- Latest available (Revised)
- Point in Time (21/11/2018)
- Original (As adopted by EU)
Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (recast) (Text with EEA relevance)
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).
Version Superseded: 22/07/2019
EU Directives are published on this site to aid cross referencing from UK legislation. Since IP completion day (31 December 2020 11.00 p.m.) no amendments have been applied to this version.
Lead (0,1 %)
Mercury (0,1 %)
Cadmium (0,01 %)
Hexavalent chromium (0,1 %)
Polybrominated biphenyls (PBB) (0,1 %)
Polybrominated diphenyl ethers (PBDE) (0,1 %)
b [F1Directive 97/68/EC of the European Parliament and of the Council of 16 December 1997 on the approximation of the laws of the Member States relating to measures against the emission of gaseous and particulate pollutants from internal combustion engines to be installed in non-road mobile machinery ( OJ L 59, 27.2.1998, p. 1 ).] | ||
Exemption | Scope and dates of applicability | |
---|---|---|
1 | Mercury in single capped (compact) fluorescent lamps not exceeding (per burner): | |
1(a) | For general lighting purposes < 30 W: 5 mg | Expires on 31 December 2011; 3,5 mg may be used per burner after 31 December 2011 until 31 December 2012; 2,5 mg shall be used per burner after 31 December 2012 |
1(b) | For general lighting purposes ≥ 30 W and < 50 W: 5 mg | Expires on 31 December 2011; 3,5 mg may be used per burner after 31 December 2011 |
1(c) | For general lighting purposes ≥ 50 W and < 150 W: 5 mg | |
1(d) | For general lighting purposes ≥ 150 W: 15 mg | |
1(e) | For general lighting purposes with circular or square structural shape and tube diameter ≤ 17 mm | No limitation of use until 31 December 2011; 7 mg may be used per burner after 31 December 2011 |
1(f) | For special purposes: 5 mg | |
[F21(g) | For general lighting purposes < 30 W with a lifetime equal or above 20 000 h: 3,5 mg | Expires on 31 December 2017] |
2(a) | Mercury in double-capped linear fluorescent lamps for general lighting purposes not exceeding (per lamp): | |
2(a)(1) | Tri-band phosphor with normal lifetime and a tube diameter < 9 mm (e.g. T2): 5 mg | Expires on 31 December 2011; 4 mg may be used per lamp after 31 December 2011 |
2(a)(2) | Tri-band phosphor with normal lifetime and a tube diameter ≥ 9 mm and ≤ 17 mm (e.g. T5): 5 mg | Expires on 31 December 2011; 3 mg may be used per lamp after 31 December 2011 |
2(a)(3) | Tri-band phosphor with normal lifetime and a tube diameter > 17 mm and ≤ 28 mm (e.g. T8): 5 mg | Expires on 31 December 2011; 3,5 mg may be used per lamp after 31 December 2011 |
2(a)(4) | Tri-band phosphor with normal lifetime and a tube diameter > 28 mm (e.g. T12): 5 mg | Expires on 31 December 2012; 3,5 mg may be used per lamp after 31 December 2012 |
2(a)(5) | Tri-band phosphor with long lifetime (≥ 25 000 h): 8 mg | Expires on 31 December 2011; 5 mg may be used per lamp after 31 December 2011 |
2(b) | Mercury in other fluorescent lamps not exceeding (per lamp): | |
2(b)(1) | Linear halophosphate lamps with tube > 28 mm (e.g. T10 and T12): 10 mg | Expires on 13 April 2012 |
2(b)(2) | Non-linear halophosphate lamps (all diameters): 15 mg | Expires on 13 April 2016 |
2(b)(3) | Non-linear tri-band phosphor lamps with tube diameter > 17 mm (e.g. T9) | No limitation of use until 31 December 2011; 15 mg may be used per lamp after 31 December 2011 |
2(b)(4) | Lamps for other general lighting and special purposes (e.g. induction lamps) | No limitation of use until 31 December 2011; 15 mg may be used per lamp after 31 December 2011 |
3 | Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps (CCFL and EEFL) for special purposes not exceeding (per lamp): | |
3(a) | Short length (≤ 500 mm) | No limitation of use until 31 December 2011; 3,5 mg may be used per lamp after 31 December 2011 |
3(b) | Medium length (> 500 mm and ≤ 1 500 mm) | No limitation of use until 31 December 2011; 5 mg may be used per lamp after 31 December 2011 |
3(c) | Long length (> 1 500 mm) | No limitation of use until 31 December 2011; 13 mg may be used per lamp after 31 December 2011 |
4(a) | Mercury in other low pressure discharge lamps (per lamp) | No limitation of use until 31 December 2011; 15 mg may be used per lamp after 31 December 2011 |
4(b) | Mercury in High Pressure Sodium (vapour) lamps for general lighting purposes not exceeding (per burner) in lamps with improved colour rendering index Ra > 60: | |
4(b)-I | P ≤ 155 W | No limitation of use until 31 December 2011; 30 mg may be used per burner after 31 December 2011 |
4(b)-II | 155 W < P ≤ 405 W | No limitation of use until 31 December 2011; 40 mg may be used per burner after 31 December 2011 |
4(b)-III | P > 405 W | No limitation of use until 31 December 2011; 40 mg may be used per burner after 31 December 2011 |
4(c) | Mercury in other High Pressure Sodium (vapour) lamps for general lighting purposes not exceeding (per burner): | |
4(c)-I | P ≤ 155 W | No limitation of use until 31 December 2011; 25 mg may be used per burner after 31 December 2011 |
4(c)-II | 155 W < P ≤ 405 W | No limitation of use until 31 December 2011; 30 mg may be used per burner after 31 December 2011 |
4(c)-III | P > 405 W | No limitation of use until 31 December 2011; 40 mg may be used per burner after 31 December 2011 |
4(d) | Mercury in High Pressure Mercury (vapour) lamps (HPMV) | Expires on 13 April 2015 |
4(e) | Mercury in metal halide lamps (MH) | |
4(f) | Mercury in other discharge lamps for special purposes not specifically mentioned in this Annex | |
[F34(g) | Mercury in hand crafted luminous discharge tubes used for signs, decorative or architectural and specialist lighting and light-artwork, where the mercury content shall be limited as follows: (a) 20 mg per electrode pair + 0,3 mg per tube length in cm, but not more than 80 mg, for outdoor applications and indoor applications exposed to temperatures below 20 °C; (b) 15 mg per electrode pair + 0,24 mg per tube length in cm, but not more than 80 mg, for all other indoor applications. | Expires on 31 December 2018] |
5(a) | Lead in glass of cathode ray tubes | |
5(b) | Lead in glass of fluorescent tubes not exceeding 0,2 % by weight | |
6(a) | Lead as an alloying element in steel for machining purposes and in galvanised steel containing up to 0,35 % lead by weight | |
6(b) | Lead as an alloying element in aluminium containing up to 0,4 % lead by weight | |
6(c) | Copper alloy containing up to 4 % lead by weight | |
7(a) | Lead in high melting temperature type solders (i.e. lead-based alloys containing 85 % by weight or more lead) | |
7(b) | Lead in solders for servers, storage and storage array systems, network infrastructure equipment for switching, signalling, transmission, and network management for telecommunications | |
7(c)-I | Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound | |
7(c)-II | Lead in dielectric ceramic in capacitors for a rated voltage of 125 V AC or 250 V DC or higher | |
7(c)-III | Lead in dielectric ceramic in capacitors for a rated voltage of less than 125 V AC or 250 V DC | Expires on 1 January 2013 and after that date may be used in spare parts for EEE placed on the market before 1 January 2013 |
[F47(c)-IV | Lead in PZT based dielectric ceramic materials for capacitors which are part of integrated circuits or discrete semiconductors | Expires on 21 July 2016] |
8(a) | Cadmium and its compounds in one shot pellet type thermal cut-offs | Expires on 1 January 2012 and after that date may be used in spare parts for EEE placed on the market before 1 January 2012 |
8(b) | Cadmium and its compounds in electrical contacts | |
9 | Hexavalent chromium as an anticorrosion agent of the carbon steel cooling system in absorption refrigerators up to 0,75 % by weight in the cooling solution | |
[F59(b) | Lead in bearing shells and bushes for refrigerant-containing compressors for heating, ventilation, air conditioning and refrigeration (HVACR) applications | Applies to categories 8, 9 and 11; expires on:
|
9(b)-(I) | Lead in bearing shells and bushes for refrigerant-containing hermetic scroll compressors with a stated electrical power input equal or below 9 kW for heating, ventilation, air conditioning and refrigeration (HVACR) applications | Applies to category 1; expires on 21 July 2019 .] |
11(a) | Lead used in C-press compliant pin connector systems | May be used in spare parts for EEE placed on the market before 24 September 2010 |
11(b) | Lead used in other than C-press compliant pin connector systems | Expires on 1 January 2013 and after that date may be used in spare parts for EEE placed on the market before 1 January 2013 |
12 | Lead as a coating material for the thermal conduction module C-ring | May be used in spare parts for EEE placed on the market before 24 September 2010 |
[F613(a) | Lead in white glasses used for optical applications | Applies to all categories; expires on:
|
[F713(b) | Cadmium and lead in filter glasses and glasses used for reflectance standards | Applies to categories 8, 9 and 11; expires on:
|
13(b)-(I) | Lead in ion coloured optical filter glass types | Applies to categories 1 to 7 and 10; expires on 21 July 2021 for categories 1 to 7 and 10 |
13(b)-(II) | Cadmium in striking optical filter glass types; excluding applications falling under point 39 of this Annex | |
13(b)-(III) | Cadmium and lead in glazes used for reflectance standards] | |
14 | Lead in solders consisting of more than two elements for the connection between the pins and the package of microprocessors with a lead content of more than 80 % and less than 85 % by weight | Expired on 1 January 2011 and after that date may be used in spare parts for EEE placed on the market before 1 January 2011 |
15 | Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit flip chip packages | |
16 | Lead in linear incandescent lamps with silicate coated tubes | Expires on 1 September 2013 |
17 | Lead halide as radiant agent in high intensity discharge (HID) lamps used for professional reprography applications | |
18(a) | Lead as activator in the fluorescent powder (1 % lead by weight or less) of discharge lamps when used as speciality lamps for diazoprinting reprography, lithography, insect traps, photochemical and curing processes containing phosphors such as SMS ((Sr,Ba)2MgSi2O7:Pb) | Expired on 1 January 2011 |
18(b) | Lead as activator in the fluorescent powder (1 % lead by weight or less) of discharge lamps when used as sun tanning lamps containing phosphors such as BSP (BaSi2O5:Pb) | |
19 | Lead with PbBiSn-Hg and PbInSn-Hg in specific compositions as main amalgam and with PbSn-Hg as auxiliary amalgam in very compact energy saving lamps (ESL) | Expires on 1 June 2011 |
20 | Lead oxide in glass used for bonding front and rear substrates of flat fluorescent lamps used for Liquid Crystal Displays (LCDs) | Expires on 1 June 2011 |
21 | Lead and cadmium in printing inks for the application of enamels on glasses, such as borosilicate and soda lime glasses | |
23 | Lead in finishes of fine pitch components other than connectors with a pitch of 0,65 mm and less | May be used in spare parts for EEE placed on the market before 24 September 2010 |
24 | Lead in solders for the soldering to machined through hole discoidal and planar array ceramic multilayer capacitors | |
25 | Lead oxide in surface conduction electron emitter displays (SED) used in structural elements, notably in the seal frit and frit ring | |
26 | Lead oxide in the glass envelope of black light blue lamps | Expires on 1 June 2011 |
27 | Lead alloys as solder for transducers used in high-powered (designated to operate for several hours at acoustic power levels of 125 dB SPL and above) loudspeakers | Expired on 24 September 2010 |
29 | Lead bound in crystal glass as defined in Annex I (Categories 1, 2, 3 and 4) of Council Directive 69/493/EECa | |
30 | Cadmium alloys as electrical/mechanical solder joints to electrical conductors located directly on the voice coil in transducers used in high-powered loudspeakers with sound pressure levels of 100 dB (A) and more | |
31 | Lead in soldering materials in mercury free flat fluorescent lamps (which, e.g. are used for liquid crystal displays, design or industrial lighting) | |
32 | Lead oxide in seal frit used for making window assemblies for Argon and Krypton laser tubes | |
33 | Lead in solders for the soldering of thin copper wires of 100 μm diameter and less in power transformers | |
34 | Lead in cermet-based trimmer potentiometer elements | |
36 | Mercury used as a cathode sputtering inhibitor in DC plasma displays with a content up to 30 mg per display | Expired on 1 July 2010 |
37 | Lead in the plating layer of high voltage diodes on the basis of a zinc borate glass body | |
38 | Cadmium and cadmium oxide in thick film pastes used on aluminium bonded beryllium oxide | |
[F839(a) | Cadmium selenide in downshifting cadmium-based semiconductor nanocrystal quantum dots for use in display lighting applications (< 0,2 μg Cd per mm 2 of display screen area) | [X1Expires for all categories on 31 October 2019] ] |
[F940 | Cadmium in photoresistors for analogue optocouplers applied in professional audio equipment | Expires on 31 December 2013] |
[F141 | Lead in solders and termination finishes of electrical and electronic components and finishes of printed circuit boards used in ignition modules and other electrical and electronic engine control systems, which for technical reasons must be mounted directly on or in the crankcase or cylinder of hand-held combustion engines (classes SH:1, SH:2, SH:3 of Directive 97/68/EC of the European Parliament and of the Council b ) | Expires on 31 December 2018] |
Editorial Information
X1 Substituted by Corrigendum to Commission Delegated Directive (EU) 2017/1975 of 7 August 2017 amending, for the purposes of adapting to scientific and technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for cadmium in colour converting light-emitting diodes (LEDs) for use in display systems (Official Journal of the European Union L 281 of 31 October 2017).
Textual Amendments
F1 Inserted by Commission Delegated Directive 2014/72/EU of 13 March 2014 amending, for the purposes of adapting to technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in solders and termination finishes of electrical and electronic components and finishes of printed circuit boards used in ignition modules and other electrical and electronic engine control systems (Text with EEA relevance).
F2 Inserted by Commission Delegated Directive 2014/14/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for 3,5 mg mercury per lamp in single capped compact fluorescent lamps for general lighting purposes < 30 W with a lifetime equal to or above 20000 h (Text with EEA relevance).
F3 Inserted by Commission Delegated Directive 2014/76/EU of 13 March 2014 amending, for the purposes of adapting to technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for Mercury in hand crafted luminous discharge tubes (HLDTs) used for signs, decorative or architectural and specialist lighting and light-artwork (Text with EEA relevance).
F4 Inserted by Commission Delegated Directive 2012/50/EU of 10 October 2012 amending, for the purposes of adapting to technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for applications containing lead (Text with EEA relevance).
F5 Substituted by Commission Delegated Directive (EU) 2017/1010 of 13 March 2017 amending, for the purposes of adapting to technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in bearing shells and bushes for certain refrigerant-containing compressors (Text with EEA relevance).
F6 Substituted by Commission Delegated Directive (EU) 2017/1011 of 15 March 2017 amending, for the purposes of adapting to technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in white glasses used for optical applications (Text with EEA relevance).
F7 Substituted by Commission Delegated Directive (EU) 2017/1009 of 13 March 2017 amending, for the purposes of adapting to technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for cadmium and lead in filter glasses and glasses used for reflectance standards (Text with EEA relevance).
F8 Substituted by Commission Delegated Directive (EU) 2017/1975 of 7 August 2017 amending, for the purposes of adapting to scientific and technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for cadmium in colour converting light-emitting diodes (LEDs) for use in display systems (Text with EEA relevance).
F9 Inserted by Commission Delegated Directive 2012/51/EU of 10 October 2012 amending, for the purposes of adapting to technical progress, Annex III to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for applications containing cadmium (Text with EEA relevance).
Textual Amendments
F10 Substituted by Commission Delegated Directive 2014/9/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead and cadmium in metallic bonds creating superconducting magnetic circuits in MRI, SQUID, NMR (Nuclear Magnetic Resonance) or FTMS (Fourier Transform Mass Spectrometer) detectors (Text with EEA relevance).
Textual Amendments
F11 Inserted by Commission Delegated Directive 2014/2/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for cadmium in phosphor coatings in image intensifiers for X-ray images until 31 December 2019 and in spare parts for X-ray systems placed on the EU market before 1 January 2020 (Text with EEA relevance).
Textual Amendments
F12 Inserted by Commission Delegated Directive 2014/3/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead acetate marker for use in stereotactic head frames for use with CT (Computed Tomography) and MRI and in positioning systems for gamma beam and particle therapy equipment (Text with EEA relevance).
Textual Amendments
F13 Inserted by Commission Delegated Directive 2014/1/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead as an alloying element for bearings and wear surfaces in medical equipment exposed to ionising radiation (Text with EEA relevance).
Textual Amendments
F14 Inserted by Commission Delegated Directive 2014/4/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead enabling vacuum tight connections between aluminium and steel in X-ray image intensifiers (Text with EEA relevance).
Textual Amendments
F15 Inserted by Commission Delegated Directive 2014/6/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in the surface coatings of pin connector systems requiring nonmagnetic connectors which are used durably at a temperature below – 20 °C under normal operating and storage conditions (Text with EEA relevance).
solders on printed circuit boards;
termination coatings of electrical and electronic components and coatings of printed circuit boards;
solders for connecting wires and cables;
solders connecting transducers and sensors.
Lead in solders of electrical connections to temperature measurement sensors in devices which are designed to be used periodically at temperatures below – 150 °C.
These exemptions expire on 30 June 2021 .]
Textual Amendments
F16 Substituted by Commission Delegated Directive (EU) 2016/1028 of 19 April 2016 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in solders of electrical connections to temperature measurement sensors in certain devices (Text with EEA relevance).
solders,
termination coatings of electrical and electronic components and printed circuit boards,
connections of electrical wires, shields and enclosed connectors,
which are used in
magnetic fields within the sphere of 1 m radius around the isocentre of the magnet in medical magnetic resonance imaging equipment, including patient monitors designed to be used within this sphere, or
magnetic fields within 1 m distance from the external surfaces of cyclotron magnets, magnets for beam transport and beam direction control applied for particle therapy.
Expires on 30 June 2020 .]
Textual Amendments
F17 Inserted by Commission Delegated Directive 2014/7/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in solders, termination coatings of electrical and electronic components and printed circuit boards, connections of electrical wires, shields and enclosed connectors which are used (a) in magnetic fields within the sphere of 1 m radius around the isocentre of the magnet in medical magnetic resonance imaging equipment, including patient monitors designed to be used within this sphere, or (b) in magnetic fields within 1 m distance from the external surfaces of cyclotron magnets, magnets for beam transport and beam direction control applied for particle therapy (Text with EEA relevance).
Textual Amendments
F18 Inserted by Commission Delegated Directive 2014/8/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in solders for mounting cadmium telluride and cadmium zinc telluride digital array detectors to printed circuit boards (Text with EEA relevance).
Textual Amendments
F19 Inserted by Commission Delegated Directive 2014/10/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in alloys, as a superconductor or thermal conductor, used in cryo-cooler cold heads and/or in cryo-cooled cold probes and/or in cryo-cooled equipotential bonding systems, in medical devices (category 8) and/or in industrial monitoring and control instruments (Text with EEA relevance).
Textual Amendments
F20 Inserted by Commission Delegated Directive 2014/11/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for hexavalent chromium in alkali dispensers used to create photocathodes in X-ray image intensifiers until 31 December 2019 and in spare parts for X-ray systems placed on the EU market before 1 January 2020 (Text with EEA relevance).
Textual Amendments
F21 Deleted by Commission Delegated Directive (EU) 2016/585 of 12 February 2016 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead, cadmium, hexavalent chromium, and polybrominated diphenyl ethers (PBDE) in spare parts recovered from and used for the repair or refurbishment of medical devices or electron microscopes (Text with EEA relevance).
Expires on:
21 July 2021 for the use in medical devices other than in vitro diagnostic medical devices;
21 July 2023 for the use in in vitro diagnostic medical devices;
21 July 2024 for the use in electron microscopes and their accessories.]
Textual Amendments
F22 Inserted by Commission Delegated Directive (EU) 2016/585 of 12 February 2016 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead, cadmium, hexavalent chromium, and polybrominated diphenyl ethers (PBDE) in spare parts recovered from and used for the repair or refurbishment of medical devices or electron microscopes (Text with EEA relevance).
Textual Amendments
F23 Inserted by Commission Delegated Directive 2014/12/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in solders on printed circuit boards of detectors and data acquisition units for Positron Emission Tomographs which are integrated into Magnetic Resonance Imaging equipment (Text with EEA relevance).
Textual Amendments
F24 Inserted by Commission Delegated Directive 2014/13/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in solders on populated printed circuit boards used in Directive 93/42/EEC class IIa and IIb mobile medical devices other than portable emergency defibrillators (Text with EEA relevance).
Textual Amendments
F25 Inserted by Commission Delegated Directive 2014/16/EU of 18 October 2013 amending, for the purposes of adapting to technical progress, the Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead as an activator in the fluorescent powder of discharge lamps when used for extracorporeal photopheresis lamps containing BSP (BaSi2O5:Pb) phosphors (Text with EEA relevance).
Expires on 21 July 2024 .]
Textual Amendments
F26 Inserted by Commission Delegated Directive 2014/75/EU of 13 March 2014 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for mercury in cold cathode fluorescent lamps (CCFLs) for back-lighting liquid crystal displays, not exceeding 5 mg per lamp, used in industrial monitoring and control instruments placed on the market before 22 July 2017 (Text with EEA relevance).
Expires on 31 December 2020 . May be used after that date in spare parts for industrial monitoring and control instruments placed on the market before 1 January 2021 .]
Textual Amendments
F27 Inserted by Commission Delegated Directive 2014/74/EU of 13 March 2014 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead used in other than C-press compliant pin connector systems for industrial monitoring and control instruments (Text with EEA relevance).
wide-range measurements with a conductivity range covering more than 1 order of magnitude (e.g. range between 0,1 mS/m and 5 mS/m) in laboratory applications for unknown concentrations;
measurements of solutions where an accuracy of +/– 1 % of the sample range and where high corrosion resistance of the electrode are required for any of the following:
solutions with an acidity < pH 1;
solutions with an alkalinity > pH 13;
corrosive solutions containing halogen gas;
measurements of conductivities above 100 mS/m that must be performed with portable instruments.
Expires on 31 December 2018 .]
Textual Amendments
F28 Inserted by Commission Delegated Directive 2014/73/EU of 13 March 2014 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in platinized platinum electrodes used for conductivity measurements (Text with EEA relevance).
Expires on 31 December 2019 . May be used after that date in spare parts for CT and X-ray systems placed on the market before 1 January 2020 .]
Textual Amendments
F29 Inserted by Commission Delegated Directive 2014/71/EU of 13 March 2014 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in solder in one interface of large area stacked die elements (Text with EEA relevance).
a compact size of the detector for electrons or ions, where the space for the detector is limited to a maximum of 3 mm/MCP (detector thickness + space for installation of the MCP), a maximum of 6 mm in total, and an alternative design yielding more space for the detector is scientifically and technically impracticable;
a two-dimensional spatial resolution for detecting electrons or ions, where at least one of the following applies:
a response time shorter than 25 ns;
a sample detection area larger than 149 mm 2 ;
a multiplication factor larger than 1,3 × 10 3 .
a response time shorter than 5 ns for detecting electrons or ions;
a sample detection area larger than 314 mm 2 for detecting electrons or ions;
a multiplication factor larger than 4,0 × 10 7 .
The exemption expires on the following dates:
21 July 2021 for medical devices and monitoring and control instruments;
21 July 2023 for in-vitro diagnostic medical devices;
21 July 2024 for industrial monitoring and control instruments.]
Textual Amendments
F30 Inserted by Commission Delegated Directive 2014/70/EU of 13 March 2014 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in micro-channel plates (MCPs) (Text with EEA relevance).
Expires on 31 December 2020 . May be used after that date in spare parts for industrial monitoring and control instruments placed on the market before 1 January 2021 .]
Textual Amendments
F31 Inserted by Commission Delegated Directive 2014/69/EU of 13 March 2014 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in dielectric ceramic in capacitors for a rated voltage of less than 125 V AC or 250 V DC for industrial monitoring and control instruments (Text with EEA relevance).
Expires on 31 December 2018 .]
Textual Amendments
F32 Inserted by Commission Delegated Directive (EU) 2015/573 of 30 January 2015 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for lead in polyvinyl chloride sensors in in-vitro diagnostic medical devices (Text with EEA relevance).
Expires on 30 June 2019 .]
Textual Amendments
F33 Inserted by Commission Delegated Directive (EU) 2015/574 of 30 January 2015 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for mercury in intravascular ultrasound imaging systems (Text with EEA relevance).
Expires on 15 July 2023 .]
Textual Amendments
F34 Inserted by Commission Delegated Directive (EU) 2016/1029 of 19 April 2016 amending, for the purposes of adapting to technical progress, Annex IV to Directive 2011/65/EU of the European Parliament and of the Council as regards an exemption for cadmium anodes in Hersch cells for certain oxygen sensors used in industrial monitoring and control instruments (Text with EEA relevance).
Applications for exemptions, renewal of exemptions or, mutatis mutandis, for revoking an exemption may be submitted by a manufacturer, the authorised representative of a manufacturer, or any economic operator in the supply chain and shall include at least the following:
the name, address and contact details of the applicant;
information on the material or component and the specific uses of the substance in the material and component for which an exemption, or its revocation, is requested and its particular characteristics;
verifiable and referenced justification for an exemption, or its revocation, in line with the conditions established in Article 5;
an analysis of possible alternative substances, materials or designs on a life-cycle basis, including, when available, information about independent research, peer-review studies and development activities by the applicant and an analysis of the availability of such alternatives;
information on the possible preparation for reuse or recycling of materials from waste EEE, and on the provisions relating to the appropriate treatment of waste according to Annex II to Directive 2002/96/EC;
other relevant information;
the proposed actions to develop, request the development and/or to apply possible alternatives including a timetable for such actions by the applicant;
where appropriate, an indication of the information which should be regarded as proprietary accompanied by verifiable justification;
when applying for an exemption, proposal for a precise and clear wording for the exemption;
a summary of the application.
Signed for and on behalf of: …
(place and date of issue):
(name, function) (signature):
(referred to in Article 26)
Directive 2002/95/EC of the European Parliament and of the Council | (OJ L 37, 13.2.2003, p. 19). |
Commission Decision 2005/618/EC | (OJ L 214, 19.8.2005, p. 65). |
Commission Decision 2005/717/EC | (OJ L 271, 15.10.2005, p. 48). |
Commission Decision 2005/747/EC | (OJ L 280, 25.10.2005, p. 18). |
Commission Decision 2006/310/EC | (OJ L 115, 28.4.2006, p. 38). |
Commission Decision 2006/690/EC | (OJ L 283, 14.10.2006, p. 47). |
Commission Decision 2006/691/EC | (OJ L 283, 14.10.2006, p. 48). |
Commission Decision 2006/692/EC | (OJ L 283, 14.10.2006, p. 50). |
Directive 2008/35/EC of the European Parliament and of the Council | (OJ L 81, 20.3.2008, p. 67). |
Commission Decision 2008/385/EC | (OJ L 136, 24.5.2008, p. 9). |
Commission Decision 2009/428/EC | (OJ L 139, 5.6.2009, p. 32). |
Commission Decision 2009/443/EC | (OJ L 148, 11.6.2009, p. 27). |
Commission Decision 2010/122/EU | (OJ L 49, 26.2.2010, p. 32). |
Commission Decision 2010/571/EU | (OJ L 251, 25.9.2010, p. 28). |
(referred to in Article 26)
Directive | Deadline for transposition |
---|---|
2002/95/EC | 12 August 2004 |
2008/35/EC | — |
Directive 2002/95/EC | This Directive |
---|---|
Article 1 | Article 1 |
Article 2(1) | Article 2(1), 2(2), Annex I |
Article 2(2) | Article 2(3) |
Article 2(3) | Article 2(4), introductory wording |
— | Article 2(4) |
Article 3(a) | Article 3(1),(2) |
Article 3(b) | — |
— | Article 3(6)-(28) |
Article 4(1) | Article 4(1), Annex II |
— | Article 4(3)-(4) |
Article 4(2) | Article 4(6) |
Article 4(3) | — |
Article 5(1), introductory wording | Article 5(1), introductory wording |
Article 5(1)(a) | Article 4(2) |
Article 5(1)(b) | Article 5(1)(a), first and third indents |
— | Article 5(1)(a), second indent Article 5(1)(a), final paragraph |
Article 5(1)(c) | Article 5(1)(b) |
— | Article 5(2) Article 5(3)-(6) |
Article 5(2) | Article 5(7) |
— | Article 5(8) |
Article 6 | Article 6 |
— | Article 7-18 |
Article 7 | Articles 19-22 |
Article 8 | Article 23 |
Article 9 | Article 25 |
— | Article 26 |
Article 10 | Article 27 |
Article 11 | Article 28 |
— | Annexes I-II |
Annex, points 1-39 | Annex III, points 1-39 |
— | Annexes IV, V, VI-VIII |
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Point in Time: This becomes available after navigating to view revised legislation as it stood at a certain point in time via Advanced Features > Show Timeline of Changes or via a point in time advanced search.
Geographical Extent: Indicates the geographical area that this provision applies to. For further information see ‘Frequently Asked Questions’.
Show Timeline of Changes: See how this legislation has or could change over time. Turning this feature on will show extra navigation options to go to these specific points in time. Return to the latest available version by using the controls above in the What Version box.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
This timeline shows the different versions taken from EUR-Lex before exit day and during the implementation period as well as any subsequent versions created after the implementation period as a result of changes made by UK legislation.
The dates for the EU versions are taken from the document dates on EUR-Lex and may not always coincide with when the changes came into force for the document.
For any versions created after the implementation period as a result of changes made by UK legislation the date will coincide with the earliest date on which the change (e.g an insertion, a repeal or a substitution) that was applied came into force. For further information see our guide to revised legislation on Understanding Legislation.
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: