Commission Regulation (EU) 2017/1151Show full title

Article 15 U.K. Transitional provisions

1. Until 31 August 2017 in the case of categories M1, M2 and category N1 class I vehicles, and until 31 August 2018 in the case of N1 vehicles of class II and III and category N2 vehicles manufacturers may request type-approval to be granted in accordance with this Regulation. Where such request is not made, Regulation (EC) No 692/2008 shall apply.

2. With effect from 1 September 2017 in the case of categories M1, M2 and category N1 class I vehicles, and from 1 September 2018 in the case of N1 vehicles of class II and III and category N2 vehicles, national authorities shall refuse, on grounds relating to emissions or fuel consumption, to grant EC type approval or national type approval, in respect to new vehicle types which do not comply with this Regulation.

3. With effect from 1 September 2018 in the case of categories M1, M2 and category N1 class I vehicles, and from 1 September 2019 in the case of N1 vehicles of class II and III and category N2 vehicles, national authorities shall, on grounds relating to emissions or fuel consumption, in the case of new vehicles which do not comply with this Regulation, consider certificates of conformity to be no longer valid for the purposes of Article 26 of Directive 2007/46/EC and shall prohibit the registration, sale or entry into service of such vehicles.

4. Until three years after the dates specified in Article 10(4) of Regulation (EC) No 715/2007 in the case of new vehicle types and four years after the dates specified in Article 10(5) of that Regulation in the case of new vehicles, the following provisions shall apply:

(a) the requirements of point 2.1 of Annex IIIA shall not apply;

(b) the requirements of Annex IIIA other than that in point 2.1, including the requirements with regard to RDE tests to be performed and data to be recorded and made available, shall apply only to new type approvals granted in accordance with Regulation (EC) No 715/2007 from 27 July 2017;

(c) the requirements of Annex IIIA shall not apply to type approvals granted to small volume manufacturers;

(d) where the requirements set out in Appendices 5 and 6 of Annex IIIA are satisfied for only one of the two data evaluation methods described in those Appendices, one additional RDE test shall be performed;

where those requirements are again satisfied for only one method, the analysis of the completeness and normality shall be recorded for both methods and the calculation required by point 9.3 of Annex IIIA may be limited to the method for which the completeness and normality requirements are satisfied; the data of both RDE tests and of the analysis of the completeness and normality shall be recorded and made available for examining the difference in the results of the two data evaluation methods;

(e) the power at the wheels of the test vehicle shall be determined either by wheel hub torque measurement or from the CO₂ mass flow using ‘Velines’ in accordance with point 4 of Appendix 6 to Annex IIIA.

5. Until 8 years after the dates given in Article 10(4) of Regulation (EC) No 715/2007:

(a) type 1/I tests performed and completed in accordance to Regulation (EC) No 692/2008 until 3 years after the dates given in Article 10(4) of Regulation (EC) No 715/2007 shall be valid for the purposes of fulfilling the requirements of Annex VII and/or Appendix 1 to Annex XI to this Regulation;

(b) procedures performed in accordance with section 3.13. of Annex III to Regulation (EC) No 692/2008 until 3 years after the dates given in Article 10(4) of Regulation (EC) 715/2007 shall be accepted by the approval authority for the purposes of fulfilling the requirements of the second paragraph of point 1.1 of Appendix 1 to Sub-Annex 6 to Annex XXI of this Regulation.

6. In order to ensure a fair treatment of previously existing type-approvals, the Commission shall examine the consequences of Chapter V of Directive 2007/46/EC for the purposes of this Regulation.