parameter | (3)Volume of watersupplied m3/d | (4)Reduced | (5)Standard |
---|---|---|---|---|
F13... | ||||
1. | Coliform bacteria | < 20 | – | 4 |
2. | Colony count | 20-1,999 | 12 | 52 |
3. | Escherichia coli | 2,000-5,999 | 52 | 104 |
4. | Residual disinfectant | 6,000-11,999 ≥12,000 | 104 208 | 208 365 |
5. | Nitrite1 | < 20 | – | 2 |
6. | Turbidity | 20-999 | 2 | 4 |
1,000-1,999 | 6 | 12 | ||
2,000-5,999 | 12 | 24 | ||
6,000-9,999 | 18 | 36 | ||
10,000-15,999 | 26 | 52 | ||
16,000-32,999 | 52 | 104 | ||
33,000-49,999 | 78 | 156 | ||
50,000-67,999 | 104 | 208 | ||
68,000-84,999 | 130 | 260 | ||
85,000-101,999 | 156 | 312 | ||
102,000-119,999 | 183 | 365 | ||
120,000-241,999 | 365 | 730 | ||
242,000-484,999 | 730 | 1,460 | ||
485,000-728,999 | 1,095 | 2,190 | ||
F14... | ||||
7. | Nitrite1 | < 20 | – | 1 |
20-999 | – | 4 | ||
1,000-49,999 | – | 8 | ||
50,000-89,999 | – | 12 | ||
90,000-299,999 | – | 24 | ||
300,000-649,999 | – | 36 | ||
≥650,000 | – | 48 | ||
Notes— |
Textual Amendments
F11Words in sch. 2 Table 4 Notes substituted (27.10.2017) by The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 8(d)(i)
F12Words in sch. 2 Table 4 Notes substituted (27.10.2017) by The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 8(d)(ii)
F13Words in sch. 2 Table 4 omitted (27.10.2017) by virtue of The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 8(c)(i)
F14Words in sch. 2 Table 4 omitted (27.10.2017) by virtue of The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 8(c)(ii)
Marginal Citations
M1This table specifies the number of samples to be taken at treatment works for the purposes of regulation 11.
In this Schedule F15... “Pesticide”, “PAH: Total”, “Tetrachloroethene and Trichloroethene” and “THM: Total” have the same meanings as they have in Schedule 1.
Textual Amendments
F15Words in sch. 2 omitted (28.11.2015) by virtue of The Private and Public Water Supplies (Miscellaneous Amendments) (Scotland) Regulations 2015 (S.S.I. 2015/346), regs. 1(1), 17(c)
Regulation 6(6A)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Textual Amendments
F16Sch. 2A omitted (27.10.2017) by virtue of The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 9
Regulation 14A(1) and (2)
Textual Amendments
F17Sch. 3 substituted (27.10.2017) by The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), reg. 1(1), sch. 2 (as amended by The Public and Private Water Supplies (Miscellaneous Amendments) (Scotland) Regulations 2017 (S.S.I. 2017/321), regs. 1, 3(3)(a)(b))
1.—(1) Scottish Water must ensure that the methods of analysis used for the purposes of monitoring and demonstrating compliance with these Regulations are validated and documented in accordance with European standard EN ISO/IEC 17025:2005 entitled “General requirements for the competence of testing and calibration laboratories (ISO/IEC 17025:2005)”, or other equivalent standards accepted at international level.S
(2) Scottish Water must ensure that laboratories or parties contracted by laboratories apply quality management system practices in accordance with European standard EN ISO/IEC 17025:2005 entitled “General requirements for the competence of testing and calibration laboratories (ISO/IEC 17025:2005)”, or other equivalent standards accepted at international level.
2. In the absence of an analytical method meeting the minimum performance criteria set out in Part B of this schedule, Scottish Water must ensure that monitoring is carried out using best available techniques not entailing excessive costs.S
1.—(1) Subject to sub-paragraph (2), the methods in paragraph 2 are given for reference.S
(2) Scottish Water may use other methods, providing the provisions of regulation 14A are met.
2. The methods for microbiological parameters are—S
(a)for Escherichia coli and coliform bacteria—
(i)European standard EN ISO 9308-1:2014 entitled “Water quality - Enumeration of Escherichia coli and coliform bacteria - Part 1: Membrane filtration method for waters with low bacterial background flora (ISO 9308-1:2014)”; or
(ii)European standard EN ISO 9308-2:2014 entitled “Water quality - Enumeration of Escherichia coli and coliform bacteria - Part 2: Most probable number method (ISO 9308-2:2012)”;
(b)for enterococci, European standard EN ISO 7899-2:2000 entitled “Water quality - Detection and enumeration of intestinal enterococci - Part 2: Membrane filtration method (ISO 7899-2:2000)”;
(c)for Pseudomonas aeruginosa, European standard EN ISO 16266:2008 entitled “Water quality - Detection and enumeration of Pseudomonas aeruginosa - Method by membrane filtration (ISO 16266:2006)”;
(d)for colony count 22 °C (the enumeration of culturable microorganisms — colony count after aerobic incubation at 22 °C), European standard EN ISO 6222:1999 entitled “Water quality - Enumeration of culturable micro-organisms - Colony count by inoculation in a nutrient agar culture medium (ISO 6222:1999)”;
(e)for colony count 36 °C (the enumeration of culturable microorganisms — colony count after aerobic incubation at 36 °C), European standard EN ISO 6222:1999 entitled “Water quality - Enumeration of culturable micro-organisms - Colony count by inoculation in a nutrient agar culture medium (ISO 6222:1999)”; and
(f)for Clostridium perfringens including spores, European standard EN ISO 14189:2016 entitled “Water quality - Enumeration of Clostridium perfringens - Method using membrane filtration (ISO 14189:2013)”.
1.—(1) Subject to paragraph 3, for a parameter in Table 1, the method of analysis used must, as a minimum, be capable of measuring concentrations equal to the prescribed concentration or value for the parameter with—S
(a)a limit of quantification of 30 % or less of the prescribed concentration or value for the parameter; and
(b)an uncertainty of measurement as specified in Table 1 for the parameter.
(2) The result of the analysis for a parameter in Table B or Table C must be expressed using at least the same number of significant figures as the prescribed concentration or value for the parameter in the table.
2. The uncertainty of measurement specified in Table 1 for a parameter must not be used as an additional tolerance to the prescribed concentration or value for the parameter.S
3. Until 31st December 2019, Scottish Water may, for a parameter in Table 2, use the corresponding ‘trueness’, ‘precision’ and ‘limit of detection’ in that table as an alternative set of performance characteristics (instead of using the limit of quantification and the uncertainty of measurement referred to in paragraph 1(1)).S
Parameter | Uncertainty of measurement (% of prescribed concentration or value, except pH) (Note 1) | Notes |
---|---|---|
Aluminium | 25 | |
Ammonium | 40 | |
Antimony | 40 | |
Arsenic | 30 | |
Benzo(a)pyrene | 50 | Note 5 |
Benzene | 40 | |
Boron | 25 | |
Bromate | 40 | |
Cadmium | 25 | |
Chloride | 15 | |
Chromium | 30 | |
Conductivity | 20 | |
Copper | 25 | |
Cyanide | 30 | Note 6 |
1,2-dichloroethane | 40 | |
Fluoride | 20 | |
Hydrogen ion concentration (in pH) | 0.2 | Note 7 |
Iron | 30 | |
Lead | 25 | |
Manganese | 30 | |
Mercury | 30 | |
Nickel | 25 | |
Nitrate | 15 | |
Nitrite | 20 | |
Oxidisability | 50 | Note 8 |
Pesticides | 30 | Note 9 |
Polycyclic aromatic hydrocarbons | 50 | Note 10 |
Selenium | 40 | |
Sodium | 15 | |
Sulphate | 15 | |
Tetrachloroethene | 30 | Note 11 |
Trichloroethene | 40 | Note 11 |
Trihalomethanes: total | 40 | Note 10 |
Total organic carbon | 30 | Note 12 |
Turbidity | 30 | Note 13 |
Parameter | Trueness (% of prescribed concentration or value, except for pH) (Note 2) | Precision (% of prescribed concentration or value, except for pH) (Note 3) | Limit of detection (% of prescribed concentration or value, except for pH) (Note 4) | Notes |
---|---|---|---|---|
Aluminium | 10 | 10 | 10 | |
Ammonium | 10 | 10 | 10 | |
Antimony | 25 | 25 | 25 | |
Arsenic | 10 | 10 | 10 | |
Benzo(a)pyrene | 25 | 25 | 25 | |
Benzene | 25 | 25 | 25 | |
Boron | 10 | 10 | 10 | |
Bromate | 25 | 25 | 25 | |
Cadmium | 10 | 10 | 10 | |
Chloride | 10 | 10 | 10 | |
Chromium | 10 | 10 | 10 | |
Conductivity | 10 | 10 | 10 | |
Copper | 10 | 10 | 10 | |
Cyanide | 10 | 10 | 10 | Note 6 |
1,2-dichloroethane | 25 | 25 | 10 | |
Fluoride | 10 | 10 | 10 | |
Hydrogen ion concentration (in pH) | 0.2 | 0.2 | Note 7 | |
Iron | 10 | 10 | 10 | |
Lead | 10 | 10 | 10 | |
Manganese | 10 | 10 | 10 | |
Mercury | 20 | 10 | 20 | |
Nickel | 10 | 10 | 10 | |
Nitrate | 10 | 10 | 10 | |
Nitrite | 10 | 10 | 10 | |
Oxidisability | 25 | 25 | 10 | Note 8 |
Pesticides | 25 | 25 | 25 | Note 9 |
Polycyclic aromatic hydrocarbons | 25 | 25 | 25 | Note 10 |
Selenium | 10 | 10 | 10 | |
Sodium | 10 | 10 | 10 | |
Sulphate | 10 | 10 | 10 | |
Tetrachloroethene | 25 | 25 | 10 | Note 11 |
Trichloroethene | 25 | 25 | 10 | Note 11 |
Trihalomethanes: total | 25 | 25 | 10 | Note 10 |
Turbidity | 25 | 25 | 25 | |
Notes to Table 1 and Table 2 | ||||
Note 1: Uncertainty of measurement is a non-negative parameter characterising the dispersion of the quantity values being attributed to a measurand, based on the information used. The performance criterion for measurement uncertainty (k = 2) is the percentage of the prescribed concentration or value for the parameter stated in the table or better. Measurement uncertainty must be estimated at the level of the prescribed concentration or value for the parameter, unless otherwise specified. | ||||
Note 2: Trueness is a measure of systematic error, i.e. the difference between the mean value of the large number of repeated measurements and the true value. Further specifications are those set out in international standard ISO 5725 entitled “Accuracy (trueness and precision) of measurement methods and results”. | ||||
Note 3: Precision is a measure of random error and is usually expressed as the standard deviation (within and between batches) of the spread of results from the mean. Acceptable precision is twice the relative standard deviation. This term is further specified in international standard ISO 5725 entitled “Accuracy (trueness and precision) of measurement methods and results”. | ||||
Note 4: Limit of detection is either three times the standard deviation within a batch of a natural sample containing a low concentration of the parameter, or five times the standard deviation of a blank sample (within a batch). | ||||
Note 5: If the value of uncertainty of measurement cannot be met, the best available technique should be selected (up to 60 %). | ||||
Note 6: The method determines total cyanide in all forms. | ||||
Note 7: Values for trueness, precision and uncertainty of measurement are expressed in pH units. | ||||
Note 8: Reference method European standard EN ISO 8467:1995 entitled “Water quality - Determination of permanganate index (ISO 8467:1993)”. | ||||
Note 9: The performance characteristics for individual pesticides are given as an indication. Values for the uncertainty of measurement as low as 30 % can be achieved for several pesticides, higher values up to 80 % may be allowed for a number of pesticides. | ||||
Note 10: The performance characteristics apply to individual substances, specified at 25 % of the prescribed concentration or value for the corresponding parameter in Table B. | ||||
Note 11: The performance characteristics apply to individual substances, specified at 50 % of the prescribed concentration or value for the corresponding parameter in Table B. | ||||
Note 12: The uncertainty of measurement should be estimated at the level of 3 mg/l of the total organic carbon in accordance with European standard EN 1484:1997 entitled “Water analysis - Guidelines for the determination of total organic carbon and dissolved organic carbon”. | ||||
Note 13: The uncertainty of measurement must be estimated at the level of 1.0 nephelometric turbidity units in accordance with European standard EN ISO 7027-1:2016 entitled “Water quality - Determination of turbidity - Part 1: Quantitative methods (ISO 7027-1:2016)”. |
For each parameter in Table 3, the method of analysis used must be capable of measuring activity concentrations with at least the limit of detection specified for that parameter in the second column of the table.
Parameter | Limit of detection (in Bq/l) (Notes 1 and 2) | Notes |
---|---|---|
Tritium | 10 | Note 3 |
Radon | 10 | Note 3 |
gross alpha activity | 0.04 | Note 4 |
gross beta activity | 0.4 | Note 4 |
U-238 | 0.02 | |
U-234 | 0.02 | |
Ra-226 | 0.04 | |
Ra-228 | 0.02 | Note 5 |
Pb-210 | 0.02 | |
Po-210 | 0.01 | |
C-14 | 20 | |
Sr-90 | 0.4 | |
Pu-239 / Pu-240 | 0.04 | |
Am-241 | 0.06 | |
Co-60 | 0.5 | |
Cs-134 | 0.5 | |
Cs-137 | 0.5 | |
I-131 | 0.5 | |
Notes to Table 3 | ||
Note 1: The limit of detection must be calculated in accordance with the international standard ISO 11929:2010 entitled “Determination of the characteristic limits (decision threshold, detection limit and limits of the confidence interval) for measurements of ionising radiation - Fundamentals and application”, with probabilities of errors of 1st and 2nd kind of 0.05 each. | ||
Note 2: Measurement uncertainties must be calculated and reported as complete standard uncertainties, or as expanded standard uncertainties with an expansion factor of 1.96, in accordance with international standard ISO/IEC Guide 98-3:2008 entitled “Guide to the expression of uncertainty in measurement”. | ||
Note 3: The limit of detection for tritium and for radon is 10% of the corresponding prescribed concentration or value for the parameter. | ||
Note 4: The limit of detection for gross alpha activity and gross beta activities is 40% of the screening values of 0.1 Bq/l and 1.0 Bq/l respectively. | ||
Note 5: This limit of detection applies only to initial screening for indicative dose for a new water source. If initial checking indicates that it is unlikely that Ra-228 exceeds 20% of the derived concentration, the limit of detection may be increased to 0.08 Bq/l for routine Ra-228 nuclide specific measurements, until a subsequent re-check is required.] |
Regulation 6(6A)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Textual Amendments
F18Sch. 3A omitted (27.10.2017) by virtue of The Public Water Supplies (Scotland) Amendment Regulations 2017 (S.S.I. 2017/281), regs. 1(1), 11
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As Enacted or Made): The original version of the legislation as it stood when it was enacted or made. No changes have been applied to the text.
Point in Time: This becomes available after navigating to view revised legislation as it stood at a certain point in time via Advanced Features > Show Timeline of Changes or via a point in time advanced search.
Geographical Extent: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Show Timeline of Changes: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Policy Note sets out a brief statement of the purpose of a Scottish Statutory Instrument and provides information about its policy objective and policy implications. They aim to make the Scottish Statutory Instrument accessible to readers who are not legally qualified and accompany any Scottish Statutory Instrument or Draft Scottish Statutory Instrument laid before the Scottish Parliament from July 2012 onwards. Prior to this date these type of notes existed as ‘Executive Notes’ and accompanied Scottish Statutory Instruments from July 2005 until July 2012.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
This timeline shows the different points in time where a change occurred. The dates will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. The first date in the timeline will usually be the earliest date when the provision came into force. In some cases the first date is 01/02/1991 (or for Northern Ireland legislation 01/01/2006). This date is our basedate. No versions before this date are available. For further information see the Editorial Practice Guide and Glossary under Help.
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: